How do I wake up Dell Inspiron 6400 after closing the lid? [SOLVED]
I'm running Arch on a Dell Inspiron 6400 laptop (same as Inspiron e1505). When I close the top to an angle of less than about 30 degrees, the machine goes into some kind of sleep state and Arch is suspended (black screen, no response to anything). It may be easy to wake up Windows from such a condition but what must I do get Arch back and working, short of having to reboot?
Last edited by RobF (2007-07-05 20:08:41)
thayer.w wrote:
RobF, it's hard to say, without knowing what your setup is... GNOME, KDE? Any power management software installed such as Powersaved or hibernation scripts?
If you're still having troubles with it, check out the Inspiron 6400 wiki I've been working on. It includes step-by-step instructions on setting up hibernation/suspend features and I can verify it works on my own 6400.
http://wiki.archlinux.org/index.php/Dell_Inspiron_6400
I'm using KDE, and I haven't specifically installed any power management software aside from what came with the Arch base install and KDE.
I went through your Dell Inspiron 6400 Wiki (great work! I'll add to it) and installed acpid and powersave and hoped to install kpowersave or kpowersave-devel but neither of these will compile. kpowersave requires unsermake-svn but unsermake-svn will not compile because of the error: "unsermake-svn is not available for the 'i686' architecture," and: "Note that many packages may need a line added to their PKGBUILD such as arch=('i686')." So much about that.
Trying to build the package kpowersave-devel also aborts with the error:
Checking for Qt... configure: error: Qt (>= Qt 3.2 and < 4.0) (headers an ..... r installation!
For more details about this problem, look at the end of config.log.
make: *** No targets specified and no makefile found. Stop.
==> ERROR: Build Failed. Aborting...
So much about that.
About kpowersave-devel, srabd commented a month ago: "It doesn't compile now, but compiles if you use unsermake instead of make in the two final lines." Wonderful! But as I reported above, "unsermake-svn is not available for the 'i686' architecture."
I seem to be stuck. Any ideas how I can get around this?
Robert
Similar Messages
-
How to Direct control to application's window after closing the popup?
Hi,
I am using 10.1.3. In my application I am unable to direct control to application's window after closing the popup, if I open any other window at the same time.
For more info see the below step:-
-> Open any popup in my application.
-> Open any new window (lets say Google.com).
-> Now restore popup on Google window.
-> Now close popup
- control goes to Google window but not the parent application window.
How to direct control to the parent window?
Can anybody help me regarding this?
Thanx...AbhijitHi Abhijit,
You can do this using Javascript alone. Below are the two sample files I created.
main.html_
<html>
<head>
<title>Testing popup</title>
<script type="text/javascript">
function openPopup() {
window.open("popup.html");
</script>
</head>
<body>
<a hr_ef="javascript:openPopup()">Open popup</a>
<input id="something" name="something" type="text" value="something">
</body>
</html>
Note: hr_ef should be href. The code tags are messing with the link.
popup.html_
<html>
<head>
<title>This is the popup window</title>
<script type="text/javascript">
function goToMain() {
window.opener.something.focus();
</script>
</head>
<body onunload="goToMain()">
This is the popup window. Close this window to return to main window.
</body>
</html>The idea is to call a javascript function in the popup window that tries to focus on an object (eg. InputText) in the main html.
Although, one point to take note is the naming of html objects by by these ADF UI Components. If you named your form id as "*form1*" and input text id as "*something*", your input text id will end up as "*form1:something*".
Therefore, you will have to tweak the code above to the following:
<script type="text/javascript">
function goToMain() {
window.opener.form1['form1:something'].focus();
</script>Regards,
Chan Kelwin -
Slow wake after closing the lid
Hi there everybody.
My macbookpro has a very slow wake up after I close-open the lid with enough battery to continue working. It shows the “washed” screen in the background and the progressive bar of light squares in the front, as when the computer rans out of battery and you replug it a demand it to rewake from NObattery sleep.
I'd really appreciate your comments on this problem.
Here's a report from etrecheck so you can have details to help me figure out what's going on:
EtreCheck version: 2.1.8 (121)
Report generated 25 de marzo de 2015 11:08:07 GMT-04:30
Hardware Information: ℹ️
MacBook Pro (13-inch, Mid 2012) (Technical Specifications)
MacBook Pro - model: MacBookPro9,2
1 2.9 GHz Intel Core i7 CPU: 2-core
8 GB RAM
BANK 0/DIMM0
4 GB DDR3 1600 MHz ok
BANK 1/DIMM0
4 GB DDR3 1600 MHz ok
Bluetooth: Good - Handoff/Airdrop2 supported
Wireless: en1: 802.11 a/b/g/n
Battery Health: Normal - Cycle count 147
Video Information: ℹ️
Intel HD Graphics 4000 - VRAM: 512 MB
Color LCD 1280 x 800
System Software: ℹ️
OS X 10.8.3 (12D78) - Time since boot: 44 days 13:40:7
Disk Information: ℹ️
APPLE HDD ST750LM022 disk0 : (750,16 GB)
disk0s1 (disk0s1) <not mounted> : 210 MB
Macintosh HD (disk0s2) / : 749.30 GB (458.70 GB free)
Recovery HD (disk0s3) <not mounted> [Recovery]: 650 MB
MATSHITADVD-R UJ-8A8
USB Information: ℹ️
Apple Computer, Inc. IR Receiver
Apple Inc. BRCM20702 Hub
Apple Inc. Bluetooth USB Host Controller
Apple Inc. Apple Internal Keyboard / Trackpad
Apple Inc. FaceTime HD Camera (Built-in)
Thunderbolt Information: ℹ️
Apple Inc. thunderbolt_bus
Configuration files: ℹ️
/etc/sysctl.conf - Exists
Gatekeeper: ℹ️
Anywhere
Adware: ℹ️
Geneio [Adware! - Remove]
Kernel Extensions: ℹ️
/System/Library/Extensions
[not loaded] com.ZTE.driver.ZTEUSBCDCACMData (1.3.25) [Click for support]
[not loaded] com.ZTE.driver.ZTEUSBMassStorageFilter (1.3.25) [Click for support]
[not loaded] com.blackmagic-design.desktopvideo.iokit.driver (9.9.5 - SDK 10.7) [Click for support]
[not loaded] com.blackmagic-design.desktopvideo.iokit.framebufferdriver (9.9.5 - SDK 10.7) [Click for support]
[not loaded] com.blackmagic-design.desktopvideo.multibridge.iokit.driver (9.9.5 - SDK 10.7) [Click for support]
[not loaded] com.devguru.driver.CDFree (0.5.0) [Click for support]
[not loaded] com.devguru.driver.DevGuruMdm (0.5.0) [Click for support]
[not loaded] com.devguru.driver.DevGuruRoot (0.5.0) [Click for support]
[not loaded] com.devguru.driver.DevGuruVsp (0.5.0) [Click for support]
[not loaded] com.driver.JRDMassStorageDriver32 (1.0.1) [Click for support]
[not loaded] com.driver.JRDMassStorageDriver64 (1.0.1) [Click for support]
[not loaded] com.driver.JRDUSBModemData32 (1.0.0) [Click for support]
[not loaded] com.driver.JRDUSBModemData64 (4.0.7) [Click for support]
[loaded] com.nvidia.CUDA (1.1.0) [Click for support]
/System/Library/Extensions/DeckLink_Driver.kext/Contents/PlugIns
[not loaded] com.blackmagic-design.desktopvideo.firmware (9.9.5 - SDK 10.7) [Click for support]
Startup Items: ℹ️
CUDA: Path: /System/Library/StartupItems/CUDA
HWNetMgr: Path: /Library/StartupItems/HWNetMgr
HWPortDetect: Path: /Library/StartupItems/HWPortDetect
Startup items are obsolete in OS X Yosemite
Problem System Launch Agents: ℹ️
[failed] com.apple.AirPlayUIAgent.plist
Launch Agents: ℹ️
[running] com.blackmagic-design.DesktopVideoFirmwareUpdater.plist [Click for support]
[loaded] com.google.keystone.agent.plist [Click for support]
[loaded] com.nvidia.CUDASoftwareUpdate.plist [Click for support]
Launch Daemons: ℹ️
[loaded] com.adobe.fpsaud.plist [Click for support]
[loaded] com.blackmagic-design.desktopvideo.XPCService.plist [Click for support]
[running] com.blackmagic-design.DesktopVideoHelper.plist [Click for support]
[running] com.blackmagic-design.streaming.BMDStreamingServer.plist [Click for support]
[running] com.edb.launchd.postgresql-8.4.plist [Click for support]
[loaded] com.google.keystone.daemon.plist [Click for support]
User Launch Agents: ℹ️
[loaded] com.genieo.completer.download.plist [Adware! - Remove]
[running] com.genieo.completer.update.plist [Adware! - Remove]
[running] com.spotify.webhelper.plist [Click for support]
User Login Items: ℹ️
iTunesHelper Aplicación (/Applications/iTunes.app/Contents/MacOS/iTunesHelper.app)
Internet Plug-ins: ℹ️
googletalkbrowserplugin: Version: 5.40.2.0 - SDK 10.8 [Click for support]
FlashPlayer-10.6: Version: 16.0.0.305 - SDK 10.6 [Click for support]
Flash Player: Version: 16.0.0.305 - SDK 10.6 Outdated! Update
QuickTime Plugin: Version: 7.7.1
JavaAppletPlugin: Version: 14.9.0 - SDK 10.7 Check version
o1dbrowserplugin: Version: 5.40.2.0 - SDK 10.8 [Click for support]
Safari Extensions: ℹ️
Slick Savings [Adware! - Remove]
Omnibar [Adware! - Remove]
Searchme [Adware! - Remove]
Amazon Shopping Assistant [Adware! - Remove]
Ebay Shopping Assistant [Adware! - Remove]
Audio Plug-ins: ℹ️
DVCPROHDAudio: Version: 1.3.2
3rd Party Preference Panes: ℹ️
Blackmagic Desktop Video [Click for support]
CUDA Preferences [Click for support]
Flash Player [Click for support]
Time Machine: ℹ️
Time Machine not configured!
Top Processes by CPU: ℹ️
9% WebProcess
4% WindowServer
3% Safari
1% hidd
0% fontd
Top Processes by Memory: ℹ️
768 MB WebProcess
610 MB firefox
129 MB soffice
112 MB Safari
103 MB iTunes
Virtual Memory Information: ℹ️
3.43 GB Free RAM
2.75 GB Active RAM
824 MB Inactive RAM
1.59 GB Wired RAM
7.85 GB Page-ins
2.66 GB Page-outsRemove installed adware.
1. Use free AdwareMedic to remove adware
http://www.adwaremedic.com/index.php
Install , open, and run it by clicking “Scan for Adware” button to remove adware.
Once done, quit AdwareMedic.
or
Remove the adware manually by following the “HowTo” from Apple.
http://support.apple.com/en-us/HT203987
2. Safari > Preferences > Extensions
Turn those off and relaunch Safari.
Turn those on one by one and test.
3. Safari > Preferences > Search > Search Engine :
Select your preferred search engine.
Restart the computer once in a while. 44 days without restarting? -
Windows can't wake up after closing the lid of a MBP?
My Windows XP can't wake up after I close the lid of my MBP. When I open the lid, the screen is black and the latch light is out.
I cannot solve your problem but I did have the same problem which has now evolved into my computer NEVER going to sleep and my bluetooth does not work I have tried all the advice I can find and nothing works. Of course my waranty expired four months ago so now I will have to come up with the money to fix it if I want this resovled. If your warenty is still good I suggest having someone look at it before it evloves into a bigger problem.
-
Hi, does anyone use archlinux on a dell inspiron 6400? Do you have any advice on how to speed up the boot, and configure the machine for best performance? Actually, i don't have any problem or so, just wondering howto increase my system perfomance and remove any kind of useless stuff to speed up my machine a bit
Did you read this wiki article?
http://wiki.archlinux.org/index.php/Max … erformance
Not specific to your machine, but contains some general hints. -
[Solved]No Ethernet or Wireless to work on Dell Inspiron 6400 E1505.
The Dell Inspiron 6400 E1505 wiki says ethernet should work out of box. It is not. I am trying to install wireless drivers. I checked fw-cutter during installation but i guess i have to install broadcom-wl along with it. Make command is not found (probably not installed) How can get ethernet connection to work?
Thanks.
Last edited by donniezazen (2011-12-23 04:04:52)Gusar wrote:We need more info about what kind of hardware is in that thing. So post the output of lscpi -nn
Sorry about that.
lspci -vnn | grep 14e4
Ethernet - Broadcom BCM4401-B0 100Base-TX [14e4:170c]
Network - Broadcom BCM4311 802.11b/g WLAN [14e4:4311]
lspci -nn
00:00.0 Host bridge [0600]: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub [8086:27a0] (rev 03)
00:01.0 PCI bridge [0604]: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express PCI Express Root Port [8086:27a1] (rev 03)
00:1b.0 Audio device [0403]: Intel Corporation N10/ICH 7 Family High Definition Audio Controller [8086:27d8] (rev 01)
00:1c.0 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port 1 [8086:27d0] (rev 01)
00:1c.3 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port 4 [8086:27d6] (rev 01)
00:1d.0 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 [8086:27c8] (rev 01)
00:1d.1 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 [8086:27c9] (rev 01)
00:1d.2 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 [8086:27ca] (rev 01)
00:1d.3 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 [8086:27cb] (rev 01)
00:1d.7 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller [8086:27cc] (rev 01)
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev e1)
00:1f.0 ISA bridge [0601]: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge [8086:27b9] (rev 01)
00:1f.2 IDE interface [0101]: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA IDE Controller [8086:27c4] (rev 01)
00:1f.3 SMBus [0c05]: Intel Corporation N10/ICH 7 Family SMBus Controller [8086:27da] (rev 01)
01:00.0 VGA compatible controller [0300]: nVidia Corporation G72M [Quadro NVS 110M/GeForce Go 7300] [10de:01d7] (rev a1)
03:00.0 Ethernet controller [0200]: Broadcom Corporation BCM4401-B0 100Base-TX [14e4:170c] (rev 02)
03:01.0 FireWire (IEEE 1394) [0c00]: Ricoh Co Ltd R5C832 IEEE 1394 Controller [1180:0832]
03:01.1 SD Host controller [0805]: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter [1180:0822] (rev 19)
03:01.2 System peripheral [0880]: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter [1180:0592] (rev 0a)
03:01.3 System peripheral [0880]: Ricoh Co Ltd xD-Picture Card Controller [1180:0852] (rev 05)
0b:00.0 Network controller [0280]: Broadcom Corporation BCM4311 802.11b/g WLAN [14e4:4311] (rev 01) -
Problem facing installing Solaris 10 on Dell inspiron 6400.
Hi,
I am facing problem in installing Solaris 10 on my Dell inspiron 6400.
It is giving "cannot find driver for screen device /isa/motherboard@1,61" error.
Please help...
Thanks In Advance
SaurabhHi all,
I've also the same problem, I tried the 11/06 but after GRUB , it hangs. HereBelow the HCL.
No Solaris Driver
No Solaris Driver
Multimedia
Intel Corporation
82801G (ICH7 Family) High Definition Audio Controller
No Solaris Driver
No Solaris Driver
Network
Intel Corporation
PRO/Wireless 3945ABG Network Connection
Solaris 10 11/06
Solaris 10 11/06
Firewire
Ricoh Co Ltd
Unknown device
hci1394
Note-1
Note-1
Network
Broadcom Corporation
BCM4401-B0 100Base-TX
bfe
Solaris 10 11/06
Solaris 10 11/06
Video
Intel Corporation
Mobile 945GM/GMS/940GML Express Integrated Graphics Controller
vgatext
Solaris 10 11/06
Solaris 10 11/06
Storage
Intel Corporation
82801GBM/GHM (ICH7 Family) Serial ATA Storage Controller IDE
pci-ide
Solaris 10 11/06
Solaris 10 11/06
USB
Intel Corporation
82801G (ICH7 Family) USB UHCI #1
uhci
Solaris 10 11/06
Solaris 10 11/06
USB
Intel Corporation
82801G (ICH7 Family) USB UHCI #2
uhci
Solaris 10 11/06
Solaris 10 11/06
USB
Intel Corporation
82801G (ICH7 Family) USB UHCI #3
uhci
Solaris 10 11/06
Solaris 10 11/06
USB
Intel Corporation
82801G (ICH7 Family) USB UHCI #4
uhci
Solaris 10 11/06
Solaris 10 11/06
USB
Intel Corporation
82801G (ICH7 Family) USB2 EHCI Controller
ehci -
How to install imac in dell inspiron n5040
how to install imac in dell inspiron n5040?
Are you referring to installing Mac OS X in a dell computer? If so, it isn't possible.
-
Ipod to Dell Inspiron 6400 problems
Hello
I am trying to connect my 4th gen Ipod to my new Dell Inspiron 6400 laptop and connecting it just makes the pc become very slow. If i wait long enough (an hour or so) it'll come up with Itunes which says the ipod needs formatting, but then crashes as it loads the ipod updater. The Ipod will still work with my old desktop but i want to transfer it to the laptop.
Does anyone know why this is happening? I spoke with Dell and they said i needed to get a fix from Apple, but i can't seem to find anything on the website.
Any help would be appreciated
MarkDid you read this wiki article?
http://wiki.archlinux.org/index.php/Max … erformance
Not specific to your machine, but contains some general hints. -
How can i unlock my dell laptop if i forgot the administrator password?
Dear Sir,
I forgot my dell laptop administrator password and locked out of the laptop, now i have to use my laptop to finish the home work, how can i unlock my dell laptop if i forgot
the administrator password?
Thanks in advance!Forgot dell laptop administrator password? It would be very frustrated if you are urgent to use the laptop but locked out of it.
Here are the methods
how to unlock dell laptop forgot password. I hope it will be helpful for you.
Method 1: Reset password on your dell laptop with password reset disk
This method only works when you have
created a password reset disk before you forgot password.
<1>. On your dell laptop logon screen, press
Enter directory, and then a password incorrect hint pups up, click on
OK to close it.
<2>. Click
Reset password… bellow the password text box.
<3>. When the password reset wizard appears, click
Next.
<4>. Insert the password reset disk, click
Next.
<5>. Type in
new password, and the new password hint, click
Next, click Finish.
<6>. Then you can login with the new password.
Method 2: Unlock your laptop password with Offline NT Password and Registry Editor
If you have not created a password reset disk before, you can create a live cd or bootable usb with Offline NT Password Registry Editor which is a freeware program. It is base on the text console, so it
may be a difficult to carry out.
Here are the main steps to use Offline NT password registry editor:
<1>.
Get Offline NT Password Registry Editor and use it to create a live cd or bootable usb.
<2>.
Set your dell laptop to boot with the cd or usb.
<3>. Follow the instruction to finish the operation when the password reset program starts. -
Satellite U400 does not wake up after I closed the lid
When I want to do something like go out then I close the Lid and then I can't get the laptop to wake up again, I have tried some stuff but nothing seem to work.
I don??t use Toshiba Power Save, I use the usual-normal XP energy and I even tried with Toshiba Power saver but not the software only from Start> Control Panel > but still the laptop does not wake up after I closed the Lid down.
Anyone that can help me with this issue?
thnx.These are good news but could you please post a short instruction how you have solved this? I think it would be interesting for other users here in the forum!
-
How can I prevent that emails are downloaded (POP3) when the lid of my MacBook Pro is closed?
Disable Power Nap in the Energy Saver pane of System Preferences. Uncheck the box marked Enable Power Nap... in each of the tabs.
-
I have customized my Firefox toolbar several times. After closing the browser and then reopening it, the toolbar has returned to the way it was before I customized it each time. How do I get my customization of the toolbar to become permanent?
It has occurred with Firefox 4.0.1 and 5.0see http://kb.mozillazine.org/Corrupt_localstore.rdf
Take a picture of your toolbars so you can easily reconstruct them from the default after solving the the problem.
If it happens to you it will probably happen again in the future so you might want to keep some copies of your modified localstore.rdf file so you can delete the bad one and rename one of the replacements in waiting. Saving, copying and renaming must be done with Firefox down, of course. -
iTunes 10.5.3 restarts itself after closing the program. How do I fix this?
Windows 7 64bit Ultimate
iTunes 10.5.3 64bitI've had this problem on my Windows XP for years. it's been around, unsolved, or no solutions in these forums.
It keeps reminding me why Apple will never be the primary office computer company. Anyone running a business cannot have software running that will not behave, won't shut down, or behaves without any explanation, and this problem has no explanation, or solution that I can find except to use task manager to kill the process and only use iTunes when I'm expecting to shut down or kill the process. -
How do I get back into my iPad after updating the iOS?
how do I get back into my iPad after updating the iOS?
What do you mean? Why can you not access the iPad?
Maybe you are looking for
-
IPad no longer playing ANY type of video after 8.3 upgrade
My iPad mini can no longer play ANY video. I have tried various movies/tv shows from my library and directly from iTunes. When I play a video, I get the following message "This operation could not be completed. An unknown error occurred (-16710).
-
I can no longer watch videos from email or yahoo. what has happened? and how do I fix it? Thanks Message was edited by: ConnieH1999 sorry my first question said I phone. It is my mac desk top. thanks
-
Can I add a site search box to my iWeb site?
A newspaper site that I am developing needs to have search capabilities as I am posting an archive of articles. Does anyone know how to add this without having ads run on your site? If iWeb is not capable, does anyone have a software program to sugge
-
Reinstalling Flexsync in order to troubleshoot install
I am troubleshoot an issue with our Flexsync reports not opening, we are using out of the box reports. We have sense upgraded to the Hot Patch 6.1.1.1, however is there a method to do a fresh install of flexsync application? I have gone back based
-
Trying to find out if X220 with model number 42875TU have the IPS screens
Hi, I'm trying to find out if X220's with Model Part Numbers of 4287-5TU have the IPS screens? I cant find the model through the Lenovo model search. Thanks for the help.