How to restric the calling number in AS5400

HI ,
We are sending the VOIP traffic to few clients , they don't want to recieve the cli from us.I put the clID restrict but still i couldn't screen CLI.pls can you advise me.
reg, kadams

Yes, this can be easily achieved.
1. Create a voice translation rule like this:
voice translation-rule 99
rule 1 /^.*/ //
The 99 is the number of the voice translation rule. If you do not have any other, you might start with 1.
The rule says --> match all numbers (^.*) and replace them with an empty string.
You can change it also like this.
rule 1 /^00/ /011/
this will replace the 00 in the beginning of every number with 011. so, 00359 will become 011359 :)
Then you need to attach this translation rule to a translation profile. Here is an example:
translation-profile removecli
translate calling 99
You attach translation-rule 99 to the translation profile "remove cli" and specify that it will translate calling numbers, not called ones.
The last thing to do is to apply the translation-profile to a dial-peer or voice-port (or a trunk-group as well).
dial-peer example:
dial-peer 100 voip
translation-profile incoming test
This will apply the translation profile for all INCOMING calls to this dial-peer.
Hope that this will solve your issue.

Similar Messages

  • How to prevent voice over saying the caller number or name automatically in iphone?

    hi, i'm a new member of apple world,
    i'm using voice over in my iphone 5s, when i receive a call, voice over automatically say the calling number or name with the ring tone, how can i set
    voice over to prevent it saying the caller number or name ??

    Same problem, which is extremely inconvenient because I like to use my earphones to listen to Pandora while I work. Not every time, but most of the time I plug in my earphones, the iPod software starts playing the last song that was played. Stopping the music via iPod or pressing the Home button for 10 seconds to force quit iPod doesn't stop the music as it will just automatically start playing again. Sometimes if I'm lucky, plugging the earphones in very quickly avoids this problem -- but like I said, it's a cross my fingers and hope I get lucky kind of thing.
    I'm using the newer 3G model, which I've had for only about a month. I did not have this problem with my old 2G iPhone.
    Someone in another thread said it's a hardware fault and suggested exchanging the phone for a new one. Can anyone confirm this?

  • How to prevent voice over saying the calling number ?

    i'm using voice over in my iphone 5s, when i receive a call, voice over autamatically say the calling number or name with the ring tone, how can i set voice over to prevent it saying the caller number or name ?

    It appears to be working as Apple intended. The manual says:
    Moving recordings to your computer
    You can sync voice memos with the iTunes library on your computer, and listen to them on your
    computer or sync them with another iPod touch or iPhone.
    When you delete a synced voice memo from iTunes, it stays on the device where it was recorded,
    but it’s deleted from any other iPod touch or iPhone you synced. If you delete a synced voice
    memo on iPod touch, it’s copied back to iPod touch the next time you sync with iTunes, but you
    can’t sync that copy back to iTunes a second time.
    Sync voice memos with iTunes. Connect iPod touch to your computer. Then in iTunes, select
    iPod touch. Select Music at the top of the screen, select Sync Music, select “Include voice memos,”
    then click Apply.
    Voice memos synced from iPod touch to your computer appear in the Music list and in the Voice
    Memos playlist in iTunes. Voice memos synced from your computer appear in the Voice Memos
    app on iPod touch (but not in the Music app).
    What yo can do is code the Voice Memos on the computer as something besides Voice Memos (Right click>Select Get Info>go to Option tap and change under Media Kind). When yo change it it will move the VM to the library for that kind e.g., Music if you coded it as Music)

  • How to count how many times the caller calls by using UCCX script?

    Hi there,
    My customer wants to do a few changes for their script as below:
    At the beginning of the script they are planning to add a new menu item, it will announce their new privacy policies and to continue the user must press the number one to continue to the Welcome.  If they do not press 1 then the message should repeat itself and if they again do not press 1 they should be transferred over to a live operator who will explain things and then be able to transfer them back to the message so that they can press 1 and continue.
    I modified their script as attached file, but i don't know how to count how many times the caller calls in "Get Reporting Statistic".
    Any helps would be appreciated.
    Thanks.

    Hi Aaron,
    At beginning, i want to use a variable to get number of mistake for the same caller, then we will send the call to right place to fulfill the customers' needs. 
    Do you have any suggestion for the new posted script?
    Thanks.

  • HT2452 How to find the serial number of your Apple hardware product

    How to find the serial number of your Apple hardware product

    This works for any Mac provided that the logic board has not been replaced.
    I recently had the logic board replaced in my iMac. After the tech left (on site repair thanks to Applecare), I went to about the Mac and found jibberish numbers. I called Apple and the AASP and found that he had forgotten to register the serial number. So he came back and, with a special tool (as he called it - looked a little like a USB stick) he contacted Apple and then entered my original serial number as I read it to him.
    So, I assume they changed the process since I still have the same serial number as before.

  • How to delete the Request Number

    Hi all,
                 How to delete the Requset Number in Development Client.Already i transported this Req. Number to Tesing Client.

    For what purpose, deleting the request number won't restore your dev system. You can remove the request from the import queues via transaction STMS to insure it will not be accidentally imported.
    You can usually only destroy a request in source system if it has not been released and all objects are unlocked, but this is risky in some cases and may cause a loss of information or coherence.
    Regards

  • How to retrieve the vendor number during creation of Purchase Order?

    Dear SAP experts,
    For our Purchase Orders, during PO creation (t-code ME21 or ME21N) we want to achieve the following:-
    1) default the delivery address to our plant A address if the vendor is local and
    2) default the delivery address to our plant B address if the vendor is foreign.
    At the moment, we are trying to use the user exit enhancement "MMDA0001" to achieve the above.
    The problem is how to retrieve the vendor number from the screen so we could pass the vendor number to ZXM06U32 to check the ktokk field in LFA1 table in the whether the vendor is foreign or local.
    Thank you in advance.
    Regards,
    Alex

    u can do one thing, create 2 partner function, like 1 for local, and second for import vendor.
    or make 2 batch  n activate vendor batch and make mandatory field from SPRO. 
    then goto SHD0, and do one by one step. first time take 1st requirement and second time take second . like that make two variant .
    i dont know how much it will be helpful. bt i want to suggest smth like that only.
    or, go for ABAPER help
    thanks
    nisha

  • How to get the total number of pages printed in a report?

    Hi All,
    I have a requirement where I need to print a frame of fields only in the last page. Unfortunately I cannot use the 'Print Object On' property as it doesnt work in my case. So, I am planning to write a format trigger on the frame to return TRUE if the page is the last physical page. Now, I need to know how to get the total number of physical pages that will get printed in the report so that I can use this to manipulate the frame. I was planning to use the 'Total Physical Pages' built-in, but it seems like I can just use it to print in a field and I can't use this field's value anywhere in the plsql code (formula column function/format trigger) in the report. Is there anyway to get the total number of pages printed in the report which can be used in the report plsql code?
    Thanks,
    Srini.

    i found the solution, thanks

  • How to get the page number in the break section?

    Hi expert,
    The user wants the page number came right after the Break group name if the break section contains more than 1 page. E.g.
    ABC Compnay
    XXXXXXXXXXX XXXXXXXX
    XXXXXXXXXX XXXXXXXXXXXX
    BCD Company, p 1
    XXXXXXXXXXX XXXXXXXX
    XXXXXXXXXX XXXXXXXXXXXX
    BCD Company, p 2
    XXXXXXXXXXX XXXXXXXX
    XXXXXXXXXX XXXXXXXXXXXX
    CDE Company
    XXXXXXXXXXX XXXXXXXX
    XXXXXXXXXX XXXXXXXXXXXX
    How to get the page number in section break level?

    Hi Wes
    * Create a Field on the margin.
    * Set its "Source" to "Page Number"/"Physical Page Number".
    * Click "Page Numbering" button.
    * In "Reset At" list box, choose the Repeating frame that surrounds your detail group in the layout.
    This should cause Reports to increment the page number until the "Company" repeating frame resets.
    Regards
    Sripathy

  • How to stop the call summary display on home screen?

    How to stop the call summary display on home screen?

    Here are the solutions I can think of (if no one here responds with something better):
    1. Open Settings and then Phone within the Settings screen and see if you can find a setting there for the call summary. The Phone submenu under Settings would be the most likely place.
    2. Open Settings on your iPhone and go through each item including all of the items within each main item. Within about 10 minutes you should be able to get through all of the settings and find the setting if it exists on your phone. There is no such setting on my phone but it is possible that Airtel has a custom menu with that.
    3. If you still haven't found it, you could check a) Airtel's support site and/or b) an Airtel specific forum.
    4. If still no luck, I would call Airtel and ask again and if you get the same response ask for the location of the setting (or to speak to someone who can tell you).
    Good luck.

  • How to hide the PORT NUMBER from the URL

    Hi,
    We have Application on Node 1 and Database on Node 2
    Apps Version: 11.5.10.2
    DB: 9.2.0.6
    We recently added a new node to act as web server for iSupport.
    Now we are able to access the url using public Ip-address which looks like
    http://<Internet Ip-Address>:<PORT NUMBER>
    Eg: http://******.com:8000
    But we dont want the *'PORT NUMBER(8000)'* to be displayed.
    How to hide the port number ?..
    Thanks in Advance,
    Mahesh

    Hi Hsawwan,
    Can you plz explain me the steps how to hide the port number from the url as our network administrator is not aware of this.
    Regards,
    Mahesh

  • How to initiate the call JDBC_Sender adapter from BPM?

    Hello,
    I have a periodicall proccess in BPM. After receiving some message in BPM  I check some fileds of the message.If condition is true I need to initiate SQL request to external DB, to receive the message and send it after transformating to SAP.
    How to initiate the call JDBC_Sender adapter from BPM? As I understand I need to use JDBC Sender adapter and once.
    How to construct the correct BPM?
    Thank You

    the message comes into BPM. You check for some conditions and if true use a send step (Sync) that would query into DB table and as a reponse retrieve the related data. After the send sync step have the transformation step and another send step to SAP.
    U would not configure sender jdbc but u wud need to config for recv jdbc. this wuld service the request and in response return the set of data from the table
    Message was edited by:
            Prabhu  S

  • How to get the Page Number in CS3 with VB?

    Hi, Everybody
    I use the Visual Basic to read the words and their page number where the Words are at. I want to do it according to Story. Some TextFrame of the Story waw placed in other pages: How can I get the Page number according to the Word that is selected?
    For myStoryCounter = 1 to Document.Stories.Count
    Set myStory = Document.Stories.Item(myStoryCounter)
    For myWordCounter = 1 to myStory.Words.Count
    Set myWord = myStory.Words.Item(myWordCounter)
    myWordContents = myWord.Contents
    Rem ** How to Get the Page Number according to the Word ***
    Next
    Next

    > But I don't understand why Item(1) are set.
    because Word can have more than one parent TextFrame - when split across TextFrames
    only Character have one ParentTextFrame accessed also by ParentTextFrames.Item(1)
    > why Story.TextFrames.Count alway is 0, Is it bug?
    no - it's not bug
    in older IDs - Story.TextFrames collection refer to all TextFrames as containers for Story text
    but in CS3 - collection Story.TextFrames contain all TextFrames inserted as InLine/Anchored objects - same like Story.Rectangles or Story.Ovals
    in CS3 - when you want to refer to TextFrames as containers for Story text - you need to use Story.TextContainers - because now you can link TextFrame and Text-On-Path as Story - Text-On-Path isn't TextFrame
    robin
    www.adobescripts.com

  • How to clear the page number in the Script

    Hi Guys,
    I have developed a Script, the same output I need to display with three times with different heading, right now I am able to display the three time with different heading, but the pages are displaying like 1,2,3,4,5,6.
    I need to display the page number 1,2,1,2,1,2, once the heading changes, I need to display page number from I, but I could not able to clear the Page number, could any one please suggest how to create the page number in LAYOUT.
    Thanks,
    Gourisankar.

    Sloved

  • How to get the document number for a ware house order.

    Hello gurus,
    how to get the document number for a ware house order. [if GI is posted refering that WH order] .. is there any report?
    Thanks in advance

    There are several options.  When you post a Goods Movement, you can use LB12 -display Transfer Requirement for material document or LB11 Display TR for material.
    Depending on how your system is set up you may have gotten a Transfer Order automcatically.  In this case you can look at LT24 - Transfer Order for material.

Maybe you are looking for