Help or ideas how to configure two cisco 1230 ap-s acting like bridges
Hello ya´ll
Need help with configuration of two cisco 1230 ap-s, which are acting as bridges today. Idea is to configure an 4506 (EIGRP) with two new VLAN-s, "hide" those in 2 VRF-s and send those thru one of the ap-s via radio link (a). Distance between is about 700 feet. On the other side an 3560 is acting as L3 device so VRF is needed on 3560 to. Post your thoughts and ideas. Thank´s in advance.
Hi Bernard,
If you have WCS, you can use templates to synchronize your configurations on the WLCs.
Another possibility is you can upload your current configuration from your production WLC, and then open up the configuration file and edit the IP addresses to give new addresses to the new WLC. You will also want to change the system name to be unique as well. You can then download this config onto the new WLC, as long as the IP addresses and system name are different it should not interfere with your current WLC.
To have the WLCs operate together properly, you will want to make sure they are defined in a mobility group, see the following for instructions:
http://www.cisco.com/en/US/docs/wireless/controller/7.0/configuration/guide/c70mobil.html
-Patrick Croak
Wireless TAC
Similar Messages
-
How to configure two Cisco WLC-5508-50
Hi everyone, last year we buy 1 wlc-5508-50 to use with cisco 1142 AP. This year we plan to add more APs and we just buy another WLC-5508-50 because it was cheaper than to buy 50 licences. We would like to know what is the best way to configure our second WLC so that we can distribute our 75 APs on each controller. Maybe someone can help us. Thanks!
Hi Bernard,
If you have WCS, you can use templates to synchronize your configurations on the WLCs.
Another possibility is you can upload your current configuration from your production WLC, and then open up the configuration file and edit the IP addresses to give new addresses to the new WLC. You will also want to change the system name to be unique as well. You can then download this config onto the new WLC, as long as the IP addresses and system name are different it should not interfere with your current WLC.
To have the WLCs operate together properly, you will want to make sure they are defined in a mobility group, see the following for instructions:
http://www.cisco.com/en/US/docs/wireless/controller/7.0/configuration/guide/c70mobil.html
-Patrick Croak
Wireless TAC -
I have Calendar alerts on every device [Mac/iPad/iPhone] after installing Mountain Lion. How do I stop this? Tech support acted like I was the first person this happened to. Anyone have the solution?
Well, whichever device you uncheck = exclude from calendars (and reminders) via iCloud will be excluded as both, receiver and sender. It's an "all or nothing", I guess. Otherwise it'd get more complicated, and the support calls could easily fill an extra forum...
@lmp68: don't think iTunes is it, in the days of iCloud that would sure take quite an extra effort, if possible at all. -
How to configure a Cisco 3560 with MAC-based 802.1x authentication by radius server
Hi dearI
How can I configure a Cisco 3560 to authenticate a client based on its mac address with 802.1x and radius server. Many tanks in advance!Olivier,
You can't reference WLP visitor roles in weblogic.xml, but you can
reference global roles (created using the WLS console):
- <security-role-assignment>
<role-name>PortalSystemAdministrator</role-name>
<externally-defined />
</security-role-assignment>
-Phil
"Olivier" <[email protected]> wrote in message
news:[email protected]..
>
We need to have login page to our portal app.
When using "form based" authentication is it possible to map the securityon a
"entitlement role" ?
Our need is to be abled to give direct url acces to some pages of theportal (for
exemple by sending urls like"http://server/appcontextpath/appmanager/myportal/mydesktop?_nfpb=true&_page
Label=mypage")"
by email to portal users) and need a simple mecanism of authenticationbefore
redirecting to the portal page.
Inste -
HI, I need to configure a 2960 switch at a client site. They have routers already been installed on site, one is for data traffic another is for voice. I have created two vlans on switch for data and voice. Now I couldn't get any idea what would be the default gateway on switch.
Please give me any suggestions.HI Leo,
Many thanks for your reply.
But there are two up-links going from Gi 0/1 and Gi 0/2. I have configured the S/W like below,
interface GigabitEthernet0/1
description UPLINK TO Data router
switchport access vlan 100
switchport mode access
interface GigabitEthernet0/2
description UPLINK TO voice router
switchport access vlan 100
switchport mode access
interface Vlan1
no ip address
no ip route-cache
shutdown
interface Vlan60
ip address 192.168.1.253 255.255.255.0
ip helper address 192.168.1.1
no ip route-cache
interface Vlan100
ip address 172.16.1.253 255.255.255.0
ip helper address 172.16.1.1
no ip route-cache
I have used IP helper address, but I am getting some connecting issues on PCs and IP phones. Please suggest me, Can I manage it with two uplinks with different IP addresses.
Thanks in advance. -
How to configure two links between switches SG300
Hello!
I have two SG300 serie switches and two Gigabit connection between them. How do I configured these two links to work toghether like a one 2 Gigabit channel?
thanks a lot.Hi Angel,
I think what you are trying to do is called a LAG on the SG300. This option is located under the "Port Management" tab and you can manage which ports you want to be in the LAG under "Link Aggregation" and there you will see "LAG Management" where you can edit your LAG 1 with the 2 ports that needs to act as one 2 Gigabit port.
I hope that was able to help you as that is what I have gathered from your question. Please reply back if you still need more assistance.
Thanks,
Brian Ng -
How to configure wireless Cisco 1041/EAP2 with Radius
Hello,
Having trouble configuring wireless on a Cisco 1041 with a 2012 Radius Server
I have a cisco ASA 5505 and Windows server 2012 Radius with NAP and Network Security policy
Guest Test guest works, test does not, I want the users to log into test with their AD credentials
Here is the AP config:
Thanks for any help
o service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname ap1
logging rate-limit console 9
aaa new-model
aaa group server radius rad_eap
aaa group server radius rad_mac
aaa group server radius rad_acct
aaa group server radius rad_admin
aaa group server tacacs+ tac_admin
aaa group server radius rad_pmip
aaa group server radius dummy
aaa group server radius rad_eap2
server x.x.x.x auth-port 1645 acct-port 1646
aaa authentication login eap_methods group rad_eap
aaa authentication login mac_methods local
aaa authentication login eap_methods2 group rad_eap2
aaa authorization exec default local
aaa accounting network acct_methods start-stop group rad_acct
aaa session-id common
clock timezone -0500 -5
clock summer-time -0400 recurring
ip domain name ser.local
dot11 syslog
dot11 ssid test
vlan 1
authentication open eap eap_methods2
authentication network-eap eap_methods2
authentication key-management wpa
mbssid guest-mode
dot11 ssid test guest
vlan 12
authentication open
authentication key-management wpa
mbssid guest-mode
wpa-psk ascii 7
dot11 priority-map avvid
dot11 phone dot11e
power inline negotiation injector 001b.8fac.990a
power inline negotiation prestandard source
class-map match-all _class_data_policy0
match ip dscp default
class-map match-all _class_voice_policy0
match ip dscp ef
policy-map voice_policy
class _class_voice_policy0
set cos 6
policy-map data_policy
class _class_data_policy0
set cos 0
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 1 mode ciphers aes-ccm
encryption vlan 12 mode ciphers aes-ccm
ssid ihiCorp
ssid ihiGuest
antenna gain 0
mbssid
station-role root
interface Dot11Radio0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
service-policy input data_policy
service-policy output data_policy
interface Dot11Radio0.12
encapsulation dot1Q 12
no ip route-cache
bridge-group 12
bridge-group 12 subscriber-loop-control
bridge-group 12 block-unknown-source
no bridge-group 12 source-learning
no bridge-group 12 unicast-flooding
bridge-group 12 spanning-disabled
service-policy input data_policy
service-policy output data_policy
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
no keepalive
interface GigabitEthernet0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface GigabitEthernet0.12
encapsulation dot1Q 12
no ip route-cache
bridge-group 12
no bridge-group 12 source-learning
bridge-group 12 spanning-disabled
interface BVI1
ip address x.x.x.x 255.255.255.0
no ip route-cache
ip default-gateway x.x.x.x
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
ip radius source-interface BVI1
radius-server attribute 32 include-in-access-req format %h
radius-server host x.x.x.x auth-port 1645 acct-port 1646 key 7
radius-server vsa send accounting
bridge 1 route ip
line con 0
line vty 0 4
endin order I get these messages;
The processing of Group Policy failed. Windows attempted to read the file \\test.local\sysvol\test.local\Policies\{31B2F340-016D-11D2-945F-00C04FB984F9}\gpt.ini from a domain controller and was not successful. Group Policy settings may not be applied until this event is resolved. This issue may be transient and could be caused by one or more of the following:
a) Name Resolution/Network Connectivity to the current domain controller.
b) File Replication Service Latency (a file created on another domain controller has not replicated to the current domain controller).
c) The Distributed File System (DFS) client has been disabled.
A LDAP connection with domain controller IHIserver01.ihi-press.local for domain TEST is established.
A fatal alert was received from the remote endpoint. The TLS protocol defined fatal alert code is 48. -
How to Configure an Cisco 5505 for PPTP VPN connectivity
I currently have a Cisco ASA 5505(ASA Version 8.2(1), and ASDM gui version 6.2) and a Windows 2008 R2 server with one NIC card. Currently the router is connected to the interent sucessfully using the 'outside' interface(devices connected to the 'inside' interface have access to the internet and are assigned IP addresses via DHCP on the Windows 2008 Server which is also connected to the 'inside' interface) When connected with a client on the inside interface I can establish a VPN connection with the W2008 server, however when I try to connect through the internet I cannot. I have tried researching this on the internet, but have not had much luck. I know it has something to do with pptp port and allowing gre, but I am not familiar enough with configuring Cisco devices or the language they use, to configure this router. I feel as though I am missing something small but very critical. Any help or feedback you can provide regarding this issue is most appreicated, thank you.
*Edit: I have attached a network diagram of what I am trying to accomplish, and I have also attached a dump of the current running-config.Hi,
Below is the link to the admin guide for the RV042. Chapter 9 covers the configuration of site to site VPN’s and begins on page 123.
http://www.cisco.com/en/US/docs/routers/csbr/rv0xx/administration/guide/rv0xx_AG_78-19576.pdf
If you need further assistance please feel free to contact Cisco Small Business for help in configuring and troubleshooting your VPN.
Thank you,
Jason Nickle -
How to configure two separate channels
Hi all,
I'm working with a two nodes RAC using 9.2.0.8 Enterprise edition.
I want to configure the archivelog backup:
CONFIGURE CHANNEL 1 DEVICE TYPE 'SBT_TAPE' CONNECT 'rman_intranet/oracleto@DBCIAT01' PARMS 'ENV=(TDPO_OPTFILE=/home/adsmadm/rman_DBCIAT01/opt/tdpo.opt)';
CONFIGURE CHANNEL 2 DEVICE TYPE 'SBT_TAPE' CONNECT 'rman_intranet/oracleto@DBCIAT03' PARMS 'ENV=(TDPO_OPTFILE=/home/adsmadm/rman_DBCIAT03/opt/tdpo.opt)';
RMAN> run {
2> sql 'alter system switch logfile';
3> sql 'alter system archive log current';
4> sql 'alter system archive log current';
5> backup format 'brman_arch_%s' archivelog all;
6> }
But fails with this error
channel ORA_DISK_1: sid=27 devtype=DISK
RMAN-00571: ===========================================================
RMAN-00569: =============== ERROR MESSAGE STACK FOLLOWS ===============
RMAN-00571: ===========================================================
RMAN-03002: failure of backup command at 01/14/2013 12:49:55
RMAN-06059: expected archived log not found, lost of archived log compromises recoverability
ORA-19625: error identifying file /logs/bbdd/oracle/DBCIAT03/archiver/T0001S0000004618.ARC
ORA-27037: unable to obtain file status
IBM AIX RISC System/6000 Error: 2: No such file or directory
The error is because can't found the archivelog of second node on the first node.
backup format 'brman_arch_%s'
(archivelog like '/logs/bbdd/oracle/DBCIAT01/archiver/%' channel 1 delete all input )
(archivelog like '/logs/bbdd/oracle/DBCIAT03/archiver/%' channel 2 delete all input )
but fails too with this other error:
RMAN-00571: ===========================================================
RMAN-00569: =============== ERROR MESSAGE STACK FOLLOWS ===============
RMAN-00571: ===========================================================
RMAN-00558: error encountered while parsing input commands
RMAN-01005: syntax error: found "integer": expecting one of: "channel_id, double-quoted-string, identifier, single-quoted-string"
RMAN-01007: at line 3 column 66 file: standard input
Please, any idea?
best regardsTHis is just an example..
RMAN can allocate channels to instances it is connected to. For a RAC database, you can connect to the grid TNS alias, which points to all instances. You can then set up parallelism for the device type, and the load will be spread across the RAC instances.
You need to make sure that the password file exists for each instance, and that the user you're connecting as from RMAN has sysdba privileges.
Example:
tnsnames.ora entry:
RACDATABASE =
(DESCRIPTION =
(ADDRESS_LIST =
(LOAD_BALANCE = yes)
(FAILOVER = on)
(ADDRESS = (PROTOCOL = TCP)(HOST = racnode1)(PORT = 1521))
(ADDRESS = (PROTOCOL = TCP)(HOST = racnode2)(PORT = 1521))
(ADDRESS = (PROTOCOL = TCP)(HOST = racnode3)(PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = ORCL)
RMAN connect:
rman target username/password@RACDATABASE
(username/password is for a user with SYSDBA privileges).
RMAN channel configuration:
CONFIGURE DEVICE TYPE DISK BACKUP TYPE TO COMPRESSED BACKUPSET PARALLELISM 4;
This sets up the channels to be spread across the instances based on instance load. -
How to Configure two standalone Server to access with eachother
Hi All,
I have two stand alone Servers (SQL 2000) configured in two PCs in different locations (Location A & Location B) . I want to access Location A database from Location B Viz-Versa.
1. I have a STATIC IP provided by ISP and I m using a router (Linksys E1000)
2. I have Windows Server 2003 installed on one of the PC.
3. Both the Locations are in two different places, ISP providers are also different.
How can I setup the access. I have googled a lot of solutions but not able to crack.
Regards
PradeepHi Pradeep Sriramdas,
SQL Server 2000 was out of support since April,2013. I suggest you can try to install SQL Server 2005 or later version. According to your description, you plan to connect to the SQL Server database engine from another computer, you must enable the protocol
in SQL Server Configuration Manager, such as TCP/IP;
When you want to connect to one instance from another computer, you also must open a communication port in the firewall.
In SQL Server Configuration Manager, you need to configure SQL Server to listen on a specific port; In addition, you configure the remote access server configuration option in SQL Server by using SQL Server Management Studio or Transact-SQL.
You ‘d better adding two different computer in the same domain, and choose to connect to instance via domain name.
There are more details about configuring the connection from another computer, you can review the following article.http://technet.microsoft.com/en-us/library/ms345343.aspx
http://technet.microsoft.com/en-us/library/ms191464.aspx
Regards,
Sofiya Li
Sofiya Li
TechNet Community Support -
How to configure Two Tax Codes for single line item in work order
Hi All,
Please do Review the below scenario and tell me how to solve it.
A) Certified Work Done Gross Bill Amt 100,000
Total Work Done Value 100,000
Less : Labour & Like Charges @ 30 % on Rs 100,000 = 30,000
Vat applicable Amount = 70,000
Add VAT @12.5% Chargeable on Taxable Turnover of Rs. 70,000.00 = 8750
Total Bill Value = 108750
Service Tax @ 12.36% on 33% Value of Rs. 100000 = 4079
G.Bill Amt = 112829
Total Amt Due for Payment = 112829HI, There is a possible solution for this scenario.
1. Create 2 tax codes for VAT and SERVICE Tax at 12.5% and 12.36% respectively
2. While posting the Invoice (TRX - FB60) following steps need to be followed.
3. Amount has to be split into two line items
4. Ist Line Item should have the Vat amount + 70000/- and select relevant tax code that was
created for 12.5%
5. Similarly 2nd Line Item should have Service Tax amount + 30000/- and select relevant tax code that
was created for 12.36%.
Hope this would meet your requirement. If the solution is okay, kindly indicate the points.
Regards
K.Sanjai Babu -
How to configure two seperate accounts in outlook
I want to create two seperate email folders in Outlook 2011. I want one folder that is for personal and one folder that is business. just simply unchecking the group similar folders box does not accomplish this. Has anyone done this? can you help?
I would recommend reposting in the Office for Mac Product Forums I think you have a better chance of getting an answer there.
-
How to configure two TMG 2010 Standard Edition for High Availability
I've classic scenario.
TMG2010 as Edge Firewall, with two NICs, one from ISP and the other for LAN.
I've standard edition, and i want to setup two TMG2010.
Can i create some high availability with these two tmg2010 in some way??
maybe some NLB?? to share their internal IP and Public IP?
in case that TMG01 fails, the services to be offered by TMG02?
Regards
Lasandro LopezHi,
Thank you for your post here.
I do not think it is a good idea.
Please refer to the article below:
http://www.experts-exchange.com/Microsoft/Windows_Security/Q_28014001.html
Best Regards
Quan Gu -
How to configure multiple cisco 3750x switches
Hi All,
we recently bought 25 x 3750-48PS switches and need to roll them out with similar IOS and configuration.
I normally get a console to the switch from my laptop and do one by one.
is there a better way or software which can speed up the process ?
Thanks
QlRead this: ZeroTouch SmartInstall
If configured properly you can load the correct configuration & load the correct IOS in 20 minutes. The entire pile in 20 minutes! -
How can I stop the space bar from acting like the enter key?
I'm doing a little self-project where I enter the band's origin place in the grouping category so I can sort by where they are formed. However, every time I hit space to enter a band or singer's location, iTunes assumes I'm hitting enter, and automatically fills in with whatever previous option is at the top of the list of prior entries. This is really freaking annoying. Is there a way to disable this so I can have spaces in my descriptions without having to delete the extra pieces two or three times for each entry?
The current auto-complete behaviour when you press space is a bug. A workaround is to type say a leading X, then what you want to type, then remove the X.
Or if you hold down Shift as you Right-click > Get Info you get the old style Get Info dialog box which you may find easier to use until the bug gets fixed.
tt2
Maybe you are looking for
-
How to log strings stored in Station Globals and/or PreUUT values?
Hi all, I have a Station Global that is persistent across all UUTs in a particular PC. I have also created a custom PreUUT dialog to obtain user input that applies to the upcoming UUT (I pass this user input to the UUT by storing it in a File Global)
-
Training documents for reports
hi, i am looking for end user training documents for my reports. i need serious help from your side plz, if you have any related documents please forward to my mail address mail id:[email protected]
-
Dear all, I am trying to build a JTable with the below class. If I extend AbstractTableModel my code is working fine but with DefaultTableModel I get the exception: "Exception caught in ...: null". Why do I get null exception in this code? I can't cr
-
FM to run in background - Possibility of interactive feature in background?
Hi experts, I have a requirement to run the function module in background. I feel there is no such possibility to run the function module in background via a sap transaction. It is not my expectation to call the function module in a program and run t
-
I wrote tag class like this public int doStartTag() throws JspException try { System.out.println("Hello doStartTag"); StringBuffer question = new StringBuffer(); question.append("<tr><td>");