Help with CISCO-887VA adsl over pots and PPPoE with dynamic IP
Hi
I've got problem trying to connect the CISCO-887VDSL/ADSL OVER POTS ROUTER to internet. Only got the LAN part working.
I'm trying to setup PPPoE with dynamic IP
Followed CISCO's documentations but the commands used were not recognized by the router. Any simple working config for me to follow will be enough.
I'll appreciate any help. Thanks a lot!
here's my config.
! Last configuration change at 08:31:51 UTC Sat Feb 11 2012
version 15.1
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname router
boot-start-marker
boot-end-marker
no aaa new-model
memory-size iomem 10
crypto pki token default removal timeout 0
ip source-route
ip dhcp excluded-address 10.0.0.1 10.0.0.149
ip dhcp excluded-address 10.0.0.199 10.0.0.254
ip dhcp pool sdm-pool
import all
network 10.0.0.0 255.255.255.0
default-router 10.0.0.1
dns-server x.x.x.x x.x.x.x.x
lease 0 2
ip cef
no ipv6 cef
license udi pid CISCO887VA-K9 sn FGLxxxxxxx
controller VDSL 0
ip ftp username cisco
ip ftp password cisco
interface Ethernet0
pppoe enable group global
pppoe-client dial-pool-number 1
no ip address
shutdown
interface ATM0
no ip address
no atm ilmi-keepalive
pvc 0/35
pppoe-client dial-pool-number 1
interface FastEthernet0
no ip address
interface FastEthernet1
no ip address
interface FastEthernet2
no ip address
interface FastEthernet3
no ip address
interface Vlan1
ip address 10.0.0.1 255.255.255.0
ip nat inside
ip directed-broadcast
ip virtual-reassembly in
ip tcp adjust-mss 1452
interface Dialer1
mtu 1492
ip address negotiated
ip nat outside
ip virtual-reassembly in
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication chap pap callin
ppp chap hostname xxxx
ppp chap password 0 xxxx
ppp pap sent-username xxxx password 0 xxxx
ip forward-protocol nd
no ip http server
no ip http secure-server
ip nat inside source list 1 interface Dialer1 overload
ip route 0.0.0.0 0.0.0.0 Dialer1
ip access-list standard 1
permit 10.0.0.0 0.0.0.255
no cdp run
line con 0
line aux 0
line vty 0 4
login
transport input all
end
Try to check with your ISP the modem string to use for VDSL
and some ISP support direct dhcp on Ethernet0 without PPPoE.
An equivalent config is working for me in Switzerland with Swisscom.
N.B. "modem" under VDSL controller is enable using service internal !
service internal
controller VDSL 0
operating mode vdsl2
modem co5
ip source-route
ip cef
ip dhcp excluded-address 10.0.0.1 10.0.0.149
ip dhcp excluded-address 10.0.0.199 10.0.0.254
ip dhcp pool sdm-pool
import all
network 10.0.0.0 255.255.255.0
default-router 10.0.0.1
dns-server 8.8.8.8
lease 0 2
interface Ethernet0
ip address dhcp
ip nat outside
interface Vlan1
ip address 10.0.0.1 255.255.255.0
ip nat inside
ip tcp adjust-mss 1452
ip nat inside source list 23 interface Ethernet0 overload
access-list 23 permit 10.0.0.0 0.0.0.255
end
Similar Messages
-
my ipad 2 is not turning on, just the apple logo with a moving circle over it and no starting up?
Try using recovery mode
http://support.apple.com/kb/HT1808 -
I have a problem with the synchronisation of my iPhone and iPad with Outlook 2007 on my 64-bit Windows 7 PC. For several years,
I have had no problems with the synchronisation by cord connection and iTunes between these programmes. However, a few months ago I decided to use Mobile Me. However, there were problems with duplication of calendars and then “rogue events” – which could not be deleted – even if deleted on Outlook and on the iPhone (or both at the same time) – they would just reappear after the next synchronisation. All other synchronisation areas (eg Contacts, Notes etc) work fine.
I have looked for help through the Apple Support Community and tried many things. I have repaired my Outlook. I have repaired my .pst file in Windows. I have re-installed the latest version of iTunes on my PC. I have re-installed the firmware on my iPhone. I have tried many permutations on my iPhone. I have closed down all Mobile Me functions on the iPhone. I have spent upwards of 24 hours trying to solve this problem.
What am I left with? Outlook works seamlessly on my PC. My iPhone calendar now has no events from my calendar, but does not synchronise through iTunes. Nor does it send events initiated on the iPhone to the Outlook. I am at the point of abandoning iPhones and iPads altogether. I need to have a properly synchronising calendar on my phone. Do you have any suggestions?In the control panel goto the "Lenovo - Power Manager" and click the battery tab, there is a maintenance button in there that will let you change the charging profile for your battery. (from memory, so exact wording may be off)
The lower the numbers you use there, the longer the battery *should* last. These batteries degrade faster at higher charge levels, however storing them at too low of levels is also not good for them... I've read that 40% is optimal, but just not realistic if you use your computer.
--- ThinkPad T61 / Win 7 / Core 2 / 4gb RAM / Nvidia / Still used daily --- ThinkPad Edge 15/ i5 / Win 7 / TrueCrypt / 8gb RAM / Hated it, died at 1 yr 1 mo old --- ThinkPad T510 / Win 7 / TrueCrypt / i5 / 8gb RAM / Nvidia / Current primary machine --- ThinkPad X220 / i7 / IPS / 4gb / TrueCrypt / My Road Machine -
With my i phone 4 , the Push notifications doesn't work for apps like (fb viber , whatsapp etc ) it only works for the official apps like message even when im using the phone, has this probleme with the iOs 6.0.1 and also with the iOs 6.1
This isn't an issue. Notice the screen prior to the one that shows usage has an iCloud section and a Manage Storage button. For this button to activate ios needs to download a few kb from icloud. Switching back to this screen forces ios to download those few kb.
-
I have 2 apple ID one for Egypt and other for USA , now I try to update the software but I get a message said that this software download with other ID, then I logout and sign with second ID but i got the same message again ... Now I can not sign in more
Any solution ?
I'm using iOS 6.1.2 IPad 3
RegardsI have also noticed the same "problem". I do not fully understand the impact of using the same ID on multiple computers and devices if I want to keep them all in sync.
-
i just received my i phone 4,inserted Amayim with 4G plan,but showing noservice and bar with emergency calls only screen.Also when i down loaded i tunes to my laptop (windows7) there is an error(9808) message saying i tunes store not supported completely.
first of all the iphone 4 is not a 4G phone
second it sounds like your iphone could be locked to another operator then the sim you have inserted -
Over saturated and contrast with previews in Aperture 3.4.5
When I import photos from my Nikon D700 I import both RAW and JPEG with RAW as the master. The initial previews are great, but as soon as aperture updates the preview it becomes over saturated with too much contrast. I have tried post import processing with both Aperture and Camera presets with the same result. I have followed other similar threads that go into the technical details of what a preview is, this is fine, but what I want to know is what I'm doing that stops me from keeping the original good preview image. Can anyone tell me exactly where the initial preview was generated adn how to keep it?
Cheers
P.S. i have temporarily disabled this terrible change by toggling 'P'Can anyone tell me exactly where the initial preview was generated adn how to keep it?
Haggy72,
as you have seen the many threads on previews, I am sure, you know already, that the initial preview is the preview generated by your camera. It reflects all raw processing and all effects set in your camera, but it does not show, what the unprocessed raw image is like.
Aperture will create a preview, that is showing excatly, how the raw image will look, without any edits applied. When you are using the raw as original image file, it is necessary, that the preview (and the thumbnail) will show you the raw image as it is. How else are you to know, what edits will be necessary to create the image you want?
if you want to keep the original, camera generated preview, use the jpeg as original image file. That image is a high resolution version of the preview you like.
-- Léonie -
Lync 2013 PSTN calling not working with Sonus SBC 1000 over TLS and SRTP
Dear All,
We have recently installed Lync 2013 Enterprise Edition with a Pool of 3 FE Servers (MEDIATION COLLOCATED).
We need to implement TLS and SRTP with Sonus SBC 1000. However calls are not routing b/w SBC and Lync.
We are using wild card certificate with multiple SIP Domains as SAN(s), for internal FE servers as well SBC.
Also i would like to mentioned here that inbound and outbound calls are routing properly when we tested it over TCP.
When I move to TLS Only calls from Lync to SBC (outgoing) are working without encryption.
Here are the OCS Logger traces for incoming calls which are not landing on lync:
TL_INFO(TF_PROTOCOL) [1]2C5C.0D30::04/30/2014-14:35:18.020.00026518.020.00026518.020.00026518.020.00026518.020.00026518.020.00026518.020.00026518.020.000265d2
(S4,SipMessage.DataLoggingHelper:sipmessage.cs(774))[3491463749]
>>>>>>>>>>>>Outgoing SipMessage c=[<SipTlsConnection_AE0419>], 10.10.0.11:5067->10.10.7.50:25678
SIP/2.0 400 Bad Request
FROM: "3158222726"<sip:[email protected]>;tag=ac3201ce-4d7
TO: <sip:[email protected]:5067>;epid=D2091CF753;tag=f373543c
CSEQ: 2 INVITE
CALL-ID: [email protected]
VIA: SIP/2.0/TLS 10.10.7.50:5067;branch=z9hG4bK-UX-ac32-01ce-0b14
CONTENT-LENGTH: 0
SERVER: RTCC/5.0.0.0 MediationServer
------------EndOfOutgoing SipMessage
TL_INFO(TF_PROTOCOL) [1]2C5C.0D30::04/30/2014-14:35:18.027.00026518.027.00026518.027.00026518.027.00026518.027.00026518.027.00026518.027.00026518.027.000265d7
(S4,SipMessage.DataLoggingHelper:sipmessage.cs(774))[2666394843]
>>>>>>>>>>>>Outgoing SipMessage c=[<SipTlsConnection_370F030>], 10.10.0.11:58059->10.10.0.13:5061
SERVICE sip:2138797082;[email protected];user=phone SIP/2.0
FROM: <sip:2138797082;[email protected];user=phone>;epid=DCFDB95F4C;tag=17d286a93
TO: <sip:2138797082;[email protected];user=phone>
CSEQ: 3 SERVICE
CALL-ID: de750f98bdd94e908be5f2f975228ff7
MAX-FORWARDS: 70
VIA: SIP/2.0/TLS 10.10.0.11:58059;branch=z9hG4bKd47f1d3c
CONTACT: <sip:[email protected];gruu;opaque=srvr:MediationServer:CiGdW3iH5FiI3Qvr3PIKGQAA>
CONTENT-LENGTH: 630
SUPPORTED: gruu-10
USER-AGENT: RTCC/5.0.0.0 MediationServer
CONTENT-TYPE: application/msrtc-reporterror+xml
<?xml version="1.0" encoding="us-ascii"?>
<reportError xmlns="http://schemas.microsoft.com/2006/09/sip/error-reporting">
<error callId="[email protected]" fromUri="sip:3158222726;[email protected];user=phone" toUri="sip:2138797082;[email protected];user=phone" fromTag="ac3201ce-4d7"
toTag="" requestType="INVITE" contentType="application/sdp;call-type=audio" responseCode="400"><diagHeader>10013;reason="Gateway peer in inbound call is not found in topology document or does not depend
on this Mediation Server"</diagHeader><progressReports /></error></reportError>------------EndOfOutgoing SipMessage
Call
Send SMS
Add to Skype
You'll need Skype CreditFree via Skype@Paul, Thanks for you response.
All ports / IP Add / DNS are defined properly. Telenet on listening port is working.
We are using Public Certificate for 3 Domains (wild card) and same is loaded and verified in SBC
I've not reviewed the OCS logs properly posted above.
What i've found or seems to me is that in a TLS Calls:
After receiving SIP Invite from SBC, mediation server started TLS Negotiation Process b/w Lync 2013 Server Pool and it fails.
SIP Domains:
contoso.com (default)
fabrikam.com
Lync FE Pool (lync.contoso.com
Here are the some more logs.
TL_INFO(TF_PROTOCOL) [0]2DF8.2930::05/01/2014-11:50:31.612.00025e49 (S4,SipMessage.DataLoggingHelper:sipmessage.cs(774))[2716989131]
<<<<<<<<<<<<Incoming SipMessage c=[<SipTlsConnection_103DFE0>], 10.10.0.11:5067<-10.10.7.50:24591
INVITE sip:[email protected]:5067 SIP/2.0
FROM: "3158222726" <sip:[email protected]>;tag=ac3201ce-ae
TO: <sip:[email protected]:5067>
CSEQ: 2 INVITE
CALL-ID: [email protected]
MAX-FORWARDS: 70
VIA: SIP/2.0/TLS 10.10.7.50:5067;branch=z9hG4bK-UX-ac32-01ce-010c
CONTACT: <sip:[email protected]:5067;transport=TLS>
CONTENT-LENGTH: 406
SUPPORTED: replaces,update,100rel
USER-AGENT: SONUS SBC1000 3.1.2v293 Sonus SBC
CONTENT-TYPE: application/sdp
ALLOW: INVITE, ACK, CANCEL, BYE, NOTIFY, OPTIONS, REFER, REGISTER, UPDATE, PRACK
P-ASSERTED-IDENTITY: "3158222726" <sip:[email protected]>
v=0
o=SBC 9 1001 IN IP4 10.10.7.50
s=VoipCall
c=IN IP4 10.10.7.50
t=0 0
m=audio 16418 RTP/AVP 8 0 101 13
c=IN IP4 10.10.7.50
a=rtpmap:8 PCMA/8000/1
a=rtpmap:0 PCMU/8000/1
a=rtpmap:101 telephone-event/8000
a=fmtp:101 0-15
a=rtpmap:13 CN/8000
a=ptime:20
a=tcap:1 RTP/SAVP
a=pcfg:1 t=1
a=crypto:1 AES_CM_128_HMAC_SHA1_80 inline:pqL6Tke8pVmXPuplJ1G3+Sr9jM97H8R7iBagWzzh|2^31|1:1
a=sendrecv
------------EndOfIncoming SipMessage
TL_INFO(TF_PROTOCOL) [1]2DF8.0E04::05/01/2014-11:50:31.665.00025e8e (S4,SipMessage.DataLoggingHelper:sipmessage.cs(774))[2716989131]
>>>>>>>>>>>>Outgoing SipMessage c=[<SipTlsConnection_103DFE0>], 10.10.0.11:5067->10.10.7.50:24591
SIP/2.0 100 Trying
FROM: "3158222726"<sip:[email protected]>;tag=ac3201ce-ae
TO: <sip:[email protected]:5067>
CSEQ: 2 INVITE
CALL-ID: [email protected]
VIA: SIP/2.0/TLS 10.10.7.50:5067;branch=z9hG4bK-UX-ac32-01ce-010c
CONTENT-LENGTH: 0
------------EndOfOutgoing SipMessage
TL_INFO(TF_CONNECTION) [1]184C.0EFC::05/01/2014-11:50:32.652.00025f32 (SIPStack,SIPAdminLog::WriteConnectionEvent:SIPAdminLog.cpp(454))[946832530] $$begin_record
Severity: information
Text: TLS negotiation started
Local-IP: 10.10.0.11:5061
Peer-IP: 10.10.0.11:52529
Connection-ID: 0x10BE00
Transport: TLS
$$end_record
TL_INFO(TF_PROTOCOL) [1]184C.0EFC::05/01/2014-11:50:32.669.00026236 (SIPStack,SIPAdminLog::ProtocolRecord::Flush:ProtocolRecord.cpp(265))[1853494582] $$begin_record
Trace-Correlation-Id: 1853494582
Instance-Id: 425D
Direction: incoming
Peer: 10.10.0.11:52529
Message-Type: request
Start-Line: NEGOTIATE sip:127.0.0.1:5061 SIP/2.0
FROM: <sip:contoso.com>;ms-fe=LYNCFE1.fabrikam.com
TO: <sip:contoso.com>
CALL-ID: aa53739ef9b34b93ba9c97d3ee56cb99
CSEQ: 1 NEGOTIATE
VIA: SIP/2.0/TLS 10.10.0.11:52529
MAX-FORWARDS: 0
CONTENT-LENGTH: 0
SUPPORTED: NewNegotiate
SUPPORTED: ECC
REQUIRE: ms-feature-info
SERVER: RTC/5.0
$$end_record
TL_INFO(TF_CONNECTION) [1]184C.0EFC::05/01/2014-11:50:32.669.0002636e (SIPStack,SIPAdminLog::WriteConnectionEvent:SIPAdminLog.cpp(383))[946832530] $$begin_record
Severity: information
Text: Connection established
Peer-IP: 10.10.0.11:52529
Peer: lync.contoso.com:52529;ms-fe=LYNCFE1.fabrikam.com
Peer-Cert: contoso.com(LYNCFE1.fabrikam.com)
Transport: M-TLS
Data: alertable="yes"
$$end_record
TL_WARN(TF_CONNECTION) [1]184C.0EFC::05/01/2014-11:50:32.669.00026387 (SIPStack,SIPAdminLog::WriteConnectionEvent:SIPAdminLog.cpp(386))[946832530] $$begin_record
Severity: warning
Text: The pool FQDN provided by the peer in its NEGOTIATE feature information does not match the pool configured in CMS for the server FQDN that it provided
Peer-IP: 10.10.0.11:52529
Peer: lync.contoso.com:52529;ms-fe=LYNCFE1.fabrikam.com
Peer-Cert: contoso.com(LYNCFE1.fabrikam.com)
Transport: M-TLS
Data: fqdn="LYNCFE1.fabrikam.com";pool="contoso.com";expected-fqdn="lync.contoso.com";info="Possible server configuration issue"
$$end_record
TL_INFO(TF_DIAG) [1]184C.0EFC::05/01/2014-11:50:32.670.000265be (SIPStack,SIPAdminLog::WriteDiagnosticEvent:SIPAdminLog.cpp(802))[1853494582] $$begin_record
Severity: information
Text: Routed a locally generated response
SIP-Start-Line: SIP/2.0 200 OK
SIP-Call-ID: aa53739ef9b34b93ba9c97d3ee56cb99
SIP-CSeq: 1 NEGOTIATE
Peer: lync.contoso.com:52529;ms-fe=LYNCFE1.fabrikam.com
$$end_record
TL_INFO(TF_PROTOCOL) [1]184C.0EFC::05/01/2014-11:50:32.670.00026615 (SIPStack,SIPAdminLog::ProtocolRecord::Flush:ProtocolRecord.cpp(265))[1853494582] $$begin_record
Trace-Correlation-Id: 1853494582
Instance-Id: 425E
Direction: outgoing;source="local"
Peer: lync.contoso.com:52529;ms-fe=LYNCFE1.fabrikam.com
Message-Type: response
Start-Line: SIP/2.0 200 OK
FROM: <sip:contoso.com>;ms-fe=LYNCFE1.fabrikam.com
To: <sip:contoso.com>;tag=C3A751556F332F7265E9BA2517C878D4
CALL-ID: aa53739ef9b34b93ba9c97d3ee56cb99
CSEQ: 1 NEGOTIATE
Via: SIP/2.0/TLS 10.10.0.11:52529;ms-received-port=52529;ms-received-cid=10BE00
Content-Length: 0
Require: ms-feature-info
Supported: NewNegotiate,OCSNative,ECC,IPv6,TlsRecordSplit
Server: RTC/5.0
$$end_record
TL_INFO(TF_PROTOCOL) [1]2DF8.1078::05/01/2014-11:50:32.671.000266da (S4,SipMessage.DataLoggingHelper:sipmessage.cs(774))[720988281]
>>>>>>>>>>>>Outgoing SipMessage c=[<SipTlsConnection_F8A09B>], 10.10.0.11:52529->10.10.0.11:5061
SERVICE sip:2138797082;[email protected];user=phone SIP/2.0
FROM: <sip:2138797082;[email protected];user=phone>;epid=16FEE4A02E;tag=22fd877f3a
TO: <sip:2138797082;[email protected];user=phone>
CSEQ: 3 SERVICE
CALL-ID: ac0f7bc4cdc94c1dbd0bb51c7c02c890
MAX-FORWARDS: 70
VIA: SIP/2.0/TLS 10.10.0.11:52529;branch=z9hG4bK67a4c9d1
CONTACT: <sip:[email protected];gruu;opaque=srvr:MediationServer:CiGdW3iH5FiI3Qvr3PIKGQAA>
CONTENT-LENGTH: 628
SUPPORTED: gruu-10
USER-AGENT: RTCC/5.0.0.0 MediationServer
CONTENT-TYPE: application/msrtc-reporterror+xml
- <reportError xmlns="http://schemas.microsoft.com/2006/09/sip/error-reporting">
- <error callId="[email protected]"
fromUri="sip:3158222726;[email protected];user=phone"
toUri="sip:2138797082;[email protected];user=phone"
fromTag="ac3201ce-ae"
toTag=""
requestType="INVITE"
contentType="application/sdp;call-type=audio"
responseCode="400">
<diagHeader>10013;reason="Gateway peer in inbound call is not found in topology document or does not depend on this Mediation Server"</diagHeader>
<progressReports/>
- </error>
------------EndOfOutgoing SipMessage -
Images are not downloaded at all and page looks broken.
The same page works fine over HTTP but shows the problem over HTTPS. Works fine in firefox and chrome.
Checked and found the problem in IE 9, 10, 11
Is it some bug in IE, I have searched the forums and searched internet. Got following but are not relevant to this case.
Resetting src of the img (Ruled out, not doing any reset)
Do not save encrypted pages to disk is checked in advanced security options (Ruled out, unchecked)
Using TLS 1.2 with SSL 2.0 (Ruled out, SSL 2.0 unchecked)
Cache-preventing headers: Cache-Control header with the tokens no-cache, no-store (Ruled out, no such headers)
Restarts due to parser reset owing XML Namespace declaration, Meta tags etc. (Ruled out, image tags are afterwards)
Thanks in advance for help!I probably encountered the same problem.
What happens when you disable the 'Use TLS 1.0' checkbox in Internet Options, Advanced, Security, 'Use TLS 1.0'?
The only enabled option I have in IE is 'Use SSL 3.0'.
Source:
http://social.msdn.microsoft.com/Forums/ie/en-US/88a58e78-ebb4-469d-a361-0d3762a4cf80/ie10-reports-aborted-js-and-css-downloads-randomly?forum=iewebdevelopment -
This problem started immediately after I upgraded to Firefox 9.0.1
If I open my inbox in my New Yahoo Mail, then open an email with attachments and then open the attachments to "view as a slide show"....I can't close the slide show and return to the email by clicking on the "return to Yahoo" button. If you click on it, it returns to the first pic shown, and if you click on it again, the pics disappear and a gray haze appears over most of the screen but none of the features under the gray screen work. I have found that if I hit the back page and then forward page buttons, I can get back to my inbox eventually, but this is a terrible "pain in the ass"!Clear the cache and the cookies from sites that cause problems.
"Clear the Cache":
*Tools > Options > Advanced > Network > Offline Storage (Cache): "Clear Now"
"Remove Cookies" from sites causing problems:
*Tools > Options > Privacy > Cookies: "Show Cookies"
Start Firefox in <u>[[Safe Mode]]</u> to check if one of the extensions or if hardware acceleration is causing the problem (switch to the DEFAULT theme: Firefox (Tools) > Add-ons > Appearance/Themes).
*Don't make any changes on the Safe mode start window.
*https://support.mozilla.org/kb/Safe+Mode -
As mentioned above, when I opened Firefox this morning it installed automatically an update w/o me agreeing and I don't know what was isntalled. Since then I cannot open Firefox. Mozilla Crash Reporter opens and thell me Firefox had a problem and crashed. "We'll try to restore your tabs and windows when it restarts.
To help us diagnose and fix the problem, you can send us a crash report."
I press restart Firefox but I always just get the same message. I uninstalled it and downloaded it again, nothing is changing. I urgentlyu need to use the bookmarks as I don't have them in Explorer which I have to use now.
Thank youYou need "sysinternal's process explorer", it is free and can replace the Microsoft process explorer, that you get by "CTRL+ALT+DELETE". Either program will allow you to kill the instances of FF that didn't die as they should have, when you closed them. Sysinternal is easier to use, it is a graphic display with many options. Do not push "CTRL+ALT+DELETE" twice unless you want to reboot, that is its default behaviour under Microsoft.
-
Cisco 876 ADSL over ISDN Router
I am facing some problem in using ISDN bri S/T interface for connectivity to HO PRI router.I am not using the ATM interface of this router.The isdn status always shows that the isdn layer 1 and 2 is deactivated. IF i connect the same bri cable to other isdn router it works fine.
Is their any special configuration or command required in 876 router for the isdn dialing?
I found on cisco that the 876 router ISDN bri S/T interface is for the out-of-band mangement and dial backup.
Can i use this interface for the normal isdn dialing?
need some clarification.
regards,
khalid siddiqFind the attach detail.
SCIENTECH-AVEER#
SCIENTECH-AVEER#sh runn
SCIENTECH-AVEER#sh running-config
Building configuration...
Current configuration : 1505 bytes
version 12.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname SCIENTECH-AVEER
boot-start-marker
boot-end-marker
username INET-Rou-ESA password 0 cisco123
no aaa new-model
ip subnet-zero
ip cef
no ftp-server write-enable
isdn switch-type basic-net3
isdn tei-negotiation first-call
interface BRI0
description connected to HQ PRI
no ip address
encapsulation ppp
dialer pool-member 1
isdn switch-type basic-net3
ppp authentication chap
interface ATM0
no ip address
no atm ilmi-keepalive
dsl operating-mode auto
interface FastEthernet0
no ip address
interface FastEthernet1
no ip address
shutdown
interface FastEthernet2
no ip address
shutdown
interface FastEthernet3
no ip address
shutdown
interface Vlan1
ip address 192.168.201.25 255.255.255.0
interface Dialer0
ip address negotiated
encapsulation ppp
dialer pool 2
dialer string 404444
dialer-group 1
router rip
network 192.168.201.0
network 192.168.251.0
ip classless
no ip http server
no ip http secure-server
dialer-list 1 protocol ip permit
dialer-list 2 protocol ip permit
control-plane
line con 0
password gbm4ibm
login
no modem enable
transport preferred all
transport output all
line aux 0
transport preferred all
transport output all
line vty 0 4
password gbm4ibm
login
transport preferred all
transport input all
transport output all
scheduler max-task-time 5000
end
SCIENTECH-AVEER# sh ver
Cisco IOS Software, C870 Software (C870-ADVSECURITYK9-M), Version 12.3(8)YI2, RE
LEASE SOFTWARE (fc1)
Synched to technology version 12.3(10.3)T2
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2005 by Cisco Systems, Inc.
Compiled Tue 14-Jun-05 18:58 by ealyon
ROM: System Bootstrap, Version 12.3(8r)YI2, RELEASE SOFTWARE
ROM: Cisco IOS Software, C870 Software (C870-ADVSECURITYK9-M), Version 12.3(8)YI
2, RELEASE SOFTWARE (fc1)
SCIENTECH-AVEER uptime is 22 hours, 13 minutes
System returned to ROM by reload
System image file is "flash:c870-advsecurityk9-mz.123-8.YI2.bin"
Last reload reason: Reload command
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
Cisco 876 (MPC8272) processor (revision 0x100) with 118784K/12288K bytes of memo
ry.
Processor board ID FCZ100223M7
MPC8272 CPU Rev: Part Number 0xC, Mask Number 0x10
4 FastEthernet interfaces
1 ISDN Basic Rate interface
1 ATM interface
128K bytes of non-volatile configuration memory.
24576K bytes of processor board System flash (Intel Strataflash)
Configuration register is 0x2102 -
NME-NAM with Cisco Prime 5.1.2 and IOS Firewall
Hello,
I have installed and configured the Cisco NME-NAM with Prime 5.1.2 and have access to the NAM via a web browser. It is not picking up any data even though I havew configured the following:
internal data source
network site 10.10.16.0/20
All reports show "No data for selected time interval"
I am running IOS 15.1 on a 2811 with IOS firewall enabled.
Do I need to create a FW rule to allow traffic to be monitored by the NME-NAM?
Thank you,
MatthewHi rajeeshp,
Currently I am not allowed to upgrade it because of internal procedures involved in upgrading a specific piece of software (obtaining permissions from various departments). Is it free to upgrade from 1.2 to 1.3 or there is a specific charge for that.
Predrag Petrovic -
Help maverick does not synchronise adress book and calendar with itunes
Apple supressed the itunes synchronisation of calendar and adress book with maverick!
Is there an other possibility to do this locally?
I don't want to share my private things with america!appid
thank you for your message
i wrote to the European Commissiion yesterday
i haved a call with Apple assistance a this moment
the first person could'nt help me and her responsable tell me that this "evolution" was signaled in the
General conditions of sale when i install Maverick, and thus it was no my problem
the only solution Apple propose is to go back to Mountain Lion
do you know how to do that
thanks for help -
Hello!
After the PRISM scandal I even want so much more to sync ALL relevant data between iOS and Mountain Lion Apps over iTunes (USB or WLAN).
I am very disappointed in the (still) missing choice of means of sync for some data.
Or am I missing something?
Is there a possiblity to sync notes and reminders between a Mac and an iPhone over iTunes (USB)?
If there isn't any:
I don't understand, why you can choose for most of the data,
but not for notes and reminders.
Here the data you have the choice to sync over iTunes (USB or WLAN):
> apps
> calendar
> contacts
> music
> playlists
> movies
> videos
> podcasts
> books
> photos
Here the Data you don't have a choice. If you want to sync them,
you have to do it over the Internet and iCloud:
> notes
> reminders
I am the only one, using my Mac Pro and my iPhone.
I don't need over the air / Internet syncing for most personal data.
I don't want to share more informations than necessary over the Internet or / and iCloud because of
> Security,
> my data cap of my mobile provider and
> control of my data.
> PRISM
Many big companies like Amazon, Sony, Valve and others had problems with hackers.
And even I trust Apple very much, Apple can't promise absolute security of data saved in iCloud.
To have the choice to sync things over iCloud is fantastic.
To be forced to sync things only over iCloud / Internet is worrying and disturbing.
Greetings from Germany
Matthias B.The PRISM-Scandal is proof to me, that my wish isn`t dated at all ...
To have the choice to sync things over iCloud is fantastic.
To be forced to sync things only over iCloud / Internet is worrying and disturbing.
Especially now with PRISM
Greetings from Germany
Matthias B.
Maybe you are looking for
-
OIM: What is the purpose of "Update" while editing group memberships
Hi, This is when you lookup a user's Resource Profile and go to "Edit" link. The process form shows up along with a drop down to edit the group memberships. When we select one of the choices such as "Groups" another window pops up where we could add
-
Robohelp 10 not wysiwig: Design pod vs. preview and output
Converting MSWord docx files to WebHelp w/RH10. Using imported CSS. In the Design pod the output looks spaced as expected but in Preview (CTRL + W) or actual output, the spacing is all wrong. It is as though my CSS is not being enforced. BUT then i s
-
Update statement shows error while compiling in forms
i have the following query which works fine through TOAD,but in forms while compiling it gave error: "too many declarations of 'DECODE' match this call". Can any body suggest me a workaround for this query to avoid this error. UPDATE job_headers_web
-
How to :Logging or System.out.println????
Hi, Iam not able to see any System.out.println output in SAP? where exactly can i see it? any configuration required to enable logging? if so how?? please help
-
How do you delete an application on Macbook pro 2012?
I just downloaded something off the web and no longer need it. It seems silly, but how can i delete the application?