Help - my airport won't configure
Hi
I have been using an airport express for a few months now and it has been working fine. Last night it stopped working and I tried to fix it but I think I have made matters worse! It is now telling me that airport is not configured and doesn't even recognise that I have an airport express plugged in in the same room (when I turn on the airport utility it says it can't find any wireless airport devices).
I'm really stuck as to what to do now and was hoping someone could help me as I am relying on being plugged into the ethernet at the moment which is thoroughly annoying!
Thanks
You need to give us a bit more information.
1. When you fixed it, did you reset it?
2. Does your express "join" your network through another router?
3. When you look for access points broadcasting in your neighbourhood, do you see it?
4. Is the light green on the AX, or is it blinking yellow?
I'm guessing here ...
If you reset the AX, it is probably broadcasting as an independent access point that is separate from your main access point. You will have to connect to your AX through ethernet cable, and reconfigure it to join and existing network (that being the network created by your primary access point.)
Similar Messages
-
Need help AT-dsp2200 won't configure with 4.9.01f nidaq
Recently tried to up grade to 5.1 labview from 5.0 this cause me
to loose controlle of me AT-dsp 2200 card to make a long story
short I have now gone to back to labview 5.0 with 4.9.0.1F and used the
device manger to install the DSP cca then set the adress to the defaut
140 then go back to the nidaq and try to run the configution test and
at this point I get an error that saids that my cca does not responed
at this adress I Know the cca is good.Problem solved - in this instance what we needed to do (and not documented ANYWHERE) is to save the configuration prior to attempting to test that configuration. Without doing so, the message one gets is that the card is not responding at that base address setting.
The detail I've provided is minimal, and serves only to act as a reminder should we encounter the problem somewhere down the line...if anyone out there wants more elaborate detail, I'd be happy to provide it...I have email notification set on if someone replies to this message, so I will see the request. -
Airport Express won't configure to by Airport extreme
I keep getting a error stating "the airport express is configured but we can't find it..." Anyone else solved this problem?
I did that and still got the error message. I got a link from someone on another board:
http://www.upgradeyourmac.co.uk/mainsite/MacOSQuestions/Q071.html
...that tells you to do the whole setup manually, and I managed to get it working. It seems there is an issue with the software (from a recent software update, I believe) that doesn't allow the 'assist me' set up to work. I just don't get this...Apple has, on numerous occasions, released Airport updates that have broken the darn thing. Do they not test these updates beforehand? For the record, I am not the only person to have experienced this issue.
Is there a quick and easy way to notify Apple about this? -
HELP! Files won't open and previously had Firefox icon instead of DW icons! Leap Year thing?
Hi! I went to update my website, which I do every night before the first day of every month and all the files had a FIrefox icon instead of the usual Dreamweaver one. I have shut down, reinstalled DW MX 2004 but the files still do not open. The icons have now changed to DW but they are not opening with right click, opening from Applications folder, double clicking the file, from get info and open with DW. I am stumped. HELP! Need to update for March 1st.
Is it something to do with Leap Year 29th Feb? Checked the clock in preferences but can't see how this affects it.
Firefox is always updated but the latest version does not seem to be as efficient as previous upgrades. We installed Chrome as well. Do they interfere with each other?Hi Ken
I wish the 7.1 updater download had helped but it didn¹t. All the files
were backed up before the installation, which went fine.
Mac 10.5.8
We used Disc Warrior to defrag the hard drive, which did not make a
difference.
We recently started using Chrome, so now have 3 browsers in the dock,
Safari, Firefox and Chrome. Do they interfere in any way with each other?
The files, which I hadn¹t touched for a month as I update on a monthly
basis, initially had the Firefox icon.
Below is the message to send to Apple, which did not go through their report
system! A little disillusioned with the service!
Model: iMac9,1, BootROM IM91.008D.B08, 2 processors, Intel Core 2 Duo, 3.06
GHz, 4 GB
Graphics: kHW_NVidiaGeForceGT130Item, NVIDIA GeForce GT 130,
spdisplays_pcie_device, 512 MB
Memory Module: global_name
AirPort: spairport_wireless_card_type_airport_extreme (0x14E4, 0x8E),
Broadcom BCM43xx 1.0 (5.10.91.22)
Bluetooth: Version 2.1.9f10, 2 service, 0 devices, 1 incoming serial ports
Network Service: Ethernet, Ethernet, en0
Network Service: AirPort, AirPort, en1
Serial ATA Device: WDC WD1001FALS-40K1B0, 931.51 GB
Serial ATA Device: PIONEER DVD-RW DVRTS08
USB Device: Built-in iSight, (null) mA
USB Device: Keyboard Hub, (null) mA
USB Device: iLok, (null) mA
USB Device: Apple Optical USB Mouse, (null) mA
USB Device: Apple Keyboard, (null) mA
USB Device: Deskjet 3840, (null) mA
USB Device: BRCM2046 Hub, (null) mA
USB Device: Bluetooth USB Host Controller, (null) mA
USB Device: IR Receiver, (null) mA
FireWire Device: d2 quadra (button), LaCie, 800mbit_speed
Does not mean a thing to me.
I am not late with updating the site, which is about New Zealand culture,
month by month (www.englishteacher.co.nz). Probably only the third time I
have been late since 2005. Not a huge amount of traffic, ~300 a month and
free access to content but I would like to solve this problem.
Could a reciprocal link have caused a problem?
At my wits end.
I really appreciate the help though.
Cheers Yvonne
From: Ken Binney <[email protected]>
Reply-To: <[email protected]>
Date: Wed, 29 Feb 2012 06:42:11 -0700
To: Yvonne and Bill Hynson <[email protected]>
Subject: HELP! Files won't open and previously had Firefox
icon instead of DW icons! Leap Year thing?
Re: HELP! Files won't open and previously had Firefox icon instead of DW
icons! Leap Year thing?
created by Ken Binney <http://forums.adobe.com/people/Ken+Binney> in
Dreamweaver - View the full discussion
<http://forums.adobe.com/message/4236682#4236682>
Not necessarily related, but did you also install the 7.1
updater? http://www.adobe.com/support/dreamweaver/downloads_updaters.html
Windows or MAC?
Replies to this message go to everyone subscribed to this thread, not
directly to the person who posted the message. To post a reply, either reply
to this email or visit the message page:
http://forums.adobe.com/message/4236682#4236682 To unsubscribe from this
thread, please visit the message page at
http://forums.adobe.com/message/4236682#4236682. In the Actions box on the
right, click the Stop Email Notifications link. Start a new discussion in
Dreamweaver by email
<mailto:[email protected].ad
obe.com> or at Adobe Forums
<http://forums.adobe.com/choose-container!input.jspa?contentType=1&container
Type=14&container=2240> For more information about maintaining your forum
email notifications please go to
http://forums.adobe.com/message/2936746#2936746. -
Just can't get Airport Express to configure: it worked at my mum's, but not at home!
Hello helpful people,
I am really hoping someone can think of what's going wrong with my set up. I keep getting an error message "an unexpected error occurred, please try again" when i try to do my configuration. I only want it to stream music from my ipad to my stereo. I would really prefer to do the set up only using an ipad, if at all possible.
I was given a shiny new Airport Express for Christmas. As i was staying at my mum's for two weeks, I plugged it into her stereo, and got it working. This was configured to join her existing wifi network, using only my iPad to set it up. The airport utility software was not used, as i didn't know it existed. All worked fine.
It looks as if my router is running WEP. So i gather i need airport utility to configure it. Airport utility says it can't detect a base station anywhere, even when inches away. There don't seem to be any options to get it to work differently.
I have reset and factory reset the device many times.
Some level of wireless access must be working on it, as it appears on my wireless list as a possible "set up airport express base station"
I go through the menus to set it up in the same way as at my mum's: selecting my existing wifi network to add it into, setting up a new base station password, and then watching and waiting.
Among the different resets and re-attempts i have done, it varies slightly in behaviour: the last time it failed it didn't get as far as asking for my wifi password.
After the error message i can't "try again" as suggested. It wipes out my wifi access, so i need to delete my existing wifi network (on the ipad) and re-add it to get an internet connection back again. I need to do a reset to get the "configure new base station" message back.
The differences between the two houses:
The stereo connection is different in the two houses: single 3.5mm jack into mum's; 3.5mm jack split into two needed for our stereo. I know it says you need to plug into the stereo first (and I have), but surely the device doesn't care which cable i use?
At my house, the wireless router and airport box are within 4m of each other. At my mother's it's more like 20m.
My wireless router is from O2 (now Sky), my mother's is plusnet.It looks as if my router is running WEP.
Virtually no security at all there, as there are numerous free utilities available on the Internet that will crack a WEP network in seconds. You might as well run the network wide open, since WEP offers about the same level of protection.
You will not be able to configure the Express using an iPhone, iPad, or any version of AirPort Utility that is 6.x or higher with your router set to use WEP "security". They will not work with WEP, since it is so long out of date and non-secure.
An older version of AirPort Utility 5.x might allow you to configure the Express using WEP security, but with no protection anyway, this would be of little value.
See if your router can be configured to use WPA2 Personal security or WPA/WPA2 Personal security. If it can, then you will be able to use an iPhone, iPad, or any version of AirPort Utility to configure the Express in just a few minutes.
If your router cannot be configured to use stronger current WPA settings, now might be a very good time to ask your service provider for a new router. -
Hi,
I just bought a new Macbook Pro 15" with SSD 256 Gb and its almost a brand-new (the 4th time to use the device) a while ago i was trying to connect to my home wireless network it said that the connection is timed out so i clicked the airport sign on the top it said that your airport is not configured then I restarted the system but it didn't restarted it showed the grey screen with the apple logo and the spinning wheel for more than 10min so I tried the force shutdown by pressing the power button till it switched off I waited for 5min then pressed the power button to start or boot the system and again the grey screen with the apple logo and the spinning wheel, I waited for more than 20min nothing changed, any solution please?
Your help is really appreciated"Thanks a lot i followed the instructions for safe mode (i found out that i was pressing the C button after restarting) i did whats written there but the repair couldn't be performed so in addition i needed to re-formate the HD so i erased the volume and then repaired the disk--> quite disk utilities --> start the installation from the installation DVD.
Thanks really appreciating your help -
AirPort won't auto connect after resetting admin password
The other day I reset my admin password using the install disk and now AirPort won't log on automatically when I start my laptop. Has this happened to any one else? I have tried going through the network preferences, internet connect, and tried a couple of other things and the problem hasn't been fixed.
Try the following, in order, until (hopefully) resolved:
1a. Delete Preferred Network(s)
System Preferences > Network > AirPort > Advanced > AirPort tab
Under "Preferred Networks," delete the network(s) you regularly use from the list.
1b. Delete AirPort Keychain Entries
Launch the "Keychain Access" application located in Applications/Utilties.
Click on the "Kind" filter at the top, and look for any "AirPort network password" entries...and delete them.
1c. Add Preferred Network(s)
System Preferences > Network > AirPort > Advanced > AirPort tab
Add the preferred network(s) using the "+" button.
Restart or log out then back in.
2. Move System Configuration Files
(Note: You will have to reestablish your network connections settings.)
Go to /Library/Preferences
Move the SystemConfiguration folder to the desktop.
Restart your Mac. (Note: OS X will rebuild the files that are now sitting on your desktop. If this doesn't resolve the issue, you can move the folder back to it's original location.) -
Silent database creation won't configure OEM
Hi All,
Windows Vista 64-bit Oracle 11.1.0.7
I am doing a silent creation of the database which creates the database fine but the OEM - Web front end is not created. I have run netca to create a listener before database creation. Here is my exact syntax I am using from the command prompt:
dbca -silent -sysPassword oracle -systemPassword oracle -continueOnNonFatalErrors true -gdbName 11GORA01 -createDatabase -templateName Test11g -emConfiguration LOCAL -dbsnmpPassword oracle -sysmanPassword oracle
If I then use dbca to try & configure the database options there is an error saying there is no appropriate listener found. There is one thing I did notice that when I did lsnrctl status the database name was in lower case and using the dbca the message 'Configure additional components for database "11GORA01" - is in upper case. Not sure if this is the problem.
Any help would be fantastic
Thanks
VicHi,
Silent database creation won't configure OEM
AFAIK, NO you have to configure separately.
Regards,
Taj -
Not sure where to post this. I'm at my whit's end and would appreciate some help. I mistakenly configured my ipod to a computer which is in another state and I think it is recognizing it as my "home computer". Today I uninstalled the software on the computer I am using now and tried to reinstall it. (it was connected fine until I messed with it, which I did to reinstall iTunes)Now it won't configure to this computer and I have no access to the other one! It happens to be my mother's house, so I called and had her uninstall all the ipod software on that computer, but I'm sure that isn't going to do anything. I have found it impossible to get help from Apple. Any advice? Thanks!!!
What happens when you try to set up your iPod in your home computer?
Is your iPod configured at your mom's house on a Mac or Windows?
You cannot use an iPod whose disk is configured for Macintosh on a Windows-compatible computer. However, you can restore the iPod disk to use it with a Windows-compatible computer. To do this, see "Restoring iPod to factory settings." http://docs.info.apple.com/article.html?artnum=60983
While a Windows formatted iPod may work on a Mac, Apple supports this configuration only with iPod shuffle. -
HT1338 my macbook pro airport won't turn on! What would be the problem?
my macbook pro airport won't turn on! What would be the problem?
I've tried to turn the airport on and it says my airport card is not installed...
it has always worked till today... bot from now on nothing seem to help the airport work...
Please help me!
ThanksYou could try deleting the airpot from the sidebar of system preferences/network. To do this,
1) export the preferences for your airport to your desktop by pressing the gear next to the plus and minus sign above the lock.
2) Delete your airport from the sidebar using the minus sign while the airport is selected.
3) After deleting the airport, apply the changes and then press the plus sign to create a new airport.
4) Then import the preferences back in and apply the changes again.
This may bring your airport back. It worked for me. Alternatively, people have been having success with changing the location of the airport.
Good Luck. -
HELP! Airport no longer turning on
All of a sudden Airport won't turn on from either the menubar icon or from the network preferences. It just doesn't react.
I was wondering if anyone knew how to fix this.
Thank you!I don't have help for you, but will note that on my new (refurb) iMac, updated as of this morning, my Airport is acting strangely and unpredictably.
The iMac is my "base" cpu; and I use Airport on my MacBook to network and for internet connect.
Both computers have 10.5.1.
Sometimes the MacBook can network hard drives (last night I used Screen Sharing); briefly I had internet sharing; at the moment the MacBook's Airport menu item is grayed out.
Sounds like a combination of newer processors (my "old" base cpu was a G5 mac mini--no problems) and 10.5.1, possibly the new security updates.
no answers for now, just diagnosis. -
Help my iPod won't let me download apps... I'll put my password in then it takes me to the app but then is just goes away then I do it again an it won't load or it will just go away again plz help I want to get apps
You said you updated yur 1G iPod to 4.2.1. A 1G can only go to 3.1.3 and thus you must have jailbroken it to get to 4.2.1 and that can cause problems.
ArealDJ wrote:
I have the same problem.. apps won't download and won't open. I have a 1st Gen ipod touch and recently upgraded my MacBook Pro (2012) and as soon as I upgraded the iPod Touch to 4.2.1, this happened. I restored to factory defaults and still cannot dl and open apps. Any way to diagnose this problem? Apple tech charges $29.99 for out of warranty products and if I am reluctant to pay with them telling me its simply a hardware problem. -
Need some help: my itunes won't sync with my iphone anymore. Both softwares are up to date and I've reinstalled itunes. After I reinstall, it syncs. But then when I reboot my computer, it no longer syncs anymore and I have to keep reinstalling itunes. Thoughts???
thought that it was possible to have the same iTunes library on any machine that was authorised, a kind of cloud-iTunes I guess.
That would convenient, but sadly it is not the case. Sorry!
Either way your welcome and best of luck!
B-rock -
Help on Oracle streams 11g configuration
Hi Streams experts
Can you please validate the following creation process steps ?
What is need to have streams doing is a one way replication of the AR
schema from a database to another database. Both DML and DDL shall do
the replication of the data.
Help on Oracle streams 11g configuration. I would also need your help
on the maintenance steps, controls and procedures
2 databases
1 src as source database
1 dst as destination database
replication type 1 way of the entire schema FaeterBR
Step 1. Set all databases in archivelog mode.
Step 2. Change initialization parameters for Streams. The Streams pool
size and NLS_DATE_FORMAT require a restart of the instance.
SQL> alter system set global_names=true scope=both;
SQL> alter system set undo_retention=3600 scope=both;
SQL> alter system set job_queue_processes=4 scope=both;
SQL> alter system set streams_pool_size= 20m scope=spfile;
SQL> alter system set NLS_DATE_FORMAT=
'YYYY-MM-DD HH24:MI:SS' scope=spfile;
SQL> shutdown immediate;
SQL> startup
Step 3. Create Streams administrators on the src and dst databases,
and grant required roles and privileges. Create default tablespaces so
that they are not using SYSTEM.
---at the src
SQL> create tablespace streamsdm datafile
'/u01/product/oracle/oradata/orcl/strepadm01.dbf' size 100m;
---at the replica:
SQL> create tablespace streamsdm datafile
---at both sites:
'/u02/oracle/oradata/str10/strepadm01.dbf' size 100m;
SQL> create user streams_adm
identified by streams_adm
default tablespace strepadm01
temporary tablespace temp;
SQL> grant connect, resource, dba, aq_administrator_role to
streams_adm;
SQL> BEGIN
DBMS_STREAMS_AUTH.GRANT_ADMIN_PRIVILEGE (
grantee => 'streams_adm',
grant_privileges => true);
END;
Step 4. Configure the tnsnames.ora at each site so that a connection
can be made to the other database.
Step 5. With the tnsnames.ora squared away, create a database link for
the streams_adm user at both SRC and DST. With the init parameter
global_name set to True, the db_link name must be the same as the
global_name of the database you are connecting to. Use a SELECT from
the table global_name at each site to determine the global name.
SQL> select * from global_name;
SQL> connect streams_adm/streams_adm@SRC
SQL> create database link DST
connect to streams_adm identified by streams_adm
using 'DST';
SQL> select sysdate from dual@DST;
SLQ> connect streams_adm/streams_adm@DST
SQL> create database link SRC
connect to stream_admin identified by streams_adm
using 'SRC';
SQL> select sysdate from dual@SRC;
Step 6. Control what schema shall be replicated
FaeterBR is the schema to be replicated
Step 7. Add supplemental logging to the FaeterBR schema on all the
tables?
SQL> Alter table FaeterBR.tb1 add supplemental log data
(ALL) columns;
SQL> alter table FaeterBR.tb2 add supplemental log data
(ALL) columns;
etc...
Step 8. Create Streams queues at the primary and replica database.
---at SRC (primary):
SQL> connect stream_admin/stream_admin@ORCL
SQL> BEGIN
DBMS_STREAMS_ADM.SET_UP_QUEUE(
queue_table => 'streams_adm.FaeterBR_src_queue_table',
queue_name => 'streams_adm.FaeterBR_src__queue');
END;
---At DST (replica):
SQL> connect stream_admin/stream_admin@STR10
SQL> BEGIN
DBMS_STREAMS_ADM.SET_UP_QUEUE(
queue_table => 'stream_admin.FaeterBR_dst_queue_table',
queue_name => 'stream_admin.FaeterBR_dst_queue');
END;
Step 9. Create the capture process on the source database (SRC).
SQL> BEGIN
DBMS_STREAMS_ADM.ADD_SCHEMA_RULES(
schema_name =>'FaeterBR',
streams_type =>'capture',
streams_name =>'FaeterBR_src_capture',
queue_name =>'FaeterBR_src_queue',
include_dml =>true,
include_ddl =>true,
include_tagged_lcr =>false,
source_database => NULL,
inclusion_rule => true);
END;
Step 10. Instantiate the FaeterBR schema at DST. by doing export
import : Can I use now datapump to do that ?
---AT SRC:
exp system/superman file=FaeterBR.dmp log=FaeterBR.log
object_consistent=y owner=FaeterBR
---AT DST:
---Create FaeterBR tablespaces and user:
create tablespace FaeterBR_datafile
'/u02/oracle/oradata/str10/FaeterBR_01.dbf' size 100G;
create tablespace ws_app_idx datafile
'/u02/oracle/oradata/str10/FaeterBR_01.dbf' size 100G;
create user FaeterBR identified by FaeterBR_
default tablespace FaeterBR_
temporary tablespace temp;
grant connect, resource to FaeterBR;
imp system/123db file=FaeterBR_.dmp log=FaeterBR.log fromuser=FaeterBR
touser=FaeterBR streams_instantiation=y
Step 11. Create a propagation job at the source database (SRC).
SQL> BEGIN
DBMS_STREAMS_ADM.ADD_SCHEMA_PROPAGATION_RULES(
schema_name =>'FaeterBR',
streams_name =>'FaeterBR_src_propagation',
source_queue_name =>'stream_admin.FaeterBR_src_queue',
destination_queue_name=>'stream_admin.FaeterBR_dst_queue@dst',
include_dml =>true,
include_ddl =>true,
include_tagged_lcr =>false,
source_database =>'SRC',
inclusion_rule =>true);
END;
Step 12. Create an apply process at the destination database (DST).
SQL> BEGIN
DBMS_STREAMS_ADM.ADD_SCHEMA_RULES(
schema_name =>'FaeterBR',
streams_type =>'apply',
streams_name =>'FaeterBR_Dst_apply',
queue_name =>'FaeterBR_dst_queue',
include_dml =>true,
include_ddl =>true,
include_tagged_lcr =>false,
source_database =>'SRC',
inclusion_rule =>true);
END;
Step 13. Create substitution key columns for äll the tables that
haven't a primary key of the FaeterBR schema on DST
The column combination must provide a unique value for Streams.
SQL> BEGIN
DBMS_APPLY_ADM.SET_KEY_COLUMNS(
object_name =>'FaeterBR.tb2',
column_list =>'id1,names,toys,vendor');
END;
Step 14. Configure conflict resolution at the replication db (DST).
Any easier method applicable the schema?
DECLARE
cols DBMS_UTILITY.NAME_ARRAY;
BEGIN
cols(1) := 'id';
cols(2) := 'names';
cols(3) := 'toys';
cols(4) := 'vendor';
DBMS_APPLY_ADM.SET_UPDATE_CONFLICT_HANDLER(
object_name =>'FaeterBR.tb2',
method_name =>'OVERWRITE',
resolution_column=>'FaeterBR',
column_list =>cols);
END;
Step 15. Enable the capture process on the source database (SRC).
BEGIN
DBMS_CAPTURE_ADM.START_CAPTURE(
capture_name => 'FaeterBR_src_capture');
END;
Step 16. Enable the apply process on the replication database (DST).
BEGIN
DBMS_APPLY_ADM.START_APPLY(
apply_name => 'FaeterBR_DST_apply');
END;
Step 17. Test streams propagation of rows from source (src) to
replication (DST).
AT ORCL:
insert into FaeterBR.tb2 values (
31000, 'BAMSE', 'DR', 'DR Lejetoej');
AT STR10:
connect FaeterBR/FaeterBR
select * from FaeterBR.tb2 where vendor= 'DR Lejetoej';
Any other test that can be made?Check the metalink doc 301431.1 and validate
How To Setup One-Way SCHEMA Level Streams Replication [ID 301431.1]
Oracle Server Enterprise Edition - Version: 10.1.0.2 to 11.1.0.6
Cheers. -
For several months now safari has not been loading web pages properly (not them all, it is a bit random, but maybe every 3rd or 4th page I open?). The blue loading bar gets to about 1.5 inches from the end and stops. I can then click on the bar and refresh and it loads no problems but this is highly inconvenient and I can't seem to fix it.
I have reset safari, updated all software, I am on a mac book pro, I have Version 5.1.5 safari.
Would this be an internet problem rather than a software problem? How would I check.
It's not very convenient when you're doing something important like trying to get tickets for an event and then it jams, and you know you need to refresh but if you refresh you've lost the tickets...
Any suggestions welcomeHi Krisztina ..
Using OpenDNS can help when pages won't load properly.
Use OpenDNS for better speed, more security, includes anti phishing filters, prevents browser redirects, blocks the flashback trojan, and it's free.
Open System Preferences / Preferences then select the Network tab. Click the Advanced tab then click the DNS tab.
Click +
Enter these addresses exactly as you see them here.
208.67.222.222
Click +
208.67.220.220
Then click OK.
Apple suggests using OpenDNS here > Safari 5.0.1 or later: Slow or partial webpage loading, or webpage cannot be found
Maybe you are looking for
-
Iphone 3gs - os 4.0.1 'Updating iPhone Softwar' Freeze
Hi, I'm in the process of updating the software on my iPhone (3GS) to v 4.0.1. plugged it in...all ok. Backed up Iphone...all ok. BUT, now it is just sitting there with the status bar not moving at all. iTunes as an application is fine (when i attemp
-
Hi all, I've been working with Mainstage 2.1.3 and have experienced concerts crashing immediately after loading. In an attempt to solve crash issue, I've installed Mainstage 2.2.2 to see if that helps alleviate the issue. My question is: should I u
-
How to get all Package's names. java.lang.Package[code/] return only few names.
-
Can I add a repeating field in a PDF, one where the end user can select to duplicate a field when filling out a form? Thanks for your help! Jeff
-
Error 5002 while entering code for Peter Pan
I cannot enter the code for my Peter Pan Digital Copy. when I enter it in and click "Redeem", an error code pops up saying I cannot connect to itunes with error code 5002.