How to set a maximum download size per connection in the ASA?

Hi, I would like to avoid big downloads so I want to set a maximum download file size. How can I set the limit MB allowed per connection in the ASA?
Thanks

Hello Andrew,
I got your question, but I think we might be confused here, I did not specify something after the timeout but when you configure it you will see you have the same options
Here is the configuration options on 8.2.5
ciscoasa(config-pmap-c)# set connection timeout ?
mpf-policy-map-class mode commands/options:
dcd          Configure dead-connection-detection retry interval.
embryonic    Configure absolute time after which an embryonic TCP connection
               will be closed, default is 0:00:30.
half-closed Configure idle time after which a TCP half-closed connection
               will be freed, default is 0:10:00
idle         Configure idle time after which a connection state will be
               closed.
Now on an ASA running 8.4.4(9)
WPLG-ASA-1(config-pmap-c)# set connection timeout ?
mpf-policy-map-class mode commands/options:
dcd          Configure dead-connection-detection retry interval.
embryonic    Configure absolute time after which an embryonic TCP connection
               will be closed, default is 0:00:30.
half-closed Configure idle time after which a TCP half-closed connection
               will be freed, default is 0:10:00
idle         Configure idle time after which a connection state will be
               closed.
So as you can see same options, no change at all
Hope that I could help
Remember to rate all of the helpful posts

Similar Messages

How we will know that dimension size is more than the fact table size?

how we will know that dimension size is more than the fact table size?

Hi,
Let us assume that we are going to take Division and distribution channel in a dimension and assume we have 20 distinct values for Division in R/3 and 30 Distinct values for Distribution channel .So Maximum, we can get 20 * 30 records in dimension table and we can take rough estimation of records in the cube by observing the raw data in source system.
With rgds,
Anil Kumar Sharma .P

How many sets of wireless headphones can I connect to my iPad at one time?

How many sets of wireless headphones can I connect to my iPad at one time?

Did you mean Bluetooth? One. Did you mean FM or infrared, driven from the 3.5mm output jack? Any number of them, assuming you use the same frequency to receive the stream.

How to set one row or node 's height in the jtree?

How to set height of one row or node in the jtree?
I found the method :jTree.setRowHeight(height);.
But I want to set height of one row ,not all rows of a jtree.
Thanks for help!

Who can help me?

How do i fix my wifi if it connects and the bars are blue but no check sign appears next to the wifi name and does not connect to the internet???

How do i fix my wifi if it connects and the bars are blue but no check sign appears next to the wifi name and does not connect to the internet???

Did you already try to reset the iPod by holding the sleep and home button for about 10sec, until the Apple logo comes back again? You will not lose data.
If this does not work, try to reset the network settings in Settings/General/Reset. After that you'll have to put in the passwords for all known networks again.
More troubleshooting can be found here:
iOS: Troubleshooting Wi-Fi networks and connections

Rented movie does not play after download if not connected to the internet

rented movie does not play after download if not connected to the internet

Hello b noir.
Thank you for your interest in solving my problem.
What I did I opened iTune. I read the information about what does my computener need to play back a rented movie. My computer is okay to play back rental movies. So I went to the iTunes store, I searched for the movie I want to watch, i singned in into my Mac account and I bought the movie. The movie started to download to my computer, it took some time because I bought a HD version, but it never stop and after a couple of hours or little less the movie was in the Rented folder of my iTunes and also I checked to be sure that was in the movie folder. So, next day I open iTunes and click on the movie, it opens but I wait for five minuetes and never started to play back, so I tried several time and I looked for info in different internet forums but I couldn't find anything that help. So I posted the problem in this forum and also I called Apple. Apple contacted me and they let me to download the movie again. So I did it and now I will watch the movie later. Not sure if the movie will play back normally or if I am going to have the same problem. I'll keep you posted.
Apple representative did not know why this happened.
Thanks.

How many 3440 x 1440 monitors can you connect to the latest MacPro?

How many 3440 x 1440 monitors can you connect to the latest MacPro?

Apple is not clean in:
Mac Pro (Late 2013): Using multiple displays - Apple Support
It includes
Can I connect more than 2 DVI or HDMI displays?
Mac Pro supports a total of two DVI or HDMI displays when connected via the built-in HDMI port or using the Apple Mini DisplayPort to DVI adapter. To connect additional DVI displays, use an active DVI adaptersuch as the Apple Mini DisplayPort to Dual-Link DVI adapter. You can connect up to six active adapter DVI displays. This requires a powered USB hub since Mac Pro offers four USB ports and you will need six to connect them all.
However, that article says:
Six Apple Thunderbolt Displays (27-inch), Apple LED Cinema Displays (27-inch), or third-party Mini DisplayPort displays.
So it appears you can with active dual-link DVI adopter or monitors with a display/min displayport connection.

Forms: How to set a maximum size in Text Fields with automatic size

¡Hi!
When I set a text field on my forms and I use automatic size for te text that the user can write, if the user don't need more space than the field size, when the text appears, Adobe Acrobat Pro always set the text-size to 14 or higher. How can I set a maximum size for that text? For example... 12 or 10...
Thank you very much,
Best regards from Spain,
David.

Ok. If I use a single line text field, changing the height of the field seems to be a simple way to solve the problem, but... what should I do when the fields are multi-lineal?
Thanx for your quick answer.

Struggling how to set up 2 daq assist on labview in the same VI

hi all,
hope someone can help me out
I am currently using the scxi 2345 with some SCC FT01 feed through modules, these are just to record some voltages from some transducers.
What I am struggling with is setting up 2 daq assist on a single VI, it is coming back with a error stating specified resouce is reserved and then a window saying learn more about automatic handling. How would I also have these 2 values logged on the same graph or chart?
Anyone any ideas how to set these up.
I ideally want to have 3 daq assist in the same Vi but not sure if this is possible. It would be 1 for thermocouple input and 2 for voltage as stated above
many thanks
shane dover

Hi Shane and Dennis,
I've been working my way around the same type of problems, and I am
currently re-writing everything to use on Asst. per board on my PXI
chassis, so that no resources become reserved.
As a result, I have to separate the signals on the output dynamic data
in order to do different post processing. So I have been toying
with staying with dynamic data, inputting dyn. data into an array, and
inputing it into a cluster. It seems that each has advantages and
drawbacks, but arrays seem to be the easiest with which to work when
splitting signals coming from a DAQmx Asst. and funneling some of the
signals into a post-processing sub-VI. The drawback to this is
that time stamps in the Dyn. Data are lost if you want to record the
data and the time of the reading.
Question: Is there an easy way to pipe Dynamic Data into a
calculation subVI? Is it workable after it's been split from
other streams?
Thanks,
Brad

Macbook pro default maximum screen size does not cover the bottom inch

Kind of frustrated by my new macbook pro.
At the bottom of the screen, there's the icon bar (icon dock), which is about inch height. I adjusted it to smaller size, about half inch. This is what I did, not sure if related to my problem.
At the beginning, I thought it was Safari's problem. Later I found all programs has the problem. I'll use Safari as example to describe the problem though.
When I open Safari, it does not expand to the bottom inch of the screen, as if the icon dock prevents it expanding to the icon bar area of original icon bar size (i.e., inch, not half inch I'm using), and as if there was a line at the bottom inch. I click the plus sign (maximum screen), it still leave the inch uncovered. However, if I use full screen modle, Safari would covers the whole screen.
when not in full screen model, I can drag the bottom edge of Safari, but can only drag to the virtual icon bar line (at bottom inch position). When bottom edge is at the virtual line, the drag arrow is single direction pointing to up. However, I could move Safari to lower and cover the bottom inch area (with icon bar on the top), and then drag the top edge to make it cover all screen area.
What makes more annoying is if a new tab automatically opens, Safari will goes to the size with the bottom inch uncovered. This problem does not happen if program runs in full screen model.
I tried a few programs, all have such problem. Looks to me default maximum screen size excludes the bottom inch (because by default that area is supposed to be occupied by icon bar although I changed the size or just simply hide the icon bar).
Anyone know why? How to solve the problem? TIA.

called Apple, the solution is:
1, turn on sound
2, shutdown
3, press and hold these four keys the same time: left option, left command, R, and P
4, press and release power button to restart
5, after first starting chime sound, continue hold those four keys
6, after second starting chime sound, release keys
this resets some settings --- not sure what is reset though.

How can I get my downloads folder to appear in the docking station

How can I get the download folder to remain on the docking station

Note if you don't have any folders on your Dock, note the trashcan is on one side of the dock with a divider between it and applications. Minimized windows (with the yellow button on the upper left corner) will go between the trash and that divider. You can drag folders into the section between the minimized windows and the trash.

How to set a back ground to be shown in the whole browser...

Hi all,
1. How to set a background in Adobe Dreamweaver so it's gonna be visible in whole browser no matter what resolution is set, the problem is that I cant set to repeat it as the backgroud is not symetric (picture below):
http://a.imagehost.org/view/0568/Untitled-2
2. I would like to know how to create a shiny/glossy objects like rectangle or so in Photoshop. Could you recommended some addons/plugs? An example:
http://www.istockphoto.com/file_thumbview_approve/6137760/2/istockphoto_6137760-shiny-rect angle-menu-buttons.jpg
Thanks from advance for any help.
Regards

Here's an example using the background image you linked to.
http://perrelink.com.au/forum/repeat-bg/
Look at the code and see how I've applied the background image to the body tag in the css.
Nadia
Adobe® Community Expert : Dreamweaver
http://www.perrelink.com.au
Unique CSS Templates | Tutorials | SEO Articles
http://www.DreamweaverResources.com
http://twitter.com/nadiap

How to set proxy for client-server socket connection?

Hi,
I'm using the code found on the following page to create a client (mobile) to server (pc) connection and send a text message.
http://javafaq.nu/java-example-code-503.html
This works with mobile operators without proxy, but does nothing when the operator uses a proxy. The question is, exactly how to set the proxy and port values for using that code.
Any help is greatly appreciated, thanks,

It's part of the cellular settings, and is usually set up by your 3G provider. You can't choose your own proxy server

How to set master cost center to required input in the maintaining position

Dear experts,
I have two questions in the HCM module,could you please tell me?
Issue 1: How to set the column of master cost center to required input in the maintaining position screen?
Issue 2: some of position has two cost center, i have maintained two cost center(cost center 1:90%,cost center 2:10%) percentage in the tab of cost distribution with trasaction code ppome.when i post to accounting,it only post to master cost center 100%,it can not distribute two cost center, Could you please tell me the reason?
Looking forward to your reply.
Best regards,
Merry

HI,
Plz check with ur FICO Consultants as master Cost Center r desgined by them
They will Loop group of Cost Centers to Master Cost Center.
This concept has started in ECC 6.0 Version
Regards,
Kiran

I need to know how to set up my itunes card i bought at the store on my phone please

I need to know how to set up my itunes card that I bought from the store to my account on my phone

Click here and follow the instructions.
(118196)

How to set a maximum download size per connection in the ASA?

Similar Messages

Maybe you are looking for