How to modify capabilities for the ethernet interfaces in a Solaris 10 x86

Hello.
Does anybody know how to configure the ethernet capabilities in a interface in a X86 server? I have read that NDD command is not supported for this kind of servers and I cannot find how to do that.
My root problem is that the IPMP is not working and my first clue is the configuration for cap_pause parameter in the involved interfaces, that they are active for both IPMP interfaces.
How can I modify cap_pause for the interfaces in this server: X4170 with Solaris 10.
Thanks in advance
Regards,
Luis.

Not familiar with the X4170 but you might want to look for a config file in /kernel/drv that matches your interface. There are some configuration parameters you can set there if the device driver supports the .conf file.

Similar Messages

How to change the Ethernet Interface name in Solaris 10

I have to install Oracle 10G RAC on three nodes with different ethernet cards, but the ethernet interface name must be the same which is the precondition for Oracle RAC installation.
So I want to know how can I change the ethernet name in Solaris.
For example, the ethernet name in the OS is "ce0", how can i change the interface name "ce0" to "e1000g0".
bash-3.00# dladm show-dev
ce0 link: unknown speed: 1000 Mbps duplex: full
ce1 link: unknown speed: 100 Mbps duplex: half
ce2 link: unknown speed: 100 Mbps duplex: half
ce3 link: unknown speed: 100 Mbps duplex: half
ce4 link: unknown speed: 100 Mbps duplex: half
ce5 link: unknown speed: 0 Mbps duplex: unknown
Thanks in advance.

s-wilson wrote:
You can't. The ce or e1000g refers to the driver as well as the adapter itself. The only exception I am aware of is: the ipge and e1000g which both refer to the Intel Pro 1000.I'm pretty sure I've renamed a driver in the past (and all references to it in name_to_major, path_to_inst, driver_aliases, and minor_perm) and had it function just fine after 'plumb'ing it up. However I just tested this by trying to turn a 'pcn' driver into a 'foobar' driver on a vmware box. It looks like everything works except some internal bits of the driver continue to create one file with 'pcn' in the name instead of 'foobar'. And since this is Solaris 10, the /devices filesystem is dynamic and read-only. I can't seem to force the change.
So while this may be possible with some drivers (and maybe only on older versions of the OS), it doesn't seem to be generally possible for all drivers on Solaris 10.
Darren

How to modify formula for the calculated measure in a cube.

Hi,
I need to modify formula for some measures within a cube, What would be the best way do that? In the obj view if I update the formula and compile, it does seem to reflect in the model view.
I cannot delete and recreate the measures deletion and recreation would change the order of the measures which i do not need.
Appreciate your inputs. thanks

Yes thats true it desnt change in the AWM front end if you change the formula in object view but it would show you results according to the new formula.
If you want AWM to show the correct expression in the front end then the way out is to change in the XML and reimport the xml.
Thanks,
Brijesh
Edited by: Brijesh Gaur on Nov 18, 2009 5:51 PM

How do I set up the port interface for the WAN side of my RVS4000 to 100T Full Duplex?

How do I set up the port interface for the WAN side of my RVS4000? The ISP says I need to set it to 100T Full Duplex, but where would I do that? In the Router's administration GUI I can't find any options to make such settings for the WAN side.

The setup of the folders in Finder is entirely up to you. Whatever suits your needs is what you should do. Lightroom will be fine no matter how you set it up.
So I'm not really sure what your question is.

How can I find my Mac Adress for the Ethernet Port from a Apple Airport Express Device ?

How can I find my Mac Adress for the Ethernet Port from a Apple Airport Express Device ?

You can only locate, lock or erase your device when it is logged into iCloud and 'Find My Phone' is enabled, additionally the device will need to be switched on and connected to a wifi or cellular network.
Unfortunately, you cannot activate iCloud or 'Find My Phone' remotely.

CRS-5008: Invalid attribute value: ce0 for the network interface

Hi all,
we try to install grid infrastructure 11GR2 (11.2.0.1) into Solaris Zone with shared network interface.
We also modified scirpt racgvip, so it will be able to login (via ssh with key authorization) to the global zone and add or remove interface on zone. Script itself works fine.
But it seems that orarootagent some how checks the interface, and returned error.
In the log of the orarootagent I can see error:
2010-10-01 21:38:49.573: [ AGFW][9] CHECK initiated by timer for: ora.net1.network sapdr2db2 1
2010-10-01 21:38:50.473: [ora.net1.network][17] [check] NetworkAgent::checkLink returned false
2010-10-01 21:38:50.474: [ora.net1.network][17] [check] NetInterface::sGetIpAddress {
2010-10-01 21:38:50.474: [ora.net1.network][17] [check] netInterfaceName empty.
2010-10-01 21:38:50.474: [ora.net1.network][17] [check] NetInterface::sGetIpAddress }
2010-10-01 21:38:50.474: [ AGFW][17] check for resource: ora.net1.network sapdr2db2 1 completed with status: OFFLINE
2010-10-01 21:38:50.476: [ AGFW][17] Executing command: check for resource: ora.net1.network sapdr2db2 1
2010-10-01 21:38:50.477: [ora.net1.network][17] [check] NetworkAgent::init enter {
2010-10-01 21:38:50.478: [ora.net1.network][17] [check] Checking if ce0 Interface is fine
2010-10-01 21:38:50.479: [ora.net1.network][17] [check] NetInterface::scheckNetInterface returned 0
2010-10-01 21:38:50.480: [ora.net1.network][17] [check] CRS-5008: Invalid attribute value: ce0 for the network interface
2010-10-01 21:38:50.480: [ora.net1.network][17] [check] NetworkAgent::init exit }
2010-10-01 21:38:50.480: [ora.net1.network][17] [check] NetInterface::scheckNetInterface returned 0
2010-10-01 21:38:50.480: [ora.net1.network][17] [check] NetworkAgent::checkInterface returned false
Does anybody know how the orarootagent checks for the network resource?
It seems that there are some procedures (NetworkAgent::checkLink, NetInterface::sGetIpAddress) inside it. But the problem is that this file is binary.
Or may be there are some ways to track how orarootagent checks?

>
2010-10-18 18:11:07.589: [ora.net1.network][9] {0:2:8} [check] Checking if ce0 Interface is fine
2010-10-18 18:11:07.589: [ora.net1.network][9] {0:2:8} [check] NetInterface::scheckNetInterface returned 0
2010-10-18 18:11:07.590: [ AGENT][9] {0:2:8} UserErrorException: Locale is
2010-10-18 18:11:07.591: [ora.net1.network][9] {0:2:8} [check] CRS-5008: Invalid attribute value: ce0 for the network interface
>
Is there anything I can do with it? Will appreciate any help!Is ce0 a valid interface on the machine? (has the global zone done "ifconfig ce0 plumb"?)
Is the zone correctly configured (check output of the export sub-command of zonecfg)?
--Sowmini

How to fetch data for the Change Request in PROCESS_EVENT

Hi All,
I need to write some custom logic on Save/Submit button. For this I am planning to enhance the PROCESS_EVENT method of class CL_USMD_CR_MASTER. Within this method I need to access runtime data of the change request currently being processed.
I am going to create a post-method exit for this PROCESS_EVENT method. Is this correct?
I have heard we have APIs in MDG which can be used to fetch data, however I do not know how to use the same.
Can someone please help me with sample code how to fetch the runtime data of the Change Request
Thanks in advance.
Regards,
Vanessa

What MDG domain are you working on? What you are trying to do is called "reuse mode" enhancement and you do NOT want to tinker with the FPM feeder classes in this case. SCN document Configuration and Enhancement of SAP Master Data Governance contains many examples on how to achieve this.
This is a how-to document for MDG-M reuse mode enhancement: Extend MDG-M Data Model by a New Entity Type (Reuse Option)
This is a how-to document for MDG-C/S reuse mode enhancement: SAP How-To Guide: Extend the MDG Business Partner - Node Extension (Reuse Option)
Keep in mind, these examples are mainly for additional "master data" fields. If you need additional fields that are not master data but are more related to the Change Request itself, you should use this how-to document: Enhancement of the User Interface Building Block for Change Requests
Again, all of these documents can be found on the first document I referenced above. I suggest that you bookmark it.

Where to find the XSLT used for the standard interface in SAP ME 5.2 SP05?

Hallo!
Starting with SAP ME 5.2 SP05 there is a new logic for the standard interface used in SAPMEINT.
I wonder where to find the XSLT's that are used for transforming the XML messages?
I can see from the SAP NW log:
[Transaction: -1] starting execution of Visiprise/ERPShopFloorIntegration/frame/workflow/XSLTDelegate.trx
Loading file Visiprise/WEB/XSLT/Outbound/EquipmentStatusChangeUnSchDown/EquipmentStatusChangeUnSchDownRequest.xslt
select: path Visiprise/WEB/XSLT/Outbound/EquipmentStatusChangeUnSchDown
select: name EquipmentStatusChangeUnSchDownRequest.xslt
The definition for this XSLT is as follows:
WEB://Visiprise/XSLT/Outbound/EquipmentStatusChangeUnSchDown/EquipmentStatusChangeUnSchDownRequest.xslt
How is this resolved???
From the (pre SP05) SAPMEINT I know two variants:
1. High performance interface
The XSLT files come from the MII shared memory entries for project SAPMEINT
2. Standard interface
The XSLT files come from SAP ME (table XSLT and XLST_ASSIGBNMENT) via calling a HTTP URL like
http://<hostname>:<port>/manufacturing/vm/xslt?id=RouterFeed
Kr,
Erich Lind

Hello!
I found the answer myself now.
The XLST files are part of the static web content of the MI project Visiprise.
In the SAP MII workbench go to the project Visiprise
Then under the tab Web the static contecnt can be found under the folder WEB/XSLT/..

Network adapter for the private interface for RAC

Hi guys
This is the specification for the Network adapter for the private interface in RAC:
The network adapter for the private interface must support the user datagram protocol (UDP) using high-speed network adapters and a network switch that supports TCP/IP (Gigabit Ethernet or better).
Do you have a document where I can have more deep details about it ?
Thanks

user2931261 wrote:
This is the specification for the Network adapter for the private interface in RAC:
The network adapter for the private interface must support the user datagram protocol (UDP) using high-speed network adapters and a network switch that supports TCP/IP (Gigabit Ethernet or better).Note that TCP is also used in addition to UDP over the Interconnect. As for the statement that the NIC must support UDP - wrong statement to make. The NIC does not support UDP. The IP (Internet Protocol) stack does. The NIC supports the bottom layer of the ISO model. UDP is at layer 4.
As for your Interconnect, you have two basic choices. Gigabyte Ethernet or Infiniband.
For GigE you need of course a GigE NIC and a GigE switch, and a cable to wire the NIC into the switch.
For Infiniband you need a HCA card (e.g. Mellanox InfiniHost PCI card) and an Infiniband switch. As HCA cards are dual port, it make sense to get 2 cables and wire both ports into the switch and bond those 2 ports as a single logical NIC. You can run IPoIB (IP over Infiniband), which means that the 2 ports on the HCA will be seen by the o/s as NICs - and bonding is supported which enables you to create a single logical NIC on top of these 2 NICs and thus have full redundancy.
Also note that GigE typically is only 1Gb/s. 10 Gb/s is available, but expensive (especially the switch). Infiniband typically is QDR rate today that provides you with 40Gb/s pipes. So each port on the HCA will be 40Gb and the bonded port will thus be 2x40Gb/s.
Infiniband is a lot faster and more scalable for an Interconnect than GigE.
Also, because of the capacity and flexibility and low latency of Infiniband, you can also use it for your storage fabric layer (running your storage protocol over it).
Typically you will need to get HBA cards (dual fibre port) to wire the RAC node to the storage array's fibre channel switch. These HBA ports are 2Gb/s.
You can eliminate these HBAs and fibre cables by using a storage protocol like SRP (Scsi RDMA Protocol - RDMA=Remote Direct Memory Access) - running SRP over your Infiniband infrastructure, together with your Interconnect.
This is btw what Oracle's Database Machine and Exadata Storage servers use (and one the reasons they have broken all RAC performance records).

How to create and see the user interface of helloworld sample??

hello friends,
i have deployed the hello world sample
now i want to know how to create and see the user interface of hello world sample.
thanks and regards..

If you go to bpel console host:port/BPELConsole (in a dev install, localhost:9700), click on your process, we will generate, based on the describing wsdl a UI for you ..
hth clemens

How to modify and save the data in the table control

how to modify and save the data in the table control

hi priya,
kindly go thru the code below.
PROCESS BEFORE OUTPUT.
MODULE status_9010.
LOOP WITH CONTROL tab_control.
    MODULE move_data_to_table.
ENDLOOP.
PROCESS AFTER INPUT.
MODULE user_cancel AT EXIT-COMMAND.
LOOP WITH CONTROL tab_control.
    MODULE move_data_from_table.
ENDLOOP.
MODULE move_data_to_table OUTPUT.
This is to move the data from the internal table to *the table control
*zmpets_mode-modecode, zmpets_range-rangeid, *zmpets_servfacto-factor are field names of the table *control columns.
READ TABLE int_factor INDEX tab_control-current_line.
IF sy-subrc = 0.
    zmpets_mode-modecode = int_factor-modecode.
    zmpets_range-rangeid = int_factor-rangeid.
    zmpets_servfacto-factor = int_factor-factor.
ENDIF.
ENDMODULE.                 " move_data_to_table OUTPUT
**********************************************8888
MODULE move_data_from_table INPUT.
*To move the data from the table control to internal *table 'INT_FACTOR'.
int_factor-chk = line.
int_factor-modecode = zmpets_mode-modecode.
int_factor-rangeid = zmpets_range-rangeid.
int_factor-factor = zmpets_servfacto-factor.
   MODIFY int_factor INDEX tab_control-current_line.
    IF sy-subrc NE 0.
      APPEND int_factor.
      CLEAR int_factor.
    ENDIF.
ENDMODULE.                 " move_data_from_table INPUT
if this helps , kindly award points.
for any clarification just mail me.
regards,
Anversha.S
[email protected]

How to create F4 for the standard transaction

Hi all ,
How to create F4 for the standard transaction for a particular field .
Bye

Santosh,
You can create F4 values for a field in a standard Transaction .
1. First search for a standard search help meeting your requirement .
2. If you don't find one, create your own custom (z) serach help .
( 1 is preferable )
After that, include that serch help to the standard field in the transaction .
For this u need to go to the screen
( F1->F9-> screen-> Field )
Click on the property of the field and include the search help .
You ll require the access key from the basisi guys as u r changing standard .
Hope it helps,
~ laxmi
Reward for helpful answers

How to implement tooltip for the list items for the particular column in sharepoint 2013

Hi,
I had created a list, How to implement tooltip for the list items for the particular column in SharePoint 2013.
Any help will be appreciated

We can use JavaScript or JQuery to show the tooltips. Refer to the following similar thread.
http://social.technet.microsoft.com/forums/en/sharepointdevelopmentprevious/thread/1dac3ae0-c9ce-419d-b6dd-08dd48284324
http://stackoverflow.com/questions/3366515/small-description-window-on-mouse-hover-on-hyperlink
http://spjsblog.com/2012/02/12/list-view-preview-item-on-hover-sharepoint-2010/

How do I test for the presence of an active open document in Photoshop?

I’m new to Adobe scripting, and one of my first scripts deals with the activeDocument in Photoshop.
If there is no activeDocument, I want to display a message and terminate the script. My efforts
so far have been met with frustration. While developing the script in ExtendScript Toolkit,
I used the test expression "activeDocument in app", and everything worked as expected. And when I installed the script
in the Photoshop scripts folder and ran it from Photoshop with a document open, it also worked.
But when I ran the script from Photoshop with no document open, it failed.
Moreover, after that,the script failed when I tried to run it in ESTK.
I did some testing and found that my test expression, "activeDocument in app"
was returning true, even though no document was open.
Still in ESTK, I replaced the “app” with ”Application” in the test expression. That worked when
I stepped through the script. But when I tried to run it without stopping, it stopped at the
test expression, and displayed the error message, “Application is undefined.”
So how do I test for the presence of an open document in Photoshop ??

After posting this, I discovered the Photoshop Scripting Forum, and I found my answer there.—
I should have used “app.Documents.length” as my test expression.

Why does my Airport Express say "self assigned IP address"? No IP address for the ethernet, and it is not connecting to my cable router any longer...

Why does my Airport Express say "self assigned IP address"? No IP address for the ethernet, and it is not connecting to my cable router any longer...

Some cable providers.....like mine, a well known company......seem to take anywhere from a few moments to sometimes up to 30 minutes to allow their equipment back at the cable company to fully reset and issue a new fresh connection.
So, it would not hurt to leave things powered down for 15-20 minutes or more when you perform the reset that John Galt suggests.

How to modify capabilities for the ethernet interfaces in a Solaris 10 x86

Similar Messages

Maybe you are looking for