How to??? External Disk to AEBS (Space-looking one (g))
I would greatly appreciate if somebody could tell me whether it is possible to connect a G-drive external storage device to the USB port on my alien-looking AEBS. I know that with the new AEBS's it is possible, but I am not sure "if and how" on my 2yr old station.
I connected it but it is not appearing anywere on my computer.
In case it matters: My AEBS is connected by WAN Ethernet to the DSL modem. I use WEP-128 for security.
Thanks in advance
Sorry, only the new 802.11n AirPort Extreme Base Station's (AEBSn) USB port will support multiple external USB hard drives. Neither the AirPort Express (AX) or earlier 802.11g (flying saucer) AirPort Extreme (AEBS) base station support hard drives.
Similar Messages
-
How much external disk space is needed for editing HD video?
If I'm using FCE:
1) How much external disk space is needed for editing HD video:
if I downloaded 150mins of HD video? and
do editing with it which will have an output of 120mins.
Now PC, going to a MAC user soon Windows XPHi(bonjour)!
As a rule of thumb for HDV editing, use those numbers:
12 to 15 meg/second for capturing ( your project is 150 minutes long, so 780 meg/minute, or 117 to 125 Gig).
If you do any editing, add transition, video effect, add 12 to 15 meg /second to the total.
As your project will have to be rendered for the print to tape operation, calculate 12 to 15 meg/second for all the length of your final movie. Add this amount to the total. (example: a 60 minutes movie : 49 Gig).
If you want to burn a DVD on your Mac, calculate 3 to 4 meg/second for downconversion to DV material if you check "self-contained" in quicktime export dialog. (example: your finished project is 60 minutes long : 10.8 Gig)
iDVD itself needs 3 to 4 times this amount if you want flawless operation.
Finally, if you use your internal hard disk for all this storage (it's not a good idea to capture on the same drive where Mac OS X belongs), your Mac OS needs some spare room to breath (doing caching, etc), and your hard drive must have a least 25% of free space to avoid file's fragmentation.
As hard drive's price drop, get the maximum size you can afford. 250 Gig is a good choice if you want to do just one project of 90 to 150 minutes at the time.
Michel Boissonneault -
How increase external disk size used for an existing file system, Solaris10
Configuration:
Server: Sun T5220
S/O: Solaris 10 5/08 s10s_u5wos_10 SPARC
Storage: EMC AX4-5
EMC PowerPath: PowerPath Version 5.2
I have the following scenario:
In AX4-5 storage array, I created two LUNs into RAID Group 10, with Raid Type1/0:
LUN 101: 20Gb
LUN 102: 10Gb
Both LUNs were added to Storage Group (SG1) that includes two Servers (Server1 and Server2); both servers have Operating System Solaris 10 5/8 and Power Path.
The servers detect both LUNs across two paths. With Power Path were created a virtual path (emcpower0a, emcpower1a) to access to each LUNs respectively.
We have mounted two file system /home/tes1 over emcpower0a -> LUN101 and /home/tes2 over emcpower1a -> LUN102.
Filesystem size used avail capacity Mounted on
/dev/dsk/emcpower0a 20G 919M 19G 5% /home/test1
/dev/dsk/emcpower1a 10G 9G 1G 90% /home/test2
I want to increase the space in file system /home/test2, without lost the information that I have stored and using the same LUN, LUN 102. To do this I start with the following steps:
1- Create new LUN, LUN 103 with 15Gb into RAID Group 10. Result: OK, I have available space in RAID Group 10.
2- Add LUN 103 to LUN 102, using concatenation option. Result: OK. This action creates a new metaLUN with the same characteristics of LUN 102, but with new space of 25Gb.
After to do these actions, I want to know how Solaris recognize this new space. What I need to do, to increase the size of file system /home/test2 to 25 Gb. Is that possible?
I reviewed the description of each disk using format command, and the disks not have any change.
Could anyone help me? If you need more detail, please do not hesitate to contact me.
Thanks in advance.Robert, thank a lot for your know how. You helped me to clarify some doubts. To complete your answer, I will add two more details, based on my experience.
After to execute, type -> auto configure and label, the disk was created with different partitions like root, swap, usr, like this:
Volume name = < >
ascii name = <DGC-RAID10-0223 cyl 49150 alt 2 hd 32 sec 12>
pcyl = 49152
ncyl = 49150
acyl = 2
nhead = 32
nsect = 12
Part Tag Flag Cylinders Size Blocks
0 root wm 0 - 682 128.06MB (683/0/0) 262272
1 swap wu 683 - 1365 128.06MB (683/0/0) 262272
2 backup wu 0 - 49149 9.00GB (49150/0/0) 18873600
3 unassigned wm 0 0 (0/0/0) 0
4 unassigned wm 0 0 (0/0/0) 0
5 unassigned wm 0 0 (0/0/0) 0
6 usr wm 1366 - 49149 8.75GB (47784/0/0) 18349056
7 unassigned wm 0 0 (0/0/0) 0
This was not convenient because all information stored appear in the first slice and growfs not work if appear root or swap slice into the disk, for that reason was necesary to recreate manually every slice with partition command. The final result was this:
Part Tag Flag Cylinders Size Blocks
0 unassigned wm 0 - 49149 9.00GB (49150/0/0) 18873600
1 unassigned wu 0 0 (0/0/0) 0
2 backup wu 0 - 49149 9.00GB (49150/0/0) 18873600
3 unassigned wm 0 0 (0/0/0) 0
4 unassigned wm 0 0 (0/0/0) 0
5 unassigned wm 0 0 (0/0/0) 0
6 unassigned wm 0 0 (0/0/0) 0
7 unassigned wm 0 0 (0/0/0) 0
Now, execute again the label command to save the new information.
Mount file system and execute:
growfs M file_system mount_point to expand the file system to 9Gb. -
How to password-protected an external disk on yosemite?
I search for hours but with no results...
I'm searching for a simple and free application that will password protect my external disk I'm moving from one place to another one. There are a lot of free solutions for PC but I have a hard time finding a solution for Mac.
Encryption with disk utility is not a solution for me since my 10.6.8 computer would not recognize the disk.
Moreover, I only want a simple password-protection.
I bought a WD elements and thought I could use Wd security but it looks like it only works with WD my passport (that contains this software) and that WD is preventing WD elements hard disks to be recognized by this application....
I searched the internet and it looks like there is no free solution. Or any free solution is not updated (not yosemite compatible).
Is there a free app ? Or do I have to buy a software (in that case which one would you recommend me)?
Thanks for your advices.Thank you Kappy but you didn't read all my post. I quote "Encryption with disk utility is not a solution for me since my 10.6.8 computer would not recognize the disk."
-
Can i put iphoto library on external disk?
i'd like put my iphoto source library on an external disk to keep space free on my startup disk. i can do this in itunes pretty easily. having trouble finding a way to do it in i photo. is it possible? (i'm not talking about backing up, but putting the primary library on an external drive).
Mark
1. Quit iPhoto
2. Copy the iPhoto Library Folder as an entity from your Pictures Folder to the External Disk.
3. Hold down the option (or alt) key while launching iPhoto. From the resulting menu select 'Choose Library' and navigate to the new location. From that point on this will be the default location of your library.
4. Test the library and when you're sure all is well, trash the one on your internal HD to free up space.
Regards
TD -
Yosemite cannot mount external disks
Since I upgraded to Yosemite my IMAC does not mount external disks, even the bright new one I bought
I have also a Macbook Air that I upgraded to Yosemite and these same external disks can be mounted on the Macbook Air.
I have searched on the Apple support community and on the internet and quite some people whom upgraded to Yosemite have the same problem.
I checked the USB specs on both the IMAC and the MACbook Air
IMAC :
Hostcontroller : builtin userinterface
OS hostcontroller : AppleUSBEHCI
PCI- code : 0x3b34
PCI revision code : 0x0006
PCI factory code : 0x8086
Busnb : 0Xfd
MACBook Air:
Hostcontroller : builtin userinterface
OS hostcontroller : AppleUSBEHCI
PCI- code : 0x0d9d
PCI revision code: 0x00a2
PCI factory code : 0x10de
Bus Nb : 0x24
Needless to say that I need the data stored on the external disks.
Thks for helping me out.I have read that if you turn Spotlight off you will have no problems. Open Spotlight, choose "privacy", click the "+" at the lower left and add what you do not Spotlight to search. Worked for me. I have 2 internal Seagates formatted OS X journaled in an external case.
-
I have several itunes libraries after moving them and losing them, and recreating new ones. How do I get them all back together? I have a Macboook Pro OSX 10.6. My newest library is currently being directed to an external drive. I have files that I moved around improperly and don't know where they all go now. I'm pretty good with it all if someone can explain. Nothing I've read explains how to find your lost libraries on an external drive and put them into one place.
If you have it on an external drive and do not have the space on the hard drive can you still do the library/organize/consolidate feature and have files available without the external drive attatched? I just don't know how I will get all the files into itunes without taking up a bunch of space.
Thank you so much!I'm confused as to why you would need or even want multiple iTunes libraries... but that's not really relevant.
It certainly is possible to have the iTunes library reside entirely on an external drive.
The organize/consolidate feature will work with an external drive but the drive must be connected. How would you expect this to work without the drive connected? iTunes cannot magically move files to consolodate them on a drive that's not connected.
I"m not really certain what you mean by "get them all back together". iTunes libraries are not "together". If you've got multiple libraries they are seperate...there is simply no other way to make that happen.
Realistically, if this hasn't helped, it's going to be up to you to explain why you have/need multiple iTunes libaries so that we can offer specific details on how to resolve the issue and possibly a better solution. -
I would like to stotre several movies on an external disk drive connected to Airport express through USB port. With my IPAD, I am able to use the WiFi network (generated by Airport) buy I don't see the disk.... how to make it happen ? Thanks. JP A
Shoudl I use ICloud instead or another way ?
I have not tried iCloud for this...and understand that it is mainly for your backups. These link might help:
http://www.apple.com/icloud/get-started/
http://www.apple.com/icloud/setup/
Or, you could post in the iPad support area since that is really what your question is about. -
Hi,
I am moving all the videos I have in my iphoto library on my computer to the imovie library (version 9.0.9 ) I have on an external disk to free some space on the internal disk.
Afterwards, I am deleting them from the iphoto library BUT I noticed that the free space on the internal disk does not increase. Movies are decreasing but the space is going to back ups. I am doing this process as I want to have more space on the internal disk. Do I do something wrong or is this the normal process ?
Also, I have Imovie (new version - which I am not using, at least not for the moment) and the old version (created when I updated) on my internal disk and a copy I made befor the update on an external disk.
Is it safe to delete the old version on the internal disk ?
Thanks for helping me out !Hi,
On my mac I have iphoto and two versions of imovie - application that was created last october (2.9 gb -- so far I did not use this app) and 9.0.9 imovie folder (1,197,747,040 bytes - 1.22 GB on disk) .
On the external disk, I made a copy of 9.0.9 version some while ago (to be eaxct, before the new version was installed last october).
This what I do:
- import the video into imovie on my internet disk via "file, import, photos, iphoto library and select..."
- then I delete the videos from the iphoto event, emtpy trash in iphoto and empty trash on my dock
I photo version I am using is 9.5.
What do you mean with your third question ?
I back up on a 2nd external disk (used only for back up) with time machine.
When I check the space available (on this mac, more info, storage...) I noticed backups take up 7,6 GB. Before I started the above mentioned process of importing videos in imovie on the external disk the backups showed 0. What did I do wrong ?
Thanks for helping me out.
Brigitte -
My MacBook Pro won't go beyond a white screen, after I pushed the restart button. How can I get it to a login? I have routinely backed it up, but don't know how to bring that up, nor if I have a boot file on that external disk. Help!
Take each of these steps that you haven't already tried. Stop when the problem is resolved.
To restart an unresponsive computer, press and hold the power button for a few seconds until the power shuts off, then release, wait a few more seconds, and press it again briefly.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If a desktop Mac hangs at a plain gray screen with a movable cursor, the keyboard may not be recognized. Press and hold the button on the side of an Apple wireless keyboard to make it discoverable. If need be, replace or recharge the batteries. If you're using a USB keyboard connected to a hub, connect it to a built-in port.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider. -
I want to set up the Time Machine and I would love to use the Time
Capsule but since I already have a wireless router I need suggestions on
what other
external disks Apple could recommend to use with the Time Machine and
how to configure that disk.
A complication that I need to resolve is the fact that I am using Vmware
Fusion to be able to use Windows on my Mac. Now it seems that Time
Machine is not backing up my files
on that virtual Windows without additional configuration and my question
is whether you can advise me here or whether this is only a matter for
the Fusion virtual machine.If you want to use Time Capsule you can.. you simply bridge it and plug it into the existing router.. wireless can be either turned off or used to reinforce the existing wireless.. eg use 5ghz in the TC which is much faster than your 2.4ghz.
You can also use a NAS.. many brands available but the top brands are synology, qnap and netgear readynas series. These will all do Time Machine backups although how well always depends on Apple sticking to a standard. There are cheaper ones.. I bought a single disk zyxel which was rebadged and sold through my local supermarket. It actually works very well for TM at least on Snow Leopard. Major changes were made in Lion and again ML so do not instantly think it will work on later versions. I haven't tried it yet with those versions.
Any external drive can be plugged into the mac. Use the one with the fastest connection or cheapest price according to your budget. USB2 drives are cheap and plentiful. But no where near as fast as USB3 or FW800. So just pick whichever suits the ports on your Mac. Interesting Apple finally moved to USB3 on their latest computers.
TM should exclude the VM partition file.. it is useless backing it up from Mac OS side.. and will slow TM as it needs to backup that partition everyday for no purpose.. TM cannot see the files inside it to backup just the changes.
You need to backup windows from windows. Use MSbackup to external drive.. if you have pro or ultimate versions you can backup to network drive. But MSbackup is a dog.. at least until the latest version it cannot restore the partition without first loading windows. There are about a zillion backup software versions for windows.. look up reviews and buy one which works for you. I use a free one Macrium Reflect which does full disk backups and is easy to restore.. to do incremental backups though you have to pay for it. -
I have three iphoto_libraries stored in a external disk PASSPORT (one for each trip imovie Im making -Ive managed this way the libraries so to not confuse the trips) while the actual files are in OTHER external disk LACIE. And everything was fine: imovie find each library, could work with it, or iphoto could edit the files.
But one day everything crashed at the same time: i opened iphoto to find 3 different scenarios:
1) iphoto_library GREECE was there, but not the albums i prepared. no events. when double click in any of them: "Volume not found"
2) iphoto_library ITALY was there, and the albums i prepared too, but empty.
in both cases I can only see the photos in 'photos' because 'events' shows some events with photo preview and some with no preview, just some kind of preset clipart palm tree, but if i enter the event, photos are there but again: when double click in any item: "Volume not found"
3) iphoto_library ISRAEL was there, the albums too, when double click in any of them: all OK
The 3 libraries was managed the same way. Meaning: Ive imported photos to iphoto from external disk LACIE in a iphotolibrary stored in another external disk PASSPORT. Also: I don't have unchecked the option "copy to file" or something like that. photos where moved, not copied. Also i have all the movie_libraries in the PASSPORT as well. What happened??
Solution? Nothing yet. Ive moved now all the photo folders from LACIE together in PASSPORT with the iphotolibraries but problem persist:
HOW CAN I TELL THE LIBRARIES WHERE TO LOOK FOR THE VOLUMES NOW?
"Volumes" are the original files aren't them?
Please help. this is so annoying to try and find in the forum, to tricky to explain
I have a Macbook pro retina Yosemite 10.10.1 / iphoto 9.6 (910-29)/ iMovie 10.0.6
THANK YOU
VickyThe 3 libraries was managed the same way. Meaning: Ive imported photos to iphoto from external disk LACIE in a iphotolibrary stored in another external disk PASSPORT.
This is not clear, especially when you say
I don't have unchecked the option "copy to file" or something like that. photos where moved, not copied.
Especially as the message you're getting is typical of a library where the ' option "copy to file" or something like that' is unchecked.
So it's a simple question:
Are you these Managed or Referenced Libraries?
A Managed Library, is the default setting, and iPhoto copies files into the iPhoto Library when Importing. The files are then stored in the Library package
A Referenced Library is when iPhoto is NOT copying the files into the iPhoto Library when importing because you made a change at iPhoto -> Preferences -> Advanced. (You unchecked the option to copy files into the Library on import) The files are then stored where ever you put them and not in the Library package. In this scenario you are responsible for the File Management. -
How do I clone an external disk using CCC?
I have a MacBook Air and because it has only 256 GB and I need about three times that space for storing movies, document files etc., I use an external hard disk to keep these files on.
I formatted this disk using Mac Extended Journal but I did not put the Snow Leopard Operating System on it. I just move files from the computer's hard drive to the disk as required.
I had a scare once where the data on another external hard disk was wiped out because of a faulty USB cord. All the movies were lost and I could not recover the data. The disk also failed to mount. This problem kept happening several times. When I got rid of the faulty USB cord, the external disk mounted and I never lost data again. I am certain all the problems were due to the faulty USB cord. I have been using the same external disk ever since and it has been working fine with the non-faulty USB cord so I am sure it didn't have anything to do with the disk and it was the USB cord that was the problem. I used the same faulty USB cord with other external disks and the same problems arose - failure to mount etc.
This is the background for why I want to make a copy of this external drive. I don't want to lose the movies and other data on this disk if something goes wrong again and want everything on another disk just in case.
I usually use Carbon Copy Cloner to make backups. But that is with a external disk that has OS 10.6.8 on it.
I really don't want to put OS 10.6.8 on the external drive where I store movies and other over-spill data on it.
How do I go about making a copy of this external disk using CCC (or using another program if CCC won't work for this)?
I have two USB ports on my MBA. I prefer to use CCC over SuperDuper because I had a problem with SuperDuper in the past.So as I understand it, CCC will clone any disk to any disk so long as it's formatted to Mac (extended Journal) and I don't have to put the Mac operating system on the disks that I am copying from and copying to?
Thanks for answering. -
How to monitor DFS shares disk usage/free space?
How to monitor DFS shares disk usage/free space?
Using Netapp filer shares to which DFS points. Looking for powershell script to send report.Hi,
How about using Disk Quota function in FSRM (File Server Resource Manager)?
Please see:
Quota Management
http://technet.microsoft.com/en-us/library/cc755917(v=ws.10).aspx
In your case you can setup a soft quota with a specific size so that when it runs out of space you set, you will get an email or warning according to your setup.
If you have any feedback on our support, please send to [email protected] -
How-to: desperate need of help in partitioning an external disk drive
Some time ago, after installing PARALLELS, my external disk drive lost one of the two HFS+ partitions it had (465 GB total, 50% one and 50% the other).
Now, after having sent it to assistance, the technicians have recovered all possible data, with one issue: they have created a NTFS partition with all recovered data.
The external disk drive is now as shown on:
http://www.tyrexionibus.com/pictures/partition-diskutility.png
** WHAT'S THE MATTER ? **
I want to save the data contained in the first partition and partition the disk with two HFS+ partitions (60% and 40% of the disk space, particularly). In other words, I need to CONVERT (from NTFS to HFS+) and RESIZE (from 50% to 60%) the first partition and MAKE (40% of disk space) another HFS+ partition WITHOUT losing data.
Please note that I _DO NOT_ have sufficient disk space in my MacBook Pro's HDD to move all data from the external disk drive to it, create a new partition and then move all data to the new partition again.
How can I solve this issue?I don't read Italian, but from the screen shot it appears that the first partition is not formated as NTFS. Am I missing something?
The safest thing to do would be to use a second external drive to back up everything while you are changing formats and partitions. I guess you create a new partition on half the disc, more all the data to the new partition, then modify the first partition; but that seems risky.
Maybe you are looking for
-
I've been checking all around to find a source to this problem and it seems to continue leading back to where the problem may be with Apple's time zone referencing software. Some time zone maps incorrectly place all the Aleutian Islands in the Aleut
-
Inspection plan as per customer sale order
Hi QM Expert, I want to create Inspection plan automatically when inspection lot is created against production order which is made by reference of sales order which contain the specifications of product required by customer every time the customer ch
-
How can I make a short cut to my gmail in toolbar
Since upgrading to Firefox 5 my short cut icons to google and gmail have disappeared. How can I reinstate them?
-
Accessing Address from ADRC table
Hi, When inputting a delivery address in a PR the three options are to search by customer, vendor, or input an address. My questions is how do you access inputted addresses? These inputted addresses are saved in the ADRC table, but when creating a
-
I tried to register my macbook air 2013 and it said the serial number was already registered
I tried to register my macbook air 2013 and it said the serial number was already registered. I purchased it in my city at an authorized reseller beucase there isn't any Apple Store and they told me that they haven't registered it. How can I solved