How can a BILBO can be used as a pseudo-random pattern generator.(using labview)

how can a BILBO can be used as a pseudo-random pattern generator.(using labview) Can someone please give me an insight on how to do this asap, i would be exteremely grateful-thanks.

Dear Deano,
I am unfamiliar with the use of BILBO cells, but am willing to help as much as I possibly can. I managed to find a rather helpful website, which described the 4 functions a BILBO register is capable of – including pseudo-random pattern generation. A very versatile little circuit, I must say.
Perhaps you could take a look at the website yourself, and confirm that this is the functionality you are interested in...
http://tams-www.informatik.uni-hamburg.de/applets/hades/webdemos/35-selftest/60-bilbo/bilbo4.html
Could I also ask you to provide some more information about what you are trying to achieve. Generally, the more information you are able to provide on these forums, the more users will be willing to help.
So my question to you is... are you trying to mimic a BILBO's functionality (using LabView) or talk to a piece of BILBO hardware (using Labview)? If the later is the case, could you let us know how you trying to communicate with the device.
However, if the former is the case, and you are purely interested in random sequence generation, perhaps you should consider some of the LabView functions. They may be able to provide a more efficient means of producing random patterns. Obviously, the “random number function” springs to mind. You could easily use this in conjunction with a “less than” function to produce a random digital bit.
Please also provide the version of LabView and Measurement & Automation Explorer you are using.
Thanks you for your time,
Best wishes and kind regards,
Message Edited by RER on 04-07-2008 06:06 AM
Rich R
Applications Engineer
National Instruments UK & Ireland

Similar Messages

How can I use LabVIEW to send the equivalent of a CTRL D (in VT 100 format) out the serial port of my computer?

I am trying to write a vi that interfaces with a piece of OEM equipment that is set up to talk with a VT 100 terminal. I can't seem to locate the ASCII equivalent string (if there is such a thing) of a CTRL D. Is there a vi that emulates VT 100 commands?

If I recall, CTRL-D is EOF on most ASCII tables.
You'd probably have to use an escape sequence
or if you can use an unsigned 8-bit that might be
easier.
In article <[email protected]>, TLS
wrote:
> How can I use LabVIEW to send the equivalent of a CTRL D (in VT 100
> format) out the serial port of my computer?
>
> I am trying to write a vi that interfaces with a piece of OEM
> equipment that is set up to talk with a VT 100 terminal. I can't seem
> to locate the ASCII equivalent string (if there is such a thing) of a
> CTRL D. Is there a vi that emulates VT 100 commands?

How can i use labview for communicating with pic18 microcontroller through usb port?

Hi all,
I want to make a DAQ card using pic 18 microcontroller which has a built-in usb protocol. I have the firmware of this
controller which will make it as a usb device. How can i receive the analog voltages from this DAQ card in Labview? or i mean to say that how i can communicate labview with the Pic 18 microcontroller through usb port? I have also the
mpusbapi.dll file which is for Visual C++. Can i make changes in this dll file to make it compatible with labview?

Which labview version do you have. Up to labview 7.1 it was no USB raw communication options. I have heard it did not work well in 7.1, but from 8.x most of the errors were fixed.
Here is a link it should be useful http://forums.ni.com/ni/board/message?board.id=170&message.id=340676&query.id=365864#M340676
Besides which, my opinion is that Express VIs Carthage must be destroyed deleted
(Sorry no Labview "brag list" so far)

How can i use labview.tlb to control Labview from an external application?

Hi,
I've been told by a labview engineer that i could use the file
labview.tlb located in the labview install folder to control labview
from an external application (in my case, a C# app). I'm using Labview
6.1 under Windows 2000. This article confirms that:
"ActiveX and LabVIEW"
http://zone.ni.com/devzone/conceptd.nsf/webmain/5401BE584FBAEECE862567C2006D36C7?opendocument
But i've not been able to find out how to use this file to achieve
what i want. I just want to be able to open/close labview, open/close
a vi, start/stop a vi, hide/show a vi from a C# application. The above
web page talks about activex but i really don't see the realtion
between activex and that labview.tlb file.
Is there so
mebody around who knows how to use that file? Why does NI
tell us that it's possible to do what i want to do but doesn't explain
how (or hides this info very well)?
Thanks

Hi,
> Hi I am fighting a similar problem and so far I found this: Calling
> LabVIEW from C++ Using ActiveX
>
> http://sine.ni.com/apps/we/niepd_web_display.DISPLAY_EPD4?>p_guid=B45EACE3E21356A4E034080020E74861&p_node=DZ52051&p_submitted=N&p_rank=&p>_answer=&p_source=External
Thanks for the link, i actually already found this link before. I've
found yesterday how to use Labview.tlb, just add it to the references
of the project, it was probably too easy for me at that time:-) But
now, i'm still stuck as there is no doc about using the interfaces and
classes of this activex to control labview.
The example given on your link is made is C++ and for some reasons,
the wrapper generated for Labview.tlb when i added it to my c# project
doesn't seem to expose the same
interfaces and classes as the one used
in the C++ example. I therefore can't use the C++ example in C#.
I've tried to do something like:
LabVIEW.ApplicationClass a = new LabVIEW.ApplicationClass();
Just this line causes labview to launch but then immediately throws an
exception: "Query interface for interface LabVIEW._IApplication
failed".
Does somebody knows how to use that control in C#/VB.NET ?

How can I use LabView to control Altera Scripting

Hi
I have kind of run into a stone wall. I am building a production test executive based on LabView. Part of this process includes loading an FPGA image on to a CFI flash that is in the JTAG chain. I am trying to make so that the production operators don't have to open a second application, select the right FPGA and Flash navigate to the file then load it, then go back to LabView and run the rest of the tests.
Altera has a command line interface that will let me load .cdf file. The problem is that nowhere in Altera’s documentation does it show me how to first load the “Parallel Flash Loader IP” into the FPGA. The flash loader acts as a temporary bridge between the JTAG input and the CFI Flash. I have looked on Altera’s Forums and have had an open ticket with Altera’s support engineers for more than a week.
I can’t be the first person to want to do this; I am hoping someone here has done it before. I would really rather not try to use the activeX controls to manipulate the windows based program.
Any suggestions would be greatly appreciated (Note I am not trying to put LV code on the FPGA/Flash just use LV to control the process)
Thanks in advance
Below is the error message and the script I am using. It almost works just missing the flash loader IP
C:\altera\12.1sp1\qprogrammer\bin>quartus_pgm -c USB-BLASTER -m JTAG S_FPGA.
cdf
Info: *******************************************************************
Info: Running Quartus II 32-bit Programmer
    Info: Version 12.1 Build 243 01/31/2013 Service Pack 1 SJ Full Version
    Info: Copyright (C) 1991-2012 Altera Corporation. All rights reserved.
    Info: Your use of Altera Corporation's design tools, logic functions
    Info: and other software and tools, and its AMPP partner logic
    Info: functions, and any output files from any of the foregoing
    Info: (including device programming or simulation files), and any
    Info: associated documentation or information are expressly subject
    Info: to the terms and conditions of the Altera Program License
    Info: Subscription Agreement, Altera MegaCore Function License
    Info: Agreement, or other applicable license agreement, including,
    Info: without limitation, that your use is for the sole purpose of
    Info: programming logic devices manufactured by Altera and sold by
    Info: Altera or its authorized distributors. Please refer to the
    Info: applicable agreement for further details.
    Info: Processing started: Thu Oct 03 18:16:53 2013
Info: Command: quartus_pgm -c USB-BLASTER -m JTAG S_FPGA.cdf
Info (213045): Using programming cable "USB-Blaster [USB-0]"
Info (209060): Started Programmer operation at Thu Oct 03 18:17:19 2013
Error (209062): Flash Loader IP not loaded on device 1
Error (209053): Unexpected error in JTAG server -- error code 5
Error (209012): Operation failed
Info (209061): Ended Programmer operation at Thu Oct 03 18:17:21 2013
Error: Quartus II 32-bit Programmer was unsuccessful. 3 errors, 0 warnings
    Error: Peak virtual memory: 376 megabytes
    Error: Processing ended: Thu Oct 03 18:17:21 2013
    Error: Elapsed time: 00:00:28
    Error: Total CPU time (on all processors): 00:00:03
Solved!
Go to Solution.

Hi Eric,
I got it figured out today, basically you have to load the Parallel Flash Loader first into FPGA ram. It is a special .sof file (pfl_epXXXX.sof) based on your FPGA. Code is actually pretty straight forward, using the Sys Exec VI. Use the windows based programmer to generate the .cdf file that identifies your FPGA, attached Flash and .pof file .
Syntax was odd going into Sys Exec. Note the extra "C" in in front of the "quartus_prm.exe" I have no idea why that was needed, but I was getting an error until I just happened to put it in there (Blind Luck :-))
I used a 2 element array going into a four loop
cmd /cquartus_pgm.exe -c USB-BLASTER -m JTAG -o P;pfl_epXXXX.sof
cmd /cquartus_pgm.exe -c USB-BLASTER -m JTAG S_FPGA.cdf
Defining the working director C:\altera\12.1sp1\qprogrammer\bin
And added match string with "Successfully performed operation" on the output in the loop to make sure everything loaded correctly then adding the array to give me a overall P/F
To anyone doing this same thing Altera's documentation is poor to say the least. It took most of a week to figure this out Not allowed to upload code, so anyone wanting details just post here and I will try to help. This was painful, with lots of lessons learned.
Thanks for the interest though
Best regards John

How can I use LabVIEW to ground floating SCXI-1520 channels (in order not to lose scanning capabilities from the multiplexer)?

Currently I am reading quarter bridge strain with several SCXI-1520s. When in MAX I noticed my values were no longer reading after a certain gage and as I attempted to troubleshoot, found out that the multiplexer in this module will not scan past any open channel (or if it does, channel results are not consistent) for a very logical reason. If I lose a gage, I usually lose any data from any subsequent gages which we really cannot afford.
Are there any suggestions programming in LabVIEW (right now i'm using NI-DAQmx with an analog task set up)so that each time my loop executes, the program will check for any open channels and either not collect that data or change the order of acquisition (i.e. place the open channels last on the scan list?
I'm open to anything that might be of help

Yes, by "open channel" i mean that there is no signal returning from the gage because it has broken off the structure or the signal to the terminal block has been disconnected somehow.
When I lose data, I'm referring to the data that is acquired on following channels. The behavior appears to be fairly random (which was a troubleshooting nightmare ) but usually if a channel is open, then that and those behind it in the scan order do not return any data. It returns a number like 10.357E-6 and I do not pick up any noise or fluctuations. As far as I understand, the multiplexer stops scanning at this point (open channel) because it has nothing to ground to and subsequently "hangs" - not (or randomly) scanning the following channels. I have gone through the bridge configuration and as of yet, have not figured out how to fix this using any hard-wiring techniques. I emailed NI, and was sent a library file to "ground the channels" but it actually resets the Analog input Task I have defined each loop.
I am new to NI-DAQmx so I do not know if this will alter any configurations I already have in MAX for NI-DAQmx. Will it override? I am concerned it will slow my loop time, and also I cannot see the code for this sub.vi so am a little skiddish about using it if i do not know if it can be tailored to my app.
What do you think? Am I on the right path?

How can I use LabVIEW 6 on a SCXI-FRQ8 module?

Hi, here is a description of our problem. We hope that you will be able to help us.
We bought from NI, a few years ago, some SCXI-FRQ8 modules. (Those modules were made by a company called Developpement Ingenierie in France) The problem is, we can not update to the version 6 of labview since we do not have the drivers to install Labview 6. The drivers we have are for Labview 5.x and 4.x.
Furthermore, we can not update those drivers by ourselves, since we do not have acces to the diagram of these VI drivers. We tried to contact that company, but no one answers. So maybe the company does not even exists anymore.
We would like to be able to install Labview 6 on these modules and if we can
make it work, we will probably buy some new SCXI-FRQ8 modules(if we can still buy them).
Thank you

The driver for the SCXI-FRQ8 provided by DI originally did not include the block diagrams. So if you try to use them in a newer version of LabVIEW, you will receive error messages because LabVIEW needs the source code to recompile the code into the newer LabVIEW format.
National Instruments can provide you with the code you need to use this module with LabVIEW 6. Request this code at http://www.ni.com/ask.
Raecine Meza
Applications Engineer
National Instruments

How can i use labview for notebook

i want to know spec of notebook for install labview programm.
thank you vermuch.
sattaya

Sattaya,
here you can find the system requirements for installing the LabVIEW development environment.
Please post merely LabVIEW related questions to the LabVIEW board. The LabVIEW community is much bigger than the motion control community, so you will get answers quicker there.
Regards,
Jochen Klier
National Instruments

How can I use Labview to create a graph of digital voltage signal vs. Time?

I am measuring a digital voltage signal and I need to generate a graph vs. Time and be able to add user controls to start/stop the graphing and be able to export the graph to other programs such as MS Excel. Any help you could give would be much appreciated. Thank you.

You probably want to use a chart. Place it inside a while loop that runs continuously. The chart should be in a case structure so it is bypassed depending on the boolean pause/continue switch.
To save the data, get the "history data" of the chart via a propery node and save it to a file. It is probably easiest to save it to an ASCII file. Most other programs will be able to read it.
See how far you get. If you get stuck, post your VI and we'll help you.
LabVIEW Champion . Do more with less code and in less time .

How can i use labview to acquire temperature from optical fibre sensors

i am trying to develop an application that would enable a user to acquire temperature data from optical fibre sensors and display the profile on a PC screen but i have got no clue of how to go about it

To provide some assistance, I will need to know:
1) What type of output does the device produce? (volts, current, frequency ...)
2) What type of conditioning does the signal require? (gain, filter, excitation, bias resistors ...)
3) What type of calibration does the vendor provide? (how the output signal relates to temperature)
These characteristics have already been determined by the manufacturer (or the engineer who developed the interface electronics).
You have made no mention of the computer, OS, software, or hardware you will use. I could try to walk you through the selection process; however, I would probably take up too much space trying to discuss all of the possible combinations.
Could you provide some additional information about hardware and soft
ware you will use? I will look for a response.

How can I use Labview to recall saved states on my HP8920B RF Test Set

I need labview6.1 to recall saved states on my RF Tester. There is a recall button on the front of my tester, all you have to do is select the state's name and it opens up on the screen. I want Labview to do this work with a click of the mouse. I am using the HPIB (GPIB) interface, which seems to be working with the HP8920 driver (I couldn't find one for the 8920b). If anyone could help me out, that would be great.

Try *RCL [State name]. Send this command to the 8920B. Sample code included.
Attachments:
8920_State_Recall.vi ‏11 KB

How can I use LabVIEW as an OPC-client, without using datasockets ?

I heared that would be possible with the newest edition.

The Datalogging and Supervisory Control (DSC) add-on module makes LabVIEW an OPC Client (and a Server).

How can I use 2 Apple IDs in Itunes? I have 2 IOS Devices. They each have there own AppleID. What is the proper way to sync both of them to Itunes?

How can I use 2 Apple IDs in Itunes? I have 2 IOS Devices. They each have there own AppleID. What is the proper way to sync both of them to Itunes? I wanted my teenager's AppleID to be different from mine so that she couldn't charge stuff to my AppleID, therefore I created me another one. Now when I go to Sync either device, it tells me that this IOS device can only be synced with one AppleID. Then I get a message to erase it, not going to do that, lol. If I logout as one ID and login as the other, will it still retain all synced information on the PC from the first IOS device? If I can just log in out of the AppleID, then I have no problem doing that as long as the synced apps, music, etc stays there for both. I am not trying to copy from one to the other, just want to make sure I have a backup for the UhOh times. If logging in and out on the same PC of multiple AppleIDs is acceptible then I need to be able to authorize the PC for both devices. Thanks for the help. I am new to the iOS world.

"Method Three
Create a separate iTunes library for each device. Note:It is important that you make a new iTunes Library file. Do not justmake a copy of your existing iTunes Library file. If iTunes is open,quit it.
This one may work. I searched and searched on the website for something like this, I guess I just didn't search correctly, lol. I will give this a try later. My daughter is not be back for a few weekends, therefore I will have to try the Method 3 when she comes back for the weekend again. "
I forgot to mention that she has a PC at her house that she also syncs to. Would this cause a problem. I am already getting that pop up saying that the iPod is synced to another library (even though she is signed in with her Apple ID to iTunes) and gives the pop up to Cancel, Erase & Sync, or Transfer Purchases. My question arose because she clicked on "Erase & Sync" by mistake when she plugged the iPod to her PC the first time. When the iPod was purchased and setup, it was synced to my PC first. When she went home, she hooked it up to her PC and then she erased it by accident. I was able to restore all the missing stuff yesterday using my PC. However, even after doing that it still told me the next time I hooked it up last night that the iPod was currently synced with a different library. Hopefully, you can help me understand all this. She wants to sync her iPod and also backup her iPod at both places. Both PCs have been authorised. Thanks

How can i use my account without the billing info, as i do not have a credit card. and my shipping and billing info is under US. i'm in singapore. how do i change this?

how can i use my account without the billing info, as i do not have a credit card. and my shipping and billing info is under US. i'm in singapore. how do i change this?

If you are just visiting Singapore, then leave the account as it is. If you have moved there, then view your account using the iTunes app on a Mac or PC and change the country/region to your current location and address. If you do not have a bank card, you can fund your account using iTunes gift cards if available in Singapore.

How can I use one photo twice in a slideshow

I am in iPhoto '11 9.4.3 making a slideshow to send to iDVD for my mother-in-laws funeral next Wednesday.
How can I use this one particular photo of her several times in the slide show.
I have tried copy/past and that does not seem to work.
Thanx in advance

I would just duplicate the picture several times and keep inserting duplicates ...

How can a BILBO can be used as a pseudo-ran​dom pattern generator.​(using labview)

Similar Messages

Maybe you are looking for

How can a BILBO can be used as a pseudo-random pattern generator.(using labview)