HighErrorRate caused by the giants on VSL link
Hi,
We are running into the Bug CSCsc61302: the giant packet counters on VSL interfaces increment in Catalyst 6500 VSS. It is an expected behavior, but we were paged up by CiscoWorks (LMS3.2) due to HighErrorRate (55~60%) at 2AM every morning.
We currently have dot3StatsEntry.13 excluded from SNMP view to supress the pages. But we loss the ability to monitor the giants alert caused by other unexpected behaviors because of it. Is there anyway that we can supress the error alerts caused by this VSL Giants and get all other interface error features properly monitored?
Thanks.
No. Other giants would be counted by the same object, so there is no way to differentiate giants caused by the bug vs. other giants. It really looks like you've employed the best available workaround. Filtering dot3StatsFrameTooLongs will remove giants from the error calculation, leaving other others visible.
Similar Messages
-
Hi Guys,
I have a head scratcher that I'm dealing with. I have 2x (2 month) 6880-x switches configured with vss with 2 vsl links on each of its sup cards and switch 1 is the active switch on the vss. Both 6880x chassis also have 2 additional 10g modules each. I am dealing with 2 issues in this setup.
The first issue is, i have a 3750x with a 10g module thats port channeled to the vss with one 10g link going to each of the chassis. Within the first 3 days it started dropping the link that's plugged to switch1, then comes back on right away. It does it randomly throughout the day. I have changed out the optics on both ends, changed the cable, and also changed the module on the 3750x and I still get the same issue. The strange part is that when switch2 on the vss becomes the active switch, the problem goes away. I did notice this before changing out the optics, cable, module on the 3750x.
The second issue is the one I'm been trying to figure out along with cisco TAC. This started about a month after bring the vss online. When switch1 was the active switch in the vss, every couple of days vsl links drop one at a time, eventually killing the vss and putting the standby unit into recovery mode because of the dual active detection. once I reboot the standby switch, the vss comes back up normally. it did this a couple of times until I decided to force switch2 to be the active switch on the vss. when switch2 became active, the vss was stable for about a month then the vsl links died again, and the system failed over to switch1. after looking at the logs with cisco tac, we see that the vsl links stop responding which causes the failover, but up until now we still can't determine what is causing the vsl links to fail. cisco tac said that maybe the vsl links were being overloaded but we have been monitoring the bandwidth utilization on the vsl links and they never go beyond 1% utilization. The last suggestion by cisco tac was to add another vsl link but through another module other than the sup. This was done a couple of days ago so now i'm waiting to see if the vsl links fail again and since switch1 is the active switch on the vss, i'm having to deal with the first issue above with the 3750x.
I've included some log entries from the dropped port-channel member and also logs for when the vsl links fail.
Logs for 3750x port-channel member drops.
*Jul 5 05:27:10 PDT: %LINEPROTO-SW1-5-UPDOWN: Line protocol on Interface TenGigabitEthernet2/2/5, changed state to down
*Jul 5 05:27:10 PDT: %LINK-SW1-3-UPDOWN: Interface TenGigabitEthernet2/2/5, changed state to down
*Jul 5 05:27:10 PDT: %LINK-SW1-3-UPDOWN: Interface TenGigabitEthernet2/2/5, changed state to up
*Jul 5 05:28:10 PDT: %LINEPROTO-SW1-5-UPDOWN: Line protocol on Interface TenGigabitEthernet2/2/5, changed state to up
*Jul 6 11:28:52 PDT: %LINEPROTO-SW1-5-UPDOWN: Line protocol on Interface TenGigabitEthernet2/2/5, changed state to down
*Jul 6 11:28:52 PDT: %LINK-SW1-3-UPDOWN: Interface TenGigabitEthernet2/2/5, changed state to down
*Jul 6 11:28:53 PDT: %LINK-SW1-3-UPDOWN: Interface TenGigabitEthernet2/2/5, changed state to up
*Jul 6 11:29:53 PDT: %LINEPROTO-SW1-5-UPDOWN: Line protocol on Interface TenGigabitEthernet2/2/5, changed state to up
*Jul 7 06:27:25 PDT: %LINEPROTO-SW1-5-UPDOWN: Line protocol on Interface TenGigabitEthernet2/2/5, changed state to down
*Jul 7 06:27:25 PDT: %LINK-SW1-3-UPDOWN: Interface TenGigabitEthernet2/2/5, changed state to down
*Jul 7 06:27:26 PDT: %LINK-SW1-3-UPDOWN: Interface TenGigabitEthernet2/2/5, changed state to up
*Jul 7 06:27:33 PDT: %LINEPROTO-SW1-5-UPDOWN: Line protocol on Interface TenGigabitEthernet2/2/5, changed state to up
*Jul 7 06:33:43 PDT: %LINEPROTO-SW1-5-UPDOWN: Line protocol on Interface TenGigabitEthernet2/2/5, changed state to down
*Jul 7 06:33:43 PDT: %LINK-SW1-3-UPDOWN: Interface TenGigabitEthernet2/2/5, changed state to down
*Jul 7 06:33:43 PDT: %LINK-SW1-3-UPDOWN: Interface TenGigabitEthernet2/2/5, changed state to up
*Jul 7 06:34:43 PDT: %LINEPROTO-SW1-5-UPDOWN: Line protocol on Interface TenGigabitEthernet2/2/5, changed state to up
*Jul 7 07:38:35 PDT: %LINEPROTO-SW1-5-UPDOWN: Line protocol on Interface TenGigabitEthernet2/2/5, changed state to down
*Jul 7 07:38:35 PDT: %LINK-SW1-3-UPDOWN: Interface TenGigabitEthernet2/2/5, changed state to down
*Jul 7 07:38:36 PDT: %LINK-SW1-3-UPDOWN: Interface TenGigabitEthernet2/2/5, changed state to up
log for VSL link failures
*Jun 27 23:59:25 PDT: %VSLP-SW2-3-VSLP_LMP_FAIL_REASON: Te2/5/15: Link down
*Jun 27 23:59:25 PDT: %VSL-SW2-5-VSL_CNTRL_LINK: New VSL Control Link 2/5/16
*Jun 27 23:59:25 PDT: %LINEPROTO-SW2-5-UPDOWN: Line protocol on Interface TenGigabitEthernet2/5/15, changed state to down
*Jun 27 23:59:25 PDT: %LINEPROTO-SW2-5-UPDOWN: Line protocol on Interface TenGigabitEthernet1/5/15, changed state to down
*Jun 27 23:59:25 PDT: %LINK-SW2-3-UPDOWN: Interface TenGigabitEthernet2/5/15, changed state to down
*Jun 27 23:59:25 PDT: %VSLP-SW2-3-VSLP_LMP_FAIL_REASON: Te2/5/16: Link down
*Jun 27 23:59:25 PDT: %VSLP-SW2-2-VSL_DOWN: Last VSL interface Te2/5/16 went down
*Jun 27 23:59:25 PDT: %VSLP-SW2-2-VSL_DOWN: All VSL links went down while switch is in ACTIVE role
*Jun 27 23:59:25 PDT: %LINEPROTO-SW2-5-UPDOWN: Line protocol on Interface TenGigabitEthernet2/5/16, changed state to down
*Jun 27 23:59:25 PDT: %LINEPROTO-SW2-5-UPDOWN: Line protocol on Interface Port-channel2, changed state to down
*Jun 27 23:59:25 PDT: %LINK-SW2-3-UPDOWN: Interface Port-channel2, changed state to down
*Jun 27 23:59:25 PDT: %LINK-SW2-3-UPDOWN: Interface TenGigabitEthernet2/5/16, changed state to down
*Jun 27 23:59:25 PDT: %LINEPROTO-SW2-5-UPDOWN: Line protocol on Interface Port-channel1, changed state to down
*Jun 27 23:59:25 PDT: %LINK-SW2-3-UPDOWN: Interface Port-channel1, changed state to down
*Jun 27 23:59:25 PDT: %OIR-SW2-6-INSREM: Switch 1 Physical Slot 5 - Module Type LINE_CARD removed
*Jun 27 23:59:25 PDT: %OSPF-SW2-5-ADJCHG: Process 1, Nbr 10.253.0.3 on TenGigabitEthernet1/1/1 from FULL to DOWN, Neighbor Down: Interface down or detached
*Jun 27 23:59:25 PDT: %LINEPROTO-SW2-5-UPDOWN: Line protocol on Interface Port-channel24, changed state to down
*Jun 27 23:59:25 PDT: %LINK-SW2-3-UPDOWN: Interface Port-channel24, changed state to down
*Jun 27 23:59:26 PDT: %OIR-SW2-6-INSREM: Switch 1 Physical Slot 1 - Module Type LINE_CARD removed
*Jun 27 23:59:26 PDT: %LINK-SW2-3-UPDOWN: Interface Port-channel17, changed state to down
*Jun 27 23:59:26 PDT: %PFREDUN-SW2-6-ACTIVE: Standby processor removed or reloaded, changing to Simplex mode
*Jun 27 23:59:26 PDT: %OIR-SW2-6-INSREM: Switch 1 Physical Slot 2 - Module Type LINE_CARD removed
*Jun 27 23:59:27 PDT: %LINK-SW2-3-UPDOWN: Interface TenGigabitEthernet1/5/14, changed state to down
*Jun 27 23:59:27 PDT: %LINK-SW2-3-UPDOWN: Interface TenGigabitEthernet1/5/15, changed state to down
*Jun 27 23:59:27 PDT: %LINK-SW2-3-UPDOWN: Interface TenGigabitEthernet1/5/16, changed state to down
*Jun 27 23:59:27 PDT: %LINEPROTO-SW2-5-UPDOWN: Line protocol on Interface TenGigabitEthernet1/5/14, changed state to down
*Jun 27 23:59:27 PDT: %LINEPROTO-SW2-5-UPDOWN: Line protocol on Interface TenGigabitEthernet1/5/16, changed state to down
*Jun 27 23:59:27 PDT: %LINK-SW2-3-UPDOWN: Interface TenGigabitEthernet1/1/1, changed state to down
*Jun 27 23:59:27 PDT: %LINK-SW2-3-UPDOWN: Interface TenGigabitEthernet1/1/2, changed state to down
*Jun 27 23:59:27 PDT: %LINK-SW2-3-UPDOWN: Interface TenGigabitEthernet1/1/3, changed state to down
*Jun 27 23:59:27 PDT: %LINEPROTO-SW2-5-UPDOWN: Line protocol on Interface TenGigabitEthernet1/1/1, changed state to down
*Jun 27 23:59:27 PDT: %LINEPROTO-SW2-5-UPDOWN: Line protocol on Interface TenGigabitEthernet1/1/2, changed state to down
*Jun 27 23:59:27 PDT: %LINEPROTO-SW2-5-UPDOWN: Line protocol on Interface TenGigabitEthernet1/1/3, changed state to down
Press RETURN to get started!
*Jun 28 07:03:33.421: %USBFLASH-SW2_STBY-5-CHANGE: bootdisk has been inserted!
*Jun 28 07:03:53.297: %OIR-SW2_STBY-6-INSPS: Power supply inserted in slot 1
*Jun 28 07:03:53.301: %C6KPWR-SW2_STBY-4-PSOK: power supply 1 turned on.
*Jun 28 07:04:26.093: %FABRIC-SW2_STBY-5-FABRIC_MODULE_ACTIVE: The Switch Fabric Module in slot 5 became active.
*Jun 28 07:04:48.497: %DIAG-SW2_STBY-6-RUN_MINIMUM: Switch 2 Module 5: Running Minimal Diagnostics...
*Jun 28 07:04:48.497: %CONST_DIAG-SW2_STBY-6-DIAG_PORT_SKIPPED: Module 5 port 15 is skipped in TestLoopback due to: the port is used as a VSL link.
*Jun 28 07:04:48.497: %CONST_DIAG-SW2_STBY-6-DIAG_PORT_SKIPPED: Module 5 port 16 is skipped in TestLoopback due to: the port is used as a VSL link.
*Jun 28 07:04:55.049: %CONST_DIAG-SW2_STBY-6-DIAG_PORT_SKIPPED: Module 5 port 15 is skipped in TestFexModeLoopback due to: the port is used as a VSL link.
*Jun 28 07:04:55.049: %CONST_DIAG-SW2_STBY-6-DIAG_PORT_SKIPPED: Module 5 port 16 is skipped in TestFexModeLoopback due to: the port is used as a VSL link.
*Jun 28 07:05:00.165: %CONST_DIAG-SW2_STBY-6-DIAG_PORT_SKIPPED: Module 5 port 15 is skipped in TestL2CTSLoopback due to: the port is used as a VSL link.
*Jun 28 07:05:00.165: %CONST_DIAG-SW2_STBY-6-DIAG_PORT_SKIPPED: Module 5 port 16 is skipped in TestL2CTSLoopback due to: the port is used as a VSL link.
*Jun 28 07:05:06.049: %CONST_DIAG-SW2_STBY-6-DIAG_PORT_SKIPPED: Module 5 port 15 is skipped in TestL3CTSLoopback due to: the port is used as a VSL link.
*Jun 28 07:05:06.049: %CONST_DIAG-SW2_STBY-6-DIAG_PORT_SKIPPED: Module 5 port 16 is skipped in TestL3CTSLoopback due to: the port is used as a VSL link.
*Jun 28 07:05:23.309: %DIAG-SW2_STBY-6-DIAG_OK: Switch 2 Module 5: Passed Online Diagnostics
*Jun 28 00:05:38 PDT: %SYS-SW2_STBY-6-CLOCKUPDATE: System clock has been updated from 00:05:38 PDT Sat Jun 28 2014 to 00:05:38 PDT Sat Jun 28 2014, configured from console by console.
*Jun 28 00:05:38 PDT: %SYS-SW2_STBY-6-CLOCKUPDATE: System clock has been updated from 00:05:38 PDT Sat Jun 28 2014 to 00:05:38 PDT Sat Jun 28 2014, configured from console by console.
*Jun 28 00:05:38 PDT: %SSH-SW2_STBY-5-DISABLED: SSH 2.0 has been disabled
*Jun 28 00:05:54 PDT: %SYS-SW2_STBY-5-RESTART: System restarted --
Cisco IOS Software, c6880x Software (c6880x-ADVENTERPRISEK9-M), Version 15.1(2)SY2, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Wed 26-Feb-14 15:30 by prod_rel_team
*Jun 28 00:05:54 PDT: %SSH-SW2_STBY-5-ENABLED: SSH 2.0 has been enabled
*Jun 28 00:05:54 PDT: %SYS-SW2_STBY-3-LOGGER_FLUSHED: System was paused for 00:03:01 to ensure console debugging output.
*Jun 28 00:05:56 PDT: %C6KENV-SW2_STBY-4-LOWER_SLOT_EMPTY: The lower adjacent slot of module 5 might be empty. Airdam must be installed in that slot to be NEBS compliant
*Jun 28 00:07:36 PDT: %DIAG-SW2_STBY-6-RUN_MINIMUM: Switch 2 Module 1: Running Minimal Diagnostics...
*Jun 28 00:07:37 PDT: %SYS-SW2_STBY-3-LOGGER_FLUSHED: System was paused for 00:01:29 to ensure console debugging output.
*Jun 28 00:07:41 PDT: %DIAG-SW2_STBY-6-RUN_MINIMUM: Switch 2 Module 2: Running Minimal Diagnostics...
*Jun 28 00:08:10 PDT: %DIAG-SW2_STBY-6-DIAG_OK: Switch 2 Module 1: Passed Online Diagnostics
*Jun 28 00:08:22 PDT: %EC-SW2_STBY-5-CANNOT_BUNDLE2: Te2/1/10 is not compatible with Te1/2/10 and will be suspended (Operational flow control send of Te2/1/10 is off, Te1/2/10 is on)
*Jun 28 00:08:31 PDT: %EC-SW2_STBY-5-COMPATIBLE: Te2/1/10 is compatible with port-channel members
*Jun 28 00:08:45 PDT: %DIAG-SW2_STBY-6-DIAG_OK: Switch 2 Module 2: Passed Online Diagnostics
*Jun 28 00:08:46 PDT: %C6KENV-SW2_STBY-4-HIGHER_SLOT_EMPTY: The higher adjacent slot of module 2 might be empty. Airdam must be installed in that slot to be NEBS compliant
ELDC1C1-AG01-1 line 0
************************ W A R N I N G ***************************
* THIS IS A PRIVATE COMPUTER SYSTEM, AND FOR AUTHORIZED USE ONLY.*
* THIS SYSTEM IS MONITORED, AND ANY UNAUTHORIZED USE MAY BE *
* SUBJECT TO CRIMINAL PROSECUTION. *
* IF YOU ARE NOT AUTHORIZED, LOG OUT IMMEDIATELY!!!!! *
so according to the logs, it seems like the switch was reloaded or something of the nature but even the cisco tac said that it wasnt the case but couldnt determine whats causing it either. Tac went through the config on the vss and has said that its configured correctly.
Maybe someone else has experienced this issue or if someone can point out something that I can look at... sorry for the very long post.
thanksI suppose, we have the same problem. Only when Switch 1 is the active switch of the 6880-X VSS system, the connection to the FEX-stack breaks suddenly after running fine for some days and the FEX-stack (3 x 6800-IA) get only ready again when I reset the whole VSS-system, both VSS-switches and the FEX-stack.
All access ports at the FEX can't connect to our infrastructure (DHCP,DNS...). The two connected TenG FEX-stack uplinks sometimes get down and sometimes only the uplink to the active parent switch get down. The SYST LED of FEX 1 lighting amber.
When parent switch 2 is the active unit the issue never occured.
6880-X running with 15.2(1)SY, 6800-IA running with 15.2(3)E.
Cisco TAC is investigating that issue, but till now without any result.
When the issue occurs, the recorded logging messages are:
Syslog 6880-X
Apr 7 07:42:43.182: %PLATFORM_RPC-3-MSG_THROTTLED: RPC Msg Dropped by throttle mechanism: type 3, class 21, max_msg 32, total throttled 1274 (FEX-101)
Apr 7 07:45:43.181: %PLATFORM_RPC-3-MSG_THROTTLED: RPC Msg Dropped by throttle mechanism: type 3, class 21, max_msg 32, total throttled 1276 (FEX-101)
Syslog 6800-IA:
Apr 7 07:57:43.182: %PLATFORM_RPC-3-MSG_THROTTLED: RPC Msg Dropped by throttle mechanism: type 3, class 21, max_msg 32, total throttled 1284
-Traceback= 5198C4z 21413F8z 1C3B35Cz 1C3C6FCz 1C3CA00z 2654CC0z 26509BCz
Apr 7 08:00:43.181: %PLATFORM_RPC-3-MSG_THROTTLED: RPC Msg Dropped by throttle mechanism: type 3, class 21, max_msg 32, total throttled 1286
-Traceback= 5198C4z 21413F8z 1C3B35Cz 1C3C6FCz 1C3CA00z 2654CC0z 26509BCz -
When setting up my apple I'd I get a verification email but there does not seen to be a link to click on there is a link that says "verify now" but it's not a link the only other thing on the page is a link to apple thats starts the process all over again.does anyone have a solution for this problem?
The idea to jumpstart by change was not the smartest one, but gives you an opportunity to use that "temporary" account as permanent. You do not have a choice cause obviously despite you thinking that old account is no more -it does exist on Apple servers. And if you are unwilling to share your [email protected] with friend, just create one extra [email protected] for your friend. One suggestion - do not use gmail.
-
Report columns not exported to excel if the column values are links(URLs)
Hi Friends,
I am facing this weird situation in my development environment at work using Apex 3.1.2.00.02.
There is this report where I am using this huge query below to show the statistics of various file loads.
SELECT f.load_date "Load Date",
c.cust_name "Customer",
a.file_id "File ID",
f.rec_count "Total Records Processed",
a.success "Successful Records",
a.file_translation_errors "Customer Validation Errors",
a.data_referential_errors "CS Validation Errors",
a.no_activity_type_assigned "No Activity Type Assigned"
FROM (SELECT file_id,
NVL (MAX (success), 0) success,
NVL (MAX (file_translation_errors), 0) file_translation_errors,
NVL (MAX (data_referential_errors), 0) data_referential_errors,
NVL (MAX (no_activity_type_assigned), 0) no_activity_type_assigned
FROM ((SELECT file_id,
COUNT (*) success,
NULL file_translation_errors,
NULL data_referential_errors,
NULL no_activity_type_assigned
FROM ah_activity_external
WHERE status_id IN (43, 53)
GROUP BY file_id)
UNION
(SELECT file_id,
NULL success,
COUNT (*) file_translation_errors,
NULL data_referential_errors,
NULL no_activity_type_assigned
FROM ah_cust_gis_arch
WHERE status_id IN (1, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 22, 23)
GROUP BY file_id)
UNION
(SELECT file_id,
NULL success,
NULL file_translation_errors,
COUNT (*) data_referential_errors,
NULL no_activity_type_assigned
FROM ah_cust_gis_arch
WHERE status_id IN (24, 15, 16, 17, 18)
GROUP BY file_id)
UNION
(SELECT file_id,
NULL success,
NULL file_translation_errors,
NULL data_referential_errors,
COUNT (*) no_activity_type_assigned
FROM ah_activity_internal
WHERE status_id IN (26, 31)
GROUP BY file_id))
WHERE file_id IN (
SELECT file_id
FROM ah_chain_file
WHERE chain_id = :p2_customer
AND load_date BETWEEN :p2_load_start_date AND :p2_load_end_date)
GROUP BY file_id) a JOIN ah_chain_file f ON ( a.file_id = f.file_id
AND f.file_default = 'N')
JOIN ah_chain c ON (f.chain_id = c.chain_id)In the above query I have made the following columns as links which would redirect to other pages showing the respective records.
1) "Successful Records"
2) "Customer Validation Errors"
3) "CS Validation Errors"
4) "No Activity Type Assigned"
Also I have enabled CSV output under "Report Export"
Now the issue is when I downloaded this entire report into spreadsheet, only the non-url columns are being exported.
I have even made sure that "Include In Export" under Column Attributes is set to YES.
I tried to reproduce this issue using Dept & Emp tables but it seems to be working there.
I don't know if it is the query which is causing this issue or a genuine Apex bug.
Hope someone might have faced some thing like this earlier.
Appreciate your thoughts on this.
Thanks,
Raj.Raj,
see if this helps you:
http://apex.oracle.com/pls/otn/f?p=31517:22
Denes Kubicek
http://deneskubicek.blogspot.com/
http://www.opal-consulting.de/training
http://apex.oracle.com/pls/otn/f?p=31517:1
------------------------------------------------------------------- -
Revision: 10913
Author: [email protected]
Date: 2009-10-07 12:04:30 -0700 (Wed, 07 Oct 2009)
Log Message:
Reverted my previous reversion, since the original change wasn't the cause of the Mustella breakage. So once again:
The 'lineBreak' style is now properly declared as non-inheriting.
For a long time we've intended for it to be non-inheriting... it lives in BasicNonInheritingStyles.as! And we want it to be non-inheriting, because in TLF this format does not inherit from parent FlowElement to child FlowElement, so in Flex is should not inherit from parent UIComponent to child UIComponent. But the metadata incorrectly said inherit="yes". It now correctly says inherit="no".
QE notes: None
Doc notes: None
Bugs: SDK-23569
Reviewer: Ryan
Tests run: ant checkintests
Is noteworthy for integration: Yes
Ticket Links:
http://bugs.adobe.com/jira/browse/SDK-23569
Modified Paths:
flex/sdk/trunk/frameworks/projects/spark/src/spark/styles/metadata/BasicNonInheritingText Styles.asDue to a copy/paste glitch, some necessary spaces have inadvertently been removed. If I could fix this, I would.
-
Hi,
I'm running web applications and there is performance issue is most probably caused by the fact that IE can not handle such amount of requests that are forwarded to the server at the same time.
Data:
On IE(10) – search variety 11- it takes a long time (about 25 seconds for response) .
in general, the responding time of "search variety" in IE is much longer than Chrome.
IE - see:http://screencast.com/t/kSeT3hC2mRfV
Chrome see:http://screencast.com/t/NYf6fskU
Why? any solution ?
Thanks,Hi,
without a link to your site (so we can use the same tools mentioned above)... we can only guess.
these are peer to peer support forums... your favorite web search engine will help you to learn about web development.
display the Developer tool console in each browser to view the suppressed error messages.
All modern browsers support the performance api or your can use the Networking tab to view the latency metrics for the site.... commonly you may be using meta directives for caching instead of server headers or you have different settings between browsers
which determine how long resources are cached. Commonly, IE has a different security model to other browsers... ensure that you are using the Default IE security zone settings.... Actions like innerHTML go through a sanitization process to remove script content...
Commonly AJAX calls are made during the onload event...
Please post questions about web site development to the IE Web Developer forum. Include with your questions a link to your website or a publicly accessible mashup that shows your issue.
Questions regarding Internet Explorer 8, 9 and 10 and Internet Explorer 11 for the IT Pro Audience. Topics covered are: Installation, Deployment, Configuration, Security, Group Policy, Management questions. If you are a consumer looking for answers or to
raise a question, it's highly recommended you head on over to http://answers.microsoft.com
Rob^_^ -
Hello, I've got a Upgrade-Version of CS5.5 for Windows and changed to a Mac. Now I need the Mac-Version. I tried to install the Download from Adobe. Unfortunatly it didn't accept my password. I guess cause of the Upgrade-Version or the Windows Version I own. My System: Mac OS X 10.6.8, 2,8 GHz. Thanks for answers! Greetings, Eva
Here is a link to the info regarding platform swaps.
Order product | Platform, language swap
If you want to try to contact Adobe support to try to get an exception, Start Here after selecting relevant responses choose "Still need help? Contact us." and the chat contact (or phone) option. -
What happened to the Giant DSR-11 Timecode out thread
What happened to the Giant DSR-11 Timecode out thread? The one about using simple video out to stripe the tape.
people keep asking me how to do it, and I'd love to just send them a link to that thread, but can't find it when I search for it. Anyone have the link?
thanks, timNaa, props like the kind that hold me up when I've had too much to drink.
Or maybe the props that make the plane go.
Or maybe I should have said "mad props."
http://www.randomhouse.com/wotd/index.pperl?date=20010213 -
Questions about tuning the USRP packet -based link examples
Hi everyone,
Today I do some tests and tunning on the USRP packet-based link examples, and I find these questions:
First I set the following parameters to the Packet Transmitter.vi: Tx frequency=2441M, samples per symblol=8, sample rate=800k, then the symbol rate should be 100k
Then I set the Rx frequency to 2441=M and do three tests to the USRP packet receiver.vi:
1. set the samples per symbol to 8, the sample rate to 800k, all the packets can be received correctly very fast.
2. set the samples per symbol to 40, the sample rate to 4M, all the packtes can be received correctly, but slower than the former test.
3. set the samples per symbol to 50, the sample rate to 5M, all the packets can be received correctly, but much slower than the former two tests.
4. set the samples per symbol to 40, the sample rate to 5M, but change the sample rate to 4M when input the argument to the resample&demod_shell.vi, then I find that no packets can be received correctly.(According to my understanding, resampling the data with 4M sample rate should make the input data time-aligned)
Can anyone help me interprete above test? Thanks in advance!Hi 0711,
You are correct. If you sample at 5MS/s and have a samples/sym of 40, resampling with a sample rate of 4MS/s will allow you to receive the signal. Digging into the sub_resample_and_demodulate.vi, I found the issue. The modulation toolkit resample VI that is being used pulls the sample rate of the incoming signal from the incoming waveform (or the dt of the incoming waveform). In the resample and demodulate subvi, the dt of the incoming signal was hard wired to be 1/x of the desired sampling rate. For all other uses cases, having these 2 parameters hard wired together does not cause a problem, but for the 4th case you described it does. I edited the subvi like shown in the image below and was able to get it working:
Hope that helps and let me know if you have any further questions. I'll do my best to get you an answer.
Sarah Y
SDR Product Manager
National Instruments | Ettus Research -
Revision: 4859
Author: [email protected]
Date: 2009-02-05 10:15:22 -0800 (Thu, 05 Feb 2009)
Log Message:
-Fix packaging timing issue that was caused by the rebuilding of the air applicationupdater. The recompiled files would get laid down properly only to have the old files put back down on top of them. I also made sure the build directory was removed after updateAIR ran so it would not be included in the package
-removed bundles.properties from the wireframe project
bug:SDK-19128
qa:yes
doc:no
checkintests:pass
Ticket Links:
http://bugs.adobe.com/jira/browse/SDK-19128
Modified Paths:
flex/sdk/branches/i10/build.xml
flex/sdk/branches/i10/frameworks/build.xml
Removed Paths:
flex/sdk/branches/i10/frameworks/projects/wireframe/bundles.propertiesHi Chris,
I have confirmed this is an AIR SDK 13.0.0.83 bug.
I have reported this bug to Adobe Bugbase, and I also included the workaround:
https://bugbase.adobe.com/index.cfm?event=bug&id=3750892
The workaround is:
Simply comment the <externalSwfs> tag in your -app.xml will solve this bug, like this: <!-- <externalSwfs></externalSwfs> -->
DarkStone
2014-04-28 -
Some worksheets missing the format and stoplight link in viewer
I have a set of workbooks that are pretty simple. Each has from 1 to 4 worksheets. I have one workbook where two of the worksheets when run through viewer do not show a format or stoplight link, but the other two do show the links. Is there something that blocks these links from being displayed?
This issue occurred in our system too.
We are running Oracle BI 10.1.2 on a Windows 2003 Server machine. The "format" and "stoplight" link suddenly disappeared from Disco Viewer.
Does anybody know what can have caused this?
ps: moreover the font of the Viewer page is smaller since this happened -
Cisco Pix 515 failover how to know the cause of the fail
Hello All,
We have 2 units 515 in failover configuration.
From the last Thursday we are having problems in our pixs.
The primary unit fail and then the standby works.
We need to know what is the real cause of the problem.
We have configured logging and when we check the syslog messages we can´t find anything important.
Our version is 6.3(5).
Can anybody help us?
If you need more information, please tell me.
Thanks in advance.
Martin.Hello Gurpreet,
Our failover system is working only with the failover cable, not with netwaork cable.
High CPU is occuring in primary unit. The high cpu usage was after the issue.
One thing, disconnecting for a seconds the cable for interfece "inside" (this cable connects th firewall to our network) the failover runs again ok. We can´t understand it.
Here is the sh interface
Thanks again.
Martin
FWPERIMETRO(config)# sh interface
interface ethernet0 "inside" is up, line protocol is up
Hardware is i82559 ethernet, address is 000b.bef7.56c5
IP address 172.17.4.122, subnet mask 255.255.252.0
MTU 1500 bytes, BW 100000 Kbit full duplex
165844 packets input, 2811391461 bytes, 0 no buffer
Received 947714 broadcasts, 0 runts, 0 giants
1294 input errors, 0 CRC, 0 frame, 1294 overrun, 0 ignored, 0 abort
165698 packets output, 4122450665 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
input queue (curr/max blocks): hardware (128/128) software (128/128)
output queue (curr/max blocks): hardware (128/128) software (971/1189)
interface ethernet1 "internet" is up, line protocol is up
Hardware is i82559 ethernet, address is 000b.bef7.56c6
IP address 195.55.225.98, subnet mask 255.255.255.240
MTU 1500 bytes, BW 100000 Kbit full duplex
20253 packets input, 6232273 bytes, 0 no buffer
Received 1830 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
22281 packets output, 2876208926 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
<--- More --->
input queue (curr/max blocks): hardware (128/128) software (8/128)
output queue (curr/max blocks): hardware (2/115) software (0/1)
interface ethernet2 "failover" is up, line protocol is down
Hardware is i82558 ethernet, address is 00e0.b606.92d7
IP address 192.168.254.253, subnet mask 255.255.255.252
MTU 1500 bytes, BW 10000 Kbit half duplex
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
31 packets output, 320148 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
31 lost carrier, 0 no carrier
input queue (curr/max blocks): hardware (128/128) software (0/0)
output queue (curr/max blocks): hardware (0/10) software (0/1)
interface ethernet3 "dmz-2" is up, line protocol is up
Hardware is i82558 ethernet, address is 00e0.b606.92d6
IP address 195.76.142.185, subnet mask 255.255.255.248
MTU 1500 bytes, BW 100000 Kbit full duplex
1179 packets input, 2703322420 bytes, 0 no buffer
Received 2074 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
720 packets output, 4209917559 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
<--- More --->
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
input queue (curr/max blocks): hardware (128/128) software (1/101)
output queue (curr/max blocks): hardware (0/42) software (0/1)
interface ethernet4 "wandas" is up, line protocol is up
Hardware is i82558 ethernet, address is 00e0.b606.92d5
IP address 10.132.0.18, subnet mask 255.255.255.0
MTU 1500 bytes, BW 100000 Kbit full duplex
164402 packets input, 1499053954 bytes, 0 no buffer
Received 411 broadcasts, 0 runts, 0 giants
267 input errors, 0 CRC, 0 frame, 267 overrun, 0 ignored, 0 abort
159201 packets output, 1116228713 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
input queue (curr/max blocks): hardware (128/128) software (128/128)
output queue (curr/max blocks): hardware (0/128) software (0/49)
interface ethernet5 "dmz" is up, line protocol is up
Hardware is i82558 ethernet, address is 00e0.b606.92d4
IP address 172.23.4.2, subnet mask 255.255.255.0
MTU 1500 bytes, BW 100000 Kbit full duplex
16067 packets input, 942162666 bytes, 0 no buffer
Received 2108 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
<--- More --->
13916 packets output, 494350387 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
input queue (curr/max blocks): hardware (128/128) software (6/79)
output queue (curr/max blocks): hardware (0/65) software (0/1) -
i'm trying to read several interactive pdf on my ipad, but when i touch the screen it ppeares a top bar with "ok" that if i touch it closes the pdf, an upload button, & the thumbnails of the pages on the righ side of the screen appears too. Does anybody know how to avoid it? Thank's
Are you saying that all pages appear blank when you open the particular PDF document (AINF....pdf) in Adobe Reader for iOS? It may be due to a bug in Adobe Reader for iOS.
You mentioned "links"...There are three different actions that the desktop version of Adobe Reader supports for links.
Go to a page view (within the same document)
Open a web page
Open a file
Adobe Reader mobile products (for iOS, Android, Windows Phone) support the first two but does not support opening a PDF file or any other types of files.
Additionally, hyperlinks are not visible in Adobe Reader mobile products. (It used to show hyperlinks in light blue highlight. But due to customer complaints, hyperlink highlighting has been disabled.)
Please let us know if you can share your PDF document with us (Adobe). We can take a look at it and diagnose the cause of the problem. Thank you. -
How to monitor the quality of WAN link?
Dear All,
I have a basic problem; my remote site has unstable link so the VoIP system can't work well.
Do you have any way to monitor the quality of WAN link:
How to track the paths that packets travel from source to destination? (each packet has different path to reach the same destination)
How to track the sequence of packet? (tcp/udp packets reach the destination with the wrong sequence)
Thanks You very much for helping me!Disclaimer
The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
Liability Disclaimer
In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
Posting
As the other posters have noted, IP SLA is an excellent feature for doing all kinds of quality monitoring. However, besides finding a tool that can "nicely" report on SLA stats, you'll probably want one that can also define the SLA tests too. (Unfortunately, I don't have a recommendation for such a tool.)
BTW, if different packets are taking different paths and/or often arriving out of sequence, you probably have some device with multiple egress paths doing packet-by-packet load balancing, which can cause all kinds of performance issues. You might also be able to find that device by using a simple traceroute. Look for hops with multiple paths. -
Cisco 6500 VSS , VSL Link Connection Issue
Hello Everyone
actually i have two Cisco 6509E with two VS-S720-10G and want to run VSS on them
i do all the config same as cisco recommend, but i get somethings wrong on them, 1st. on switch2 , under "switch virtual domain" when i enter switch2, its not accepot and 2nd. non of 10G link goes up & so VSL link always down
here is my config and show commands
SWITCH#1
==================================
switch virtual domain 10
switch mode virtual
switch 1 priority 110
mac-address use-virtual
redundancy
main-cpu
auto-sync running-config
mode sso
interface Port-channel1
no switchport
no ip address
switch virtual link 1
mls qos trust cos
no mls qos channel-consistency
interface TenGigabitEthernet1/5/4
no switchport
no ip address
mls qos trust cos
no cdp enable
channel-group 1 mode on
interface TenGigabitEthernet1/5/5
no switchport
no ip address
mls qos trust cos
no cdp enable
channel-group 1 mode on
======
SWITCH#2
switch virtual domain 10
switch mode virtual
switch 1 priority 110
redundancy
main-cpu
auto-sync running-config
mode sso
interface Port-channel2
no switchport
no ip address
switch virtual link 2
mls qos trust cos
no mls qos channel-consistency
interface TenGigabitEthernet2/5/4
no switchport
no ip address
mls qos trust cos
no cdp enable
channel-group 2 mode on
interface TenGigabitEthernet2/5/5
no switchport
no ip address
mls qos trust cos
no cdp enable
channel-group 2 mode on
Thank you all in advanceHello Dear Reza
at first, thanks for your replay
below you can find the Show Version of the SWITCH#1
6500-1#sh version
Cisco IOS Software, s72033_rp Software (s72033_rp-ADVENTERPRISEK9-M), Version 15.1(1)SY1, RELEASE SOFTWARE (fc5)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Wed 01-May-13 13:16 by prod_rel_team
ROM: System Bootstrap, Version 12.2(17r)SX5, RELEASE SOFTWARE (fc1)
BOOTLDR: Cisco IOS Software, s72033_rp Software (s72033_rp-ADVENTERPRISEK9-M), Version 15.1(1)SY1, RELEASE SOFTWARE (fc5)
6500-1 uptime is 6 minutes
Uptime for this control processor is 6 minutes
System returned to ROM by power cycle at 11:49:28 UTC Mon Nov 17 2014 (SP by power on)
System image file is "sup-bootdisk:s72033-adventerprisek9-mz.151-1.SY1.bin"
Last reload reason: reload
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco WS-C6509-E (R7000) processor (revision 1.6) with 983008K/65536K bytes of memory.
Processor board ID SMC18080014
SR71000 CPU at 600Mhz, Implementation 0x504, Rev 1.2, 512KB L2 Cache
Last reset from s/w reset
1 Virtual Ethernet interface
99 Gigabit Ethernet interfaces
5 Ten Gigabit Ethernet interfaces
1917K bytes of non-volatile configuration memory.
65536K bytes of Flash internal SIMM (Sector size 512K).
Configuration register is 0x2102
as you see i use "adventerprisek9-mz.151-1.SY1" but now downgrade it to "s72033-adventerprisek9_wan-mz.122-33.SXJ2" , so nothing change and EtherChannel still not up
below are the show commands:
VSS-Sw2#show etherchannel 2 summary
Flags: D - down P - bundled in port-channel
I - stand-alone s - suspended
H - Hot-standby (LACP only)
R - Layer3 S - Layer2
U - in use N - not in use, no aggregation
f - failed to allocate aggregator
M - not in use, no aggregation due to minimum links not met
m - not in use, port not aggregated due to minimum links not met
u - unsuitable for bundling
d - default port
w - waiting to be aggregated
Number of channel-groups in use: 1
Number of aggregators: 1
Group Port-channel Protocol Ports
------+-------------+-----------+-----------------------------------------------
2 Po2(RD) - Te2/5/4(D) Te2/5/5(D)
Last applied Hash Distribution Algorithm: -
===========================
VSS-Sw2#sh etherchannel 2 port
Ports in the group:
Port: Te2/5/4
Port state = Down Not-in-Bndl
Channel group = 2 Mode = On Gcchange = -
Port-channel = null GC = - Pseudo port-channel = Po2
Port index = 0 Load = 0x00 Protocol = -
Age of the port in the current state: 0d:00h:00m:00s
Port: Te2/5/5
Port state = Down Not-in-Bndl
Channel group = 2 Mode = On Gcchange = -
Port-channel = null GC = - Pseudo port-channel = Po2
Port index = 0 Load = 0x00 Protocol = -
Age of the port in the current state: 0d:00h:00m:00s
Last applied Hash Distribution Algorithm: -
Maybe you are looking for
-
Hello: When I open a PDF and try to use the Ctrl F (Find feature), the colorful spin wheel pops up and it spins for a while. When it finishes I get an error box that’s titled ‘Adobe Reader Quit Unexpectantly’. The following is all of the in
-
Can i choose which songs are added to the itunes match library?
can i choose which songs are added to the itunes match library?
-
Replacement Nano under warranty also defective. Will not pay shipping 2x!!
I had a Nano 2nd Gen purchased last December. It had an audio jack problem and needed to be replaced. I do not have Apple Care, btw. I had to pay shipping to get the Nano replaced; about $30, a shipping fee that is a bit ridiculous in and of itself.
-
Urgent help:- Generate report from AD
Team, Can any one help me to generate report from AD in below format. User ID, MSOID, active/inactive, First Name, Last Name, Last login date. thanks in advance Regards, Triyambak Regards, Triyambak
-
As secondary display was implemented on lightroom 2, it seems to me impossible tweaking the images with the wacom cintiq. Have I lost something about, specially the tablet?