Higher quality presentation than dvd?

Hello. My sequence will be DV NTSC 720x480. I will be cutting some DVCPRO HD 1080i60 into it but that may not be relevant. This video will be shown in front of many people at an event. Is there a step up, quality-wise, from playing a dvd via a projector? I can rent any equipment I need.
Also, if this video is projected, I read somewhere that projectors use square pixels? If that true? And if so, how to I export the sequence for the event?
Thanks a lot!

My sequence will be DV NTSC 720x480
Since your Sequence will be DV NTSC, you really can't improve over that. So to obtain the best quality feed to the projector, do a print to tape from FCP when you're finished with the edit and playback in a DV VTR or camcorder. A Y/C (S-Video) feed from the playback device will be better than a composite feed, but if you have a DV/DVCam VTR with a component output it would be even better.
That said, what David Bogie Chq-1 said is true. You can get very good results with DVD-Video playback as long as the encoding is handled properly.
-DH
Message was edited by: David Harbsmeier

Similar Messages

How do I achieve a high quality PAL SD DVD from Final Cut Pro?

From a PMW-EX1 camera file edited in Final Cut Pro I am unable to produce a high quality PAL SD DVD using compressor and DVD Studio Pro (tried multiple combinations).
Using Final cut pro and Magic iDVD I can achieve a high quality SD DVD with no changes in export.But am limited to the iDVD restrictions.
From discussions it appears using compressor and DVD Studio pro it is not achievable, it is very frustrating that the Apple product you have to buy is not as efficient as the free one?
If not possible then how do I access the encoded file from IDVD?
My Final cut pro sequence settings:
General - Aspect ratio: HDTV 1080i (16:9) 1920x1080, square and upper(Odd)
Quicktime video settings compressor: xdcam ex 1080i50 (35 mb/s vbr)
I

iDVD does everything automatically for you. With DVDSP and Compressor, all steps must be done correctly. The trade off is that you achieve better quality using Compressor over iDVD.
1. First thing to do is export your sequence as an uncompressed interlaced 25i 720 x 576 16x9 Anamorphic QT.
2. Determine your optimal bitrate by using a bitrate calculator. Here's a good one. Remember you need to account for all video on the disc, including motion menus.
http://www.videohelp.com/calc.htm
3. Bring your down converted QT into Compressor and use the manual settings set your bitrate. Also encode out a Dolby digital AC3 file. These files take up less bandwidth than uncompressed audio. Also remember to match your upper fiiled dominate filed order as well in Compressor. This must be consistent throughout the export and encoding stages.
4. bring your encoded video and audio files into DVDSP and author

Need High quality fla to dvd playable file converter

Hi,
I'm making a project in swf which has got audio, video and images. I need to release this project in flash format and DVD format also.
Could anyone suggest me any High quality fla to dvd converter ? I just used trial versions of Moyea and few others before deciding to buy but they don't convert in high quality.
Even if they do, The file size becomes really too big. For instance just a 10 mb file becomes 4 gb.
Please suggest some good converters.
Thanks.

Did you render the Timeline fully?
Just so you'll know, the Viewer in FCE/FCP is just that; a viewer that shows the image at it's native resolution. The Canvas (and Firewire output) shows the image at the Sequence resolution - not the original resolution of the image.
If you're not going to be pushing in to (zooming in) the image, you should resize the images so they're close to your Sequence resolution. For example, if you're working in an NTSC DV Sequence, the resolution will be 720x480 (rectangular pixels). If your images are much larger than that, it may be part of the problem.
-DH

How to export a complex Keynote to high quality video for DVD?

I have had dozens of attempts to turn a complex Keynote into a high quality video.
Either they turn out disappointiingly way low res
or they are very choppy with half the transitions gone
or they Cannot make the video at all
HELP.
I need to turn this project in to my client today.

If you use the DVD export in Keynote 3 with a self playing movie, the quality will be fine...just don't trust what you see on your mac screen, play it on a DVD player to check the quality. I did a test a while back and it was only the pauses that looked bad.
Read about it here:
http://www.keynoteuser.com/news/?p=135
pay close attention to what I complain about...it's just the slide pauses, not the normal motion playback, which means selfplaying stuff looks pretty decent (though never as good as the original, but that's the fault of the DVD format, not Apple).

HT4914 What happens with my higher quality songs than itunes can offer?

I have songs higher than 256 kbps, some in mp3 320 kbps and other in ALAC format, what’s going to happen to these songs? Will I be downgraded to iTunes quality?

Nothing will happen to them. Keep them backed up so that you will still have copies if your hard drive fails.
What has caused a lot of discussion, and may be the basis of your question, is the iTunes Match capability. It is an optional feature, so it will not do anything unless you sign up for it. If you do sign up for it, your MP3/320 and ALAC songs will be backed up as AAC/256 copies, which as you correctly note, is a downgrade to the audio quality.
For that reason, iTunes Match is not recommended for your situation.

I want high quality SD for DVD

alright, i've got a 1.1 gig video about 5 minutes long that is in the .mov format (raw out of fcp). I'll let you know what I have already done and if you could, please let me know where I could improve. I took the .mov video and put it in compressor. Told it to convert to mpeg-2 and make a 2-pass VBR best quality. After being compressed, I dropped the .m2v video and dolby soundtrack into dvd studio pro and burned the baby. Looks pretty good, anything I should do to make it even clearer?

Check out this site:
http://osxdaily.com/2012/04/22/format-drive-mac-pc-compatible/
That will show you how to format a USB stick for use on both PC and Mac.
If the problem continues take it to an Apple store and have them check it out.
>Also what s exFAT?<
From:
http://en.wikipedia.org/wiki/ExFAT
"exFAT (Extended File Allocation Table) is a Microsoft file system optimized for flash drives.[3] It is proprietary and patented."
That first site explains it at length.

I recored a dancing video, and I edited it on IMovie (Mac OS X 10.6.8)) and it won't let finalize it into a higher quality other than the mobile quality .. HELP ??!!!

HELP !

Hi
Frist thought is - is there enough free space on Your start-up Hard disk ?
If you got more than 25gb then the problem is elsewhere - as
- trash the iMovie pref filé
- repair permissions
- repair Hard disk
Yours Bengt W

What Is The Best Way To Connect Ipod To Stereo Reciever With High Quality?

I recently purchased an 80 gig and am a newbie. I ripped all my music at around 280kbps to retain good audio quality when playing in my car and home theatre system. There are tons of accesories out there (docks, jacks, etc) which is the highest quality to connect my Yamaha receiver. I would think a connection to the bottom of my ipod would be of a higher quality rather than using the headphone jack. Any suggestions would be great. I was thinking about using the monster itv link but mostly for audio. thanks

OK - So now that you have all completely ignored the original question - in hopes of proving your manly-hood....
Does anyone have an answer to the original question....
"What is the best way to connect to a high end home stereo to retain the best sound?"
For sure any connection going through the headphone jack will be a big step back - enough so that you would easily hear a sound quality loss in doing so.
For the few of you who would like to argue/bicker/rant on the nominal sound quality loss....keep on doing so, but for those who actually have some respectable advice we would love to hear it.
For the record, I tend to hear just outside the normal human auditory range...
To help myself put it to rest already... a few years back I decided to conduct my own little listening test.
I took 6 different common ripping modalities (from lossless - to - 128kbps in both MP3 & AAC.... then transfered all of them in order to a blank. Used the same song for each - the song chosen opened with a few clean crisp bars of high freq. music, followed by an instant explosion/drop into a tight & low bassline.
The final cutoff that was achieved before I was unable to detect an audible difference was 198 VBR AAC. Having convinced myself that there was the ever sooooooo slight difference b/t 198 & 256, I went with my current ripping status of 256.... Just incase my audible range should become finally honed with age (yeah, like that is really going to happen) !
This test was run over a Yamaha DSP receiver, running at a constant 110w per channel (w/a max of 220w). The speaker setup was a full surround set of Klipsch Reference Series..... each speaker housing 2 x 6.5 woofer (each housing 2 x 1" Titanium tweeters) And sitting along side the 5 surrounds was/is a 150w continuous 12in. Subwoofer.
Now I am hardly stating that I have hearing as good as some of you extremely technically profound music enthusiasts out there, but for the majority of people making comments about sound quality, and lack there of - when played over a $120/40w Audiovox radio.... I'm sorry, but I would have to side on that of......"Hogwash, that you can hear a difference!"
So.... if possible would someone please offer some advice on a dock or cable connection that will allow us to enjoy the music we ripped at whatever
so-called range we did!
For those interested in seeing who could hit the further bullseye with their eyes closed, You win!!! Now can you help us?
MBP Mac OS X (10.4.9)

Higher quality mp3?

Is there anyway to get a higher quality mp3 than 128 when buying from the ITunes Music Store? I've set my software to convert at 190, but it doesn't do it on things i buy?
reply to [email protected]
Thanx

The Music Store downloads are currently only available in protected AAC (MP4) 128 kbps format. Because they are DRM protected, to get them to anything else you have to burn them to an audio CD first then import that CD back into iTunes in the format of your choice. It's inevitable however that you'll lose quality as you'll now have a copy two generations from the original.

JAI - Creating High Quality thumbnails

I am using JAI to take in large images and proportionally resize it to around ~300 x 220 image.
Using the "scale" returns horrible quality
ParameterBlock pb2 = new ParameterBlock();
pb2.addSource( src );
pb2.add( scale );
pb2.add( scale );
pb2.add( 0.0f );
pb2.add( 0.0f );
JAI.create( "scale", pb2, null );Using "subsampleaverage" is much better, but still returns worse quality than the original.
ParameterBlock pb2 = new ParameterBlock();
pb2.addSource( src ); // The source image
pb2.add( ( double ) scale ); // The xScale
pb2.add( ( double ) scale ); // The yScale
pb2.add( new InterpolationBicubic2(8) ); // The interpolation...I Tried all Interpolation Types already
JAI.create( "subsampleaverage", pb2, null );I want an exact quality copy of the original. Is there a way to do this in JAI?

I mean in photoshop it saves much clearer (higher
quality image) than through JAI. I know in Photoshop
you can choose clarity on a scale from 1 to 12 when
saving image files for the web. The only thing I see
in JAI is interpolation which provides 3 or 4 choices.Ah, you mean the JPEG codec quality level. JAI's JPEGTileCodecDescriptor has a quality resource:
"A factor that relates to the desired tradeoff between image quality and the image data compression ratio. The range of this parameter is from 0.0 to 1.0. A setting of 1.0 produces the highest quality image at a lower compression rate. A setting of 0.0 produces the highest compression ratio, with a sacrifice to image quality. The default value is 0.75."

I've reduced my project size to "high quality," with a resulting 2.42GB size and 78 minutes project time. With my 4.7GB dvd, I should now have more than sufficient space, but I still get 'Your project exceeds the maximum content duration."

Am I simply out of luck? The video itself is 65 minutes with pretty simple music and photos in the themes with no scene selection option.
Thanks.

iDVD is not concerned with size, just length.
iDVD encoding settings:
http://support.apple.com/kb/HT1502?viewlocale=en_US
Short version:
Best Performance is for videos of up to 60 minutes
Best Quality is for videos of up to 120 minutes
Professional Quality is also for up to 120 minutes but even higher quality (and takes much longer)
That was for single-layer DVDs. Double these numbers for dual-layer DVDs.
Professional Quality: The Professional Quality option uses advanced two-pass technology to encode your video (The first pass determines which parts of the movie can be given greater compresson without quality loss and which parts can’t. The second pass then encodes those different parts accordingly) , resulting in the best quality of video possible on your burned DVD. You can select this option regardless of your project’s duration (up to 2 hours of video for a single-layer disc and 4 hours for a double-layer disc). Because Professional Quality encoding is time-consuming (requiring about twice as much time to encode a project as the High Quality option, for example) choose it only if you are not concerned about the time taken.
In both cases the maximum length includes titles, transitions and effects etc. Allow about 15 minutes for these.
You can use the amount of video in your project as a rough determination of which method to choose. If your project has an hour or less of video (for a single-layer disc), choose Best Performance. If it has between 1 and 2 hours of video (for a single-layer disc), choose High Quality. If you want the best possible encoding quality for projects that are up to 2 hours (for a single-layer disc), choose Professional Quality. This option takes about twice as long as the High Quality option, so select it only if time is not an issue for you.
Use the Capacity meter in the Project Info window (choose Project > Project Info) to determine how many minutes of video your project contains.
NOTE: With the Best Performance setting, you can turn background encoding off by choosing Advanced > “Encode in Background.” The checkmark is removed to show it’s no longer selected. Turning off background encoding can help performance if your system seems sluggish.
And whilst checking these settings in iDVD Preferences, make sure that the settings for NTSC/PAL and DV/DV Widescreen are also what you want.
http://support.apple.com/kb/HT1502?viewlocale=en_US

Low quality DVD outcome.. need help for high quality result ASAP!

Hi every 1,
(This is my first post, as I only got my iMac 2 weeks ago.. so please be gentle with me :P )
I have just been asked to turn a Microsoft powerpoint (PPT) into a DVD for "induction training video" purposes with voice overs and backing music. I have a professional music studio so providing high quality audio is fine, but trying to turn the power point into a high quality DVD file is my problem. This powerpoint has timing transitions (fade ins etc) for the timing of voice gaps. When using Microsoft PPT, you can turn the PPT into a Quicktime file which I was going to drop into iMoive then add the music and voiceovers.. this is when my problems started. Microsofts powerpoint doesn't add the transtiions and effect into render Quicktime movie, so I thought as my new iMac has iWork (KEYNOTE) I'd give it a try and to my surprise it all worked and the final mpeg4 quicktime movie result work great _when you look at it on the MAC_.
1) Problem
I then exported the file into iMovie and then my first Problem arose.... (grr). I movie lost it's sharpness and the images started to have pixelation.. that seemed to pulse in 1 seconds gaps.
I hope this was just an issue with the iMovie preview window and thought once I put it into iDVD and burnt it... the final result may be fine.. but I was wrong and the quality was crap... with the pixelation still there.
2) Problem
The other problem that came up was the about 25% of the edge of the total screen was cutoff. When i did the original file, I choose 4:3 ratio, and watched it on this..so where did the image size go wrong.. I also choose the "high quality" Quicktime file, but didn't go into the settings in the iMovie in the export section (which I should off), but after check the compression type was H.264.. and I also didn't change any settings in the 'export file' section in KEYNOTE.. this is where I think I must have gone wrong..
So in closing. my questions is:
-What's the best way to turn a PPT into a _high quality file_ so it looks professional once it goes through iMovie and iDVD.. or
- Should I just redo the whole production using iMovie ( by re doing all the work eg wording, transistion inside iMovie seems like a lot of extra word ) and so not use the PPT at all... and if I do this, then
- What's sizes, and ratio and compressions should I use for 4:3 ratio TV purpose (eg. whats size should a background image be that I do inside Photoshop, so I can put the transition wording over the top, so I see it on the TV screen and the edge doesn't get cutoff etc.?
I was very impressed with Keynote and would be happy to use this for most of the production.. but am I banging my head againist a wall...re fixing quality problems when exporting files into... can someone shed some light on this for me?
Sorry this is such a big post.. but I thought if I gave you most of the background you would have to ask so many questions.
Look forward to any help any 1 can provide..
Michael
Message was edited by: sycosingo

Matti,
Thx so much for your help.. it's really appreciated. This is by far the best result quality wise, (but I really am a perfectionist and personally are still not overall happy with the final product) but if my client is happy.. then I will continue down this track for this job.
ie Create TIFF;'s>Quicktime PRO>iMovie (transistions)>iDvd
You've been a great help and I hope it good enough for the client.
I find the images and wording lose their sharpness only after being imported into iMoive. I could still be probably enhance the quality level of the TIFF's once more, as I did the test slides in Keynote, then exported the 5 slides a individual as TIFFS out of Keynote, then imported the into QuickTime Pro as you suggested then followed your instructions all the way to the final burning of the CD. I also tried doing this in Photoshop using your suggestion of 720x576 images (for PAL) .. pixel aspect ratio to ~1.094 so you can see the correct proportions for 4:3 video output. When creating the new slide in Photoshop there were a few extra settings other than the ones you gave me... _so I would real appreciate what every setting should be when creating the NEW TIFF file in Photoshop for PAL 4:3._ I noticed when I did this the image crispness on the fonts was shithouse pixelated and shadows, even while looking at it from inside Photoshop )
As I tried mutliple ways of importing into iMovie (yours being the best suggestion) I really believe when dragging a TIFF or movie turns to blur on the way into iMoive. You can see the image is blurred from that point on.... _do I need to buy final cut pro or express to get a better image quality result?_
I also tried iMoive7, which I found was great to use video editing wise, but Apples has definitely stuffed up there by not give users a 'time line' to work with in the Audio section... but everything else in the video area was great to use.., but in my situation trying to line up the narration to slide, while having also background music is now impossible sadly.
Also I really like the 3D transitions in KEYNOTE, plus iMovie 7.. do you know if there are available for HD6 or if there's a 3rd party company that has smilar versions
Thx again,
sycosingo
Message was edited by: sycosingo

Better than DVD-quality on .mac - but which size?

Hi, that was what Steve Jobs said that there is the possibility to have better than DVD-quality movies on .mac Is this only with HD-cameras and material because they can´t be burnt at that resolution onto a DVD? Or is it also true with standard cameras? And which file sizes are we are going to expect while up- and downloading such movies? Are they even playable for the average internet user?
Thanks in advance for clarifying - Christoph

Steve may have left out the word "current" when he mentioned better quality than a DVD.
DVD's (currently) use MPEG-2 format and only the newest players can handle high definition.
Your Web based files can use high definition formats. Just like those HD trailers at http://apple.com/trailers
You can also publish larger dimension SD video.
Obviously the file size of these larger dimensions would require a fast Internet connection and a very patient viewer.

What's the proper workflow to combine multiple video types and turn them into one high quality DVD?

I'm trying to combine 1080i (29.97fps), 1080p (29.97fps), and 720p (24fps) video files into a single Premiere Pro project, and end up with a high quality DVD.
There are a few problems I can't solve:
1. There seems to be interlacing and clarity issues any time I export it to DVD dimensions (720x480), and on some TVs I'll get a bouncing motion on the 720p footage (slideshow). Yet everything seems to look perfect when I export it something like an HD MOV file.
2. If I use Final Cut X to make the DVD, I'll get audio popping and decent image quality. Yet if I use Encore, I'll get horrible interlacing, but good audio.
I don't have any training in video workflow let alone how to properly diagnose and solve problems that arise. So I need someone to lay out the proper workflow and settings from start to finish to get these three different types of footage to look great on a DVD using Premiere/Encore.
I've attached sample images showing the types of footage I'm using and the kind of problems I'm running into for reference.

By far the best way to get the quality of encoding is to use Compressor and not DVDSP. You can set Compressor up to do the AC3 (which DVDSP can't do). Alternatively, use a better encoder than Compressor, such as BitVice or MegaPEG.X... but remember that these do not do AC3 encoding.
Keep the encoded assets all in a single folder on your mac, then drag that folder into the DVDSP 'Assets' tab. This will import them all and keep them in the folder, which is a neater way of doing things. Select all of the clips within the folder (or simply select the folder itself) and drag them on to the track - they will go on in alphabetic or numeric order (whichever you have used as your names). If using numbers, remember to use '01', '02', etc otherwise clip ten, eleven, twelve and so on will follow clip one... clip two will come after clip 19.
Drop them all on a single track. You can then point a menu button at the track and all of the clips will play one after the other. If you want black in between then you will be better adding this in a NLE such as Final Cut, then exporting the entire sequence of clips as a single file. Alternatively, create a black .pict file the correct dimensions for the video format you are using and manually add it in between each clip on the timeline. Or, create a series of black .pict files and name them 011, 021, 031 and so on. Place them in your folder of clips with the MPEGs named 01, 02 and so on. When you select all and drop it onto your timeline within DVDSP a black clip will go in between each piece of footage (sequence will be 01, 011, 02, 021, 03, 031 ). This is probably the quickest way to do it. You can reuse the same black .pict files for every project like this and as long as you follow the same naming convention it will always work.
Like anything you want to automate, the first couple of times take longer to set up. After that it is a lot easier.

How Can I Make a High Quality HD DVD Video (dvd vob)

i work a hd project and after we will make a dvd video. if i export a mov and convert it with toast titanium the quality is bad. if i make it dvd studio pro hd dvd mac and pc is open but dvd player does not play it. and the other version dvd studio pro convert from 16/9 to 4/3. but i don't like it. the other one i send to compressor and chose the dvd/hd dvd:mpeg-2 30 minutes it exports mv2 not vob(audio ts video ts)
so i want to make a high quality hd dvd video how can i do that?
thanks
Message was edited by: rec_off
Message was edited by: rec_off

I don't know about NTSC but there is a nice PAL solution for SD 16:9 for ordinary DVDs. The 16:9 image becomes 720x576 pixels. So the pixels are each quite wide, and the horizontal resolution is less than the vertical resolution, but at least no pixels are wasted as with letterbox.
A semi-solution is to make a HD-DVD. That format has been abandoned but Apple software pretends otherwise. Apple Compressor does compressions at around 20 Megabits/second data rate specifically for HD-DVD, and Apple DVD Studio Pro makes HD-DVDs. For short projects, less than around 30 minutes, the HD-DVD can be made on a normal DVD. (I did this for a 40 minute project by cutting the bitrate somewhat.) The quality is almost equal to Blu-Ray, but who can play it? People with well equipped Apples can.

Higher quality presentation than dvd?

Similar Messages

Maybe you are looking for