How to write firmware to ipw2200 serials wireless adaptor?

I have some ipw2200 cards with very low version of firmware, and I'v installed firmware card to my computer.
How to write firmware to the EEPROM of the cards?

Thank you for your patient
With such a low version of fw, the card cannot work in windows.
And I can't dectect the device in wpa_gui. But I can see eth1 by iwconfig, it says the radio is off.

Similar Messages

How to upgrade firmware on 7921g wireless phone from 1.0.2 to 1.0.4 via USB

how to upgrade firmware on 7921g wireless phone from 1.0.2 to 1.0.4 via USB?
The 7921g is connected via USB to a PC. I am using a browser to access the phone. Documentation says "Click the Phone Upgrade hyperlink under SYSTEM options. " but that option is not present or not visible.

You can use the Phone Upgrade area on the web page to upgrade firmware files on the phones by using the USB connection or by using the WLAN. To upgrade the phone software, enter the phone software TAR (firmware file name) or use the Browse button to locate the firmware file on the network.
To display the Phone Upgrade area, access the web page for the phone as described in the Accessing the Configuration Web Page for a Phone section available at http://www.cisco.com/en/US/docs/voice_ip_comm/cuipph/7921g/5_0_1/english/administration/guide/21adm50.pdf

How to write Wireless PC Card Driver?

Hi, All,
Can anyone help me to find out how to write wireless pc card device driver?
Thanks !!

There are [at least] two examples of PCMCIA dirvers in the DDK supplimentary suite. There is also an example of simple DLPI driver.
All you have to do is to combine those examples to get the PCMCIA DLPI driver and fine tune it to match your particular hardware. Any bells ring?
You will definitely need your card programming manual and/or software interface description for the last phase.
If you do not have one, you might get some open source (say, Linux or FreeBSD) driver for your card and do some code analysis to reveal the information you'll need.
Hope this helps...
Ilya.

How can download dvd-writer firmware manually?

Hi,
I have a dm4 1265dx and i wrote wrong the dvd-writer firmware. I need to obtain the hp version of the firmware to ts-u633, but i not found this file on download section. My drive is currently dead, but on bios manager, shows it as internal hard driver. On windows, it isn't detected.
Basically, i want rewrite dvd-writer firmware to appropriate version. I will make it by DOS.

HP does not provide original firmware, only upgrades if they are available for your model, if they are available they will be on the downloads page.
Dell offers a firmware upgrade for the same model

How to save a datas from serial port?

How to save a datas from serial port?

Hi
I need some help about rs-232 communication. I want to make a vi witch can do this things:
-read a txt file (to simulate a serial port like when the datas are coming)
i will get 3 different data in serial port (like this: 121 213 135)
i want to save in a txt file what datas get my vi
so
-write in a txt file or draw in a diagram (or both)
so my problem is: read in serial port and save in a file and draw a diagram.
if anybody can help pls HELP ME because im a beginner in this problem.
I already do something but Im not sure that good.
Thx for all.

How to write XMP changes back to Photoshop DOM in CS SDK?

Hello,
I'm learning to use the ActionScript library for XMP in conjunction with the CS SDK to build Photoshop panels.
I see from the Extension Builder samples that the AssetFragger application demonstrates how to use XMP for annotating comments to image files in Illustrator using com.adobe.illustrator. In the runSet() method the XMP data is manipulated then the changes are stored in the document. So after creating a new XMP node ( XMPArray.newBag() ) it uses doc.XMPString to write the serialized XMP back to the document, then sets doc.saved = false.
        public function runSet():void
            var app:Application = Illustrator.app;
            var doc:Document = app.activeDocument;
            var updateText:String = AssetFraggerModel.getInstance().xmlTextNugget;
             var xmpString : String = doc.XMPString;
            var xmpMeta : XMPMeta = new XMPMeta(xmpString);
            var ns : Namespace = new Namespace(xmpMeta.getNamespace("xmp"));
            xmpMeta.ns::AssetFraggerDescription = XMPArray.newBag();
            xmpMeta.ns::AssetFraggerDescription[1] = updateText;
            var tmp : String = xmpMeta.serialize();
            doc.XMPString = tmp;
            doc.saved = false;
However, using com.adobe.photoshop instead, the XMLString property on the Application activeDocument instance is not available, the doc.saved property is not modifiable (marked as read-only), and the Photoshop Application activeDocument has a xmpMetadata.rawData property available whereas Illustrator did not. The Photoshop activeDocument.xmpMetadata.rawData is marked as read only, so it can be used to get the plain XMP as a string directly, but once modified the XMP cannot be updated in that property. Example:
        public static function traceXMP():void
            var app:Application = Photoshop.app;
            var doc:Document = app.activeDocument;
            var xmpString:String = doc.xmpMetadata.rawData;
            var xmpMeta:XMPMeta = new XMPMeta(xmpString);
            var metaXML:XML = xmpMeta.serializeToXML();
            var Iptc4xmpCore:Namespace = new Namespace(XMPConst.Iptc4xmpCore);
            // demonstrate that a leaf in IPTC can be changed and written to the trace console
            xmpMeta.Iptc4xmpCore::CreatorContactInfo.Iptc4xmpCore::CiUrlWork = 'http://test.com/';
            trace(ObjectUtil.toString(xmpMeta.Iptc4xmpCore::CreatorContactInfo.Iptc4xmpCore::CiUrlWor k.toString()));
            // but now how to write the XMP change back to the Photoshop DOM?
My question is, for a given image file exported as from Lightroom that is rich in custom IPTC metadata, how does one update the metadata in Photosohp via XMP and the CS SDK? I was not able to extract this information from the Advanced Topics: Working with XMP Metadata chapter of the CS SDK documentation
A real, and complete code example would be greatly appreciated over a pseudocode example.
Thank you in advance.
Steven Erat

Ah ha. Found the problem, thanks to Ian. When I saw the inline help appear in Extension Builder for app.activeDocument.xmpMetadata, it indicated that the node as [Read Only], however, the leaf app.activeDocument.xmpMetadata.rawData is in fact not read only. I incorrectly assumed rawData was not writeable when in fact it is.

How to completely turn off Bluetooth and Wireless

Hey everybody,
I'm running Windows XP SP3 via Boot Camp and I was wondering if anyone can assist me in how to completely turn off Bluetooth and Wireless connectivity so that I can reserve as much batter life while being in class taking notes without a plug-in source, but not uninstall. I know there is a Bluetooth control panel and I disabled it there but under "connect to" its still remains there. Basically I want to have the Bluetooth and Wireless turned off completely when I startup and still have the icons shown in the taskbar to let me know that they are still there.
Thanks!

Joergen Thomson, I can see that you have the same thoughts like I do, I wish they could release a software that is stable and better then this.
I dont have the energi or time to report all flaus back to cisco, this product have taking to much of my time and frustration already. Thank you so much for all the time you spend to try get this product stable and hopefully a good product.
I have a costumer that have a webservice that is IP restricted, For now I have to define more then 93 policys openening for the same service because this doesnt handle address list and groups. And all the times I had to set it back to factory default becasue of HTTP Admin server stopped, VPN Problem, Firmware Upgrades, "Packet Loss" and so on takes alot of time becasue I need to reconfig policies back.
For now to they release a firmware is stable I have take this piece off the network and put the back a old Fortinet 60 box.

Does anybody know how to write GUI for J2ME?

Does anybody know how to write GUI for J2ME?
Thanks!

Hi..! I don't know exactly... it's a good question. I refered something. U visit below URL's.
http://www.java-pro.com/upload/free/features/javapro/2000/13iss00/rg0013/rg0013.asp
http://developer.java.sun.com/developer/technicalArticles/wireless/midpui/

How to write the data into EEPROM using Labview?

How to write the data into EEPROM using Labview?

You would need some sort of EEPROM programmer. Typically might
communicate with it via serial. I don't know how you would do this in
LV. You would need to have the command protocol for the programming
device to start with.
Doug De Clue
gpibssx wrote in message news:<[email protected]>...
> How to write the data into EEPROM using Labview?

I dont know how to write an e-mail to HP Support

I dont know how to write an e-mail to HP Support, I stuck on this page and dont know what should i do next.
The following information was returned for your product
Serial number 5*******44
Product number LQ*****#***
Warranty StatusCovered under warranty
Warranty Category Factory Warranty
Warranty End Date 2012-05-27 (YYYY-MM-DD)
The following online support options are available to you
Consumer support forum
Call technical support after you buy (Out-of-warranty customers may pay a fee)
The result displayed is solely based on information available to HP. The legal warranty expiration date is based on the date of purchase as indicated on your receipt. This date might differ from the results shown.
If the displayed result is not correct please contact an HP Technical Support Technician for further assistance.

You are best to use Chat (USA only), or call HP on the phone about warranty concerns, they get too many emails and yours may not get read by the right person.
USA
http://welcome.hp.com/country/us/en/contact_us.html
Everywhere else
http://welcome.hp.com/country/us/en/wwcontact_us.html

I need to install photoshop cs4 extended from a disk to a new computer because my old computer had a hard drive crash. There is no serial number on the back of the case. How can I obtain a usable serial number?

I have to install Photoshop CS4 extended on a new computer from a disk because my old computer had a hard drive crash. There is no serial number on the back of the case. How can I obtain a usable serial number?

Find your serial number quickly
You can activate software without following up and registering it... at least that was the case in the past. The serial number is normally located on the disc case or a box inside the main box. If you did not purchase the disc from Adobe then it is possible you would have dealt with a redemption code, in which case it would have been up to you to keep a record of the serial number, especially if you did not follow up and register the software.

How to write numbers in Arabic?

Hi All,
How to write numbers in arabic?
(how will you in normal papers....assume 123 to be in the arabic numerals here).
Should it be:
| -123|
(or)
| 123-|
Thanks,
Jana

Try the following.
DecimalFormat formatter_ar=null;
Numberformat form = NumberFormat.getNumberInstance(new Locale("ar","EG"));
if(form instanceof DecimalFormat) formatter_ar = (DecimalFormat)form;
String str = formatter_ar.format(-123.45);
System.out.println(str);

How to write a start routine in the trasnformations ?

Hi Experts,
I am working on BI 7, As I want to write a start routine in transformations of 0FIGL_O02 DSO, to allow the GL accounts with cost center data. Already there is a delete statement please find.
*DELETE SOURCE_PACKAGE where BAL_FLAG = 'X'. I had made comment to allow the G/L accounts. since I have some GL Accounts which does'nt have the cost center data, so in this case I have to write a ABAP code to allow this G/L accounts with cost center data.
So Let me know if anyone can help me how to write the ABAP code in the start routine.
Thanks
sekhar

Hi,
            Yopu can write the below lines of code adn try
    SORT source_package BY Receive nr Type ASCENDING.
    DELETE ADJACENT DUPLICATES FROM source_package COMPARING Receive nr Type.
But you should make sure which record of the either rows need to deleted
i.e in
F9001;LU;J001;662;
F9001;LU;J002;662
You need to decide to eliminate 1st or 2nd one.(depends on your requirement)

How to write the start routine in the transformations ?

Hi Experts,
I am working on BI 7, As I want to write a start routine in transformations of 0FIGL_O02 DSO, to allow the GL accounts with cost center data. Already there is a delete statement please find.
*DELETE SOURCE_PACKAGE where BAL_FLAG = 'X'. I had made comment to allow the G/L accounts. since I have some GL Accounts which does'nt have the cost center data, so in this case I have to write a ABAP code to allow this G/L accounts with cost center data.
So Let me know if anyone can help me how to write the ABAP code in the start routine.
Thanks
sekhar

Hi Experts,
I am working on BI 7, As I want to write a start routine in transformations of 0FIGL_O02 DSO, to allow the GL accounts with cost center data. Already there is a delete statement please find.
*DELETE SOURCE_PACKAGE where BAL_FLAG = 'X'. I had made comment to allow the G/L accounts. since I have some GL Accounts which does'nt have the cost center data, so in this case I have to write a ABAP code to allow this G/L accounts with cost center data.
So Let me know if anyone can help me how to write the ABAP code in the start routine.
Thanks
sekhar

How to write a pgm to change the existing encrypted password

Hi all,
can anybody tell me how to write a pgm to change the existing encrypted password.
thanks in advance.

Well, it's going to depend on how it's implemented in the current system.
But basically it's going to look a lot like the current login actions. Presumably you have something that takes the user ID and password, encrypts the password, looks up the encrypted password in the database matching that user ID, and compares them. This functionality would also take a new password (preferably twice so they can be checked for consistency), and if the existing encrypted passwords match, it will encrypt the new password and put it in the database where the old one was.
And if the application has a mechanism for new users to sign up, it'll look a lot like this as well.
But I'm just guessing. This is all going to depend on how the existing functionality is written. Probably the best thing you can do is talk to a programmer at your organization who has worked on the application, and ask them for help.
Hope this helps anyway.

How to write firmware to ipw2200 serials wireless adaptor?

Similar Messages

Maybe you are looking for