Help with set up please
I have just bought a second airport xtreme card for my G5 powermac and now have this and the G5 imac wirelessly connected via a belkin F5D7630 router. Strangley I have noticed that the signal strength is weaker on my powermac compared with the Imac. I have checked the installation of the card and ensured that I have the external arial connected to the back on the computer. As I am typing this I have noticed that I have 2 bars showing on the menubar and the imac has 5 bars. These machines are in different rooms on the same floor and the router is in another room on the same floor.
I called Belkin and they said that I should change my settings to 10 half duplex. Apparently the airpport cards are set for 10 full duplex. Well, i don't know where I would make this change and whether the change is actually needed.
Does the signal level impact on the connection speed?
WHat does 'interface robustness' mean and should I have it ticked in the menu?
What is this 10 half duplex stuff about and how do I change it?
Please can someone help me on this one - It is most frustrating
"10 half duplex" applies to cabled ethernet network connections - not wireless network connections. This suggestion isn't of any relevance to your problem.
"Interference robustness" helps alleviate the effects of some types of radiofrequency interference. Don't enable this feature unless interference is known to be an issue. Are the any other wireless networks in range of yours (listed in the Mac's Airport menu)?
Double check the connection of the internal Airport antenna cable to the Airport Extreme card on the G5. Make sure the connector is FULLY seated, which can take some force to do properly.
Similar Messages
-
JUST BOUGHT WRT54G LINKSYS ROUTER, NEED HELP WITH SET UP PLEASE!
I've tried everything to get my WRT54G to work but no matter what I do I can't get past step ten on the CD. It asks for my password and when i type and confirm type it then press next it comes up with, Router Configuration Error. Would you like to try again?
I've been stuck at this for over two hours now, please help me
Madi-LiuI had the same problem this past weekend. The CD is the problem. It is much easier to go to www.linksys.com/connect and first update the firmware (if applicable), and then use the EasyLink Connect tool. I works very well.
Good luck,
Mike -
Help with access control please
So I'm trying to set up my brother's PSP to the wirless network through MAC address timed access. What I want to do is make it so that he can only access it through certain times in the day. I'm having troubles with actually getting it to work. Everytime I set it up, the PSP only show's up as a DHCP client and not a Wireless client. I tried the option panel with the add wireless clients through the first try access. Could I get some help with this issue please? Thanks!
Just to calm your fears... There is no conspiracy. If someone had an answer or a suggestion they would post it.
-
I need help with setting up my Sun Java Studio Creator
Hello all, i need help with setting up the Studio Creator, i"m new to all that staff so is there anyone to help me just a little with all that if yes email me at [email protected] or get me on AOL Instant Messanger with the screen name: wretch17
thanks :-)Hi,
Welcome to the Creator community! Thanks for your interst in Sun Java Studio Creator. Please feel free to post any question related to creator on this forum .
Take a look the creator website at
http://developers.sun.com/prodtech/javatools/jscreator/
CreatorTeam -
Can anyone help with setting up AirPrint on my iPhone 4
Can anyone help with setting up AirPrint on my iPhone 4. Printer is ready.
you have a compatable printer correct? http://support.apple.com/kb/ht4356
if you do may i introduce you to a hassel free app for your mac called printopia i use it also very easy to set up and use
http://www.udeo.com/mac/printopia/
hope thats helped
Goody -
Purchased extreme to replace modem/router DSL used telephone cord need help with set up
Prior to purchasing Airport Extreme had a standard modem/ wireless router from ATT for DSL. I have two macbooks both dropped connections while online with older modem.
Airport Extreme purchased to correct connection issues I need help with set up. The older modem just used telephone cord. I tried to use telephone with extreme it did not work.
How do I get extreme to work as the modem and router ?How do I get extreme to work as the modem and router ?
you can't. the extreme is only a router. you need a separate modem (or disable the wireless part of your old router and use it as a modem - if that's possible). -
I need help with setting up time machine for backup
I would like help with setting up time machine for backup.
You will need an external hard drive (formatted for a Mac).
Then you plug it in and go to system preferences>time machine and select the external HD and turn it on.
The backups are automatic.
Barry -
Help with set(index, object) please / new to java
private static void setDobject(Rectangle [] setrect)
LinkedList<Rectangle> rects = new LinkedList<Rectangle>();
Rectangle myrectangle = new Rectangle(9.0,9.0);
rects.set(1,myrectangle);
for(Rectangle x : setrect)
System.out.print("Rectangle: ");
System.out.println(x.getLength() + " by " + x.getWidth());
} //End of for loop
} //End of unsorted
} the other previous code works, i have used the add(object) and it works here is the code for that:
private static void addDobject(Rectangle [] addrect)
LinkedList<Rectangle> rects = new LinkedList<Rectangle>();
Rectangle myrectangle = new Rectangle(9.0,9.0);
rects.add(myrectangle);
for(Rectangle x : rects)
System.out.print("Rectangle: ");
System.out.println(x.getLength() + " by " + x.getWidth());
} //End of for loop
System.out.println();
} //End of unsorted
this is the output error it is giving me :
Part 1 : An Array List of Rectangles
Enter length or 999 to exit: 3
Enter width: 2
Enter length or 999 to exit: 1
Enter width: 2
Enter length or 999 to exit: 10
Enter width: 20
Enter length or 999 to exit: 999
Rectangle: 3.0 by 2.0
Rectangle: 1.0 by 2.0
Rectangle: 10.0 by 20.0
Display Object with added item
Rectangle: 3.0 by 2.0
Rectangle: 1.0 by 2.0
Rectangle: 10.0 by 20.0
Rectangle: 9.0 by 9.0
Displaying Objects with SET item
Exception in thread "main" java.lang.IndexOutOfBoundsException: Index: 1, Size:
0
at java.util.LinkedList.entry(LinkedList.java:365)
at java.util.LinkedList.set(LinkedList.java:328)
at Lab11.setDobject(Lab11.java:129)
at Lab11.main(Lab11.java:78)
Press any key to continue...
finally here is the Rectangle class i'm using:
public class Rectangle
private double length; // Instance variables
private double width;
public Rectangle(double l, double w) // Constructor method
length = l;
width = w;
} // end Rectangle constructor
public double getLength() // getter
return length;
} // end getLength
public double getWidth() // getter
return width;
} // end getWidth
public void setLength(double l) // setter
length = l;
} // end setLength
public void setWidth(double w) // setter
width = w;
} // end setWidth
public double calculateArea() // calculation method
return length * width;
} // end calculateArea
public void displayRectangle() // display method
System.out.println("Rectangle Length = " + length);
System.out.println("Rectangle Width = " + width);
} // end displayRectangle
} // Rectangle ClassHope you can help guys! thanks!LinkedList<Rectangle> rects = new LinkedList<Rectangle>();rects is an empty LinkedList at this point. It has no elements added to it.
rects.set(1,myrectangle);So you can't set the item at index 1 (the 2nd element in the list) because it doesn't even exist. You need to add items to it. -
Help with CLASSPATH variable please
Hi everyone!!
Please, help to set up my classpath variable. I know I know I have guidelines in API but I don't achieve it, I'm so clumsy.
I've formated my hard disk and installed everything again, but the classpath is wrong because I can't compile my java files.
I've tried with this:
C:\Program Files\Java\jdk1.5.0_06\scr.zip;C:\Program Files\Java\jdk1.5.0_06\javac.exe;C:\Program Files\Java\jdk1.5.0_06\java.exe
I've also tried with the same lines but unnaming files (finishing with '\')
What am I doing wrong?
Thank you very much for your attention and help.
Merry Christmas and Happy New Year!!
And I hope the Three Wise Men bring you everything!!Please post your exact problem and the exact error message. I think you are having a problem compiling, but I am not sure. What is not working? What is the error?
You posted a path, but if that is your Classpath, you should not have javac or java in the Classpath. -
Help with Required fields-PLEASE
I have been attempting to get help with a required field and one of the forum helpers said he got it to work for me but I cannot and I have not been able to get any more responses from him to help me further.
I am attempting to have a radio box when the YES is selected to require another field to be completed. The script I was provided with is:
getField("Location").required = (getField("Group1").value == "Yes");
Location being the field that I require to be filled in if Group 1 is Yes. The previous forum helper indicated that I had to have this script in both fields in Group 1 and when I do that, nothing different happens.
What am I doing wrong?
Please, I need to fix this right away and I will be using this java script on many other forms that I have so I need to get this done soon.
Thank you in advance.Wht you want can get somewhat complicated. One way to prevent subsequent fields from being used is to set them to read-only and/or hidden. You could then use the Validate event of the text field to validate the entry and enable the subsequent fields if it is filled-in adequately. In general, you should also reset the fields whenever you hide them, so they don't contain potentially invalid data from previously being filled-in. So you could initially have the fields set to be hidden, and only unhide them if No is selected, or if Yes is selected and the required text field is filled-in.
I realize this may not be as helpful as you had hoped for, but I can't suggest specific code without knowing more about the form. -
Help with UILabel subclass please
Hello all... I have a UILabel subclass I call CustomLabel. Ive been googling and reading the apple docs this entire week to figure this out. The few examples Ive seen, I dont think Im doing it right.
Im trying to create a subclass to use throughout my project. Every label will have these properties so I figured why not subclass. So through a lot of trial and error I ended up with this...
CustomLabel.h
#import <UIKit/UIKit.h>
@interface CustomLabel : UILabel {
@property (nonatomic) CGSize shadowOffset;
@property (nonatomic) UITextAlignment *textAlignment;
@property (nonatomic, retain) UIColor *shadowColor;
@property (nonatomic, retain) UIColor *textColor;
@property (nonatomic, retain) UIColor *backgroundColor;
@property (nonatomic, retain) UIFont *font;
@end
CustomLabel.m
#import "CustomLabel.h"
#import "Constants.h"
@implementation CustomLabel
@synthesize textColor;
@synthesize backgroundColor;
@synthesize font;
@synthesize shadowColor;
@synthesize shadowOffset;
- (id)initWithFrame:(CGRect)frame {
if ((self = [super initWithFrame:frame])) {
self.textColor = [UIColor whiteColor];
self.backgroundColor = [UIColor clearColor];
self.font = SMALL_CHALKDUSTER;
self.shadowColor = [UIColor colorWithRed:0.0f green:0.0f blue:0.0f alpha:0.35f];
self.shadowOffset = CGSizeMake (0, 2);
self.textAlignment = UITextAlignmentCenter;
return self;
- (void)dealloc {
[super dealloc];
@end
I then allocate a label like so...
ViewController.h
CustomLabel *myLabel;
@property (nonatomic, retain) CustomLabel *myLabel;
ViewController.m
myLabel = [[CustomLabel alloc] init];
myLabel.text = @"Blah blah blah";
I feel like Im way off on this... I must be since it isnt setting any of the properties Im trying to use in the subclass.
I found an older post on the forums here for setting the textAlignment but for some reason I couldnt apply the same logic to mine.
So can anyone help me with this subclass please and thank you?xnav... thanks a ton for pointing me to this link. Its got me closer to my end goal than I was before. Right now I have...
CustomLabel.h
#import <UIKit/UIKit.h>
@interface CustomLabel : UILabel {
@end
CustomLabel.m
#import "CustomLabel.h"
#import "Constants.h"
@implementation CustomLabel
- (void) drawRect:(CGRect)rect {
CGContextRef ctx = UIGraphicsGetCurrentContext();
UIColor *lineColor = [UIColor whiteColor];
UIColor *shColor = [UIColor colorWithRed:0.0f green:0.0f blue:0.0f alpha:0.35f];
//UIColor *bkgColor = [UIColor clearColor];
CGContextSetFillColorWithColor(ctx, lineColor.CGColor);
CGContextSetShadowWithColor(ctx, CGSizeMake(0, 2), self.font.pointSize / 2.0, shColor.CGColor);
//CGRect drawRect = CGRectMake(rect.origin.x, rect.origin.y,rect.size.width, rect.size.height);
//CGContextSetAlpha(ctx, 0) ;
//CGContextFillRect(ctx, drawRect);
//CGContextSetStrokeColorWithColor(ctx, [[UIColor clearColor] CGColor]);
//CGContextSetFillColorWithColor(ctx, [[UIColor clearColor] CGColor]);
CGContextSetBlendMode(ctx, kCGBlendModeClear);
//CGContextAddEllipseInRect(ctx,CGRectMake(size.width-(size.width/2)-(size.width/10), (size.width/10), (size.width/2), (size.height/2)));
//CGContextClosePath(ctx);
//CGContextDrawPath(ctx, kCGPathFillStroke);
//CGContextSetTextDrawingMode(ctx, kCGTextFillStroke);
//self.backgroundColor = [UIColor clearColor];
//[self setBackgroundColor:[UIColor clearColor]];
[self.text drawInRect:self.bounds withFont:TINY_CHALKDUSTER lineBreakMode:self.lineBreakMode alignment:UITextAlignmentCenter];
- (void)dealloc {
[super dealloc];
@end
As you can see I have a couple of things commented out. LOL I still cant figure out how to make the background color clear. I also dont know if I need the dealloc in this subclass. But the other properties seem to be working like the font and line color.
Thanks again for the link and getting me in the right direction xnav. If you can lend any more assistance on how to get that darn background color clear I would appreciate it! -
New computer ~ Help with setting up
Hi everyone, Newbie here!
I am going to set my new computer up tomorrow. The computer I am using at present was installed and set up by someone else so this will be a great learning curve for me. Also I had Infinity installed by the engineer.
Is everything I need to install relating to my broadband available to download? What do I need altogether? I spoke to a BT chap on the phone and he said he would help by remote access. I am a bit nervous of this!
I need to ensure my computer is safe and secure and it all seems technically daunting. Norton security came with my Microsoft Office package. Is this better than McAfee (Net Protect Plus), do I need both? What about a key code scrambler (someone mentioned this to me). As you can see I need reassurance and help arghhhhhhh.
A step by step guide would be great!
Thanks
Solved!
Go to Solution.It is best not to install any of the BT software, just connect your computer to the BT Home hub using an Ethernet cable, or by using the wireless key, if its a wireless connected computers.
See http://bt.custhelp.com/app/answers/detail/a_id/14964/~/getting-started-with-wireless
Using a direct cable connection is best, if you want to get maximum speed.
I would not allow anyone remote access, but if you have no choice, and cannot resolve the issue any other way, then make sure that it is as a direct result of you ringing BT, and not some random person ringing you at home, pretending to be from BT or even Microsoft.
Many people have been caught out by that type of call, and had their computer infected with spyware.
If you already have a trial version of Norton Security, then by all means use it until it expires, then uninstall it.
After that, you have the choice of using the free Microsoft Security Essentials, which is preferred by many forum members, or using BTs Netprotect which is free with some broadband packages. This has been known to make computers run more slowly though.
That is all you need.
If you have any problems, then please return here.
If you have any problems with BT Infinity, then please visit the Infinity board on this forum.
There are some useful help pages here, for BT Broadband customers only, on my personal website.
BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones. -
I need help with this script please ASAP
So I need this to work properly, but when ran and the correct answer is chosen the app quits but when the wrong answer is chosen the app goes on to the next question. I need help with this ASAP, it is due tommorow. Thank you so much for the help if you can.
The script (Sorry if it's a bit long):
#------------Startup-------------
display dialog "Social Studies Exchange Trviva Game by Justin Parzik" buttons {"Take the Quiz", "Cyaaaa"} default button 1
set Lolz to (button returned of the result)
if Lolz is "Cyaaaa" then
killapp()
else if Lolz is "Take the Quiz" then
do shell script "say -v samantha Ok starting in 3…2…1…GO!"
#------------Question 1-----------
display dialog "Around age 11, many boys left their fathers to become…" buttons {"Scholars", "Warriors", "Apprentices"}
set A1 to (button returned of the result)
if A1 is "Apprentices" then
do shell script "say -v samantha Correct Answer"
else
do shell script "say -v samantha Wrong Answer"
#----------Question 2--------
display dialog "Most children were taught
to read so that they could understand the…" buttons {"Music of Mozart", "Bible", "art of cooking"}
set A2 to (button returned of the result)
if A2 is "Bible" then
do shell script "say -v samantha Correct Answer"
else
do shell script "say -v samantha Wrong Answer"
#------------Question 3---------
display dialog "In the 1730s and 1740s, a religious movement called the_______swept through the colonies." buttons {"Glorius Revolution", "Great Awakening", "The Enlightenment"}
set A3 to (button returned of the result)
if A3 is "Great Awakening" then
do shell script "say -v samantha Correct Answer"
else
do shell script "say -v samantha Wrong Answer"
#-----------Question 4--------
display dialog "_______ was
a famous American Enlightenment figure." buttons {"Ben Franklin", "George Washington", "Jesus"}
set A4 to (button returned of the result)
if A4 is "Ben Franklin" then
do shell script "say -v samantha Correct Answer"
else
do shell script "say -v samantha Wrong Answer"
#----------Question 5-------
display dialog "______ ownership gave colonists political rights as well as prosperity." buttons {"Land", "Dog", "Slave"}
set A5 to (button returned of the result)
if A5 is "Land" then
do shell script "say -v samantha Correct Answer"
else
do shell script "say -v samantha Wrong Answer"
#---------Question 6--------
display dialog "The first step toward guaranteeing these rights came in 1215. That
year, a group of English noblemen forced King John to accept the…" buttons {"Declaration of Independence", "Magna Carta", "Constitution"}
set A6 to (button returned of the result)
if A6 is "Magna Carta" then
do shell script "say -v samantha Correct Answer"
else
do shell script "say -v samantha Wrong Answer"
#----------Question 7--------
display dialog "England's cheif lawmaking body was" buttons {"the Senate", "Parliament", "King George"}
set A7 to (button returned of the result)
if A7 is "Parliament" then
do shell script "say -v samantha Correct Answer"
else
do shell script "say -v samantha Wrong Answer"
#--------Question 8-----
display dialog "Pariliament decided to overthrow _______ for not respecting their rights" buttons {"King James II", "King George", "King Elizabeth"}
set A8 to (button returned of the result)
if A8 is "King James II" then
do shell script "say -v samantha Correct Answer"
else
do shell script "say -v samantha Wrong Answer"
#--------Question 9------
display dialog "Parliament named ___ and ___ as England's new monarchs in something called ____." buttons {"William/Mary/Glorius Revolution", "Adam/Eve/Great Awakening", "Johhny/Mr.Laphalm/Burning of the hand ceremony"}
set A9 to (button returned of the result)
if A9 is "William/Mary/Glorius Revolution" then
do shell script "say -v samantha Correct Answer"
else
do shell script "say -v samantha Wrong Answer"
#---------Question 10-----
display dialog "After accepting the throne William and Mary agreed in 1689 to uphold the English Bill of _____." buttons {"Money", "Colonies", "Rights"}
set A10 to (button returned of the result)
if A10 is "Rights" then
do shell script "say -v samantha Correct Answer"
else
do shell script "say -v samantha Wrong Answer"
#---------Question 11------
display dialog "By the late 1600s French explorers had claimed the ___ River Valey" buttons {"Mississippi", "Ohio", "Hudson"}
set A11 to (button returned of the result)
if A11 is "Ohio" then
do shell script "say -v samantha Correct Answer"
else
do shell script "say -v samantha Wrong Answer"
#------Question 12---------
display dialog "______ was sent to ask the French to leave 'English Land'." buttons {"Johhny Tremain", "George Washington", "Paul Revere"}
set A12 to (button returned of the result)
if A12 is "George Washington" then
do shell script "say -v samantha Correct Answer"
else
do shell script "say -v samantha Wrong Answer"
#---------Question 13-------
display dialog "_____ proposed the Albany Plan of Union" buttons {"George Washingon", "Ben Franklin", "John Hancock"}
set A13 to (button returned of the result)
if A13 is "Ben Franklin" then
do shell script "say -v samantha Correct Answer"
else
do shell script "say -v samantha Wrong Answer"
#--------Question 14------
display dialog "The __________ declared that England owned all of North America east of the Mississippi" buttons {"Proclomation of England", "Treaty of Paris", "Pontiac Treaty"}
set A14 to (button returned of the result)
if A14 is "" then
do shell script "say -v samantha Correct Answer"
else
do shell script "say -v samantha Wrong Answer"
#-------Question 15-------
display dialog "Braddock was sent to New England so he could ______" buttons {"Command an attack against French", "Scalp the French", "Kill the colonists"}
set A15 to (button returned of the result)
if A15 is "Command an attack against French" then
do shell script "say -v samantha Correct Answer"
else
do shell script "say -v samantha Wrong Answer"
#------TheLolQuestion-----
display dialog "____ is the name of the teacher who runs this class." buttons {"Mr.White", "Mr.John", "Paul Revere"} default button 1
set LOOL to (button returned of the result)
if LOOL is "Mr.White" then
do shell script "say -v samantha Congratulations…you…have…common…sense"
else
do shell script "say -v alex Do…you…have…eyes?"
#------END------
display dialog "I hope you enjoyed the quiz!" buttons {"I did!", "It was horrible"}
set endmenu to (button returned of the result)
if endmenu is "I did!" then
do shell script "say -v samantha Your awesome"
else
do shell script "say -v alex Go outside and run a lap"
end if
end if
end if
end if
end if
end if
end if
end if
end if
end if
end if
end if
end if
end if
end if
end if
end if
end ifUse code such as:
display dialog "Around age 11, many boys left their fathers to become…" buttons {"Scholars", "Warriors", "Apprentices"}
set A1 to (button returned of the result)
if A1 is "Apprentices" then
do shell script "say -v samantha Correct Answer"
else
do shell script "say -v samantha Wrong Answer"
return
end if
#----------Question 2--------
display dialog "Most children were taught to read so that they could understand the…" buttons {"Music of Mozart", "Bible", "art of cooking"}
set A2 to (button returned of the result)
if A2 is "Bible" then
do shell script "say -v samantha Correct Answer"
else
do shell script "say -v samantha Wrong Answer"
return
end if
(90444) -
Hi, i really need some help with my pictures, I've only got a very basic understanding of how my phone works and have somehow put a load of albums on my phone when i plugged it into the computer-I want to delete some of them off the phone but cannot work out how to do it, when i plug my phone in i can find the photo tab but cannot actually see the pictures and can't see any delete button!!! Please can someone help me, basic explanations would be gratefully recieved xxxx
The photo sync is one way: computer to phone. To remove photos, synced to your phone, remove the check marks next to the albums/folders under the photos tab in itunes & hit the apply/sync button. They will be removed from your phone. You cannot delete photos that were synced to your phone, directly on your phone. The easiest way to manage photos synced to your phone is to create albums or folders on your computer. Move whatever photos you want on your phone into these albums/folders & then select them under the photos tab in itunes to sync to your phone. You can then remove or add photos to these various albums/folders on your computer & the itunes sync process will update your phone every time you sync.
-
Need Help with setting up this Filter
Hi,
I need help making a filter sound like the one used in this youtube song.
I tried setting it up but I've had no success; even though I know for a fact that this filter was made in Logic Pro 9 according to the maker of this song.
I think there might be a bit of 'Fuzz-Wah' in there too but I've never really used that effect so any tips on that would be great, too.
Link: http://www.youtube.com/watch?v=tf017M8SZZE&feature=plcp
Any help with this would be widely appreciated.
Thank you :-)It sounds like a simple hi Q filter sweep to me but getting close to the original synth sound that it is being used on is the challenge. It might well be that it is the filter on the synth itself is what is being swept. Either way, turn up the filter resonance on a band pass filter and sweep it with the lfo or adsr to modulate the filter cutoff if its the synth filter, or automate the filter frequency sweep if you use the channel filter.
Maybe you are looking for
-
How can i make a suggestion on a good update for the iphone
Hi I am Michael Hendrickson a third gen iphone holder. I receintly thought of an idea regarding the "notes" app. Myself and everyone I know uses this app mainly for lists, I feel that it would be in our best intersts to be able to swipe with the fin
-
The touch screen on my nearly brand new Pavillion lap top running windows 8 no longer works.
The touch screen on my nearly brand new Pavillion lap top running windows 8 no longer works. Cant use calibration tools as there's no response to touch. No option in control panal to turn on or off touch capability. I have no computer background s
-
I cant get the wireless printer HP Officejet 6000 to work with my new laptop
I have never been helped by any of these "helps". but **bleep** i'll waste some more time . the wireless printer HP Officejet 2000 is not seen by my new hp laptop Pavilion dv7. I have spent several hours trying to get this to work following all the
-
Auto update of text field on drop down change (binded to XML doc)
Hi all, I have a problem that i'm stuck with since too long and I'll be really grateful for any useful idea. Here is my issue: I have this XML: <?xml version="1.0" encoding="UTF-8"?> <ItemsList> <Product> <itemUnitPrice>
-
Handling events of ActiveX controls in TestStand!rol
Hi, I want to use the Microsoft WINSOCK control with existing ActiveX Automation Adapter of TestStand. These control generates an event in case of incomming data. Question: Is there any way to treat the events of such controls in TestStand (same prob