How to terminate/restart a execution?

I am using simple user interface(LabView) to develop a new custom UI.
But I find the Terminate/Restart Button doesn't work: After I use it to terminate one execution, not able to restart it anymore.
How to restart a terminated execution when run TestUUTs?
I'm appreciate any help on this.
Attachments:
Simple UI Restart not work.JPG ‏59 KB

There are a couple of possibilities for the cause of the issue you are seeing.
1) Terminate is asynchronous, so if you are programmatically terminating the execution and restarting it, the restart might be getting done before the termination is complete. Wait for the execution to complete before restarting it. You can use Execution.WaitEx, UIMessages, or polling with GetStates to tell when the execution is really complete.
2) Executions can be marked as not restartable. The batch model uses this setting (on the new execution sequence call) in order to keep you from incorrectly restarting the socket executions. For the batch model, only the controlling execution should be restarted. Restarting the controlling execution restarts the socket executions automatically.
-Doug

Similar Messages

How to terminate the jsp execution

Hi, I've an problem to terminate the jsp execution.
I've tried to use the following code: out.close();
but the jsp (I use the servlet engine version 2.0) page continue the execution.
How I can terminate this execution?
Thanks

Hello,
i haven't this tried out yet, and i even do not have Time to test it,
but if you use a Custom Jsp Tag, then you can set the return Type of
the doEndTag() Method to SKIP_PAGE.
This should stop the Evaluation of the Rest of Page.
Good Luck !
Best regards
jherunter

How Do You Restart a Failing Load Plan

If a Load Plan step fails, say because of some bad data or a bad join, I know how to correct the error and restart the failing step or the failing task in the Operator.
How do you restart the failing Load Plan or any higher level step in the Operator?
Right now my Load Plan steps all say 'Restart from failed task'.
I can't see the Load Plan itself in the Operator, so I can't restart it directly.

In the Operator, there is an accordion section labeled "Load Plan Executions". You can restart from there.
Regards,
Michael Rainey

Integration Directory - how to terminate all logons?

I was importing RFC definitions from R/3 in ID. Laptop battery went down and got disconnected with SAP XI,IB.
After 5 mins, restarted laptop (powered by wire). Opened same SWCV in Integration Directory to change the connection data to point R3 system instead of XI SAP. It gives message "Object SWCV myswcv is currently being edited by user myIDuserid"
This is what I did sofar, but no luck
-logon to XI system, transaction SM04. Terrminate all connections with SAP XI.
Please advise how to terminate all logons in Integration directory? Thanks

Hi,
You can go to 'index page' click on 'administration'. In that you will find on the left side 'administration of locks and caches'. You can click 'lock overview' and unlock the objects.
Regards,
P.Venkat
Message was edited by:
Venkataramanan

I lost connection with the server while downloading an audio book how do I restart the download without paying again?

I lost connection with the server while downloading an audio book how do I restart the download without paying again?

Go into the App Store, tap Updates, and at the top should appear Purchases. Hit the tab that says "Not on this iPhone" to download again

HT1296 what if you dont have a computer to download iTunes then how can i restart my iPod?

what if you dont have a computer to download iTunes then how can i restart my iPod? because my iPod is telling me to hook it up to iTunes but there is no way for me to do that if i cant download it on a computer i dont have..

You need to connect the iPod to a computer with iTunes and an internet connection and restore via iTunes
iTunes: Backing up, updating, and restoring iOS software

My kids desabled my mini ipad after several tries to log in. My computer that I used to sincronize it doesn't work anymore and i can't connected to itunes.. How can i restart it without the actual computer that I used before??

My kids desabled my mini ipad after several tries to log in. My computer that I used to sincronize it doesn't work anymore and i can't connected to itunes.. How can i restart it without the actual computer that I used before??

You can use any computer but your data will be lost if you have no backup.

HT1661 How can I restart my mac book pro 11 inches when it's on target disc mode

How can I restart my mac book pro 11 inches when it's on target disc mode

Even if you could open Disk Utility you can't reformat a disk while you are booted from it. You will have to use the install CD. Ring the Apple Online Store at the number given at bottom left of this page and give them the serial number of your Mac. You should be able to get the Snow Leopard install disks for a nominal fee.

How can I stop the execution on a JSP page and start it again

Hi
I am making a program that simulates how to manage transactions when accessing a database by using locks. I have run into a problem and I hope someone has the time to help me.
When a user does an update the transaction commits and releases its locks when the program executes
<%stmt.executeUpdate("commit!"); %>
I need to put a break in to stop the program executing this statement, to illustrate the lock is set correctly.
I have tried to put in an alert box but this does not prevent the rest of the java code being executed.
I have tried to use prompt boxes, JavaScript functions, but these functions cannot have any java code in them.
I have tried using the java.swing JOptionPane boxes but this didn?t work either
I have tried to get input from the user but I don?t know how to retrieve this data on the same page. (As far as I know you have to use submit and even refresh the page or retrieve it on the next page).
Does anyone know how I can stop the execution on a JSP page and start it again (on same page)
Mette

I already have another client (Tomcat jsp application) running and it throws a SQLException correctly when I don�t put in a commit=true statement and don't close the database connection.
But the problem is how to get the code above to stop to illustrate I have set this lock.
I have tried to use the JOptionPane but because my program is running in a web browser I cannot use the JOptionPane dialog box.
I have tired using an alert box but it executes the commit statement before the alert box is dispayed. So this does not work
While (i < 2)
if( i==1)
%>alert(�The transactions commits when you press Ok�); <% //what it to stop execution here
else
stmt.executeUpdate(�commit�);
I am not using threads so I cannot use the sleep function.
I am using mysql and have already configured it to detect deadlocks and how long to wait for locks.
Thanks for your help
Mette

TS1363 how can i restart my 2004 ipod click wheel?

How can i restart my 2004 model ipod (click wheel) on my computer and on my itunes?

Connect the iPod nano to the computer the exact same way you set up the old one. You don't need to create another Apple ID, iTunes Store account, or iTunes library.
(98196)

How can I make the execution of my script faster

Hi everyone
How can I make the execution of my script faster, because it takes a lot of time to execute? The following is my script:
DECLARE
CURSOR C1 IS
SELECT A.ITEM_CODE,A.STORE_CODE,ST_UNIT,SA_UNIT,CART_QTY,QUANTITY_ON_HAND
FROM PROJ.IM_LOCATION A
WHERE A.ITEM_CODE BETWEEN :ITEM_FRM AND :ITEM_TO
AND A.STORE_CODE = :FRM_STORE
ORDER BY
A.STORE_CODE ;
CURSOR C2 IS
SELECT A.ITEM_CODE,A.STORE_CODE,ST_UNIT,SA_UNIT,CART_QTY,QUANTITY_ON_HAND
FROM PROJ.IM_LOCATION A
WHERE A.ITEM_CODE BETWEEN :ITEM_FRM AND :ITEM_TO
AND A.STORE_CODE = :FRM_STORE
ORDER BY
A.STORE_CODE ;
big_syb_qty_issue number(12,3);
small_syb_qty_issue number(12,3);
big_issue number(12,3);
small_issue number(12,3);
item_syb_code varchar2(30);
big_syb_qty_rec number(12,3);
small_syb_qty_rec number(12,3);
BI_SUPP_REC number(12,3);
SM_SUPP_REC number(12,3);
big_syb_qty_ADJ number(12,3);
small_syb_qty_ADJ number(12,3);
big_ADJ number(12,3);
small_ADJ number(12,3);
big_syb_qty_rec_iner number(12,3);
small_syb_qty_rec_iner number(12,3);
BI_INTER number(12,3);
SM_INTER number(12,3);
cl_big_qty number(12,3);
cl_small_qty number(12,3);
cl_big_qty1 number(12,3);
cl_small_qty1 number(12,3);
BIG_QTY_OPEN number(12,3);
SMALL_QTY_OPEN number(12,3);
BEGIN
     IF ((:FRM_STORE IS NULL) OR (:ITEM_FRM IS NULL) OR (:ITEM_TO IS NULL) OR (:DATE_FRM IS NULL)) THEN
          SHOW_MESSAGE('You Should Enter the Parameters Values Correctly Please try again !!!! ');
          RAISE FORM_TRIGGER_FAILURE;
          GO_FIELD('DATE_FRM');
     END IF;
DELETE FROM STOCK_AT_DATE_REP2;
COMMIT;
cl_big_qty := 0;
cl_small_qty := 0;
-- MESSAGE('Please Wait The System Calculating The Transactions !!!');
SET_APPLICATION_PROPERTY(CURSOR_STYLE,'BUSY');
FOR R IN C1
LOOP
cl_big_qty := R.CART_QTY ;
cl_small_qty := R.QUANTITY_ON_HAND;
-- Transerfer Data 1
BEGIN
SELECT B.ITEM_CODE,SUM(NVL(CART_QTY,0)) ,SUM(NVL(ITEM_QUANTITY,0))
INTO item_syb_code,big_syb_qty_issue,small_syb_qty_issue
FROM IM_TRANS_ISSUE_HEADER A,IM_TRANS_ISSUE_DETAILS B
WHERE A.DOC_CODE = B.DOC_CODE
AND B.DEL_STORE = R.STORE_CODE
AND ITEM_CODE = R.ITEM_CODE
AND DOC_DATE > :DATE_TO
GROUP BY
B.ITEM_CODE;
-- SHOW_MESSAGE('ISSUED BIG'||' '||big_syb_qty_issue);
exception
when no_data_found then big_syb_qty_issue := 0;
small_syb_qty_issue := 0;
when others then MESSAGE(10,sqlerrm);
END ;
-- Goods Received Data From Supplier 1
BEGIN
SELECT B.ITEM_CODE,SUM(B.CART_QTY),SUM(ITEM_QUANTITY)
INTO item_syb_code,big_syb_qty_rec,small_syb_qty_rec
FROM IM_GOODS_RECIEVE_HEADER A,IM_GOODS_RECIEVE_DETAILS B
WHERE A.DOC_CODE = B.DOC_CODE
AND STORE_CODE = R.STORE_CODE
AND ITEM_CODE = R.ITEM_CODE
AND DOC_DATE > :DATE_TO
GROUP BY
B.ITEM_CODE;
-- SHOW_MESSAGE('RECEIVED FROM SUPPLIER BIG'||' '||big_syb_qty_rec);
exception
when no_data_found then big_syb_qty_rec := 0;
small_syb_qty_rec := 0;
when others then message(10,sqlerrm);
END ;
-- Adjustement Data 1
BEGIN
SELECT B.ITEM_CODE ,SUM(NVL(CART_QTY,0)) ADJUST_QTY,SUM(NVL(ITEM_QUANTITY,0))
INTO item_syb_code,big_syb_qty_ADJ,small_syb_qty_ADJ
FROM IM_ADJUST_HEADER A,IM_ADJUST_DETAILS B
WHERE A.DOC_CODE = B.DOC_CODE
AND B.STORE_CODE = R.STORE_CODE
AND ITEM_CODE = R.ITEM_CODE
AND A.DOC_DATE > :DATE_TO
GROUP BY
B.ITEM_CODE;
-- SHOW_MESSAGE('Adjust BIG'||' '||big_syb_qty_ADJ);
exception
when no_data_found then big_syb_qty_ADJ := 0;
small_syb_qty_ADJ := 0;
when others then message(10,sqlerrm);
END ;
-- Goods Received Data From Stores 1
BEGIN
SELECT B.ITEM_CODE,SUM(B.CART_QTY),SUM(ITEM_QUANTITY)
INTO item_syb_code,big_syb_qty_rec_iner,small_syb_qty_rec_iner
FROM IM_TRANS_REC_HEADER A,IM_TRANS_REC_DETAILS B
WHERE A.DOC_CODE = B.DOC_CODE
AND REC_STORE = R.STORE_CODE
AND ITEM_CODE = R.ITEM_CODE
AND DOC_DATE > :DATE_TO
GROUP BY
B.ITEM_CODE;
-- show_message('here');
-- SHOW_MESSAGE('Received From Stores BIG'||' '||big_syb_qty_rec_iner);
exception
when no_data_found then
big_syb_qty_rec_iner := 0;
small_syb_qty_rec_iner := 0;
when others then message(10,sqlerrm);
END ;
cl_big_qty := (NVL(cl_big_qty,0) + NVL(big_syb_qty_issue,0));
cl_big_qty := (NVL(cl_big_qty,0) - NVL(big_syb_qty_rec,0));
cl_big_qty := (NVL(cl_big_qty,0) - NVL(big_syb_qty_rec_iner,0));
big_syb_qty_ADJ := -1 * NVL(big_syb_qty_ADJ,0);
cl_big_qty := (NVL(cl_big_qty,0) + NVL(big_syb_qty_ADJ,0));
-- srw.message(2000,'cl_small_qty'||cl_small_qty);
cl_small_qty := (NVL(cl_small_qty,0) + NVL(small_syb_qty_issue,0));
cl_small_qty := (NVL(cl_small_qty,0) - NVL(small_syb_qty_rec,0));
cl_small_qty := (NVL(cl_small_qty,0) - NVL(small_syb_qty_rec_iner,0));
small_syb_qty_ADJ := -1 * NVL(small_syb_qty_ADJ,0);
cl_small_qty := (NVL(cl_small_qty,0) + NVL(small_syb_qty_ADJ,0));
-- srw.message(2000,'cl_small_qty'||cl_small_qty); srw.message(2000,'cl_small_qty'||cl_small_qty);
INSERT INTO STOCK_AT_DATE_REP2
VALUES(R.STORE_CODE,R.ITEM_CODE,cl_big_qty,cl_small_qty,R.ST_UNIT,R.SA_UNIT,:DATE_FRM,
:DATE_TO,0,0,0,0,0,0,0,0,cl_big_qty,cl_small_qty);
cl_big_qty := 0;
cl_small_qty := 0;
END LOOP;
COMMIT;
FOR R IN C2
LOOP
-- Transerfer Data 2
BEGIN
SELECT B.ITEM_CODE,SUM(NVL(CART_QTY,0)) ,SUM(NVL(ITEM_QUANTITY,0))
INTO item_syb_code,big_issue,small_issue
FROM IM_TRANS_ISSUE_HEADER A,IM_TRANS_ISSUE_DETAILS B
WHERE A.DOC_CODE = B.DOC_CODE
AND B.DEL_STORE = R.STORE_CODE
AND ITEM_CODE = R.ITEM_CODE
AND DOC_DATE BETWEEN :DATE_FRM AND :DATE_TO
GROUP BY
B.ITEM_CODE;
-- SHOW_MESSAGE('ISSUED BIG'||' '||big_syb_qty_issue);
exception
when no_data_found then
big_issue := 0;
small_issue := 0;
when others then MESSAGE(10,sqlerrm);
END ;
-- Goods Received Data From Supplier 2
BEGIN
SELECT B.ITEM_CODE,SUM(NVL(B.CART_QTY,0)),SUM(NVL(ITEM_QUANTITY,0))
INTO item_syb_code,BI_SUPP_REC,SM_SUPP_REC
FROM IM_GOODS_RECIEVE_HEADER A,IM_GOODS_RECIEVE_DETAILS B
WHERE A.DOC_CODE = B.DOC_CODE
AND STORE_CODE = R.STORE_CODE
AND ITEM_CODE = R.ITEM_CODE
AND DOC_DATE BETWEEN :DATE_FRM AND :DATE_TO
GROUP BY
B.ITEM_CODE;
-- SHOW_MESSAGE('1- SM_SUPP_REC '||' '||SM_SUPP_REC );
-- SHOW_MESSAGE('RECEIVED FROM SUPPLIER BIG'||' '||big_syb_qty_rec);
exception
when no_data_found then
BI_SUPP_REC := 0;
SM_SUPP_REC := 0;
when others then message(10,sqlerrm);
END ;
-- Adjustement Data 2
BEGIN
SELECT B.ITEM_CODE ,SUM(NVL(CART_QTY,0)) ADJUST_QTY,SUM(NVL(ITEM_QUANTITY,0))
INTO item_syb_code,big_ADJ,small_ADJ
FROM IM_ADJUST_HEADER A,IM_ADJUST_DETAILS B
WHERE A.DOC_CODE = B.DOC_CODE
AND B.STORE_CODE = R.STORE_CODE
AND ITEM_CODE = R.ITEM_CODE
AND A.DOC_DATE BETWEEN :DATE_FRM AND :DATE_TO
GROUP BY
B.ITEM_CODE;
-- SHOW_MESSAGE('Adjust BIG'||' '||big_syb_qty_ADJ);
exception
when no_data_found then
big_ADJ := 0;
small_ADJ := 0;
when others then message(10,sqlerrm);
END ;
-- Goods Received Data From Stores 2
BEGIN
SELECT B.ITEM_CODE,SUM(NVL(B.CART_QTY,0)),SUM(NVL(ITEM_QUANTITY,0))
INTO item_syb_code,BI_INTER,SM_INTER
FROM IM_TRANS_REC_HEADER A,IM_TRANS_REC_DETAILS B
WHERE A.DOC_CODE = B.DOC_CODE
AND REC_STORE = R.STORE_CODE
AND ITEM_CODE = R.ITEM_CODE
AND DOC_DATE BETWEEN :DATE_FRM AND :DATE_TO
GROUP BY
B.ITEM_CODE;
-- show_message('here');
-- SHOW_MESSAGE('Received From Stores BIG'||' '||big_syb_qty_rec_iner);
exception
when no_data_found then
BI_INTER := 0;
SM_INTER := 0;
when others then message(10,sqlerrm);
END ;
BEGIN
     BIG_QTY_OPEN := 0;
SMALL_QTY_OPEN := 0;
BEGIN
SELECT NVL(S_BIG_QTY_OPEN,0) ,NVL(S_SMALL_QTY_OPEN,0)
INTO
BIG_QTY_OPEN,SMALL_QTY_OPEN
FROM STOCK_AT_DATE_REP2
WHERE S_STORE_CODE = R.STORE_CODE
AND S_ITEM_CODE = R.ITEM_CODE;
END;
BIG_QTY_OPEN := ((BIG_QTY_OPEN) + NVL(big_issue,0));
BIG_QTY_OPEN := ((BIG_QTY_OPEN) - NVL(BI_SUPP_REC,0));
big_adj := -1 * NVL(big_adj,0);
BIG_QTY_OPEN := ((BIG_QTY_OPEN) + NVL(big_adj,0));
BIG_QTY_OPEN := ((BIG_QTY_OPEN) - NVL(BI_INTER,0));
SMALL_QTY_OPEN := ((SMALL_QTY_OPEN) + NVL(SMALL_issue,0));
SMALL_QTY_OPEN := ((SMALL_QTY_OPEN) - NVL(SM_SUPP_REC ,0));
SMALL_adj := -1 * NVL(SMALL_adj,0);
SMALL_QTY_OPEN := ((SMALL_QTY_OPEN) + NVL(SMALL_adj,0));
SMALL_QTY_OPEN := ((SMALL_QTY_OPEN) - NVL(SM_INTER,0));
END;
BEGIN
UPDATE STOCK_AT_DATE_REP2
SET BIG_SUP_REC = BI_SUPP_REC,
SMALL_SUP_REC = SM_SUPP_REC,
BIG_ISSUE_TRAN = big_issue,
SMALL_ISSUE_TRAN = SMALL_issue,
BIG_ADJUST = big_adj,
SMALL_ADJUST = SMALL_adj,
BIG_INTER_REC = BI_INTER,
SMALL_INTER_REC = SM_INTER,
S_BIG_QTY_OPEN = BIG_QTY_OPEN,
S_SMALL_QTY_OPEN = SMALL_QTY_OPEN
WHERE S_STORE_CODE = R.STORE_CODE
AND S_ITEM_CODE = R.ITEM_CODE;
exception
when no_data_found then
NULL;
when others then
message(10,sqlerrm);
END;
END LOOP;
COMMIT;
SET_APPLICATION_PROPERTY(CURSOR_STYLE,'default');
SYNCHRONIZE;
-- SHOW_MESSAGE('The Data Have Been Calculated !!!');
END;
declare
     pl_id ParamList;
APPLICATION_ID VARCHAR2(20):='PRD';
          COMMAND_LINE VARCHAR2(100) :='STOCK_LEDGER';
BEGIN
pl_id := Get_Parameter_List('tmpdata');
IF NOT Id_Null(pl_id) THEN
Destroy_Parameter_List( pl_id );
END IF;
pl_id := Create_Parameter_List('tmpdata');
Add_Parameter(pl_id,'DATE_FRM',TEXT_PARAMETER,:DATE_FRM);
Add_Parameter(pl_id,'DATE_TO',TEXT_PARAMETER,:DATE_TO);
Add_Parameter(pl_id,'ITEM_FRM',TEXT_PARAMETER,:ITEM_FRM);
Add_Parameter(pl_id,'ITEM_TO',TEXT_PARAMETER,:ITEM_TO);
Add_Parameter(pl_id,'FRM_STORE',TEXT_PARAMETER,:FRM_STORE);
IF :REPORT_TYPE = 1 THEN
Run_Product(REPORTS,'C:\INV\RDF\STOCK_LEDGER.rdf',SYNCHRONOUS,RUNTIME,
FILESYSTEM, pl_id,NULL);
ELSIF :REPORT_TYPE = 2 THEN
Run_Product(REPORTS,'C:\INV\RDF\STOCK_LEDGER_2.rdf',SYNCHRONOUS,RUNTIME,
FILESYSTEM, pl_id,NULL);
END IF;
END;
Waiting for your valuable answer
Best Regards
Jamil Alshaibani

Make a matte in Photoshop.
From the Photoshop menu bar: File > New > Film & Video Presets. Choose one that suits your FCP project pixel dimensions. Make the background black. Place a white rectangle with rounded corners on top (the white will determine how much of your picture is visible). Flatten Image. Save as TIFF. Import into FCP.
Move your video clips up to V2. Place the imported TIFF on V1. Highlight all clips on V2.
Go to Modify > Composite Mode > Travel Matte Luma. Done.
If you want soft edges, no need for a matte. Double click your clip to place it in the Viewer. Open up the Motion tab > Crop > Edge Feather. Nice and quick. Copy and Paste attributes for the other clips.

How do I restart Time Machine back-up from scratch?

How do I restart Time Machine back-up from scratch? I have a MacBook Air that was my wife's - now given to my daughter for school. My wife never used Time Machine to back up (she simply copied files to an external drive), so before clearing her files off the Mac HD, I tried using Time Machine for the first time with an external HD. However, the Time Machine back up repeatedly failed after about 2GB of 28GB of files. I manually copied my wife's 28GB of files to another external HD and deleted all the files off the Mac HD. I then reformatted the external Time Machine drive. But when I try to use Time Machine to back up the MacBook Air as it is now with my daughter's files on the Mac HD to the external TM drive, Time Machine acts as if the 28GB of my wife's deleted files are still on the Mac HD and fails back-up after counting to about 2GB, even though there aren't even 2GB of files on the Mac HD now and nothing on the external TM drive. I don't need to save any back-ups of how the MacBook used to be - I just need to start from scratch with how the computer is now. Can anyone please tell me how to get Time Machine to think the MacBook is a brand new computer and act as if it's a first time ever back up? I tried updating to Yosemite, and tried renaming the computer in System Preferences>Sharing, plus (as noted above) deleting all the old files off the Mac HD and reformatting the external Time Machine drive - none of that worked. All I can do at the moment is manually copy my daughter's files to an external HD - very frustrating.

Hmmm.. Office is not hard to restore.
You have something major wrong (Yosemite being the primary one).
Do a verify of the source drive.. to do that you will need to boot to the recovery.. and run the disk utility from there.. it sounds like your main disk is corrupted.
Once that is complete, delete the current setup of TM and try again.. use the widget to find out why it is failing..
See Troubleshooting.
A1, A4 and A5 for further info.
http://pondini.org/TM/Troubleshooting.html
Good luck with it..
I would also download carbon copy cloner.. it is $40, but you can use it free for a time.. forget if a week or a month??.. to try out.. and make a proper backup before you start.. CCC is far more reliable than TM.. and in fact you might decide to simply forget about TM if it works and pays the $40.. because you can produce a bootable clone on the external drive which is a heck of a lot easier to use than TM.

HT1430 How can you restart your iphone if your lock button does not work?

How can you restart or turn off your iPhone if the lock button does not work?

The best way is to let the battery die. Or you can reset the phone settings which restarts everything.

How to capture the first execution of a report

Hi,
I am executing a report in background. The first time the report is executed I have to do a different processing. After the 1st execution I have to different processing.
Someone please tell me how to capture the 1st execution of a report. Is there a system variable ?
Appreciate your <removed by moderator> response.
Thanks,
Dikshitha G
Edited by: Thomas Zloch on May 12, 2011 11:36 AM

Keshav.T wrote:
Are you going to create a Z table for this ???? ... Is there nobody to advice you in your firm ???
Hello Keshav,
A couple of years ago i would have recommended using the INDX table, but it has got it's demerits.
Maintenance of Z-table is easier than the INDX table. Say there is some error in the program & you want to override the flag. Will it be easier to do so in the INDX table or via SM30 for the Z-Table?
As a matter-of-fact i will recommend using the solution provided by Florian the TVARVC technique.
1. Create a parameter(specific to your program) & transport it.(See the trxn STVARV)
2. In your program check the value of this param & set it accordingly.
Using TVARVC you will 2 birds with one stone:
1. You don't have to create a custom table.
2. Easy maintenance via STVARV trxn.
Hope you get the point!
Cheers,
Suhas
PS: In our system we have a Z-table designed specifically for this particular purpose. All the programs having this kind of requirement refer to this table.

How to terminate a java thread from c++ code?

Hi,
I made a screensaver which loads a jvm, forks a thread running a java class, wait until user's action(i.e. mouse move/click keyboard input), then terminate the java thread.
However, I met a problem, How to terminate a running java thread from c++ code?
Here is my code, but it does not work: (even after the terminate is called, jvm throws an error)
JNIEnv* env;
JavaVM* jvm;
HANDLE hThread; //handle for the startThread
unsigned __stdcall startThread(void *arg)
     jclass cls;
     jmethodID mainId;
     jint          res;
     int threadNum = (int)arg;
     res = jvm->AttachCurrentThread((void**)&env, NULL);
cls = env->FindClass( MAIN_CLASS);
     mainId = env->GetStaticMethodID(cls, "main", "([Ljava/lang/String;)V");
     // setup the parameters to pass to main()
     jstring str;
     jobjectArray args;
     int i=0;
     args = env->NewObjectArray(1, env->FindClass("java/lang/String"), 0); //only one input parameters
     str = env->NewStringUTF("localhost");
     env->SetObjectArrayElement(args, 0, str);
     env->CallStaticVoidMethod(cls, mainId, args); // call main()
     if (env->ExceptionOccurred()) {
               env->ExceptionDescribe();
     return TRUE;
Here is the main method:
First create the jvm and load the thread. then tries to terminate the thread, but failed here
switch (msg)
{ case WM_CREATE:
          JavaVMOption options[NUMBEROFOPTIONS];
          JavaVMInitArgs vmargs;
          jint rc;
          vmargs.version = JNI_VERSION_1_4; /* version 1.4 */
          vmargs.options = options;
          vmargs.nOptions = NUMBEROFOPTIONS;
          vmargs.ignoreUnrecognized = JNI_FALSE;
          rc=JNI_CreateJavaVM( &jvm, (void **)&env, &vmargs ); /* create JVM */
          /* We pass the thread number as the argument to the invoked thread */
          unsigned int threadId = -1;
          // to initialize a thread-safe C runtime library
          hThread = (HANDLE)_beginthreadex(NULL, 0, &startThread, NULL, 0, &threadId );
} break;
case (WM_DESTROY):
          CloseHandle( hThread );
          jvm->DestroyJavaVM(); /* kill JVM */
          Debug("Destroy Java Virtual Machine\n");
}break;
Note, after the thread "startThread" runs, it has an infinite loop and will not terminate, until the user clicks to terminate.(I didn't call jvm->DetachCurrentThread();_endthreadex(0); in the "startThread" because the java thread will not terminate by itself)
Thus, the only way to terminate the thread is to call closehandle(hthread) in the main thread, which may cause jvm to throw an error.
Do you know how to terminate a java thread safely???
Thanks a lot

Assuming that your java thread is in a loop of some kind. Such as
int i=1; /* I tried using a boolean, I just could not get my C++ env, to change this value. So i decided to use an int */
run {
while(i)
isdfjsdfj
void seti()
i=0
So, B/4, i call destroyVM in my C++ code, i call this seti(). so the loop terminates, therefore my thread finishes executing and ends.
Hope this helps
tola.

How to terminate/restart a execution?

Similar Messages

Maybe you are looking for