How to use AirPort Express over a dorm network

Hi,
I used my AirPort Express at home to add wireless to my existing home network and it worked well.
However, I can't get it to work here so I'll give you every detail possible in order for you to explain me how to configure it. A million thanks in advance. (I'm giving you the specific address just to illustrate it better)
I can only use one IP address on the network which is 192.168.1.25
The subnet mask is 255.255.255.0
The default getaway is 192.168.1.1
The preferred DNS is: 195.235.113.3
The alternate DNS is: 80.58.32.97
Do I have to put the AirPort Express IP address as 192.168.1.25? And can I use any range of DHCP IP addresses or I must use 192.168.1.x?
Thanks for helping me guys

You need to use NAT in order to share the single IP address.
If you had two (one for the AX and one for your computer) then you wouldn't need to use NAT.
On the Internet Tab use the following.
Connect using Ethernet
Configure Manually
IP address 192.168.1.25
Subnet mask is 255.255.255.0
Router Address 192.168.1.1
DNS 195.235.113.3
80.58.32.97
On the Network Tab
Check Distribute IP addresses
Share a single IP address using DHCP and NAT
I would use 10.0.1.x addressing
On the Airport Tab
Change Wireless Security
Use WPA
Use a password like this
45fs6ue6v1d5fg7d55dsg555
You may need to add the DNS addresses to the clients in order to access the internet.
This may not work, and I would in fact advise talking to your campus network people instead.
iFelix

Similar Messages

How to Connect Airport Express to Existing Wireless Network (Client Mode)

I am posting this for everyone tearing their hair out trying to connect the Airport Express to your own existing home wireless network. After spending 2 hours last night installing this on my father-in-law's home network, I hope to be able to save someone else the agony we went through.
So here's the situation:
Say you already have your own home network set up, and all you want is to be able to use AirTunes to play music off iTunes into your speaker system. And, you don't need the printer sharing capability nor creation of another wireless network (2 of the features of Airport Express). Then this solution is for you - read on.
Unfortunately, Apple's user manual is very unclear how to connect Airport Express to your own network. When you look at the picture diagram they provide, they show Airport Express picking up its signal from another Apple-oriented base. This can make you think you need to buy another piece of hardware to make it work. DON'T If you read through the manual, the Support section here, etc., you will hear lots of talk about "Client Mode" - and that this is the only way to get it to work. Nice - but no one really tells you how to set up the Airport in client mode.
Do yourself a favor, toss that user manual aside and run these steps.
(Note: These directions assume your DSL/Cable Modem is hooked up to a wireless router or acts as its own wireless router)
1. Get a cat5 Ethernet cable (anything but an orange cable - that's a crossover cable) like you would use to connect your PC to your router to pick up the Internet.
2. Connect the Ethernet cable to the router on one end, and to the Airport Express unit on the other end.
3. Plug in your Airport Express unit to the wall (this will not necessarily become its permanent location - you will be able to move it later). The light will glow solid Amber for about 30-45 seconds while it starts up, then blink Amber. At this point, the unit is ready to operate.
4. Install the CD to the PC where your iTunes music is stored. This should be painless. Once you open the program, it should detect the Airport unit.
5. At this point, the on-screen wizard will present you with your options, and walk you through the setup. This is much like the user manual describes - and you should be good to go form here forward.
Some pointers:
- When asked if you want to create a new network, join an existing network, or connect via Ethernet, choose the middle option for joining an existing network. You will need to know the name of your network, the password to connect to the network (if present), and the type of encryption used on the network (e.g. WEP, WPA, etc.). Side note, WPA is recommended, as it is a higher level of security than WEP. You will be able to configure the Airport Express unit to automatically login to your network.
- I would recommend, when creating a password for the Airport Express unit, use the same password as your network, to avoid confusion.
6. The very last step will ask you to save the settings to the Airport Express. Here's the kicker - when you save the settings, you are TRICKING the Airport Express into no longer acting as a network broadcaster, but instead being a "slave" to your own network. What do I mean? You will lose the connection from your PC to the Airport Express - an error message will pop up telling you the unit can no longer be found. While you might think you did something wrong, you actually were successful!
7. Unplug your Airport Express, and disconnect the Ethernet cable from your router and the Airport unit. This will no longer be needed.
8. Go to your desired location where you want to plug in your Airport Express unit. Before plugging it in, connect your Audio cable from the Airport Express to your audio receiver. Once that is connected, then plug in the Airport Express unit. The light will glow solid Amber for 30-45 seconds while it loads, and then will blink Amber for a brief period of time before turning solid GREEN. When this happens, you have successfully connected the Airport Express to your home network!
9. Go back to your PC with iTunes. Open the Airport software - you should now have a listing for your Airport Express unit in the upper left. Click on this, and the wizard will guide you through connecting - you will need the password you created for the unit. You only need to go through this wizard once, and when finished, the software will tell you that can now use iTunes with your Airport unit.
10. Open iTunes. On the lower right, you will see a dropdown for Speakers, and it should be defaulted to My Computer. Click on that drop-down, and you will see the name of your Airport unit. Click on that name, and now your music will broadcast to the Airport unit!
11. Play a song in iTunes. Go to your audio receiver, and connect it to the channel for your external connection to the Airport Express unit. You should hear your music from iTunes. CONGRATULATIONS! =)
I hope these instructions were helpful - I am happy to answer any questions, so feel free to contact me, *******************@*****.**.
<Edited by Moderator>

Thanks for the detailed directions. You are absolutely correct in stating that people should toss the user manual; it's pretty worthless. I have had a problem setting up my new Airport Express as I have described in an earlier post - http://discussions.apple.com/thread.jspa?threadID=1839873&tstart=45
One quick question - does using your setup process set the AE up as part of a distributed network where the AE is acting as a wireless router where it is extending the range of your network? Or, is it simply a wireless connection to your stereo for iTunes? I am interested in having both, since my AE will be at the other end of the house from the main wireless router.
Thanks

How to use Airport Express as a sound output device

Guys,
Is there a way that I can use Airport Express as a sound output device? So, I can play all the sound on my HIFI.
thanks in advance

In order to listen to the non-iTunes audio streams through your Airport Express you will need to use the third party software Airfoil.
http://www.rogueamoeba.com/airfoil/
iFelix

How to use Airport Express to extend range in conjunction with Belkin N Wireless Router

I would like to know how I can extend the range of my Belkin N1 Wireless Router using the the Apple Airport Express? I saw a similar post to this question but the results talk about using this in conjunction with time capsule - I only have a Belkin router and the Airport Express.
If so, can someone help me to find out which settings/configuration I need to set of my Router and Airport Express in order the extend the range of my network.
Thank you in advance for your support.

Thank you for your quick reply. Can you please expand upon how to set up the 'bridge' mode?
I tried connecting the AE via Ethernet from the Belkin router but was not successful in being able to get any additional coverage. I feel like I am missing a vital set of instructions with set-up/configuration details.
Thanks again.

Anyone know how to use airport express to bring internet to a powermac G5 model power PC G5 using airport express?

I bought an airport express and was told that I can configure it, and then move it to the G5 and connect it with the ethernet cable giving the G5 access to the network. But the laptop I first configure it to loses the connection once I remove the ethernet cable between the airport express and the modem. When I connect the G5 to the airport express nothing happens. Any ideas?

Hello Ed,
Is this how you set it up?
http://www.apple.com/airport-express/
Make a New Location, Using network locations in Mac OS X ...
http://support.apple.com/kb/HT2712
10.5, 10.6, 10.7 & 10.8…
System Preferences>Network, top of window>Locations>Edit Locations, little plus icon, give it a name.
10.5.x/10.6.x/10.7.x/10.8.x instructions...
System Preferences>Network, click on the little gear at the bottom next to the + & - icons, (unlock lock first if locked), choose Set Service Order.
The interface that connects to the Internet should be dragged to the top of the list.
10.4 instructions...
Is that Interface dragged to the top of Network>Show:>Network Port Configurations.
If using Wifi/Airport...
Instead of joining your Network from the list, click the WiFi icon at the top, and click join other network. Fill in everything as needed.

Trouble extending WiFi using Airport Express over wired connection

We're attempting to improve the wireless connection in an apartment. The original network runs off a current model Airport Extreme. We used a pair of ZyXEL powerline adapters to extend a wired connection to the other end of the apartment, and connected a new Airport Express at the far end. Airport Utility automatically configured the Express to extend the network. Didn't work so well.
A laptop plugged directly into the powerline adapter gets a great connection. When the Express is connected to the powerline adapter (yes, using the WAN port), not only can I no longer connect to the network wirelessly, but even turning WiFi off and plugging a Cat5 cable into the LAN port on the Express results in a connection that's either nonexistent or so slow as to be nonfunctional. The laptop does pull an IP address when hardwired.
Has anyone had any luck with this type of arrangement?
Thanks!

When you say that AirPort Utility automatically configured the Express to extend the network......you did not specify whether the Express was set up to "extend wirelessly" or "extend using Ethernet".
There is a huge difference here, and if for some reason the Express was first configured to extend the network wirelessly......and then the Ethernet connection was made......that will set up a feedback loop that will effectively crash the network....rendering the Express virtually useless. Sound familiar?
Suggest that you start over and follow our step by step instructions. We assume that you are using a 6.x version of AirPort utility.....or....that you will be using an iPhone or iPad for the setup. Would that be correct? We also assume that you have a spare Ethernet cable on hand......any length will do, the longer the better.
Post back when you are ready to get things set up.

How to use airport express wired and wireless at the same time

Hi,
I currently have FiOS with Verizon, they ran a coax cable to the Verizon router. I didn't ask them to switch to CAT6 cable since I have an airport extreme base station and an airport express base station (both are the newest generation). I ran a CAT6 cable from the Verizon FiOS router to my AEBS (extreme) to make it the default wireless router. The Verizon router and extreme are in one room. Now, the Airport express is in my living. I'd like to extend the wireless network from the extreme. However, I can't seem to find a way to use both wired and wireless from the airport express at the same time. It's now either via wired, or wiresless. So is there a way to get both work?

Can you tell us if you used Apple's instructions for a "roaming" network?
http://support.apple.com/kb/HT4260
Although the instructions picture a 2nd AirPort Extreme in the illustrations, the setup instructions would be exactly the same for an AirPort Express.

How to use airport express as wifi extender?

I have a gateway wifi router from AT&T and I want to extend the wifi range but having problem configuring it. First when I plugged the airport express my Mac's airport utility cannot locate it. Then I decide to hard wire it and my Mac recognized it but it asked for my password when this is my first setup. After resetting airport I managed to bypass the password but now it seems to be picking up another network near by. After changing it to my provider the light on my airport is still blinking and whenever I click on the airport icon on the airport utility it will indicate that the wifi network I have chosen cannot be found and that I should make sure that my main router is plugged. So does anyone who uses AT&T's gateway router has any success in connecting with the express as an extender?

The Amber light is now steady.
The light is green when a device is configured correctly.
The main elements for a roaming configuration are as follows:
o The remote AirPort connects using Ethernet
o Wireless Mode = Create a wireless network
("Extend" is used only with Apple devices when they connnect using wireless only....not Ethernet)
o Wireless network name on the AirPort is the same as the main router
o Wireless Security setting ont the AirPort must match the main router
o Wireless Password on the AirPort must match the main router
o The AirPort must be configured to operate in Bridge Mode

Do i need to use airport express to extend my network to use AirTunes?

I use an AEBS connected to my cable modem and just bought the Airport Express just to be able to stream my iTunes music to a set of powered speakers conncted to it.
When I got into Airport Utility, the only options it provides is to Set up a new network, add to an existing network or replace an existing network.
I just to add to an existing network and it says Airport Express will be used to extend my network.
Now - is that how it's supposed to work? Does it have to extend my network in order to use Air Tunes? The reason I ask is that I remember reading on the forums that extended your network can slow it down....

Bob Timmons wrote:
Version 6.0 will not allow you to configure the Express to "Join a wireless network" if you have another AirPort providing the wireless signal.
If you want the Express to "join" the network, you will need to download and install the much more functional AirPort Utility 5.6 for Mac OS X Lion , which was available on the same day as AirPort Utility 6.0.
Apparently, a number of users missed this.
Suggest that you keep both 5.6 and 6.0 on your Mac and use the one that is most useful.
That is NOT correct.
Version 6.0 will allow you to "Join a wireless network" if you have another Airport providing the wireless signal.
I have an Extreme provinding the wireless network and have 2 Express units Joining the network.
Here is a screen shot of version 6.0 and the Express settings.
You must have missed this in your settings.

Using Airport Express as separate wifi network vs extender with Time Capsule?

Hello all. I recently converted my home computer network from Windows/PC based to an iMac with Time Capsule. On my previous setup, I had a Cisco/Linksys router with wifi, and I also had two Airport Expresses in separate areas of the house where the Linksys had a weak signal. Obviously, I had the Airport Expresses set up as "separate" wifi networks, as they could not be used as network extenders with the Linksys. This setup seemed to work really good, as the 3 wifi networks provided good blanket coverage in all parts of the house. Each network also seemed to "hand-off" to the other pretty well, meaning that Airport Express 1 would show as the active network when you moved far enough away from the Linksys (or insert any of the network names here, even though I'm pretty sure that the device accessing the network has more to do with this than the networks themselves). In particular, the speeds that I got from the Airport Expresses actually eclipsed the speeds that I would get from the Linksys wifi.
My issue is that after I converted everything, I left the Airport Expresses as "separate networks" and essentially removed the Linksys/Cisco router and replaced it with the Time Capsule. So I still have 3 separate wifi networks, just like before, with the Time Capsule network taking the place of the Linksys wifi network. While the Linksys and the Airport Expresses seemed to co-exist together nicely, I get the feeling that the TC and the AEs are somehow working against each other or at least competing with each other for bandwidth. For example, if I have my iPhone right beside my iMac and TC, and I run a speed test on the iPhone using the TC wifi network, I get download and upload speeds in the range that I am expecting (30-40 mbps download). However, when I walk down the hallway to the other end of the house, the TC tends to remain the dominant wifi network, even when I am in the same room with one of the AEs (this is where they used to "hand off" nicely between networks). When you run a speed test in this location still on the TC wifi, the speed drops down to 5-7 mbps, and worse, I believe the signal becomes inconsistent because webpages and data often seem to be freezing in the middle of downloading. I understand that the distance from the TC is causing this, because my solution has been to manually switch from the TC to the closest AE, and that fixes the issue. Run a speed test after I manually switch to the closest AE when I am in the same room as an AE, and the speeds pop back up to 30-40 mbps.
My question is this: would switching the AEs to "extenders" of the TC wifi network help this issue? Honestly, my laziness was one reason that I did not do this when I setup the TC initially, because I have several devices that access the AE wifi networks that I'd have to update with the new network name and password. Everything was working great before, and I just didn't want to upset the apple cart. But if I have created an unfriendly environment between the TC and the two AEs, I certainly have no problem making the change now. I just wasn't sure if making this change would fix my problem or not. I know it's a mundane thing, but I'd like to be able to roam the house without continuously having to manually switch between wifi networks to get a consistent signal.
Sorry if this is a simple issue. I am admittedly a newbie with the TC and its interaction with the AEs.
Thanks in advance!!

It is not a simple issue.
Exactly which method works best is going to take some experimentation.
The way you are trying to set it up as a roaming network is generally considered the best.. but the devices like iphones do not hand off neatly.
It is interesting that they in fact used to hand off better using the Linksys.. which could be due to its poorer range. The new TC having so much better range is causing the phones to not swap "towers" to the local express.
Test it with a Mac laptop.. as generally they do hand off better.
I cannot quite figure out if you are using roaming correctly. All the wireless should have identical names, with identical security setting and passwords.
The only thing that should be different is wireless channels on each item. And you are likely just using auto anyway.
So each device is creating a wireless network. And for 2.4ghz one should be channel 1, then another channel 6 and another channel 11. For 5ghz it will be same idea but there are more channels available.
When you extend wireless, everything runs the same channel. But the wireless speed is reduced. You must disconnect ethernet to each of the expresses.. and the problem is your 30-40mbps will reduce permanently to 15-20mbps for all clients. So take your choice.. 15-20mbps for all clients forced to double hop is better than 5-7mbps which you experience now when you walk around.. although I am not sure how much browsing you do whilst walking. You may need to compromise which is the better out of several not great alternatives.
I would have a test.. which is wrong btw.. but I have heard that it works.
In your roaming network at the present time. Try setting each router to a manual wireless channel.. and fix all of them the same. So for instance, set 2.4ghz to channel 11. Try fixing the 5ghz as well, say the TC is defaulting to 149, it might not actually respond to manual wireless channels.. you will need to test this.. say set to 36 or 40 and see if the TC is actually changed.. if not just set all the expresses to 149 as well. What you are doing is trying to reinforce the wireless in each area.. but this is actually wrong. So all will have same wireless name and same security wpa2 personal is the only valid one.. and all the same password.
Test with a few clients and see if the results give you decent local speeds as well as better roaming.. once you decide which to do, then you will need to change all the clients.

Using Airport Express to Extend my Network

Sorry if this question has been asked before, but I'm getting close to throwing my Airport Express in the Trash.
I have a weak signal downstairs in my house. Upstairs I have an Airport Extreme base station.
So about 2 years ago I bought an Airport Express in the hope that I could simply plug it in downstairs and I would boost my signal strenghth in those areas.
That was two years ago.
Despite my best efforts I have never been able to get this thing to work.
Now a friend at work is telling me that the only way it will work is to tether it to the Airport Extreme with an eithernet cable!!! to me that sounds crazy!!! whats the point?
Can anyone please tell me in a step by step proceadure how I can make this thing fill in my weak coverage downstairs.
I've tried just about everything..
- Connect it to the AE with eithernet cable then try every setting in the airport utility that I can find... still nothing!.. extends, join network etc etc.. nothing!
Thanks for any help,
Steve.

It worked... I used extended but have bought a couple of power line adapters so hopefully will get increased rates.
Strange that I've tried these settings before and no joy. I did a firmware update and a hard reset with a ball pen and it worked. I recon they fixed something!

HT204371 How to setup Airport Express to extend my network range?

I have an Airport Extreme as main router and want to install an Airport Express to extend the range of my wifi. However it only works when connected through an ethernet cable. How can I setup my Airport Express to work wirelessly and extend the wifi range?

I have a Time Capsule in the basement and my daughter is 3 stories up on her iMac and she complains about speed while online. She is about 40 feet up from me with 3 ceilings in between.
It is a nothing short of a miracle that she can get any signal at all under those conditions.
Found an AirPort Express Base Station (the one that looks like a power bar for Apple laptops) - model # is A1084.
Unfortunately, this older version of the Express does not have the capability to "extend a wireless network" using wireless only.
You need the A1264 version, or the "new" AirPort Express (that looks like a miniature Time Capsule) if you want to try to "extend" using wireless only. In this case, you would want to locate the extending device approximately half the distance between the Time Capsule and her computer.
I can't say that this will do a lot to improve things....it's going to be one of those situations where you won't know if it will work until you try.
(or am I better off trying to run a super long Ethernet cable to her somehow?)
This is by far the best choice in terms of performance. There is no signal loss in a wire. She will be amazed at how well and fast her Mac runs this way.

Can I use airport express to extend my network AND stream iTunes???

I have an airport extreme connected to the cable modem and sending a signal out to my home network. I also have a powerbook and an airport express connected to the home stereo.
My question is, can i use the express to extend my extreme signal (to reach the back yard) and stream music from itunes at the same time? The set up utility seems to suggest that you do one or the other.
Thanks!

Are you sure you configured the Express to extend the Extreme's network? If you use the standard setup, the two base stations will be indistinguishable, i.e. you'll only see one entry for the wireless network.
If you were connected to the Extreme when you configured the Express, try turning off Airport in the Airport menu and then turning it back on. The computer should pick up the stronger signal at that point.

Can I use airport express in a wired network to play music through my stereo?

I originally used my 1st gen AE to wirelessly stream music from iTunes on my MacPro to my home theater. This works, but there are some good days and some bad days where there are dropouts in the music. I have recently run Cat6 cable to my HT from my router next to my MacPro. This feeds a Gigabit switch that feeds the ATV, receiver, bluray, HD DVD, etc. I plugged in the AE to the switch but it still defaults to the wifi network rather than taking a feed from the ethernet switch. I know i can (and do) use the ATV (gen 1) to steam music, but sometimes it more convenient to use the AE. Is there a way to force the wifi on the AE off and just have it for streaming from iTunes? Thanks.

Yes, you can configure an AirPort Express Base Station (AX) as a standalone wireless router without Internet access for the purposes of providing a Wi-Fi network for streaming. Note that any computers that will be the host of that stream would need to connect to this AX's wireless network while doing so. They would not be able to be connected to two wireless networks simultaneously for both streaming AND Internet access.

Help! Trying to use Airport Express to extend existing network

Computer Illiterate here. I have an Airport Extreme base station and am connected to the internet. I have been trying to extend my network using an Airport Extreme.
I previously had the network set up like this, but after my DSL line was cut, and going through several decades of customer service **** with Verizon to get everything back again, I can't get it all to work together (friend did it for me the first time and is now unavailable).
The problem is that when I open Airport Setup Assistant, it doesn't recognize either the Airport Express or even the Airport Extreme (which is working and I can connect to the internet). In fact there is nothing in the list at all. Reluctant to reset the Airport Extreme because I will then lose my settings I presume. Will I have to create a new network and password and all the rest of it? Barely managed to do that the first time. Anyone have any ideas about what I'm doing wrong? Would really appreciate any help.

Here is a way to set up a network with more than one router.
http://docs.info.apple.com/article.html?artnum=107454

How to use AirPort Express over a dorm network

Similar Messages

Maybe you are looking for