How to Reconcile Production Planning & Controling Data

Dear Experts,
Currently we are implementing the below Production Planning & and Controlling  cubes.
1. Capacity Load Utilization (0PP_C13)
2. Plan/Actual Comparison Operation/Work Center View (0PP_C03)
We have updated the data in C13 and cube and doing the reconcile with standard reports.
In R/3 which T codes are usefull for C13 and C03 cube data reconciliation.
Regards
Ramu

Dear Suresh,
The View of CRHD_V1 is not giving the available capacity information.
I need to reconcile available & Target capacity  information WITH Plant and work center wise.
BW Query names are 0PP_C13_Q001 & 0PP_C13_Q002
Regards
Ramu

Similar Messages

  • SAP PP (Production Planning) Master Data Definitions

    SAP PP (Production Planning) Master Data Definitions and Transaction codes.

    SAP PP (Production Planning) Master Data Definitions
    • Factory Calendar
    • Material Master
    • Resource • Bills of Material (BOM)
    • Production versions
    • Master recipe
    Factory Calendar: The factory calendar is defined on the basis of a public holiday calendar. The public holiday and factory calendar is a central module in the SAP System. It is assigned to a specific plant during the initial system setup and therefore used in many areas (e.g. in Logistics and in Human Resources) in the system.
    Material Master: Material master comprises if all the basic data of the material for each department. The data covers all the relevant information required for the transactional flow e.g. sales, Planning, Production, Quality, Purchasing, Costing etc. Material master covers all the descriptive and control data and the flow of information depends on fields maintained within it. The integration of all material data in a single database object eliminates redundant data storage. Material Masters are created once and can be changed or extended whenever required
    Bill of Materials: Bill of Materials or commonly called BOM is a formally structured list of components that make up a product or assembly. The list contains the material number of the component together with the quantity and unit of measure. BOMs are used in their different forms in various situations where a finished product is assembled from several component parts or materials. Resources: Resources are production facilities and persons involved in a production process that have capacities. They are subdivided into categories to specify their suitability for certain purposes or their use in certain processes
    Product Versions: A production version determines which alternative BOM is used together with which task list/master recipe to produce a material or create a master production schedule. For one material, we can have several production versions for various validity periods and lot-size ranges. The production version determines the following:
    • The BOM alternative for a BOM explosion.
    • The task list (master recipe) and any alternate, as needed.
    • Lot-size restrictions and validity parameters.
    Master Recipes: A master recipe defines the following data that is required for the production of materials without relating to a particular order: processing steps, resources, material components, and control information for the process control level. Master Recipe enables to plan the production of materials (products). Therefore, Master Recipe is used as a template for process orders and run schedules as well as a basis for product costing. In a Recipe
    • The Phases (work steps) to be carried out during production.
    • The activities to be performed in the operations as a basis for determining dates, capacity requirements and costs.
    • The use of materials during production.
    • The use of resource.

  • How to fetch the Table Control data to Customer Table(Z-Table) ?

    How to fetch the Table Control data to Customer Table(Z-Table) ?

    Hi Krishna,
    Check this sample programs
    http://www.planetsap.com/online_pgm_main_page.htm
    http://sap.niraj.tripod.com/id29.html
    http://www.sapdevelopment.co.uk/dialog/tabcontrol/tc_basic.htm
    Have a look at below links. It will help you.
    http://help.sap.com/saphelp_nw04/helpdata/en/9f/dbac5135c111d1829f0000e829fbfe/content.htm
    http://help.sap.com/saphelp_nw04/helpdata/en/9f/dbac1d35c111d1829f0000e829fbfe/content.htm
    Thanks,
    Reward If helpful.

  • How to run production planning  in APO

    Hi gurus,
    how to run production planning  in APO.
    Can u explain me.
    prasad

    Prasad,
    An unfocused question; a similar answer.  Try online help for a start
    http://help.sap.com/saphelp_scm70/helpdata/en/2a/18dc37c7f2d67ae10000009b38f889/frameset.htm
    Best Regards,
    DB49

  • How to copy the Planned GI date as the pricing date in Invoice

    Hi!!,
    For this requirement we want the price the product based on the Planned GI date and not the actual GI date...For some case when Planned GI date was early and we shipped late.It means we would be creating the Invoice later than the Planned GI date and hence the billing date would be my pricing date in the Invoice which will be the later date....
    We want that the pricing should be as on Planned GI date.....is there a standard way we can accomplish this using configuration?
    Helpful answers would be handsomely rewarded.
    Thanks

    Hi, I had a similiar reqmt but in that case we wanted the Pricing date from the Sales Order to be copied into the Billing Document Pricing Date (for the correct pricing) instead of the Actual GI Date from the Delivery to flow to the same.
    We achieved this using ABAP by making a copy of the Data Transfter routine found in Data VBRK/VBRP field in the copy control and adding the required codes to it. Hope this gives you some lead.

  • Production order control data tab

    Hi,
    Is there any chance the costing data under control data tab in production order can make out "grayed" so that users can not change costing sheet, RA key.
    Thanks in advance.

    Dear Sprint,
    Try with SHD0, make the field as display only
    [http://wiki.sdn.sap.com/wiki/display/Snippets/TransactionVariant-AStepbyStepGuidefor+Creation]
    [http://sapfunctional.com/General/ScreenVariants/Index.htm]
    [http://help.sap.com/saphelp_nw04/helpdata/en/7d/f639fb015111d396480000e82de14a/content.htm]
    If possible take help from technical person
    Regards
    Madhu

  • How to create tables for control data

    HI
    How to create  tables for controls of types of data (screen control)? what is the process for this
    Regards,
    Anil

    Well, do you want to do it the easy way?  If so, then just create a table maintenance program.  You can do this via SE11, utilites, table maintenance generator. The table maintenance will be generated and you can then maintain the table via SM30. 
    If you want to go the more challenging way, you can write your own table maintenance program using a table control on your screen.  You can use the table control wizard to help you along.
    Regards,
    Rich Heilman

  • How to Copy Production/Live Environment Data into Staging Environment?

    I have been given the task to go into the Production/Live Environment within SharePoint and copy the data and place it into the staging environment. I have been told the Staging data is older. 
    I have no idea how to do this. The Staging Environment uses different site collection URLs. I only want to copy the data so links and everything wont take me to the production site. 
    I am a new admin.

    Hi,
    If you just copy a site collection from Production environment to Staging environment, you can backup the site collection in Production then restore in Staging.
    Back up a site collection:
    https://technet.microsoft.com/en-us/library/ee748609(v=office.14).aspx
    Restore a site collection:
    https://technet.microsoft.com/en-us/library/ee748630(v=office.14).aspx
    If the web application only has this site collection or you want to copy the web application, you can deattach the database of the web application in Production then attach it in Staging.
    Or, you can find a third party tool to do it.
    Thanks,
    Wendy
    TechNet Community Support
    Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact
    [email protected]

  • How to implement production planning in thermal power plant-help needed

    water is fed to boiler drum through boiler feed pump and it is taken to boiler drum.
    then water is heated is taken through water tubes and moving towards bottom.the heat produced due to burning of coal surrounds the the water tubes amd the water in water tubes , get converted to steam and that steam is taken to super heaters in 3- stages(platen, radian like stages) and finally it gets super heated at final super heater and it is to turbine through main steam temperature control valve and temp of steam is 510 c and when it reaches turbine it 's temp reduces to 504 c and it first enteres first stage of turbine, it's pressure get reduced at sucessive stage, when it leaves the tubine, steam pressure is only 0.8 kg/cm2 and when in entersrs turbine it's pressure is 88 kg/cm2.
    then it is taken to water cooled condenser and it is cooled and it is taken to cooling towers and finally it is taken to bfp and fresh addition of incoming water takes place.chemical dosing takes place here.finally taken to boiler drum.
    the coal from coal yard after taken from coal through coal conveyors, it reaches the boiler firing elevation through coal pipes located at 14 meters from ground.
    intial firing is done with light diesel oil and after flame stabilization, we will use high density furnace oil. then after that we will go for coal.if there is any fluctuation in stability of flame or reduction of temp of furnace, then hfo oil gun is taken for use.
    the flue gas from furnace , is taken ttrough , air ptr-heater and frsher air from primary air fan and forced draft fan will mix with flue gas in pre-heater and takes the heat of flue gas. so wastage heat is reduced somewhat.
    the heavy ash formed in furnace is taken through downwards and from that to storage of heavy ash by heavy ash conveyor.
    the fly ash is taken through esp(electo static precipitator)by flue gas and finally to fly ash gets seperated from fly ash storage.the exhaust came out from chimney.
    this is the process in power plant.
    turbine vaccum is created by ejector
    regards,

    water is fed to boiler drum through boiler feed pump and it is taken to boiler drum.
    then water is heated is taken through water tubes and moving towards bottom.the heat produced due to burning of coal surrounds the the water tubes amd the water in water tubes , get converted to steam and that steam is taken to super heaters in 3- stages(platen, radian like stages) and finally it gets super heated at final super heater and it is to turbine through main steam temperature control valve and temp of steam is 510 c and when it reaches turbine it 's temp reduces to 504 c and it first enteres first stage of turbine, it's pressure get reduced at sucessive stage, when it leaves the tubine, steam pressure is only 0.8 kg/cm2 and when in entersrs turbine it's pressure is 88 kg/cm2.
    then it is taken to water cooled condenser and it is cooled and it is taken to cooling towers and finally it is taken to bfp and fresh addition of incoming water takes place.chemical dosing takes place here.finally taken to boiler drum.
    the coal from coal yard after taken from coal through coal conveyors, it reaches the boiler firing elevation through coal pipes located at 14 meters from ground.
    intial firing is done with light diesel oil and after flame stabilization, we will use high density furnace oil. then after that we will go for coal.if there is any fluctuation in stability of flame or reduction of temp of furnace, then hfo oil gun is taken for use.
    the flue gas from furnace , is taken ttrough , air ptr-heater and frsher air from primary air fan and forced draft fan will mix with flue gas in pre-heater and takes the heat of flue gas. so wastage heat is reduced somewhat.
    the heavy ash formed in furnace is taken through downwards and from that to storage of heavy ash by heavy ash conveyor.
    the fly ash is taken through esp(electo static precipitator)by flue gas and finally to fly ash gets seperated from fly ash storage.the exhaust came out from chimney.
    this is the process in power plant.
    turbine vaccum is created by ejector
    regards,

  • How to map Product Group for the Materials in BW.

    Hi All,
    We have an requirement for one of the report called as Progress validation Report.
    We have to craete thsi repotr which would pulll out Inventory value, Production Plan value, Total Lates, Current week deliveries and WIP for a quarter.
    Cube whihc provides details about production plan has data by Material, plant and product group wise.
    But rest of the cube from which we extract the key figures does not have data by Product grop wise.
    Product group is been picked from PGMI table in R/3.
    How I can related the materials  which are in other cube to the respective Product group.
    Material and the relevant prdoct group data doesnot flows in BW.
    There is even a scenario where ahve seen a material falls under 2 product groups..
    PLease guide as how i can realted already existing materials in the Cube to the product group.
    Points will be assigned
    Thanks & Regards
    Vaishali Patil

    Hi,
    Product Group is master data for material master. It is part of Matreial Clssification data in R/3.
    Please check if you are having the same already loaded as attribute of Material master. I guess it will be there, if it s not there then you should try to load the same in material master object which you are using in all the cubes.
    If the maintinenece in master data is nopt possible then you got to populate the same in cube.
    There will be a combination of keys (materail/plant/prduct family etc.. ( for which Product group will be unique). then load product with the help of these key combinations in all the cubes via update routine.
    There is one more way to have this but which is performance intensive.
    You may create one master data object called Product Group and keep material number as attribute (with compunding all other key fileds to get the unique combination). Then you may create an infoset using cubes and this master data object. Join the materail numbers in all. Display this object in report.
    I hope it will help.
    Thanks,
    S

  • Determination Idoc Control data - Outbound

    Hi Guru's
    I would like to know how to get the idoc control data, like receiver port and receiver partner. For example:
    I have an ABAP program which collects the IDOC data at the end I want to send out the IDOC, but what is the best way to determine the receiver information? Or how does it work in relation with partner profiles?
    Best regards,
    Guido Koopmann

    You don't need to specify all of the information - your distribution model will take care of it.  Do something like this snippet of code for the control record for output-based processing:
    * Populate the control record
      gs_ctrlout = gs_ctrlin.
      CALL FUNCTION 'OWN_LOGICAL_SYSTEM_GET'
        IMPORTING
          own_logical_system             = lv_logsys
        EXCEPTIONS
          own_logical_system_not_defined = 1
          OTHERS                         = 2.
      IF sy-subrc EQ 0.
        gs_ctrlout-sndprt = 'LS'.
        gs_ctrlout-sndprn = lv_logsys.
      ELSE.
      ENDIF.
      gs_ctrlout-serial(8)   = sy-datum.
      gs_ctrlout-serial+8(6) = sy-uzeit.
    If you have a standalone program, before calling MASTER_IDOC_DISTRIBUTE, you just need to fill the message type and IDOC type in the control record.

  • How to trace planned order data after it has been converted into production

    Hi, There,
    The planned order has been converted into production order.
    However, I need to trace if this planned order is generated by MRP
    run or created manually. I can't get any planned order info from
    table PLAF. Any input?
    Regards,
    Nancy

    Hi,
    Once fully converted, the Planned Order data will not be available in the Table : PLAF.
    If it is available, then You can have the details with the Time Stamp and User data from PLAF.
    But, the refrence will be available in the Production Order.
    You want to make a Track of the Planned Order details and the Quanity, then you need to have/create Z tables so that the data will be availabe.
    This is how most of the Organizations keep a track of the Planned order data.
    Hope this helps..
    Regards,
    Siva

  • How to consider production capacity plan on sales order's delivery date.

    HI experts,
    How to consider production capacity  on sales order's delivery date.
    Say for example :
    Production workcenter capacity to produce the XYZ material 10qty in a Day.
    today i have created the sales order XYZ materail qty of 100. lead days has give based of MMR 21 days 17-07-2010( 3 sundays)
    and in same day i have created other sales order XYZ material qty 5000 ,the lead days again it will came 17-07-2010.
    Now my client requiremnt is when the schedule days is confirming in the sale order it sholud also consider the production capacity planning also
    Even though my work centers are overloaded it is confirming the sales order on 17-07-2010 (based on leads days in MMR)
    Thanks in Advance..
    Sudha

    Sudha,
    Tell your client he needs to install SCM.  Here, you can use either CTP or MLATP to confirm orders based on production capacity.
    There are a couple of standard workarounds available in R/3. 
    One is to create a constrained forecast for planning materials, consistant with capacity, convert the forecast to PIRs, and then perform ATP against 'Planning' rather than against product, using MRP Strategy 63.
    http://help.sap.com/saphelp_erp60_sp/helpdata/en/a2/4e799a927d11d1800f00c04fadcb73/frameset.htm
    Another method is to leave the Sales orders unconfirmed at original order entry (eg, no lead time).  Run MRP, run capacity levelling, firm the levelled planned orders, and then run BOP (called 'rescheduling' in R/3) against the unconfirmed backlog, with an ATP that considers firmed planned orders as supply elements.  The sales orders will confirm against the planned orders, which are scheduled according to available capacity.
    Either of these two methods will work, but the CTP SCM solution is by far the better answer.  Downside of SCM solution in general is the substantial implementation effort required.
    Rgds,
    DB49

  • How to control data

    Hi,
    When 2 SKUs are removed how to control data.
    Regards,
    krishna.

    Hi Krishna,
    The following is the process for controlling data during
    SKU deletions
    1) Once the SKU deletion confirmation is received, the
    corresponding statistical/concensus forecast from DP
    has to be deleted
    2) The CVC's has to be deleted and time series needs to
    be updated
    3) The previous forecast if released to SNP has to be
    deleted using transaction /sapapo/rlcdel
    4) The demand generated in SNP/PPDS generated based
    on previous planning run needs to be deleted
    5) Integration models needs to be blocked for those SKUs
    6) If there are any confirmed/firmed production orders, those
    has to be deleted
    7) Communication to be given to concerned plants not to
    make that product
    Regards
    R. Senthil Mareeswaran.

  • How Production Order finish date and time is being comptued by SAP?

    Hello Expert,
    How Production Order finish date and time is being comptued by SAP? for example, we create a Production Order via CO01, the basic start date is 29.09.2008 and time is 04:00 it gives us basic finish date is 29.09.2008 and time is 13:28.
    how does SAP compute the time 13:28 as it finished time
    Please explain me briefly.
    Thanks
    Ryan

    Hello Guys,
    When we create Production Order in R/3 the time is calculated by routing but it is extended at SetUp machine time. It is not correct?. SetUp imachines time used only for first Production Order for the same product and it is plan manually, for others Production Order we need calculate time for production without SetUp machine time being pick up to compute finish time. how could we achieve this? only those Machine time will be check.
    thanks

Maybe you are looking for