How to configure message retries?
I would like know how to configure automatic message retries.
Below is the scenario,
I have a flow that accepts XML files using File Adaptor. This File adaptor is connected to a DB adaptor. As soon as I feed File Adaptor with an XML file, it will be inserted into a database table. At some point if the database server is busy, it may not accept this incoming call. I want DB adaptor to retry these messages automatically n number of times. Where do I set this retry value?
Thanks,
-vena
Hi.
You can try the following:
1 - If using BPEL:
In the dbadapter partner link configuration, go to the property tab, and add the properties retryMaxCount and retryInterval. They will appear in your bpel.xml file
2 - If using ESB, your routing service must call the DBAdapter synchronously.
Then, in the ESB cosole, under tab Properties for the DBAdapter, add RetryCount and RetryInterval from the list.
Similar Messages
-
How to configure message archieving in PI 7.1 / 7.11 ?
Hi,
I would like to configure message archieving in PI 7.11. Please advise on the any document / help that explain the step.
Thank You and Best Regards
Fernand LesmanaThe following guide explaing the step-by step procedure-
http://www.sdn.sap.com/irj/scn/index?rid=/library/uuid/402fae48-0601-0010-3088-85c46a236f50&overridelayout=true
Also, the following links/notes might be usefull-
http://www.sdn.sap.com/irj/scn/weblogs;jsessionid=(J2EE3417200)ID1506029250DB00994126813914143097End?blog=/pub/wlg/12811
Note 836092 - Archiving/deleting work items in the XI
Note 872388 - Troubleshooting Archiving and Deletion in XI 3.0 / PI 7.0
I think there is no difference in archival setup procedure with PI7.1 and its same as it is in PI7.0 -
How to configure Message bridge
Hi,
I am trying to setup a JMS Message Bridge for prove of concept purpose in Weblogic
7.0. Here is my configurations from config.xml:
<JMSBridgeDestination
AdapterJNDIName="eis.jms.WLSConnectionFactoryJNDIXA"
ConnectionFactoryJNDIName="weblogic.jms.testConnectionFactory"
ConnectionURL="t3://localhost:7001"
DestinationJNDIName="examples.queue2" Name="LocalBridge"
UserName="kyang" UserPassword="{3DES}2LeceOSYOaRuCvrFshnBZg=="/>
ConnectionFactoryJNDIName="weblogic.jms.ClientConnectionFactory"
ConnectionURL="t3://localhost:7001"
DestinationJNDIName="examples.queue1"
Name="MQWeblogicDestination" UserName="kyang"/>
<JMSConnectionFactory DefaultDeliveryMode="Persistent"
DefaultTimeToDeliver="200" DefaultTimeToLive="1000"
JNDIName="weblogic.jms.ClientConnectionFactory"
LoadBalancingEnabled="false" MessagesMaximum="100"
Name="ClientConnectionFactory" OverrunPolicy="KeepNew"
ServerAffinityEnabled="false" Targets="examplesServer"/>
<JMSConnectionFactory DefaultDeliveryMode="Non-Persistent"
DefaultTimeToDeliver="200" DefaultTimeToLive="1000"
FlowControlEnabled="false"
JNDIName="weblogic.jms.testConnectionFactory"
Name="testConnectionFactory" OverrunPolicy="KeepNew" Targets="examplesServer"/>
<MessagingBridge Name="MyMessaging Bridge" Selector="*"
SourceDestination="LocalBridge"
TargetDestination="MQWeblogicDestination" Targets="examplesServer"/>
I used a test client get InitialContext with url:"t3://localhost:7001" and send
the message to "examples.queue2" which is "MyJMSQueue".
From the monitor screen I found the message was put on "MyJMSQueue" but the message
was nerver delieveried to the "examples.queue1".
From the log, I got following message:
<Jun 20, 2002 10:05:53 AM CDT> <Info> <MessagingBridge> <200012> <Bridge "MyMess
aging Bridge" suceesfully found the two adapters configured for it.>
Do you have any suggestions?
Thanks a lot!
Don't worry about the log messages about
"comp/env/wls-connector-resref".
It is not a problem for the Messaging Bridge feature.
The real problem is that you have an invalid selector for the
MessagingBridge. A bridge selector has the same syntax as a JMS message
selector. As you can see from the JMS specification, a message selector
syntax is based on a subset of the SQL92 conditional expression syntax.
I would suggest you try the bridge feature without any selection first
and add the selector later.
Dongbo
Kenny Yang wrote:
>
> Mr.Xiao,
> Thanks! Things are getting better after I made changes according to your suggestion.
> Now the status is showing: Forwarding Messages. But I still have following exceptions
> from the logging window:
>
> <Jun 20, 2002 1:38:50 PM CDT> <Info> <MessagingBridge> <200020> <Bridge "MyMessa
> ging Bridge" is stopped.>
> <Jun 20, 2002 1:38:55 PM CDT> <Info> <MessagingBridge> <200033> <Bridge "MyMessa
> ging Bridge" is getting the connections to the two adapters.>
> <Jun 20, 2002 1:38:55 PM CDT> <Info> <Connector> <190011> <Unable to locate cont
> ext: java:/comp/env/wls-connector-resref>
> <Jun 20, 2002 1:38:55 PM CDT> <Info> <Connector> <190010> <Unable to determine R
> esource Principal for Container Managed Security Context.>
> <Jun 20, 2002 1:38:55 PM CDT> <Info> <Connector> <190011> <Unable to locate cont
> ext: java:/comp/env/wls-connector-resref>
> <Jun 20, 2002 1:38:55 PM CDT> <Info> <Connector> <190010> <Unable to determine R
> esource Principal for Container Managed Security Context.>
> <Jun 20, 2002 1:38:55 PM CDT> <Info> <Connector> <190035> <There was/were 1 phys
> ical connection(s) created with the following Meta Data: Product name of EIS ins
> tance: Java Messaging Service Product version of EIS instance: 1.0.2 Maximum num
> ber of connections supported from different processes: 0 User name for connectio
> n: kyang>
> <Jun 20, 2002 1:38:55 PM CDT> <Info> <Connector> <190011> <Unable to locate cont
> ext: java:/comp/env/wls-connector-resref>
> <Jun 20, 2002 1:38:55 PM CDT> <Info> <Connector> <190010> <Unable to determine R
> esource Principal for Container Managed Security Context.>
> <Jun 20, 2002 1:38:55 PM CDT> <Info> <MessagingBridge> <200031> <Bridge "MyMessa
> ging Bridge" is configured to allow degradation of its quality of service in cas
> es where the configured quality of service is not reachable.>
> <Jun 20, 2002 1:38:55 PM CDT> <Info> <MessagingBridge> <200030> <Bridge "MyMessa
> ging Bridge" is configured to work in "Atmost-once" mode and it is actually work
> ing in "Atmost_once" mode.>
> <Jun 20, 2002 1:38:55 PM CDT> <Info> <MessagingBridge> <200028> <Bridge "MyMessa
> ging Bridge" starts transferring messages.>
> <Jun 20, 2002 1:38:55 PM CDT> <Info> <MessagingBridge> <200026> <Bridge "MyMessa
> ging Bridge" encountered some problems to one of its adapters or underlying syst
> ems. It stopped transferring messages and will try to reconnect to the adapters
> shortly. (Exception caught was java.lang.reflect.UndeclaredThrowableException)
> java.lang.reflect.UndeclaredThrowableException: java.lang.reflect.InvocationTarg
> etException: javax.resource.ResourceException: Error creating asynchronous consu
> mer or setting message lisenter
> at weblogic.jms.adapter.JMSBaseConnection.throwResourceException(JMSBase
> Connection.java:1086)
> at weblogic.jms.adapter.JMSBaseConnection.setMessageListenerInternal(JMS
> BaseConnection.java:984)
> at weblogic.jms.adapter.JMSBaseConnection.setMessageListener(JMSBaseConn
> ection.java:892)
> at weblogic.jms.adapter.JMSConnectionHandle.setMessageListener(JMSConnec
> tionHandle.java:121)
> at java.lang.reflect.Method.invoke(Native Method)
> at weblogic.connector.common.internal.ConnectionWrapper.invoke(Connectio
> nWrapper.java:92)
> at $Proxy131.setMessageListener(Unknown Source)
> at weblogic.jms.bridge.internal.MessagingBridge.beginForwarding(Messagin
> gBridge.java:842)
> at weblogic.jms.bridge.internal.MessagingBridge.execute(MessagingBridge.
> java:922)
> at weblogic.kernel.ExecuteThread.execute(ExecuteThread.java:152)
> at weblogic.kernel.ExecuteThread.run(ExecuteThread.java:133)
> >
>
> where can I get the context:"comp/env/wls-connector-resref"?
-
How to configure Messaging so that it disconnects ...
I've installed Nokia Messaging and configured my e-mail account. Even though I think I set it up properly it just WILL NOT disconnect from my wifi access point - even when the app is turned off and I manually close the internet connection it just keeps on reconnecting. I need an application I can use to check my email once or twice a week, not something that drains the hell out of my (already **bleep**) battery... Is there anything I can do, or should I replace Nokia Messaging with sth else (what?)?
Solved!
Go to Solution.On X6 no matter what I do, I can't make it stay disconnected from the wifi or gprs. It was working well at e71, e72 ... so it is because of this latest version of NM ? Anyhow, if it's not working like before, its useless for me. Just as native email client is, if scrolling doesn't work. That is enough for me, by by NokLa
-
How to configure message header in receiver http adapter?
Hi all
I need the outgoing message payload from receiver http adapter to backend system with below form.
POST http://222.222.33.22 /HTTP1.0
content-type:application/x-www-form-urlencoded
USERID=xxxxxx&PASSWORD=xxxx&SRCID=10&CDDATE=20070601...........................................................................
×POST http://222.222.33.22 /HTTP1.0
○content-type:application/x-www-form-urlencoded
○USERID=xxxxxx&PASSWORD=xxxx&SRCID=10&CDDATE=20070601...........................................................................
Is there a parameter to enable POST method as a part of message header outputing?
thanks in advance.The parameters available in HTTP adapter for message header are:
HeaderFieldFive http://sap.com/xi/XI/System/HTTP
HeaderFieldFour http://sap.com/xi/XI/System/HTTP
HeaderFieldOne http://sap.com/xi/XI/System/HTTP
HeaderFieldSix http://sap.com/xi/XI/System/HTTP
HeaderFieldThree http://sap.com/xi/XI/System/HTTP
HeaderFieldTwo http://sap.com/xi/XI/System/HTTP
HTTPDest http://sap.com/xi/XI/System/HTTP
TargetURL http://sap.com/xi/XI/System/HTTP
URLParamFive http://sap.com/xi/XI/System/HTTP
URLParamFour http://sap.com/xi/XI/System/HTTP
URLParamOne http://sap.com/xi/XI/System/HTTP
URLParamSix http://sap.com/xi/XI/System/HTTP
URLParamThree http://sap.com/xi/XI/System/HTTP
URLParamTwo http://sap.com/xi/XI/System/HTTP -
How to configure an Alert message if communicationChannel(JMS) stops
All,
Is there a way how to configure an alert when the communication channel stops.
<b>Scenario:</b>
In the path Runtime workbench->Component Monitoring->Adapter Engine->Communication Channel monitoring, if we see that a communication channel has stopped(RED traffic light as Status), then can we trigger an alert notification for same.
Currently we have alrerts configured for any message/s failure in the JMS Adapter Framework. So can we trigger simmilar alerts when a comm channel stops(for whatever reason).
Thanks in advance
RKHi Sreeram,
Thanks for the quick reply.
We have a scenario where we activate individual channels at a given time. So in this case, Adapter will always be in RED as all queues are never running in our scenario.
So we need an ALERT to be triggered for individual comm channels. Is theer any way that you can think of ?
Thanks and regards
RK -
How to configure Broadcast messaging for IC Webclient profile
Dear all,
How to configure Broadcast messaging for IC Webclient profile. what are the prerequisites for it?
We are not using EP interface for IC Webclient, then where can I find broadcast messaging URL in SAP CRM system.
I have checked for the relevant BSP application, but could not find.
Please help me to configure the scenario successfully, your help will be highly appreciated.
Best regards,
Raghu ramHi raghu
In CRM Broad cast messaging application is CRM _BM,
Go to easy access u2013 go to favourites u2013 select add other objects - select BSP Applications- then select CRM_BM Application.
Select that BSP application and test it u2026
`
Regards,
Narsimha -
How toremove messages from JMS Queue?how to configure queue in spring?
Hi
I have Confiured a JMS configaration in spring applicationConfiguaration.xml file
<bean id="connectionFactory" class="org.apache.activemq.ActiveMQConnectionFactory">
<property name="brokerURL" value="tcp://localhost:61616"/>
<property name="useAsyncSend" value="true"/>
</bean>
<bean id="queue" class="org.apache.activemq.command.ActiveMQQueue">
<constructor-arg value="foo"/>
</bean>
<bean id="broker" class="org.apache.activemq.xbean.BrokerFactoryBean">
<property name="config" value="classpath:activemq.xml" />
<property name="start" value="true" />
<!-- <property name="messageListener" ref="auditInterface"/> -->
</bean>
<bean id="auditInterface"
class="org.springframework.jms.remoting.JmsInvokerProxyFactoryBean">
<property name="serviceInterface" value="com.infiniti.gpn.auditing.AuditInterface"/>
<property name="connectionFactory" ref="connectionFactory"/>
<property name="queue" ref="queue"/>
</bean>
<bean id="listenerContainer" class="org.springframework.jms.listener.SimpleMessageListenerContainer">
<property name="connectionFactory" ref="connectionFactory"/>
<property name="destination" ref="queue"/>
<property name="messageListener" ref="auditMessageListener"/>
</bean>
Sender is sedning messages continusly messages that messages r storing in queue , these r acupying more memory in RAM , due to that jboss is restarting for each request, is there any way to clean up messages in Queue ? if it is there then how will configure that queue in apllicationConfiguaration.xml file?
Thanks in advance
NaraI suggest posting your question on the [Spring Remoting and JMX forum|http://forum.springframework.org/forumdisplay.php?f=30].
-
How to remove messages from JMS Queue?how to configure queue in spring?
Hi
I have Confiured a JMS configaration in spring applicationConfiguaration.xml file
<bean id="connectionFactory" class="org.apache.activemq.ActiveMQConnectionFactory">
<property name="brokerURL" value="tcp://localhost:61616"/>
<property name="useAsyncSend" value="true"/>
</bean>
<bean id="queue" class="org.apache.activemq.command.ActiveMQQueue">
<constructor-arg value="foo"/>
</bean>
<bean id="broker" class="org.apache.activemq.xbean.BrokerFactoryBean">
<property name="config" value="classpath:activemq.xml" />
<property name="start" value="true" />
<!-- <property name="messageListener" ref="auditInterface"/> -->
</bean>
<bean id="auditInterface"
class="org.springframework.jms.remoting.JmsInvokerProxyFactoryBean">
<property name="serviceInterface" value="com.infiniti.gpn.auditing.AuditInterface"/>
<property name="connectionFactory" ref="connectionFactory"/>
<property name="queue" ref="queue"/>
</bean>
<bean id="listenerContainer" class="org.springframework.jms.listener.SimpleMessageListenerContainer">
<property name="connectionFactory" ref="connectionFactory"/>
<property name="destination" ref="queue"/>
<property name="messageListener" ref="auditMessageListener"/>
</bean>
Sender is sedning messages continusly messages that messages r storing in queue , these r acupying more memory in RAM , due to that jboss is restarting for each request, is there any way to clean up messages in Queue ? if it is there then how will configure that queue in apllicationConfiguaration.xml file?
Thanks in advance
NaraHi,
Even i have a similar kind of requirement where in, i want to clear the JMS Queue Message programmatically, on certain condition.
i am using Spring JMS. The JMS Queue has a listener. In the listener we want to clear the Queue contents based upon the condition.
If anybody has any idea about this, please reply back.
Thanks in Advance.
Manjunath. -
How to configure Symantec Mail Security for SMTP & Messaging Server 6.3
Hi!
I want to install a Symantec Mail Security for SMTP 5.0.1(host1) with Messaging Server 6.3 (in production - host2), but when I try to access to POP protocol to send a message from Internet, the system display a message with a relay problem.
- Could you help me with this issue?,
- Do you know some documentation that speaks of this?. I can't find any documentation that explain how to configure and integrate SMS and Messaging Server. Thanks in advance.
Regards, CRctemp1 wrote:
I want to install a Symantec Mail Security for SMTP 5.0.1(host1) with Messaging Server 6.3 (in production - host2), but when I try to access to POP protocol to send a message from Internet, the system display a message with a relay problem.I take it that you have configured the symantec software like this?
internet -> symantec mail security system -> sun messaging server -> recipientA better approach is the following
internet -> sun messaging server -> recipient
|
V
symantec mail security system(refer here: http://blogs.sun.com/factotum/entry/messaging_server_correctly_deploying_the)
- Do you know some documentation that speaks of this?. I can't find any documentation that explain how to configure and integrate SMS and Messaging Server. Thanks in advance.There is no documentation specifically for symantec software but we do document how to send emails via the symantec mail security server using the aliasdetourhost channel keyword:
http://docs.sun.com/app/docs/doc/819-4428/6n6j42615?a=view#bgaqy
Regards,
Shane. -
How to configure the file adaptor so as to send an sample XML message.
Hi all ,
I had done the configuration and now i want to test the scenario but i dont now how to do that ?.
how to configure the file adaptor so as to send an sample XML message to the integration server ?.
I am totally new to XI.
please help me out how to do it.
its an urgent.
Thanks,
shujaHi,
I think you should post your question Process Integration (PI) & SOA Middleware.
Regards
Message was edited by:
Shehryar Khan -
Hi,
I have an EAR file thai includes an EJB 3.0 module with a MDB. I use a Queue.
This is my code,
@Resource(mappedName = "jms/NotificationQueue")
private Queue notificationQueue;
@Resource(mappedName = "jms/NotificationQueueFactory")
private ConnectionFactory notificationQueueFactory;
public Customer update(Customer customer){
Customer updated = em.merge(customer);
try {
sendJMSMessageToNotificationQueue(updated);
} catch (JMSException ex) {
Logger.getLogger(CustomerSessionBean.class.getName()).log(Level.SEVERE, null, ex);
System.out.println("Customer updated in CustomerSessionBean!");
return updated;
private Message createJMSMessageForjmsNotificationQueue(Session session, Object messageData) throws JMSException
//Modified to use ObjectMessage instead
ObjectMessage tm = session.createObjectMessage();
tm.setObject((Serializable) messageData);
return tm;
private void sendJMSMessageToNotificationQueue(Object messageData) throws JMSException
Connection connection = null;
Session session = null;
try
connection = notificationQueueFactory.createConnection();
session = connection.createSession(false, Session.AUTO_ACKNOWLEDGE);
MessageProducer messageProducer = session.createProducer(notificationQueue);
messageProducer.send(createJMSMessageForjmsNotificationQueue(session, messageData));
finally
if (session != null)
try
session.close();
catch (JMSException e)
Logger.getLogger(this.getClass().getName()).log(Level.WARNING, "Cannot close session", e);
if (connection != null)
connection.close();
layed inside a stateless EJB 3.0.
And the MDB looks as follow,
@MessageDriven(mappedName = "jms/NotificationQueue", activationConfig = {
@ActivationConfigProperty(propertyName = "acknowledgeMode", propertyValue = "Auto-acknowledge"),
@ActivationConfigProperty(propertyName = "destinationType", propertyValue = "javax.jms.Queue")
public class NotificationBean implements MessageListener {
public NotificationBean() {
public void onMessage(Message message)
try
Object msgObj = ((ObjectMessage)message).getObject();
if (msgObj != null)
Customer customer = (Customer)msgObj;
System.out.println("Customer with the following details has been updated:");
StringBuilder sb = new StringBuilder();
sb.append("Customer ID=");
sb.append(customer.getCustomerId());
sb.append(", ");
sb.append("Name=");
sb.append(customer.getName());
sb.append(", ");
sb.append("Email=");
sb.append(customer.getEmail());
System.out.println(sb.toString());
catch (JMSException ex)
Logger.getLogger(NotificationBean.class.getName()).log(Level.SEVERE, null, ex);
I have configured both "jms/NotificationQueue" and "jms/NotificationQueueFactory" inside OC4J server.
But when I try to deploy the EAR file, the server gives me the following error,
Operation failed with error: No destination location set for message-driven bean NotificationBean
How must I do to let the EAR file be deployed?
Thanks in advance
JoseMingzhuang
I want to configure a error queue for weblogic jms topic. Wanted: The message goes to error destination when messages have expired or reached their redelivery limit.
1. using jms transport configure proxy service:
Retry Count :3
Retry Interval:10
Error Destination: ErrorTopic
Expiration olicy: RedirectUnlike File/SFTP, JMS proxy service definition does not have the concept of Error Destination. To accomplish similar functionality go to JMSQ on (for which proxy is configured) server console (http://localhost:7001/console) and configure the Error Destination. Following URL will help in how to configure JMS Q.
http://edocs.bea.com/wls/docs103/ConsoleHelp/taskhelp/jms_modules/queues/ConfigureQueues.html
http://edocs.bea.com/wls/docs103/ConsoleHelp/taskhelp/jms_modules/queues/ConfigureQueueDeliveryFailure.html
I tried use the proxy service to consume message from the jms topic . and generation an error in the proxy message flow. But the message didn't goes into the error topic.If every thing is configured as per above step, then the after retries, the weblogic server will put the message into JMS topic configured. Your proxy will receive from this topic.
Let me know if we are not on same page.
Cheers
Manoj -
How to configure a error queue for weblogic jms topic
Hi guys.
I want to configure a error queue for weblogic jms topic. Wanted: The message goes to error destination when messages have expired or reached their redelivery limit.
1. using jms transport configure proxy service:
Retry Count :3
Retry Interval:10
Error Destination: ErrorTopic
Expiration Policy: Redirect
I tried use the proxy service to consume message from the jms topic . and generation an error in the proxy message flow. But the message didn't goes into the error topic.
Any suggestions for this topic? Can anyone provide some helps or any useful links.
Thanks in advance.
MingzhuangMingzhuang
I want to configure a error queue for weblogic jms topic. Wanted: The message goes to error destination when messages have expired or reached their redelivery limit.
1. using jms transport configure proxy service:
Retry Count :3
Retry Interval:10
Error Destination: ErrorTopic
Expiration olicy: RedirectUnlike File/SFTP, JMS proxy service definition does not have the concept of Error Destination. To accomplish similar functionality go to JMSQ on (for which proxy is configured) server console (http://localhost:7001/console) and configure the Error Destination. Following URL will help in how to configure JMS Q.
http://edocs.bea.com/wls/docs103/ConsoleHelp/taskhelp/jms_modules/queues/ConfigureQueues.html
http://edocs.bea.com/wls/docs103/ConsoleHelp/taskhelp/jms_modules/queues/ConfigureQueueDeliveryFailure.html
I tried use the proxy service to consume message from the jms topic . and generation an error in the proxy message flow. But the message didn't goes into the error topic.If every thing is configured as per above step, then the after retries, the weblogic server will put the message into JMS topic configured. Your proxy will receive from this topic.
Let me know if we are not on same page.
Cheers
Manoj -
How to configure the web interface of service desk
Hi All,
We are currently doing a configuration on solman service desk. I am on a stage where in i need to use the web interface of service desk via tcode notif_create_bsp. However, every time i call the transaction code (call the url) i cant view the web. Only an error the "Network Access Message: The website cannot be found".
I already activate needed services and already publish
SIAC_PUBLISH_ALL_INT but it still doesnt work.
I might have missed some configs/procedure on how to do it correctly.
My questions are.
1. How am i going to know the qualified domain name
of the Web AS for solman? How to configure it?
2. Can anyone give me some guide and any step by step documentation/procedure on this.
You help/suggestion will be very much appreciated
Thank you very much,
IceHi,
+"Check the following 2 things. See if the port 8000 is open and in the url for the BSP in internet explorer, replace the host name with the IP address of your Solman server.+
+"+
That was a helpful tip. I change the host name with the ip address ofour solman server. However, upon login, it promts me to enter username and password. I've tried to login using my solman password but it shows an error like this.
Business Server Page (BSP) error
What happened?
Calling the BSP page was terminated due to an error.
SAP Note
The following error text was processed in the system:
Die URL enthält keine vollständige Domainangabe (10.123.161.125 statt 10.123.161.125.).
Exception Class CX_FQDN
Error Name
Program CX_FQDN=======================CP
Include CX_FQDN=======================CM002
ABAP Class CX_FQDN
Method CHECK
Line 10
Long text -
Error type: Exception
Your SAP Business Server Pages Team
Is there anything i need to configure so that i can maintan the username and password?
Thank you for your assistance,
Ice -
How to configure ACS 5.2 for policy condition on TACACS+ Service
In https://supportforums.cisco.com/message/3953175#3953175 thread, I was able to get the ACS 5.2 work with SRX for both SSH CLI and J-Web TACACS+ accounts. However, I found the behavior is different on our production environment. I found our ACS 5.2 was configured authorization rule with condition "TACACS+ Service" = "junos-exec". I don't know how to configure this on my ACS 5.2 Please guide me how to configure this.
I found there was NO TACACS+ "Authorization Request" when access via J-Web in our production SRX and ACS. However, there were TACACS+ "Authorzation Request" when access via J-Web in our production SRX and ACS. The difference between my lab ACS and production ACS is the authorization rule condition. In my condition, I configure with all "SRX" Device Type. but in our production ACS 5.2, it was configure to TACACS+ Service=junos-exec. so I like to test it in our lab to find out the difference. Thanks.I would suggest you to go through the below two link.
http://www.cisco.com/en/US/docs/net_mgmt/cisco_secure_access_control_system/5.2/migration/guide/Migration_Configure.html
http://www.cisco.com/en/US/docs/net_mgmt/cisco_secure_access_control_system/5.2/user/guide/common_scenarios.html
Maybe you are looking for
-
MIGO values when invoices/credit memos have already been posted
Hi everyone, We are facing an issue with the values the system is calculating when doing the GR (and/or GR reversals) once invoices/credit memos have already been posted regarding the PO (Non Stock POs = non valuated). When a goods receipt is posted
-
Design complex business mapping & business validation
There is a task to develop complex mapping. For example it is needed to perform several DB Query in order to map CODE from one application to ID in another application. Each rule depends on previous result. I see several approaches: 1) To design comp
-
In 2012 I used bootcamp to get windows 7 on my macbook pro 8.1, running Lion. I was able to resize the partition at any time, over the last year windows 7 has become less needed and frankly it's a sucky OS anyway even compared to XP so I'm happy to r
-
Send Internal table to mail with Colman name
Hi, how can i send the content of internal table to mail , i try to convert to HTML and send it but the problem is that i don't get the column name , there is another way to send the IT with the column name ? any e.g will help i am stuck .... Regards
-
My iPhone is disable due to too many wrong password entries. I have some important things that I would not like to loose. Will the disable mode restore to normal after a period of time or do I really have no option but to restore it via iTunes theref