How to configure cat 3750 to support ssh2

hey,
I'm trying to configure, my catalyst 3750 to support sshv2 im running IOS c3750-ipbasek9-mz.122-25.SEB2.
what commands do I need to enter on the Switch? I got a pdf from cisco showing how to do it. but I don't quite understand it. Right now my switch is just using telnet. I want to configure it to support telnet, sshv1 or sshv2.
Also all the switches use tacacs as well
thanks alot!

This should do it..
aaa new-model
username cisco secret cisco
hostname
ip domain name
crypto key generate rsa (this one is interactive)
line vty 0 4
transport input telnet ssh
SSHv1 or SSHv2 is dependant on which version of the IOS you use...
Check this document:
http://www.cisco.com/en/US/tech/tk583/tk617/technologies_tech_note09186a00800949e2.shtml

Similar Messages

How to configure solaris 7 to support unicode(Arabic)

hi all,
I have a problem in configuring solaris 7 to support Unicode(Arabic). Anyone know about this pls give me the guidelines to configure the environment variables, etc.,
-Thameem.

hi all,
I found out the solution. Its working properly.
-Thameem

How to Configure CATS Profiles in order for the Hours to be posted to CO

Hi All,
I have quick question for you all, how do I configure the CATS Time Entry Profiles so as to enable me to post the Hours (Different Receiving Cost Centers & Receiving Internal Orders) to CO.
Currently I enter time using TCODE: CAT2 and a CATS Profile and Save the Timesheet.
Following which I Approve Times using CAT4.
Then when I try to transfer time to both HR and CO using TCODE: CATA time gets transferred to HR Time Management Infotypes but not to CO.
I tried a couple of other TCODES as well i.e: CAT7 & CAPS and tried posting to CO but I am getting a message saying that "NO DATA TO TRANSFER" despite there been ample data fit to be transferred to CO.
So, my question to you all is how do you handle this situation in your implementation/organization.
Looking forward to hear from you soon.
Regards,
Aslam

Hi Aslam,
Im not sure why this isnt working.
Try approving timesheets using CATS_APPR_LITE
And check whether the timesheets are approved.
Once that is done.
Run CAT7
This would post the data from CATS to controlling.
Regards,
Brinda

How to configure Oracle National Language Support for Hindi

Hello
I am Working on one library project and right now it is in foxpro.
it is working in local(hindi) language using c-dec software.Now i want to run this project using oracle national
language support.i have done lots of rnd on that but till could not get success.what's wrong with that?
Following the step i am applied for that
1 I have create the database using in8iscii character set. Because In8iscii support the Hindi Language.
2 Set the variable NLS_LANG = hindi_india.in8iscii in environment. I am using the Windows 2000 OS because
it supports the Hindi font(Mangal).
3 I am using the Oracle Developer as front end so using mangal font in front end i am able to display data
in Hindi format that's why i am selected Windows 2000 os.
4 I have done the special setting in Windows 2000 for Hindi.it is in controlpanel-regional setting-click the indic option
for india and in input locals set keyboard layout as Hindi also.
5 I also changed the Init.ora file and add the NLS_LANGUAGE = Hindi
nls_territory = india. now, I opens the database using this Init.ora file.
6 But It can't display the data in Hindi format.I could not able to display the data in Front End also.
So,pls help me in Oracle and also guide me in Linux platform also.
null

Hi Nimit,
I have tried inserting Hindi/Marathi into an Oracle database (I have tried versions 8.0.6 and 8.1.7).
I created the database using UTF8 character set. The NLS_LANG was set to AMERICAN_AMERICA.UTF8. Inserts into the database were via iSQL*Plus or import. For querying I used OCI and Pro*C. The data for my app is being served up as XML. I have not tried Developer. The DB platforms have been both HPUX and Win2K, while the client platform has been Win2K/IE5.5 SP2. I have been using Code2000 as the font.
Did you manage to view the stored data using the export utility ?
Also, you can try using yudit to edit unicode files on Linux.

How to Configure Transparent caching on Cat 6500 with CSM in bridge mode?

hi.
I found How to Configure Transparent caching on Cat 6500 with CSM in routed mode.
But,
I need help How to Configure Transparent caching on Cat 6500 with CSM in bridge mode?
Please let me know sample configuration.
thanks.

Hi,
I wrote the document you mentioned and I also wrote the one below.
http://www.cisco.com/en/US/partner/products/hw/modules/ps2706/products_configuration_example09186a00802c1201.shtml
The one with the SSLM is a bridge mode config.
If you replace the SSLM with a cache [or a farm of caches] it would be a similar config.
Replace the SSL21 vserver with an HTTP vserver [most important is to keep the vlan configured on each vserver]
Regards,
Gilles.

How to configure the database monitoring (DBA Cockpit) after Support pack

Hi,
I did the Support Pack Upgrade for BW system and i ran SGEN as well, now i need to configure the database , could you please suggest how to configure the database monitoring (DBA Cockpit) after Support Pack Upgrade.
Server is MSSQL , Component is SAP NetWeaver 2004s and OS is Windows NT.
Plesae suggest.
Chandu.

Hi,
You are right. SAP delivers this functionality from SP-12. So when you have applied the SP-12, you must have done these config steps to enable the DBA Cockpit.
If you have done these steps earlier, So you must have DBA Cockpit enable right now and putting extra SPs like 13, 14 and so on, should not be a matter.
Now if you have not performed those config steps before, Please do them now and you will be able to use DBA cockpit.
Please understand that SP12 is the base to run DBA Cockpit.
With Regards,
Saurabh

How to configure the SAP WEB AS to support SSL

Hello Gurus-
Can you please let me know how to configure the SAP WEB AS to support SSL.

Vinod,
Please read note 510007 Setting up SSL on WAS server ABAP.
This note is found under BC-SEC-SSL
Take care,
Stephen

How to configure the mail in Sales Support of SAP SD

Hi,
Experts I have one scenario in my co. that we have 300 users we have to send the mails to our 300
users for every 2 or 3 months once. Regarding new promotions (Discounts , Price changes) of
company. For this every time we are changing the sold to party in quotation and taking printouts then
sending to our users its a lengthy procedure, to avoid this long time very soon we are going to
implement SAP SD Sales Suppor in our company is there any functionality in SAP to send mail at
once to our 300 users may i know about how to configure the mail for this scenario.
Thanks and Regards
MH

Hi Prashant,
Thanks for you immediate responce, Can you give me the configuration steps in detail.
Thanks and Regards,
MH

HT1695 I use a Wifi router and I have to connect using a ppoe connection. Does iOS support that and how to configure it on aniPAD?

Does anyone know how to configure a PPOE connection?

Take a look at this thread.
http://forums.macrumors.com/showthread.php?t=914983
I think the answer is no. Not directly using ios.

How to configure Firefox to use OpenVPN?

summary: I'm running OpenVPN from a Debian client through a Debian jumpbox/server. After I [start the server, start the client] most IP-based applications (DNS, ping, ssh) seem to work from the client, but client's Firefox cannot connect to http://www.whatismyip.com/ (or any other URI). How to configure Firefox to use the VPN? or otherwise fix the problem? or further debug it?
details:
I have a laptop running debian_version==jessie/sid with Firefox version=33.0 which needs to access a compute cluster. The cluster formerly required only an SSL VPN (enabled by a Firefox plugin) to access, but now has several additional requirements, which I seek to satisfy by running the SSL VPN through a jumpbox running an OpenVPN server. The jumpbox is running a "vanilla" Debian 7.7.
I have been using the laptop successfully for a few years without network problems. Currently I have the laptop connected by wire directly to an ISP-supplied modem/router. With `openvpn` NOT running on the laptop, I see:
* `ifconfig` shows no entry='tun0' (just "the usual" entries for 'eth0', 'lo', 'wlan0'), and shows the expected client IP# bound to 'eth0'.
* I can `ping` my jumpbox/server using its real IP#, but cannot `ping 10.8.0.1`
* I can `ssh` to my jumpbox/server using its real IP#, but cannot `ssh 10.8.0.1`
* `nslookup www.whatismyip.com` gives correct results
* browsing to http://www.whatismyip.com/ shows my client's IP# (as also shown in `ifconfig`)
Both my client/laptop and server/jumpbox setups are quite generic OpenVPN-wise, and are almost exactly as described on the Debian wiki
https://wiki.debian.org/openvpn%20for%20server%20and%20client
me@jumpbox:~$ date ; cat /etc/openvpn/server.conf
Sat Nov 8 16:49:00 EST 2014
port 1194
proto udp
dev tun
ca /etc/openvpn/ca.crt
cert /etc/openvpn/server.crt
key /etc/openvpn/server.key
dh /etc/openvpn/dh1024.pem
server 10.8.0.0 255.255.255.0
ifconfig-pool-persist ipp.txt
push "redirect-gateway def1 bypass-dhcp"
push "dhcp-option DNS 8.8.8.8" # google public DNS
keepalive 10 120
comp-lzo
user nobody
group nogroup
persist-key
persist-tun
status openvpn-status.log
verb 3
me@laptop:~$ date ; cat /etc/openvpn/client1.conf
Sat Nov 8 16:51:31 EST 2014
client
dev tun
proto udp
remote ser.ver.IP.num 1194
resolv-retry infinite
nobind
user nobody
group nogroup
persist-key
persist-tun
mute-replay-warnings
ca /etc/openvpn/ca.crt
cert /etc/openvpn/client1.crt
key /etc/openvpn/client1.key
ns-cert-type server
comp-lzo
verb 3
up /etc/openvpn/update-resolv-conf
down /etc/openvpn/update-resolv-conf
My jumpbox/server firewall is currently set to forward everything, using `iptables -t nat -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j MASQUERADE`:
me@jumpbox:~$ date ; sudo iptables -L
Sat Nov 8 16:42:06 EST 2014
Chain INPUT (policy ACCEPT)
target prot opt source destination
fail2ban-ssh tcp -- anywhere anywhere multiport dports ssh
Chain FORWARD (policy ACCEPT)
target prot opt source destination
Chain OUTPUT (policy ACCEPT)
target prot opt source destination
Chain fail2ban-ssh (1 references)
target prot opt source destination
RETURN all -- anywhere anywhere
After I start `openvpn` on first the server and then the client, I see no OpenVPN errors on either the server or the client:
me@jumpbox:~$ sudo openvpn --script-security 2 --config /etc/openvpn/server.conf &
Sat Nov 8 17:48:25 2014 OpenVPN 2.2.1 x86_64-linux-gnu [SSL] [LZO2] [EPOLL] [PKCS11] [eurephia] [MH] [PF_INET6] [IPv6 payload 20110424-2 (2.2RC2)] built on Jun 18 2013
Sat Nov 8 17:48:25 2014 NOTE: the current --script-security setting may allow this configuration to call user-defined scripts
Sat Nov 8 17:48:25 2014 Diffie-Hellman initialized with 1024 bit key
Sat Nov 8 17:48:25 2014 TLS-Auth MTU parms [ L:1542 D:138 EF:38 EB:0 ET:0 EL:0 ]
Sat Nov 8 17:48:25 2014 Socket Buffers: R=[212992->131072] S=[212992->131072]
Sat Nov 8 17:48:25 2014 ROUTE default_gateway=ser.ver.gate.way
Sat Nov 8 17:48:25 2014 TUN/TAP device tun0 opened
Sat Nov 8 17:48:25 2014 TUN/TAP TX queue length set to 100
Sat Nov 8 17:48:25 2014 do_ifconfig, tt->ipv6=0, tt->did_ifconfig_ipv6_setup=0
Sat Nov 8 17:48:25 2014 /sbin/ifconfig tun0 10.8.0.1 pointopoint 10.8.0.2 mtu 1500
Sat Nov 8 17:48:25 2014 /sbin/route add -net 10.8.0.0 netmask 255.255.255.0 gw 10.8.0.2
Sat Nov 8 17:48:25 2014 Data Channel MTU parms [ L:1542 D:1450 EF:42 EB:135 ET:0 EL:0 AF:3/1 ]
Sat Nov 8 17:48:25 2014 GID set to nogroup
Sat Nov 8 17:48:25 2014 UID set to nobody
Sat Nov 8 17:48:25 2014 UDPv4 link local (bound): [undef]
Sat Nov 8 17:48:25 2014 UDPv4 link remote: [undef]
Sat Nov 8 17:48:25 2014 MULTI: multi_init called, r=256 v=256
Sat Nov 8 17:48:25 2014 IFCONFIG POOL: base=10.8.0.4 size=62, ipv6=0
Sat Nov 8 17:48:25 2014 ifconfig_pool_read(), in='TomRoche,10.8.0.4', TODO: IPv6
Sat Nov 8 17:48:25 2014 succeeded -> ifconfig_pool_set()
Sat Nov 8 17:48:25 2014 IFCONFIG POOL LIST
Sat Nov 8 17:48:25 2014 TomRoche,10.8.0.4
Sat Nov 8 17:48:25 2014 Initialization Sequence Completed
me@laptop:~$ sudo openvpn --script-security 2 --config /etc/openvpn/client1.conf &
Sat Nov 8 17:49:12 2014 NOTE: the current --script-security setting may allow this configuration to call user-defined scripts
Sat Nov 8 17:49:12 2014 Socket Buffers: R=[212992->131072] S=[212992->131072]
Sat Nov 8 17:49:12 2014 NOTE: UID/GID downgrade will be delayed because of --client, --pull, or --up-delay
Sat Nov 8 17:49:12 2014 UDPv4 link local: [undef]
Sat Nov 8 17:49:12 2014 UDPv4 link remote: [AF_INET]jump.box.IP.num:1194
Sat Nov 8 17:49:12 2014 TLS: Initial packet from [AF_INET]jump.box.IP.num:1194, sid=25df7af6 0ece4089
Sat Nov 8 17:49:13 2014 VERIFY OK: depth=1, <my config data/>
Sat Nov 8 17:49:13 2014 VERIFY OK: nsCertType=SERVER
Sat Nov 8 17:49:13 2014 VERIFY OK: depth=0, <my config data/>
Sat Nov 8 17:49:14 2014 Data Channel Encrypt: Cipher 'BF-CBC' initialized with 128 bit key
Sat Nov 8 17:49:14 2014 Data Channel Encrypt: Using 160 bit message hash 'SHA1' for HMAC authentication
Sat Nov 8 17:49:14 2014 Data Channel Decrypt: Cipher 'BF-CBC' initialized with 128 bit key
Sat Nov 8 17:49:14 2014 Data Channel Decrypt: Using 160 bit message hash 'SHA1' for HMAC authentication
Sat Nov 8 17:49:14 2014 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 1024 bit RSA
Sat Nov 8 17:49:14 2014 [TomRoche] Peer Connection Initiated with [AF_INET]jump.box.IP.num:1194
Sat Nov 8 17:49:16 2014 SENT CONTROL [TomRoche]: 'PUSH_REQUEST' (status=1)
Sat Nov 8 17:49:16 2014 PUSH: Received control message: 'PUSH_REPLY,redirect-gateway def1 bypass-dhcp,dhcp-option DNS 8.8.8.8,route 10.8.0.1,topology net30,ping 10,ping-restart 120,ifconfig 10.8.0.6 10.8.0.5'
Sat Nov 8 17:49:16 2014 OPTIONS IMPORT: timers and/or timeouts modified
Sat Nov 8 17:49:16 2014 OPTIONS IMPORT: --ifconfig/up options modified
Sat Nov 8 17:49:16 2014 OPTIONS IMPORT: route options modified
Sat Nov 8 17:49:16 2014 OPTIONS IMPORT: --ip-win32 and/or --dhcp-option options modified
Sat Nov 8 17:49:16 2014 ROUTE_GATEWAY lap.top.gate.way/255.255.255.0 IFACE=eth0 HWADDR=la:pt:op:MAC:ad:dr
Sat Nov 8 17:49:16 2014 TUN/TAP device tun0 opened
Sat Nov 8 17:49:16 2014 TUN/TAP TX queue length set to 100
Sat Nov 8 17:49:16 2014 do_ifconfig, tt->ipv6=0, tt->did_ifconfig_ipv6_setup=0
Sat Nov 8 17:49:16 2014 /sbin/ip link set dev tun0 up mtu 1500
Sat Nov 8 17:49:16 2014 /sbin/ip addr add dev tun0 local 10.8.0.6 peer 10.8.0.5
Sat Nov 8 17:49:16 2014 /etc/openvpn/update-resolv-conf tun0 1500 1542 10.8.0.6 10.8.0.5 init
dhcp-option DNS 8.8.8.8
Sat Nov 8 17:49:16 2014 /sbin/ip route add lap.top.IP.num/32 via lap.top.gate.way
Sat Nov 8 17:49:16 2014 /sbin/ip route add 0.0.0.0/1 via 10.8.0.5
Sat Nov 8 17:49:16 2014 /sbin/ip route add 128.0.0.0/1 via 10.8.0.5
Sat Nov 8 17:49:16 2014 /sbin/ip route add 10.8.0.1/32 via 10.8.0.5
Sat Nov 8 17:49:16 2014 GID set to nogroup
Sat Nov 8 17:49:16 2014 UID set to nobody
Sat Nov 8 17:49:16 2014 Initialization Sequence Completed
I then see the following on my client:
* `ifconfig` shows a new entry=`tun0`, which looks correct
* I can `ping` the server using either its real IP# or `10.8.0.1`
* I can `ssh` to the server using either its real IP# or `10.8.0.1`
* `nslookup www.whatismyip.com` gives correct results
... but I get no connection if I open a new instance of Firefox and browse to http://www.whatismyip.com/ :-( "Looking up www.whatismyip.com..." succeeds quickly but the status line continues to display "Connecting to www.whatismyip.com..." until the attempt times out. I also get the same behavior (connection timeout) if I open a new instance of Chrome, or if I browse to http://www.whatismyip.com/ with a Firefox opened prior to starting OpenVPN. FWIW I get the same behavior browsing to any URI, including (e.g.) Google.
This is a major problem for me! For the SSL VPN to work, I need to start a Firefox and run it (since the SSL VPN's vendor only supports it on Linux via a Firefox plugin) to access a particular remote-access website. Furthermore I need the SSL VPN to run through the jumpbox/OpenVPN. (Don't ask, it's a long, sad story ...)
Is there something I must do to configure Firefox to use the VPN? Or is there some other way to fix this?
Alternatively, what should I do to further debug the problem? It just seems odd to me that the other services work (e.g., `nslookup`, `ssh`) but Firefox does not. That being said, both Firefox and Chrome fail in this usecase, so the problem might be generic to web browsers.
your assistance is appreciated, Tom Roche <[email protected]>

You're kidding. You have to go through that rigamarole just to put your bookmarks on your own server? Where's the simple FTP option?
Also, the above-linked article has a broken link. The link to the weaveserver (which is what you have to set up on your own server) is no good, and there is no obvious replacement. There are plenty of Weave-related repositories here:
http://hg.mozilla.org/labs
but it's not clear what you need.

How to configure SFTP Adapter in XI?

Hi All,
How to configure SFTP adapter in XI?, It would be great if anyone sends a step-by-step documentation on the same.
Thanks in advance

Hi,
About SFTP .
1) SFTP (Secure File Transfer Protocol)
"SSH File Transfer Protocol" or SFTP is a network protocol that provides file transfer and manipulation functionality over any reliable data stream. It is typically used with the SSH-2 protocol to provide secure file transfer. SFTP encrypts the session, preventing the casual detection of username, password or anything that is being transmitted. One key benefit to SFTP is its ability to handle multiple secure file transfers over a single encrypted pipe. By using a single encrypted pipe, there are fewer holes in the corporate firewall.
SFTP:
As per the latest SAP PI/XI support pack, it does not support SFTP via File Adapter.
So alternative approach to cater this requirement from XI is to make use of Unix Script at OS level to transfer the files from/to third-party systems.
Inbound Interface - i.e. third-party system ->XI->SAP:
File is transferred to a folder in SAP XI landscape from the third-party legacy system using UNIX Script with secured protocol. Once the file is ready in the XI landscape, File Adapter will poll this directory and file is picked up by NFS protocol.
Outbound Interface i.e. SAP->XI->third-party system:
XI is responsible for writing a file into a folder in the XI landscape. These files are transferred to the third-party system by executing UNIX scripts with secured protocol i.e. via sFTP.
Pre-Requisites:
Public key should be exchanged between external systems and the PI system.
UNIX shell script has to be developed and scheduled.
Advantages:
Highly Secured.
Ability to handle multiple secure file transfers over a single encrypted pipe .By using a single encrypted pipe, there are fewer holes in the corporate firewall.
Disadvantages:
Two-Step process i.e. XI>Temporary folder>External System and vice-versa
Files have to be temporarily stored in XI server.
Multiple failure points i.e. XI and Unix script execution
Maintenance of an external UNIX script.
Difficulty in monitoring the execution of the shell script as it cannot be monitored thru XI.
Need to generate keys and install it in the SFTP site as a pre-requisite i.e. SFTP clients must install keys on the server.
SFTP uses keys rather than certificates. This means that it can't take advantage of the "chains of trust" paradigm facilitated through Certificate Authorities.
Files from the XI server should be deleted/archived in a periodic manner to increase the disc space so that it will increase the performance.
Note: UNIX shell Script can be executed as a background job or' can be triggered from SAP XI through OS command at File adapter level.
Check the links.
Secure FTP (SSH) with the FTP Adapter
Secured File Transfer using SAP XI
Secure FTP in SAP XI
Regards,
Phani
Reward points if Helpful

WAAS Configuration for 3750 Switch

I am configuring a 3750 switch with 12.2(52)SE according to:
(from https://www.cisco.com/en/US/docs/switches/lan/catalyst3750/software/release/12.2_52_se/configuration/guide/3750_scg.pdf )
This example shows how to configure SVIs and how to enable the web cache service with a multicast group list. VLAN 299 is created and configured with an IP address of 175.20.20.10. Gigabit Ethernet port 1 is connected through the Internet to the web server and is configured as an access port in VLAN 299. VLAN 300 is created and configured with an IP address of 172.20.10.30. Gigabit Ethernet port 2 is connected to the application engine and is configured as an access port in VLAN 300. VLAN 301 is created and configured with an IP address of 175.20.30.50. Fast Ethernet ports 3 to 6, which are connected to the clients, are configured as access ports in VLAN 301. The switch redirects packets received from the client interfaces to the application engine.
Note Only permit ACL entries are being used in the redirect-list; deny entries are unsupported.
Switch# configure terminal
Switch(config)# ip wccp web-cache 80 group-list 15
Switch(config)# access-list 15 permit host 171.69.198.102
Switch(config)# access-list 15 permit host 171.69.198.104
Switch(config)# access-list 15 permit host 171.69.198.106
Switch(config)# vlan 299 WEB SERVER
Switch(config-vlan)# exit
Switch(config)# interface vlan 299
Switch(config-if)# ip address 175.20.20.10 255.255.255.0
Switch(config-if)# exit
Switch(config)# interface gigabitethernet1/0/1
Switch(config-if)# switchport mode access
Switch(config-if)# switchport access vlan 299
Switch(config)# vlan 300 WAE
Switch(config-vlan)# exit
Switch(config)# interface vlan 300
Switch(config-if)# ip address 171.69.198.100 255.255.255.0
Switch(config-if)# exit
Switch(config)# interface gigabitethernet1/0/2
Switch(config-if)# switchport mode access
Switch(config-if)# switchport access vlan 300
Switch(config-if)# exit
Switch(config)# vlan 301 CLIENTS
Switch(config-vlan)# exit
Switch(config)# interface vlan 301
Switch(config-if)# ip address 175.20.30.20 255.255.255.0
Switch(config-if)# ip wccp web-cache redirect in
Switch(config-if)# exit
Switch(config)# interface gigabitethernet1/0/3 - 6
Switch(config-if-range)# switchport mode access
Switch(config-if-range)# switchport access vlan 301
Switch(config-if-range)# exit
===================================================================
Question: How do I configure my WAE to play nicely with this switch?

Hi James,
Here is the link to WCCP config part on WAE:
http://www.cisco.com/en/US/docs/app_ntwk_services/waas/waas/v441/configuration/guide/traffic.html#wp1041742
In your case, if my understanding is right, VLAN300 is where you want to connect WAE and WAE is also L2 adjacent. if that is true, here is the config you need on WAE:
wccp router-list 1 171.69.198.100
wccp tcp-promiscuous router-list-num 1 l2-redirect mask-assign l2-return
wccp version 2
Please note that 3750 supports L2 redirection only with redirect IN statements on 3750 interfaces connected to servers and clients.
Hope this helps.
Regards.

How to configure trunk promiscuous?

Hi Guys.
how to configure trunk promiscuous?; i have and access switch connected to a core switch and them to a third party Firewall by an trunk interfaces. I need to have a promiscuous to CORE?; The trunk port to the firewall needs to be a trunk promiscuous?
Thank you.

Hi,
The only way I see is to dedicate a standalone port both on the 6500 switch and on the firewall for the Private VLAN, and configure the corresponding port on the switch as a promisc port (not a promisc trunk - just a promisc port without any tagging). Neither 3750-X nor 6500 support promisc trunk ports so this is not an option for you.
Best regards,
Peter

IAS 10.1.2-how to configure different oc4j listen to different virtualhost?

Hi
I have requirement,
we have oracle portal based web site that can be used by outside users over the internet.
And then we have are deploying few new apps/webservices/ear files on a oc4j called core_ws. These web services should not be accessed outside.
I have created a virtaul host in apache on a different port(7799) which was not exposed to public world.
But, how to configure core_ws to inform Apache to listen on only port 7799 but not on port 80?
I tried a diffent route to attack the problem(as mentioned below) which managmenet did not like:
created location directive, worked in dev but not in production as there ISA sitting front of apache.
We could apply filter on the URLs of these web services in ISA but my director did not like the idea as each time there is additional web service we have mess with it.
So, he prefers running these web services on a different port that will not have access to public.
Appreciate your help if have acheived the same earlier.

By your description, it sounds like you want to do what is in this My Oracle Support document:
How To Create Virtual Host Specific OC4J Applications (Doc ID 389819.1)
https://support.oracle.com/CSP/main/article?cmd=show&type=NOT&id=389819.1
(requires login)
You said you were using 10.1.2, so that will work, its a method of creating separate virtualhosts and using rewrites to direct to error pages if an incorrect request is made. For 10.1.3, but there is a dynamic method which is a better approach.
...Ken

How to configure sync with my local ftp server?

I have used XMarks since now because it hallow me to synchronize my bookmarks with my local server. Now XMarks don't work anymore because it's not more possible to synchronize the passwords.
Any other alternative imposes to use an external server and I don't want to use an external server. My data must remain on my machine it's absolutely excluded that i use an external unknown server for this.
The only solution must be a free solution (a real free solution) and the firefox synchronization seems to me the best/only one.
But I've not found how to configure it to use my own server.
So how to do it, where are the options to the synchronizer to give my own ftp server or whatever other server it needs?

iAS 6.0 sp4 officially does only support iPlanet Directory Server 5.0 sp1 and 4.13.
For more details visit: http://docs.iplanet.com/docs/manuals/ias/60/sp4/ig/prep.htm#42084
I guess, you can specify the directory server during the time of installation.
Thanks,
Rakesh.

How to configure cat 3750 to support ssh2

Similar Messages

Maybe you are looking for