Help needed turning LC II into Mac network server

Just picked up 4 LC IIs that I would like to turn into Mac network servers. I would like to adapt the 80 pin blade style SCSI HDs to work with a B&W Rev. A. Need to learn more about hot swappable SCSI arrays.
Comments welcome.
Jim

Jim-
You have asked seven questions at once.
Any Mac running 7.1 or later can share files using Personal File Sharing, without the need for AppleShare server or Mac OS X Server software. This is all most folks need for casual home or light office use. 7.5.3 and later has the easier to use Open Transport networking software, and 9.0 or later can most easily connect with Macs running 10.4 and later.
LC-II have only narrow SCSI-1, and unless they have sprouted a PCI slot, cannot participate in the rest of this discussion.
There are several classes of Wide SCSI busses. The one first implemented in the beige G3 with Server card is a Fast & Wide Single-Ended bus. It used the readily available and really cheap Apple/ATTO PCI PSC card. It is limited to the 3 to 4 feet of 68-pin high-tech-plastic-jacket cable already installed inside the cabinet, and adding any external drives made the cable too long, and the whole thing became unreliable. Many Single-Ended Drives can provide termination with a strap setting.
Historically, HVD (High Voltage Differential) came next, but it was a false start. It is incompatible with everything. Stay away.
The next class of Controllers and Drives used LVD (Low-Voltage Differential) drivers and receivers. These "balanced" or "push-pull" drivers and receivers are much more noise-immune. Speeds increase dramatically and cable length restrictions are (practically speaking) eliminated. Some Internal cables still use the flat high-tech-plastic-jacket cable, but are generally implemented with twist-and-flat cables. To use adjacent drive positions in a Blue & White G3, your cable must have more than 8 inches between connectors, mainly due to the bizarre way the cable must be folded to reach the drive connectors.
A discrete captive terminator at the end of the cable is the norm. Occasionally, a terminator that is plugged into the last connector socket is used instead. All these terminators are generally capable of applying termination for either LVD or Single-Ended cables, and do so automatically. But they are too big to fit on a drive, and therefore almost no LVD-capable drives contain termination circuitry.
Caution: If any drive on the cable is a Single-Ended drive, the entire cable drops back into Single-Ended mode, and previous cable length restrictions and speed limits apply!

Similar Messages

  • Help with CF9 Standard Install and Mac OS Server (Snow Leopard Server)

    Hello,
    I recently purchased a mac mini server (with snow leopard server) and will be using it to host my CF9 applications.  This install is WAY different than the install needed on a windows machine.  I tried to install it once and somehow hosed up Apache and now I can't even get it to start up (apache).  So I am having the colo company to do a full restore of the server and I took notes on the Mac Server install and below is the questions I have.
    1.) Since Snow Leopard Server comes with Apache webserver, it is what CF wants to use.  This is fine, I just need to know where these things are...
    It is asking for the Configuration Directory:  I'm guessing it is /private/etc/apache2 ? Right or Wrong???
    2.) It is asking for Directory and file name of server binary:  It currently defaults to /usr/sbin/httpd  is this right or should I point it to another directory?
    3.) It is asking for Directory and file name of server script: It currently defaults to /usr/sbin/apachectl  is this right or should I point it to another directory?
    It also wants the location where I can place the CFIDE.  Can I place this anywhere I wish or is there a preferred location to point this to?
    and finally, I have CF9 Standard, so on the mac server should I install it as a server configuration (self contained instance) or Enterprise Multiserver config.  I was reading online that its better to install as an Enterprise Multiserver setup, but I don't know if this will work for me since I'm useing the standard edition.
    Please Help ANYONE, if you have mac os experience and installing CF9 onto a mac server
    Thanks

    I have been getting this exact same problem.  CF installer is somehow writing some invalid information into the httpd.conf file.  I was able to replace the httpd.conf file with the default one, and was able to go through the webconnector process again and (sometimes randomly) it works.  I also spent about 4 hours on the line with adobe CF support and made no progress beyond what I'll post here .
    To answer your questions about file locations:
    /private/etc/apache2/ for the httpd.conf files
    /usr/sbin/ for both the apachectl and the httpd binaries
    Although I'm able to get past where you are, and it seems to work correctly, Immediately upon adding a new site via server admin it all breaks.  Coldfusion then will only work if I manually go to a cfm document.  For example:  http://example.com/ will give me the raw text from the (default index) index.cfm file.  But typing http://example.com/index.cfm works.
    I am lost here as well.  After 4 hours on the phone with adobe support I would have hoped it would be an easy fix.  I've completely nuked and reinstalled the server from scratch with the exact same results both times.
    Does anyone have the slightest clue about what may be going on here?

  • Need help with turning multiple rows into a single row

    Hello.
    I've come across a situation that is somewhat beyond my knowledge base. I could use a little help with figuring this out.
    My situation:
    I am attempting to do some reporting from a JIRA database. What I am doing is getting the dates and times for specific step points of a ticket. This is resulting in many rows per ticket. What I need to do is return one row per ticket with a calculation of time between each step. But one issue is that if a ticket is re-opened, I want to ignore all data beyond the first close date. Also, not all tickets are in a closed state. I am attaching code and a sample list of the results. If I am not quite clear, please ask for information and I will attempt to provide more. The database is 10.2.0.4
    select jiraissue.id, pkey, reporter, summary
    ,changegroup.created change_dt
    ,dbms_lob.substr(changeitem.newstring,15,1) change_type
    ,row_number() OVER ( PARTITION BY jiraissue.id ORDER BY changegroup.created ASC ) AS order_row
    from jiraissue
    ,changeitem, changegroup
    ,(select * from customfieldvalue where customfield = 10591 and stringvalue = 'Support') phaseinfo
    where jiraissue.project = 10110
    and jiraissue.issuetype = 51
    and dbms_lob.substr(changeitem.newstring,15,1) in ('Blocked','Closed','Testing','Open')
    and phaseinfo.issue = jiraissue.id
    and changeitem.groupid = changegroup.id
    and changegroup.issueid = jiraissue.id
    order by jiraissue.id,change_dt
    Results:
    1     21191     QCS-91     Error running the Earliest-deadlines flight interface request/response message     2008-07-16 9:30:38 AM     Open     1
    2     21191     QCS-91     Error running the Earliest-deadlines flight interface request/response message     2008-07-16 11:37:02 AM     Testing     2
    3     21191     QCS-91     Error running the Earliest-deadlines flight interface request/response message     2010-06-08 9:14:52 AM     Closed     3
    4     21191     QCS-91     Error running the Earliest-deadlines flight interface request/response message     2010-09-02 11:29:37 AM     Open     4
    5     21191     QCS-91     Error running the Earliest-deadlines flight interface request/response message     2010-09-02 11:29:42 AM     Open     5
    6     21191     QCS-91     Error running the Earliest-deadlines flight interface request/response message     2010-09-02 11:29:50 AM     Testing     6
    7     21191     QCS-91     Error running the Earliest-deadlines flight interface request/response message     2010-09-02 11:29:53 AM     Closed     7
    8     23234     QCS-208     System Baseline - OK button does not show up in the Defer Faults page for the System Engineer role      2008-10-03 10:26:21 AM     Open     1
    9     23234     QCS-208     System Baseline - OK button does not show up in the Defer Faults page for the System Engineer role      2008-11-17 9:39:39 AM     Testing     2
    10     23234     QCS-208     System Baseline - OK button does not show up in the Defer Faults page for the System Engineer role      2011-02-02 6:18:02 AM     Closed     3
    11     23977     QCS-311     Tally Sheet - Reason Not Done fails to provide reason for unassigned tasks     2008-09-29 2:44:54 PM     Open     1
    12     23977     QCS-311     Tally Sheet - Reason Not Done fails to provide reason for unassigned tasks     2010-05-29 4:47:37 PM     Blocked     2
    13     23977     QCS-311     Tally Sheet - Reason Not Done fails to provide reason for unassigned tasks     2011-02-02 6:14:57 AM     Open     3
    14     23977     QCS-311     Tally Sheet - Reason Not Done fails to provide reason for unassigned tasks     2011-02-02 6:15:32 AM     Testing     4
    15     23977     QCS-311     Tally Sheet - Reason Not Done fails to provide reason for unassigned tasks     2011-02-02 6:15:47 AM     Closed     5

    Hi,
    Welcome to the forum!
    StblJmpr wrote:
    ... I am attempting to do some reporting from a JIRA database. What is a JIRA database?
    I am attaching code and a sample list of the results. If I am not quite clear, please ask for information and I will attempt to provide more. Whenever you have a question, please post a little sample data (CREATE TABLE and INSERT statements, relevant columns only) for all tables involved, and the results you want from that data.
    Simplify the problem as much as possible. For example, if the part you don't know how to do only involves 2 tables, then jsut post a question involving those 2 tables. So you might just post this much data:
    CREATE TABLE     changegroup
    (      issueid          NUMBER
    ,      created          DATE
    ,      id          NUMBER
    INSERT INTO changegroup (issueid, created, id) VALUES (21191,  TO_DATE ('2008-07-16 09:30:38 AM', 'YYYY-MM-DD HH:MI:SS AM'),  10);
    INSERT INTO changegroup (issueid, created, id) VALUES (21191,  TO_DATE ('2008-07-16 11:37:02 AM', 'YYYY-MM-DD HH:MI:SS AM'),  20);
    INSERT INTO changegroup (issueid, created, id) VALUES (21191,  TO_DATE ('2010-06-08 09:14:52 AM', 'YYYY-MM-DD HH:MI:SS AM'),  90);
    INSERT INTO changegroup (issueid, created, id) VALUES (21191,  TO_DATE ('2010-09-02 11:29:37 AM', 'YYYY-MM-DD HH:MI:SS AM'),  10);
    INSERT INTO changegroup (issueid, created, id) VALUES (21191,  TO_DATE ('2010-09-02 11:29:42 AM', 'YYYY-MM-DD HH:MI:SS AM'),  10);
    INSERT INTO changegroup (issueid, created, id) VALUES (21191,  TO_DATE ('2010-09-02 11:29:50 AM', 'YYYY-MM-DD HH:MI:SS AM'),  20);
    INSERT INTO changegroup (issueid, created, id) VALUES (21191,  TO_DATE ('2010-09-02 11:29:53 AM', 'YYYY-MM-DD HH:MI:SS AM'),  90);
    INSERT INTO changegroup (issueid, created, id) VALUES (23234,  TO_DATE ('2008-10-03 10:26:21 AM', 'YYYY-MM-DD HH:MI:SS AM'),  10);
    INSERT INTO changegroup (issueid, created, id) VALUES (23234,  TO_DATE ('2008-11-17 09:39:39 AM', 'YYYY-MM-DD HH:MI:SS AM'),  20);
    INSERT INTO changegroup (issueid, created, id) VALUES (23234,  TO_DATE ('2011-02-02 06:18:02 AM', 'YYYY-MM-DD HH:MI:SS AM'),  90);
    INSERT INTO changegroup (issueid, created, id) VALUES (23977,  TO_DATE ('2008-09-29 02:44:54 PM', 'YYYY-MM-DD HH:MI:SS AM'),  10);
    INSERT INTO changegroup (issueid, created, id) VALUES (23977,  TO_DATE ('2010-05-29 04:47:37 PM', 'YYYY-MM-DD HH:MI:SS AM'),  30);
    INSERT INTO changegroup (issueid, created, id) VALUES (23977,  TO_DATE ('2011-02-02 06:14:57 AM', 'YYYY-MM-DD HH:MI:SS AM'),  10);
    INSERT INTO changegroup (issueid, created, id) VALUES (23977,  TO_DATE ('2011-02-02 06:15:32 AM', 'YYYY-MM-DD HH:MI:SS AM'),  20);
    INSERT INTO changegroup (issueid, created, id) VALUES (23977,  TO_DATE ('2011-02-02 06:15:47 AM', 'YYYY-MM-DD HH:MI:SS AM'),  90);
    CREATE TABLE     changeitem
    (      groupid          NUMBER
    ,      newstring     VARCHAR2 (10)
    INSERT INTO changeitem (groupid, newstring) VALUES (10, 'Open');
    INSERT INTO changeitem (groupid, newstring) VALUES (20, 'Testing');
    INSERT INTO changeitem (groupid, newstring) VALUES (30, 'Blocked');
    INSERT INTO changeitem (groupid, newstring) VALUES (90, 'Closed');Then post the results you want to get from that data, like this:
    ISSUEID HISTORY
      21191 Open (0) >> Testing (692) >> Closed
      23234 Open (45) >> Testing (807) >> Closed
      23977 Open (607) >> Blocked (249) >> Open (0) >> Testing (0) >> ClosedExplain how you get those results from that data. For example:
    "The output contains one row per issueid. The HISTORY coloumn shows the different states that the issue went through, in order by created, starting with the earliest one and continuing up until the first 'Closed' state, if there is one. Take the first row, issueid=21191, for example. It started as 'Open' on July 16, 2008, then, on the same day (that is, 0 days later) changed to 'Testing', and then, on June 8, 2010, (692 days later), it became 'Closed'. That same issue opened again later, on September 2, 2010, but I don't want to see any activity after the first 'Closed'."
    The database is 10.2.0.4That's very important. Always post your version, like you did.
    Here's one way to get those results from that data:
    WITH     got_order_row     AS
         SELECT     cg.issueid
         ,     LEAD (cg.created) OVER ( PARTITION BY  cg.issueid
                                          ORDER BY      cg.created
                  - cg.created            AS days_in_stage
         ,       ROW_NUMBER ()     OVER ( PARTITION BY  cg.issueid
                                          ORDER BY      cg.created
                               )    AS order_row
         ,     ci.newstring                     AS change_type
         FROM    changegroup     cg
         JOIN     changeitem     ci  ON   cg.id     = ci.groupid
         WHERE     ci.newstring     IN ( 'Blocked'
                           , 'Closed'
                           , 'Testing'
                           , 'Open'
    --     AND     ...          -- any other filtering goes here
    SELECT       issueid
    ,       SUBSTR ( SYS_CONNECT_BY_PATH ( change_type || CASE
                                                             WHEN  CONNECT_BY_ISLEAF = 0
                                           THEN  ' ('
                                              || ROUND (days_in_stage)
                                              || ')'
                                                         END
                                    , ' >> '
               , 5
               )     AS history
    FROM       got_order_row
    WHERE       CONNECT_BY_ISLEAF     = 1
    START WITH     order_row          = 1
    CONNECT BY     order_row          = PRIOR order_row + 1
         AND     issueid               = PRIOR issueid
         AND     PRIOR change_type     != 'Closed'
    ORDER BY  issueid
    ;Combining data from several rows into one big delimited VARCHAR2 column on one row is call String Aggregation .
    I hope this answers your question, but I guessed at so many things, I won't be surprised if it doesn't. If that's the case, point out where this is wrong, post what the results should be in those places, and explain how you get those results. Post new data, if necessary.

  • Advice/Help needed migrating/working with two macs

    I currently own a mid-2010 (I think) Macbook Pro and a couple of months ago I bought a Mac Mini. Unfortunately when I set up the Mac Mini I was short on time and my excitement/lack of patience got the better of me so I copied everything on the HDD from my MBP over to the Mac Mini and I have been using the same profile to login on both machines.
    This causes a few problems, particularly when I'm trying to connect the two machines via a network to share files. They can never connect, I'm thinking probably because they're using the same profile and get confused. I also haven't taken the time to properly install all the applications and so some do not work on the mini.
    Rather than trying to pull my hair out trying to solve the issues, I think I've reached a point where I think I need to either start over or get some advice on what to do.
    Ideally I'd like to use the Mini mainly for music apps (Garageband, possibly Logic Pro X in the future) and occassional internet and iTunes use. Since it has a bigger HDD, I'd like to store my music on the Mini.
    I would then use the MBP as my general internet and iTunes machine. I would however like to be able to use it for music production stuff (again GB and/or Logic) if I am travelling. I know that I will need to upgrade the OS and the RAM which I am happy to do.
    I would like to be able to have most of the same apps on both machines and also be able to easily transfer files, music etc. between the two.
    So in light of what I'd like to achieve, what would be my best course of action? Would I be best to start over and try to migrate from fresh or can I make something work with what I have?
    A further complication is that I have since used both machines so I will have some new stuff saved on both machines that won't be on the other. Is there any way to keep these new files if I start over?
    Would anyone be gracious enough to point me in the direction of an easy to follow guide to help me achieve what I want?
    Sorry for the long-winded post (and if I've posted in the wrong section) but I really think I lept into the migration without really knowing what I was doing and I could really use some advice to help me work out what to do!

    With your project open, press Shift + Q to open System Settings.
    Where are your render files being stored to? The path should be pointing to your external. I'm betting that it's set to your system drive instead.

  • Help needed to put requirements into uml format

    Hi
    I have got into the bad habit of reading the specification and going
    straight into coding without doing any analysis or design, but all thats about to change! i have been reading some uml tutorials, but none seem relevant to the project i have at the moment, could anyone tell me whether i need to do uml use cases etc for it as it seems quite basic.
    all i am doing is sending rmi messages between applications using different scenarios, ie across a network, on the same network etc etc, then i just get the system start time and stop time after ive sent 1000 messages and thats my result. uml wise, i obviously need an actor for the enginner running the programme, cant think of any more actors unless im missing something? then i need a use case of the messages being sent. do i need one for each scenario? h
    help would be gratefully received
    ness

    If Use Cases don't make a lot of sense to you, don't feel that you have to use them. There's no point generating meaningless documentation that neither you nor anybody else is ever going to read...
    The main point of Use Cases (IMHO) is in requirements elicitation. The diagrams look nice and simple, so you can show them to the client, and make them feel smart.
    Actors are entities that are external to the system or sub-system being modelled. So an Actor could be a user, another computer system, or an external event (e.g. a particular date and time). Actors initiate interactions, so anytime you have a particular function (Use Case) that is triggered by an event, you should ask yourself where the trigger comes from.
    Don't forget to add extra textual information to Use Case diagrams. I include information such as:
    Iteration
    Summary
    Course of events
    Alternative paths
    Exception paths
    Extension points
    Triggers
    Assumptions
    Preconditions
    Postconditions
    Any business rules
    Author and Date for any modifications to the Use Case
    Needless to say, this is a lot of information, almost none of which is conveyed by the diagram itself. You may be better off creating a simple list of functions and filling in the above information for each, or maybe the Use Case diagrams will help you think about what the functions and interactions actually are.
    Good luck.

  • Help! Turning a PDF into an Online Document

    Hello Community,
    I spend a lot of my time taking PDF versions of large chart books, hyperlinking and bookmarking to the nth degree, and writing commentary on these charts. The PDF's can be anywhere from 15 to 500 pages long (sometimes longer) and they range in file size from a couple mbs to sometimes 40-50mbs.
    For larger PDF's that I can't email, I will start using a service like AdobeSend which will be very helpful.
    What I really want to do however is somehow get my PDF's online in a webpage kind of a format. Is something that a layman can do or do I need a degree in website design or programming or something.
    The ideal world would be where the cover of the PDF would be like the home page of a website. Each link or bookmark in the document would function like hypertext in a website. That way, I wouldn't need to send the file at all, it would just be hosted somewhere and whoever had the webaddress could access the online PDF.
    I've looked at website creation sites like Wix, but I didn't see initially how I can host a large PDF document using their site builder. If anyone knows of a good way to turn a linked PDF into a Website like document I would be forever grateful.
    thank you

    Is the PDF embedded?
    Is the color used on a vector object?
    If so you can copy the Pantone color from one object to another with the color picker.
    You can't read the color in the color picker window. You can't pick up any exact color (let alone a spot color) from linked files.

  • Help needed to run a power Mac ap on Intel Mac.

    Hi, I have a Davis Vantage Pro weather station that ran happily on my old Quicksilver Power Mac. Now I have upgraded to a Mac pro machine running Tiger, the 'Weatherlink' software won't work. Davis, a main player in scientific technologies have not upgraded their Mac software (unbelievably!)
    Will Rosetta help here? .... or do I need to get a P.C?
    Hope someone can advise.
    Thanks
    Lunasa

    PPC apps run transparently on Intel Macs, however, in your case it may be a matter of incompatibility. The software is simply not compatible with the current versions of OS X. This has nothing to do with Rosetta. You would have the same problem on your QuickSilver were you to upgrade to Tiger.
    If you transferred the software using Migration Assistant, then try reinstalling the software on the Intel Mac (but first be sure you fully uninstall the transferred app.)

  • Help needed to load XML into DB table

    I need some serious help if someone can spare the time. I am completely new to XML and don't really understand it yet but I need to be able to load an XML file (example) below.
    I want to load this into a table that would look like the following:
    CHAPTER_TITLE    DOC_HTML    DOC_TITLE
    Men's Health      494440          AAAAA
    Men's Health      496812          BBBBB
    etc....
    <?xml version=1.0 encoding=utf-8?>
    <BookCollections Quantity=1 Title=Emis Books Collection>
        <Book Folder=PILSS Title=Patient Support>
            <Chapter Title=Men''s Health>
                <Document DocHTML=494440 Title=AAAAA />
                <Document DocHTML=496812 Title=BBBBB />
                <Document DocHTML=498923 Title=CCCCC />
                <Document DocHTML=499844 Title=DDDDD />
                <Document DocHTML=499901 Title=EEEEE />
            </Chapter>
        </Book>
    </BookCollections>I have read through the documentation I could find but I can't get it to work. I had a simple procedure which loaded the text file as a CLOB and then inserted it into an XMLTYPE column but even that wouldn't work. I would rather it loaded as above in seperate columns.
    Is there a simple example someone can help me out with?

    That is very close ORA_SID thank you. But I get the ORA-19025 error when I have more than one Chapter section. The example was a cut down version, ther real file has thousands of Chapters.
    e.g.
      1  insert into test2 values(xmltype(' <BookCollections Quantity="1" Title="Emis Books Collection">
      2  <Book Folder="PILSS" Title="Patient Support">
      3  <Chapter Title="Men''s Health">
      4              <Document DocHTML="494440" Title="AAAAA" />
      5              <Document DocHTML="496812" Title="BBBBB" />
      6              <Document DocHTML="498923" Title="CCCCC" />
      7              <Document DocHTML="499844" Title="DDDDD" />
      8              <Document DocHTML="499901" Title="EEEEE" />
      9              <Document DocHTML="500381" Title="FFFFF" />
    10              <Document DocHTML="500446" Title="GGGGG" />
    11              <Document DocHTML="500996" Title="HHHHH" />
    12          </Chapter>
    13          <Chapter Title="Contraception">
    14              <Document DocHTML="496815" Title="IIIII" />
    15              <Document DocHTML="496817" Title="JJJJJ" />
    16              <Document DocHTML="499547" Title="KKKKK" />
    17              <Document DocHTML="499550" Title="LLLLL" />
    18              <Document DocHTML="500473" Title="MMMMM" />
    19              <Document DocHTML="500704" Title="NNNNN" />
    20              <Document DocHTML="500813" Title="OOOOO" />
    21              <Document DocHTML="500995" Title="PPPPP />
    22              <Document DocHTML="500996" Title="QQQQQ" />
    23          </Chapter>
    24  </Book>
    25  </BookCollections>
    26* '))
    SQL> /
    1 row created.
    SQL> SELECT extractValue(xml_data, '/BookCollections/Book/Chapter/@Title') AS Chapter_Title,
      2  extractValue(value(em), '/Document/@DocHTML') AS Document_DocHTML,
      3  extractValue(value(em), '/Document/@Title') AS Document_Title
      4  FROM test2,table(XMLSequence(extract(xml_data,'/BookCollections/Book/Chapter/Document'))) em
      5  ;
    FROM test2,table(XMLSequence(extract(xml_data,'/BookCollections/Book/Chapter/Document'))) em
    ERROR at line 4:
    ORA-19025: EXTRACTVALUE returns value of only one nodeCan you help on this?

  • Need help--cannot import hotel.dmp into chinese characterset server

    I'm from china.Because my oracle8i use
    chinese characterset, so I cannot import
    this file into my oracle.
    Has anybody can help me?
    Thanks you very much!!

    I seem to recall that SQL*Loader was capable of doing these kinds of language translations for you. You needed to account for machine language, character set, and datatype all of which could be manipulated either via FTP parameters when a file was transferred (tell ftp not to convert between machine languages, tell sqlloader the machine language being used, tell it the character set, etc.) I found examples of this by scouring the internet for sqlloader examples, but unfortunately I no long have then handy.
    Good luck.
    <BLOCKQUOTE><font size="1" face="Verdana, Arial">quote:</font><HR>Originally posted by potian:
    I'm from china.Because my oracle8i use
    chinese characterset, so I cannot import
    this file into my oracle.
    Has anybody can help me?
    Thanks you very much!!<HR></BLOCKQUOTE>
    null

  • Help needed with a PS script for network share documentation

    I found a nice PS script that will do what I want, however the output portion seems to be broken. It will output the permissions and details, but not list what share it is referring to... Can anyone help with this?
    Thanks!
    https://gallery.technet.microsoft.com/scriptcenter/List-Share-Permissions-83f8c419#content
    <# 
               .SYNOPSIS  
               This script will list all shares on a computer, and list all the share permissions for each share. 
               .DESCRIPTION 
               The script will take a list all shares on a local or remote computer. 
               .PARAMETER Computer 
               Specifies the computer or array of computers to process 
               .INPUTS 
               Get-SharePermissions accepts pipeline of computer name(s) 
               .OUTPUTS 
               Produces an array object for each share found. 
               .EXAMPLE 
               C:\PS> .\Get-SharePermissions # Operates against local computer. 
               .EXAMPLE 
               C:\PS> 'computerName' | .\Get-SharePermissions 
               .EXAMPLE 
               C:\PS> Get-Content 'computerlist.txt' | .\Get-SharePermissions | Out-File 'SharePermissions.txt' 
               .EXAMPLE 
               Get-Help .\Get-SharePermissions -Full 
    #> 
    # Written by BigTeddy November 15, 2011 
    # Last updated 9 September 2012  
    # Ver. 2.0  
    # Thanks to Michal Gajda for input with the ACE handling. 
    [cmdletbinding()] 
    param([Parameter(ValueFromPipeline=$True, 
        ValueFromPipelineByPropertyName=$True)]$Computer = '.')  
    $shares = gwmi -Class win32_share -ComputerName $computer | select -ExpandProperty Name  
    foreach ($share in $shares) {  
        $acl = $null  
        Write-Host $share -ForegroundColor Green  
        Write-Host $('-' * $share.Length) -ForegroundColor Green  
        $objShareSec = Get-WMIObject -Class Win32_LogicalShareSecuritySetting -Filter "name='$Share'"  -ComputerName $computer 
        try {  
            $SD = $objShareSec.GetSecurityDescriptor().Descriptor    
            foreach($ace in $SD.DACL){   
                $UserName = $ace.Trustee.Name      
                If ($ace.Trustee.Domain -ne $Null) {$UserName = "$($ace.Trustee.Domain)\$UserName"}    
                If ($ace.Trustee.Name -eq $Null) {$UserName = $ace.Trustee.SIDString }      
                [Array]$ACL += New-Object Security.AccessControl.FileSystemAccessRule($UserName, $ace.AccessMask, $ace.AceType)  
                } #end foreach ACE            
            } # end try  
        catch  
            { Write-Host "Unable to obtain permissions for $share" }  
        $ACL  
        Write-Host $('=' * 50)  
        } # end foreach $share
    This is what the output looks like when ran with 'RemoteServer' | .\Get-SharePermissions.ps1 | Out-File 'sharepermissions.xls'
    FileSystemRights  : Modify, Synchronize
    AccessControlType : Allow
    IdentityReference : Everyone
    IsInherited       : False
    InheritanceFlags  : None
    PropagationFlags  : None

    Actually it is not being written only with Write-Host.  The last line of the loop is this "$ACL"  which ius an array of objects. 
    Here is a version that gets the info more easily and produces flexible objects.  It should be easier to modify into what is needed.
    # Get-ShareSec.ps1
    [cmdletbinding()]
    param(
    [Alias('ComputerName')]
    [Parameter(
    ValueFromPipelineByPropertyName=$True
    )]$Name=$env:COMPUTERNAME
    Process {
    Write-Verbose "Computer=$name"
    $shares =Get-WMiObject Win32_Share -ComputerName $name -Filter 'Type=0' -ea 0
    foreach($share in $shares){
    $sharename=$share.Name
    Write-Verbose "`tShareName=$sharename"
    $ShareSec = Get-WMIObject -Class Win32_LogicalShareSecuritySetting -Filter "name='$ShareName'" -ComputerName $name
    try {
    foreach ($ace in $ShareSec.GetSecurityDescriptor().Descriptor.DACL) {
    $props=[ordered]@{
    ComputerName=$name
    ShareName=$sharename
    TrusteeName=$ace.Trustee.Name
    TrusteeDomain=$ace.Trustee.Domain
    TrusteeSID=$ace.Trustee.SIDString
    New-Object PsObject -Property $props
    catch {
    Write-Warning ('{0} | {1} | {2}' -f $Computer,$sharename, $_)
    Get-Adcomputer -Filter * | .\Get-ShareSec.ps1 -v
    ¯\_(ツ)_/¯

  • Please - immediate help needed parsing csv values into multiple rows

    Hello, we have a very immediate need to be able to parse out a field of comma separated values into individual rows. The following is an example written in SQL Server syntax which does not work in Oracle.
    The tricky part is that each ROUTES can be a different length, and each CSV can have a different number of routes in it.
    Here is an example of the table ("Quotes") of CSV values I want to normalize:
    TPNUMBER ROUTES
    1001 1, 56W, 18
    1002 2, 16, 186, 28
    Here is an example of what I need it to look like:
    TPNUMBER ROUTES
    1001 1
    1001 56W
    1001 18
    1002 2
    1002 16
    1002 186
    1002 28
    Here is the "Tally" table for the query below:
    ID
    1
    2
    3
    4
    5
    6
    7
    And finally, here is the query which parses CSV values into multiple rows but which does not work in Oralce:
    SELECT TPNUMBER,
    NullIf(SubString(',' + ROUTES + ',' , ID , CharIndex(',' , ',' + ROUTES + ',' , ID) - ID) , '') AS ONEROUTE
    FROM Tally, Quotes
    WHERE ID <= Len(',' + ROUTES + ',') AND SubString(',' + Phrase + ',' , ID - 1, 1) = ','
    AND CharIndex(',' , ',' + ROUTES + ',' , ID) - ID > 0
    It may be necessary to use a cursor to loop through the CSV table and process each row (a loop within another loop...) but this is beyond my comprehesion of PL/SQL.
    Many thanks in advance for your advice/help.
    apk

    Not sure what you are trying to do with the last step, but this should work for the first part. I assume you would use sqlldr but I just did inserts instead. You might need more than 5 "routes" in the csv. You could put some reasonable max on that number of columns:
    SQL>create table t_csv
    2 (TPNUMBER varchar2(20),
    3 ROUTE_1 VARCHAR2(5),
    4 ROUTE_2 VARCHAR2(5),
    5 ROUTE_3 VARCHAR2(5),
    6 ROUTE_4 VARCHAR2(5),
    7 ROUTE_5 VARCHAR2(5),
    8 ROUTE_6 VARCHAR2(5) );
    Table created.
    SQL>INSERT INTO t_csv (TPNUMBER,ROUTE_1,ROUTE_2) values( '1001 1', '56W', '18' );
    1 row created.
    SQL>INSERT INTO t_csv (TPNUMBER,ROUTE_1,ROUTE_2,ROUTE_3) values( '1002 2', '16', '186', '28');
    1 row created.
    SQL>create table t_quotes(
    2 tpnumber NUMBER,
    3 routes VARCHAR2(5));
    Table created.
    SQL>DECLARE
    2 L_tpnumber NUMBER;
    3 L_route VARCHAR2(5);
    4 begin
    5 for rec in (select * from t_csv) loop
    6 L_tpnumber := SUBSTR(rec.tpnumber,1,INSTR(rec.tpnumber,' ')-1);
    7 L_route := SUBSTR(rec.tpnumber,INSTR(rec.tpnumber,' ')+1);
    8 insert into t_quotes values( L_tpnumber, l_route );
    9 if rec.route_1 is not null then
    10 insert into t_quotes values( L_tpnumber, rec.route_1 );
    11 end if;
    12 if rec.route_2 is not null then
    13 insert into t_quotes values( L_tpnumber, rec.route_2 );
    14 end if;
    15 if rec.route_3 is not null then
    16 insert into t_quotes values( L_tpnumber, rec.route_3 );
    17 end if;
    18 if rec.route_4 is not null then
    19 insert into t_quotes values( L_tpnumber, rec.route_4 );
    20 end if;
    21 if rec.route_5 is not null then
    22 insert into t_quotes values( L_tpnumber, rec.route_5 );
    23 end if;
    24 end loop;
    25 end;
    26 /
    PL/SQL procedure successfully completed.
    SQL> select tpnumber, routes from t_quotes;
    TPNUMBER ROUTE
    1001 1
    1001 56W
    1001 18
    1002 2
    1002 16
    1002 186
    1002 28
    7 rows selected.

  • Help need to set up Printing to network printer

    I am trying to set up a printing via a print server attached to my home network. I know the print server works as I can print to it via Linux. How do I set this up please? the print server is an LG N1A1 NAS & the printer is a brother DPC 115 C

    What happened when you created the connection? Did you upload
    the
    connection file to the server? Is your testing server local
    IIS?
    Nancy Gill
    Adobe Community Expert
    Author: Dreamweaver 8 e-book for the DMX Zone
    Co-Author: Dreamweaver MX: Instant Troubleshooter (August,
    2003)
    Technical Editor: Dreamweaver CS3: The Missing Manual,
    DMX 2004: The Complete Reference, DMX 2004: A Beginner's
    Guide
    Mastering Macromedia Contribute
    Technical Reviewer: Dynamic Dreamweaver MX/DMX: Advanced PHP
    Web Development
    "Johnny Polite" <[email protected]> wrote in
    message
    news:funopc$luq$[email protected]..
    > Hello,
    >
    > I am just starting to learn ASP with VBScript because I
    am trying to
    > develop
    > an online registration application to connect to a
    Access DB that I
    > previously
    > built. I am just reading through books and enjoying the
    learning process.
    > I
    > am pretty decent at VBA, so it is fun to apply that to
    the internet.
    >
    > My big problem is that I receive this error message on
    the browser: Data
    > source name not found and no default driver specified. I
    set up the DSN
    > on the
    > System tab in Administrative tools in the Control Panel.
    I have my sample
    > DB
    > placed on a server that recognizes ASP commands.
    Dreamweaver recognizes
    > the
    > connection and I can manipulate the recordsets,
    establish SQL
    > statements...but
    > when I get to the browser, it gives me the error
    message.
    >
    > I have been learning both in FrontPage and in
    Dreamweaver and Front Page
    > can
    > connect just fine to the DB through it's internal menus.
    I much prefer
    > Dreamweaver, though, and I know that when I get this
    connectivity issue
    > straightened out I will start really making some
    progress.
    >
    > I appreciate all the help in advance and if you need me
    to clarify
    > anything,
    > let me know.
    >

  • Urgent help needed in inserting data into a custom table in oracle WorkFlow

    Hi
    I am trying to get data from the WF and insert into a custom table..
    I read that workflow procedures WONT allow commits...
    Oracle Workflow will not support autonomous commits in any procedure it calls directly. If you need to perform commits, then embed your SQL in a subprocedure and declare it as an autonomous block. This subprocedure must be capable of being rerun. Additionally, note that Oracle Workflow handles errors by rolling back the entire procedure and setting its status to ERROR. Database updates performed by autonomous commits cannot be rolled back, so you will need to write your own compensatory logic for error handling
    Have anyone did this..
    Please give me some idea ...It is urgent
    I am getting data using getitemattribute..and try to insert it into a custom table
    thanks
    kp

    Pl do not post duplicate threads - insert dont work in Workflow
    Srini

  • Help needed in 'Using iTunes for Mac' Forum

    Help please!
    I seem to be going round in circles trying to help someone and don't have access to the Lounge to issue a request for help with this thread:
    http://discussions.apple.com/thread.jspa?messageID=3624439#3624439
    Any knowledgeable iTunes users are welcome to post a second opinion.
    Thank you,
    Colin R.

    I will send up an alert for you, Colin. Even though I use iTunes for Mac, troubleshooting it isn't my forté.

  • Help needed in using Facetime over cellular network on Ipad2 3G IOS6

    i updated my Ipad2 3G to IOS6, as they mentioned that i will be able to use facetime over cellular network,
    however everytime i try it over the network, it says i must connect through Wifi. any help!!

    Facetime over 3G is currently only available on the iPad 3, not the iPad 2 - from http://www.apple.com/ios/whats-new/ :
    3. FaceTime video calling requires a FaceTime-enabled device for the caller and recipient and a Wi-Fi connection. FaceTime over a cellular network requires iPhone 4S, iPhone 5, or iPad (3rd generation) with cellular data capability.

Maybe you are looking for