How do I select the AX green light to flash on data?

I am using Airport Utility 6.2 on a MBA in a network consisting of a 4th Gen AE extended by a 1st Gen AX and I cannot seem to find the option to change the AX green light to flasj on data. What am I missing?

AirPort Utility 6.2 does not provide this type of feature.
If you install AirPort Utility 5.6, you could use that version to set up the AirPorts to flash green on activity. AirPort Utility 5.6 was designed to run on the Lion operating system. You will need to use a workaround mentioned in the link below if you want to install AirPort Utility 5.6 on Mountain Lion, since Apple's installler will not allow you to do this.
This is not supported by Apple. It does work for me as well as others, but there is no way to predict whether it might work for you.
http://www.macworld.com/article/1167965/mountain_lion_and_the_ancient_airport_ba se_station.html

Similar Messages

I have lost the amber/green light indicator on AirPort Express. How canI get it back?

How can i get the amber/green light indicator on the AirPort Express. It has stopped working.

If I do a factory reset, will I have to reset the network configuration?
Yes, but based on what you are telling us, I doubt that the device will restart after you try this. You have tested with other AC wall jacks, correct?
I just purchased the unit in April this year, it would be very soon to have to replace it, especially since I don't think I kept the receipt...
Most stores keep a record of purchases. Otherwise, Apple support can look at the serial number and know approximately when the device was sold. You should have no problem getting a replacement, I would imagine.

How do I select the entire text when the focus is moved to one TextBox?

How do I select the entire text when the focus is moved to one TextBox?
There are three TextBoxes. I use <TextBox TabIndex="1"/> to set the order they are selected. When I enter one specific TextBox, I would like to have the entire text selected ... one key stroke removes all of the text in that TextBox.
bhs67

I do it the following way:
1. Override the OnStartup for the application. Use the following code: (VB.NET)
EventManager.RegisterClassHandler(GetType(TextBox), TextBox.GotFocusEvent, New RoutedEventHandler(AddressOf TextBox_GotFocus))
2. In the event handler use this code (again VB.NET)
Private Sub TextBox_GotFocus(ByVal sender As Object, ByVal e As RoutedEventArgs)
_theTextBox = CType(sender, TextBox)
If setFocusTimer IsNot Nothing Then
RemoveHandler setFocusTimer.Tick, AddressOf setFocusTimer_Tick
End If
setFocusTimer = New DispatcherTimer
setFocusTimer.Interval = TimeSpan.FromMilliseconds(10)
AddHandler setFocusTimer.Tick, AddressOf setFocusTimer_Tick
setFocusTimer.Start()
End Sub
Private Sub setFocusTimer_Tick(ByVal sender As Object, ByVal e As System.EventArgs)
setFocusTimer.Stop()
_theTextBox.SelectAll()
End Sub
What this does is register a handler for every textbox in your application. This will execute when the GotFocus event is raised and will allow you to do whatever (in this case select all) you want. A great way of handling things at the application
level.
Lloyd Sheen

I'm trying to install an update to itunes that downloaded but can't complete installation as its trying to install onto D: drive. I don't have a D drive and i'm not given option of selecting the drive to install on. How can i select the drive that i want

I'm trying to install itunes but can't complete installation as its trying to install onto F: drive. I don't have a F drive and I'm not given option of selecting the drive to install on. How can I select the drive that i want to install on?

Hi,
How do you connect the printer to the XP machine ? If USB, you need to make that machine as a Print server. Please try this:
http://techtips.salon.com/make-windows-computer-print-server-11914.html
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

I'm trying to print from a full size 30x42 pdf of an AutoCAD file. I only want to print an 8 1/2 x 11 portion, in scale. How do I select the window and print in scale on my 8 1/2 x 11 printer?

I'm trying to print from a full-size, 30x42 pdf of an AutoCAD file. I only want to print an 8 1/2 x 11 portion, in scale. How do I select the window and print in scale on my 8 1/2 x 11 printer (Brother MFC-9340CDW)?

You might be better off contacting an AutoCAD support group.

How can i select the next column instead of next row when press enter key

I need to know how can i select the next column instead of next row when i press the enter key.By default ,when i press enter key the next row is selected and the column remain unchanged but I wants opposite that is the row should remain unchanged but column index will changed.
Thanks to all.

Well, the right arrow key will already move you to the next column, so the easiest way to do this is to modify the InputMap to have the Enter key invoke the same Action as the right arrow key.
You can search the forum for my "Table Actions" (without the space) example that will show you how to do this.

How do I enable the big green battery and the plug icon? (R61 - Win7 64)

I know that this subject is pretty old, but maybe somebody will answer.
I have a reverse problem from:
http://forums.lenovo.com/t5/T61-and-prior-T-series-ThinkPad/How-do-I-remove-the-big-green-battery-an...
I do not have this green battery and the plugin icon, instead I have gray battery like this:
Strange thing is that it is resistant to any changes in Power Manager Advanced Options - whatever I check: hide, show, small icon, big icon - it stays as it is.
I use Win7 64bit.
Any ideas?
Moderator comment: New thread split from the above link. Subject and post edited to reflect new content.
Solved!
Go to Solution.

Yes, that previous page button is wonderful, isn't it LOL. It has gotten me many times. Some text editors are merciful and will preserve your work if you immediately hit the back button. The Lenovo Forum editor does not but it does autosave your draft ever so often
Concerning Power Manager: First, let's make sure of the obvious. Have you tried removing and re-installing your battery and making sure it is making good contact?
Assuming your battery is not the problem,
go ahead and uninstall "Hotkeys."
Hotkeys version 3.81.0100 currently includes 5 separate components which you will see in your list of programs:
- On Screen Display
- Thinkpad Full Screen Magnifier
- Lenovo System Interface Driver
- Lenovo Auto Scroll Utility
- Lenovo Patch Utility
Use Control Panel and make sure to un-install all of these. (You may never have installed Hotkeys. If so, skip this step Or, if you have installed a previous version which does not include all of these components, just un-install any of these you find).
Next, use Control Panel to un-install "Power Manager," and "Lenovo Power Management Driver." Yes, "Power Manager" is different from "Lenovo Power Management Driver." (It sounds like like you may never have installed "Lenovo Power Management Driver" so just skip that one if you don't see it in your list of programs.)
Tip: Older versions of "Power Manager" may be called "Thinkpad Power Manager" or "Lenovo Power Manager." We're now up to version 6.36.
Reboot as prompted during the un-installation process.
Now, go to the Lenovo Drivers and Software page here and enter your type/model number.
Install the following software in this order:
(1) First, install "Lenovo Power Management Driver" from the Power Management section.
(2) Next, install "Hotkey Features Integration" from the Software and Utility section.
(3) Finally, install "Power Manager" itself. (Version 6.36 you see there is the latest version).
Reboot as instructed during the installation process.
As for the Lenovo "anti-shock feature," install "ThinkVantage Active Protection System" from the Thinkvantage Technology section
That should do it. Let us know how you do.
Moderator comment: Subject edited to match new thread.
Have a great day. (I do not work for Lenovo)

How can I select the existing worksheet while using OLE2 to open the template workboo

Source:
application:=ole2.create_obj('Excel.Application');
workbooks:=ole2.get_obj_property(application,'Workbooks');
args := ole2.create_arglist;
ole2.add_arg(args, 'c:\RptTemplate.xlt');
workbook:=ole2.invoke_obj(workbooks,'Open',args);
ole2.destroy_arglist(args);
worksheets:=ole2.get_obj_property(application,'Worksheets');
args := ole2.create_arglist;
ole2.add_arg(args, 'Sheet1');
worksheet :=ole2.invoke_obj(worksheets,'Select',args);
ole2.destroy_arglist(args);
Problem:
1. While executing the above code, error -305500 occurs after executing "worksheet := ole2.invoke_obj(worksheets','Select',args)". How can I select the sheet i wanted in the template ??
2. As I refer to the forms on-line document, it stated that the ole2 programmers documentation can provide all object types and methods that can be used with the OLE2. Does any link can provided to download the specified documentation ??

The error is probably that your Worksheets variable is actually empty. Looking at your code I think the problem is that you try and get the value of the worksheets collection from the application then you should try and get it from the Workbooks object.

I have an 8500a how, once I select the apps I want and add to the printer. How do i get them to wor

I have an 8500a how, once I select the apps I want and add to the printer. How do i get them to work? And is it always this slow....

Hey jmknights!
While I can't speak to how quickly the apps will work, I may be able to help you with how they work. Once you have the apps added to the printer you would select the app you want to print from on the printer's front panel. Once inside the app, select what you want to print and if all goes as it should, the printer should begin printing the requested information within a few seconds.
Hope this helps!
If I have solved your issue, please feel free to provide kudos and make sure you mark this thread as solution provided!
Although I work for HP, my posts and replies are my own opinion and not those of HP.

How do I select the type of paper I want to use in iphoto11 on an Epson 2200?

How do I select the type of paper I want to use in iphoto11 on an Epson 2200?

You should have something like this:
Click to view full size
So if you don't see any of those printer specific settings you should reinstall the print driver for your printer as Larry suggested.
OT

How do i select the "submit" after i enter my wireless passwork on the tv screen for apple tv setup?

how do i select the "submit" from the remote after i enter my wireless password on the tv screen for apple tv set up?

The 5 digit code is every time different. That does not matter. Just integrate every device into your network.
You can connect many computers to Apple TV but syncronisation works exactly with one computer. That's why I use "streaming". But you can sync one computer, then another, and so on. The content on your Apple TV is the content from your computer that has synced last. But you can not mix it.
The new Apple TV has no syncronisation. Everything is streamed,
Regards,
Torsten,
Germany

CS3 - Place Word document: How can I select the current preset?

Hi
In my Plugin I like to place a word document into a text frame. To do this I want select a defined preset before.
How can I do that?
How can I select the current preset for the placement (import)?
Thanks for the support
Hans

Hi,
I had posted a similar query few days back to place excel file in text frame. And I found out that, it is not possible to specify formatting option for any of microsoft document when using Indesign SDK.
But we can do this by running script.
If you are able to specify the formatting option through script, write code to get script object & execute this script through Indesign SDK.
I was able to specify formatting option, sheet number, range etc through this.
Hope this helps.
Rajani

I have a iphone 5 and i can not figure out how to turn on the LED notification light. is this even possable? if not how do i know if i missed a call when i was not there to answer it visualy

I have a iphone 5 and i can not figure out how to turn on the LED notification light. is this even possable? if not how do i know if i missed a call when i was not there to answer it visualy

If you were not there, how would you see the led?
Anyway missed calls will appear on your Lock screen under the Missed tab.
Or a small red numbered badge will appear on the Phone App icon when you have missed calls. You can then access the Recents Tab in the Phone App to see whcih calls were missed.
Missed Calls are shown in red there

How do I select the items based on their adjacent equality?

In the below table,
DECLARE @t1 TABLE(id INT,NAME VARCHAR(MAX))
INSERT INTO @t1 VALUES(1,'test')
INSERT INTO @t1 VALUES(2,'test')
INSERT INTO @t1 VALUES(3,'best')
INSERT INTO @t1 VALUES(4,'rest')
INSERT INTO @t1 VALUES(5,'rest')
how can I select the records that have equals values coming adjacently? That is I am running an SQL job. It should take the adjacent equal value count for its processing. In the below table, first time the job is running it should take count as 2 the
2nd time job is running it should be 1. Third time it should be 2. What is the query that will fetch the cont of equal records for name column? In case no equal columns it should be 1. Please help
mayooran99

Hi
Try the following code.
DECLARE @t1 TABLE(id INT,NAME VARCHAR(MAX))
INSERT INTO @t1 VALUES(1,'test')
INSERT INTO @t1 VALUES(2,'test')
INSERT INTO @t1 VALUES(3,'best')
INSERT INTO @t1 VALUES(4,'rest')
INSERT INTO @t1 VALUES(5,'rest')
INSERT INTO @t1 VALUES(6,'test')
INSERT INTO @t1 VALUES(7,'best')
INSERT INTO @t1 VALUES(8,'best')
INSERT INTO @t1 VALUES(9,'vest')
--ranking adjacent names, running total
SELECT rs.id, rs.NAME, ROW_NUMBER() over (partition by name, nxt_id order by id) RankingCount
FROM (
SELECT nxt.id, nxt.NAME,(SELECT min(s.id)
FROM @t1 s
WHERE s.name <> nxt.name
AND s.id > nxt.id
) as nxt_id
FROM @t1 nxt) rs
ORDER BY rs.id;
--code to just return the totals
with cteTotals
as
SELECT rs.id, rs.NAME, ROW_NUMBER() over (partition by name, nxt_id order by id) RankingCount, nxt_id, ROW_NUMBER() over (partition by name, nxt_id order by id desc) Ranking
FROM (
SELECT nxt.id, nxt.NAME,(SELECT min(s.id)
FROM @t1 s
WHERE s.name <> nxt.name
AND s.id > nxt.id
) as nxt_id
FROM @t1 nxt) rs
select Name, RankingCount
from cteTotals
WHERE Ranking=1
order by id
The first query keeps a running total of adjacent names, the second one just reports the totals

How do I select the correct ram for upgrade to iMac 8,1?

How do I select the correct ram for upgrade on my iMac 8,1? When I look up information online, I believe that I have SO-DIMM ram. Do I need to purchase SO DiMM? I want to upgrade to Maverick and I think I was told that I need DDR2 or SDRAM. My model # is A1224, if that helps.

Welcome to Apple Support Communities
OS X Mavericks requires 2 GB of RAM at least, but I recommend at least 4 GB of RAM.
You have got an Early 2008 iMac. You can buy more RAM at OWC or Crucial. Your Mac supports 6 GB of RAM

How do I select the AX green light to flash on data?

Similar Messages

Maybe you are looking for