How can I simultaneously acquire and display an image on the front panel using a PCI-1424

Dear friends;
I want to use PCI-1424  , and labview 5.1 to capture the image,  But I can not find some functions in labview to capture, display and save the image.Can you be kind to share some examples or provide some information.
Another question is how I CAN display the image in the front panel.
thanks so much

Hello yangshang,
Thank you for contacting National Instruments!  To acquire images from the 1424 you will need NI IMAQ 2.5.1 or later.  This can be found HERE on our drivers download page.  One thing to note is that in LabVIEW 5 we only had the ability to view an IMAQ image as a pop up window.  This VI is called "IMAQ Windraw".  This will pop up a separate window that will display your picture.  If you need to view the picture on the front panel you can try saving the image as a file (BMP, JPG, etc) then use the LabVIEW Graphics and Sound VI's to Read a picture file in and then wire the picture to a picture control on the front panel.  Let me know if you have anymore questions.  Good Luck.
Regards,
Mark T
Applications Engineer | National Instruments

Similar Messages

  • How can I simultaneously acquire and display an image on the front panel using a PCI-1408

    I have to acquire and display an image directely in the front panel of a *.vi using a PCI-1408. i have to know all informmations about this image because I want to create a calibration system.

    Hi Paola,
    if you own IMAQ Vision you can just have a look at the examples that comes with your board or you can look at: http://zone.ni.com/devzone/explprog.nsf/6c163603265406328625682a006ed37d/2abaefe05789961686256866007c0d22?OpenDocument.
    Without IMAQ Vision look at:
    http://zone.ni.com/devzone/explprog.nsf/6c163603265406328625682a006ed37d/22474456534202b086256aff005fc4f3
    (or search at ni.com for "IMAQ Display without IMAQ Vison)
    Please mail me if you need further help,
    Michael

  • How can I transfer photos and videos from iPad to HTC one X using wi fi?

    How can I transfer photos and videos from iPad to HTC one X using wi fi?

    There are apps that will do this as well.
    http://www.wirelesstransferapp.com

  • How do I programmatically display jpeg files on the front panel

    Hi,
    I would like to be able to programmatically display various jpeg images on the front panel of a VI. I would mostly like to be able to display one image at a time and have the ability to programmatically change the image to different ones under program control. I found a picture indicator but not sure how to use if or if this is the best way. Thanks for any help.
    Dave Adams

    Yes, you can use a picture indicator.
    The attached simple codelet shows how to display a jpeg image on it (Make sure the image indicator is big enough).
    Let us know if you need help with the rest of the coding.
    LabVIEW Champion . Do more with less code and in less time .
    Attachments:
    DrawJpeg.gif ‏2 KB

  • How can I get a reference to all controls on a front panel of one type )for example of the type Text Ring?

    I'd like to set the strings[] property of all the Text Ring controls on a front panel at once without creating a property node for every text ring. How can i do that?

    > How can I get a reference to all controls on a front panel of one type
    > )for example of the type Text Ring?
    >
    > I'd like to set the strings[] property of all the Text Ring controls
    > on a front panel at once without creating a property node for every
    > text ring. How can i do that?
    This is likely more complicated than making property nodes for each
    ring, but you can do it. Make a subVI that takes in a panel reference,
    reads the array of control references, loops through them looking for
    rings, and modifying the Strings[] property on each ring.
    The part of this that will probably be the least obvious, when you
    have an array of control references there are two ways to find out
    if an element is a ring. You can read the classID and compare it
    to the cla
    ssID of a true ring control. An alternative is to cast
    the control reference to a ring control using a Cast to more specific
    node and wire the error out to a case structure. The error case is
    where the objects that aren't rings will go. The success case case
    where you will have a valid ring refnum that you can use to modify
    the strings.
    Greg McKaskle

  • How can I view acquired images on the front panel?

    Hi, I would like view captures on the front panel and video images, Is possible to do it? How can I do it?
    Thank's everybody!

    Hi,
    Its pretty simple, go to Edit>Import picture from file (browse for your .jpeg/.bmp/.gif etc file)
    again Edit>Paste
    hope this helps.

  • How can i stop Pages and Numbers JUMPING ALL OVER THE SCREEN. MAKING ME SEASICK! PLEASE HELP

    how can i stop Pages and Numbers  screen JUMPING ALL OVER the place when i just touch my mouse. i have tried and tried to change the mouse settings - but it is the software. especially Numbers. you can't even see what the page size is until you print. i am so SEASICK! PLEASE HELP.

    Thanks for the trouble to reply. this problem only happens with Pages and Numbers for me. i have done all the tricks like restarting. the main problem is that the working space is not 'stable' - it has no 'ends' even on full screen. in Numbers - UNLESS I SET IT TO 25% VIEW (which is way too small) - the actual total 'work space' is way off the grid - so every time i move the mouse the table i am working on zooms off to left or right, at the slightest touch. i have set my mouse to no gestures!
    the thing is this did not happen before the latest upgrades.
    but thanks anyway. SG.
    if you are a techy person - i have another prob. in Mail i am unable to set the SORT / VIEW messages to BY DATE.
    (it used to be ok, at one time, too). now it continually reverts to BY SUBJECT oh so annoying !
    restarting etc does not change it. resetting preferences does not change it.
    maybe i need a new Mac ?
    mine is a 27-inch, Mid 2011. running latest.

  • Can I embed an aquired image in the front panel or does it have to be in its own window?

    I need to be repeatedly displaying processed images and I know that I can make the image window "float" so that it is always on top and never becomes hidden when I click in the vi's front panel, but it is inconvenient that if I move the vi window or scroll within it, the image window stays where it is. I would like the image display to be a part of the front panel if that is possible, so that both move together.
    Thanks

    This is fairly simple to do.
    I have attached Make IMAQ Child.vi, which is a slightly modified version of one I originally found on the NI website.
    One required input is the filename of the parent VI, which can easily be obtained by using the "Current VI's Path" constant and Strip Path to remove the filename from the path.
    The other required input is the IMAQ window number.
    This will make the IMAQ window a child panel within the specified parent window. It will move with the parent window.
    Bruce
    Bruce Ammons
    Ammons Engineering
    Attachments:
    Make_IMAQ_Child.vi ‏39 KB

  • Image of the front panel and block diagram

    Hi,
    I need to get some info from the block diagram but I don't have labview in my computer. can some one please open it and post a picture of both front panel and block diagram.
    It may not open properly, but that is okay.
    Thanks,
    Sujay.

    Here you go

  • How can i display 7 segment dispay on front panel using any kind of input

    Hi,
    I need help..!! I need to dispay the numeric data in 7 segment format. Is it possible to do in labview?

    you need to display the number onto a 7 segment display?
    i think you would need sometype of microcontroller board like the AVR or the aurdino. and use the visa usb port to display out into the 7 segment display.
    i am new to this too. but that's what i would do.
    i hope someone with more expertise can  give better advice.
    Arduino and 7 Segment LED
    7 Segment LED
    The
    seven segment display is a pretty simple device.  Its actually just 7
    LEDs (8 really including the decimal point) arranged so different
    combinations can be used to make numerical digits.  This tutorial will
    show you how to wire one up and drive it with an Arduino.
    Message Edited by krispiekream on 07-23-2009 11:48 AM
    Best regards,
    Krispiekream

  • My Wifi reception is now weak after removing mackeeper, how can I fix it and is it related to the removal of mackeeper?

    My macbook pro Wifi worked fine for a long while with the same router in place. I loaded mackeeper on my machine and had no problems until the license expired. I when through the steps to remove mackeeper, the Wifi went then from not working at all to working with very poor reception. All other devinesin house have no problem finding and connecing to our network. I can even see the neighbors networks on all devices.
    My macbook pro running mavrick can not see any network unless I'm rigth on top of the router.
    What can I do.

    Start up in Recovery mode. In the OS X Utilities screen, select Get Help Online. A clean copy of Safari will launch. No plugins, such as Flash, will be available. While in Recovery, you'll have no access to your saved bookmarks or passwords, so make a note of those before you begin, if they're needed for the test.
    Test. After testing, restart as usual and post the results.

  • How can I get IP and hots names of all the machines.....

    I need to get the IP addresses and host names of all the machines in my netowrk and need to select only is a HP / Compaq x86 machines finaly.
    If you know atleast a part of this please help me.
    [email protected]

    You coulduse the broadcast address (x.x.x.255) in an ICMP sweep to determine which hosts are alive (and accepting ICMP).
    But no, there's not a single (and definitive / sure) way to retrieve all IP addresses.

  • How can I get my SVG to show up in the browser? Using Adobe Muse.

    I created an SVG in Adobe Illustrator CC with all the recommended settings (yes, I unchecked "Responsive"), and then placed it in my website in Muse CC, and it does not appear on my website.  It just shows a broken photo link icon where the image is supposed to be.  I thought that at the very least, it would show the PNG image since it is supposed to automatically create the PNG. 
    It appears perfectly in Muse's Preview mode.
    Any advice?  Attached are images of the SVG settings I use, and how it is appearing in the browser.
    Here's a link to the live site in case you want to take a look: design.mattgrajcar.com (I may have reverted back to just putting a PNG in for the time being).
    Thanks!

    This may be caused by your hosting provider not having the proper MIME file to display .svg files.
    See link.
    http://css-tricks.com/snippets/htaccess/serve-svg-correct-content-type/

  • How can I publish a tablet size only app to the android market using Flash CS5.5?

    I've developed an app to run on a tablet and would like to sell it in Googles Android Maket.    I uploaded the .apk file to the android market however, the settings indicate that the app will work on small to large screen sizes.
    Is there anyway I can specify that the app is only suitable for large (tablet) size devices?  I believe there are some tags in the <manifest> section, which I think must be part of the .apk package Flash creates.
    <supports-screens
    android:smallScreens="true"
    android:normalScreens= "true"
    android:largeScreens="true"
    android:xlargeScreens="true"
    android:anyDensity="true" />
    Can I alter these tags manually somewhere or is there some other way to specify the device size?

    If you publish folio as Public/free then it will appear in app library and users can download folio and read folio content. You can test folio in ACV.
    If you publish folio as Public/retail then it will only appear in library once associated in-apppurchase is approved by Apple. You can test folio in developer.ipa.
    Woraround: You can create test app and keep title id as your application account in whch you published your folio and test developer.ipa. If folio is working fine in test app then publish it in LIve app.

  • How can I import NEF and JPEG in Aperture at the same time from my D200

    I have my D200 and shoot in RAW and JPEG.
    why is it when I import in the library that I only see the NEF files and not the JPEG.
    I want to import both the extensions, because I shoot all my pictures in RAW and JPEG and I only want to store the 4 and 5 stars rated pictures in NEF and lower rating I want to store just as JPEG.
    Thanks for any help, Frank

    You assume that I speak and write Dutch.
    My apologies to all of you who don't/cannot read/understand Dutch. The following is in Dutch and not Double Dutch.
    It explains in some detail how to setup a workflow in Automator for separating RAW and JPEG files and importing the result in Aperture.
    If someone wants the explanation in English: post a message.
    Ga naar
    http://www.completedigitalphotography.com/?p=408#more-408
    en haal de Separate Jpeg's action.
    NB. Ik ken alleen de Engelse namen van de mappen.
    Plaats de Separate Jpeg's action hier
    ~/Library/Automator
    Automator
    Automator opstarten
    Kies Bestand, Nieuw
    Paneel Library: selecteer Finder
    Paneel Action : selecteer een sleep "Separate Jpeg's" naar Workflow paneel
    selecteer en sleep "Get Folder Contents" naar Workflow paneel (einde)
    Paneel Library : selecteer Automator (PAS OP: Automator wordt geladen; weg ermee)
    Paneel Automator: selecteer en sleep Import Photos naar Workflow paneel (einde)
    Opslaan als Finder Plugin in de map
    ~/Library/Workflow/Applications/Workflows/
    Gebruik
    Selecteer een map in Finder die RAW and JPEG bevat.
    Ctrl-Click of rechts klikken
    In het context menu navigeer naar Automator
    Selecteer Separate JPEG's
    De rest gaat nu automatisch
    Succes
    Berend

Maybe you are looking for