Documentation for USRP 1.1 with Ettus N210

Where can I find documentation for using USRP 1.1 with the Ettus N210 device? The documentation that comes with USRP 1.1 has a tiny blurb on the N210 that points to the documentation for NI 292x devices for details. There, I find:
"For Ettus Research devices, use internal names to refer to the internal connectors inside the device case."
I'm trying to understand how to use the API to receive upon the LFRX-LF DC-50 MHz receiver daughter board. The two connectors on that board are labeled "RX-A" and "RX-B", but I can't get those names to work, nor can I get "RF1" or "RF2" to work (the names on the case).
Any suggestions?
Ultimately, I'd like to stream data from both connectors at the same time, if that's possible.

Hi ejubenville,
Support for the LFRX 0-30 MHz daughter board was just added to the NI-USRP driver in version 1.1 and documentation for this daught board is limited. While support for the LFRX is listed, I saw no mention to the LFRX-LF 0-50 MHz daughter board. I expect that your daughter board will work, but if not this may be part of the reason.
As far as the driver is concerned, the Ettus N210 and the NI-292x devices will be configured the same so there is not different documentation for the N210. I would try using RX1 and RX2 which are the names used for the other daughter boards.
Sarah Y
SDR Product Manager
National Instruments | Ettus Research

Similar Messages

Feedback on corporate decision to include documentation for new version together with old

Re:
...That is the intent for the documentation for CS6: that it be in the same document as CS5 and CS5.1...
Every single Adobe executive up the chain of command who is even partially responsible for that astonishing, feeble-minded decision henceforth deserves the unqualifed epithet of idiot.
Waaaay beyond angry!
We know the engineers and developers are not among that group of morons. I'm referencing the Adobe corporate, bureaucratic zombies.
No comment or response is expected as any explanation would be as futile as inherently incredible.

A "What's new" in the front of an old manual does not make a new manual. What it does make is a very unprofessional mess, lacking contents, index, and organization. This is pathetic.

How to write professional documentation for java

Hi, I have few application I need to write documentation for. Im ok with the user and serwer technical stuff. But how to write proper documentation for source code? Any tutorial or howto?
Best regards.

Phenom7 wrote:
Hi, I have few application I need to write documentation for. Im ok with the user and serwer technical stuff. But how to write proper documentation for source code? Any tutorial or howto?A pointer: be explicit and specific when writing Javadocs. If your method never returns null, make sure you say so. If it can't accept null as a parameter, be sure to say what the consequence will be if it happens (but it's OK to say the result is undefined!). A well-written method Javadoc will make users of any API you make a lot more happy, rather than keeping them guessing or making them inspect your source code.
It's expected that while the implementation of a method will change, its pre and post-conditions will not. Therefore, having a good method-level Javadoc is critical to both the people counting on your code and the people maintaining your code.

NI USRP 2921 with Ettus GPSDO Kit

I have connected the "Ettus GPSDO Kit for USRP N200" * with a NI USRP 2921. I have the 1.2 NI USRP driver installed.
In LabVIEW, the "Has GPS disciplines clock?" property is returning false. Are these two devices compatible? And if yes, can LabVIEW's USRP driver gps functions work with this combination?
Many thanks
* FireFly-1A Jackson Labs Tech
PNL 100100-6V FW:0.922 BOM:1.7
SN: 0320112739

Hey Hassan,
The code that you are using should not cause any issues once the GPSDO is installed properly and the EEPROM has been updated. Can you please run uhd_usrp_probe.exe from the command prompt and post the output? The utility is in the same folder I mentioned in my above post. Please also refer to this installation guide to make sure that you have correctly installed the cables for your device:
http://www.ettus.com/content/files/gpsdo-kit_2.pdf
Finally, please confirm that you have manually updated the motherboard EEPROM and power cycled your device. You can update the EEPROM by running the following (in the app note I linked in my last post):
usrp_burn_mb_eeprom --key=gpsdo --val=internal
Sarah Y
SDR Product Manager
National Instruments | Ettus Research

How do I access compacted mail on a Mac version 10.5.8 stuck with Thunderbird version 16.0.2 ? I am unable to access needed documentation for Taxes, etc

How do I access compacted mail on a Mac version 10.5.8 stuck with Thunderbird version 16.0.2 ? I am unable to access needed documentation for Taxes, etc

Where in the world did you read Deleting All My Mail? I have reread my answer several times and cannot seem to find that in there.
When you mark a message for deletion it does just that. It marks it for deletion and hides the message. It is not truly deleted until you compact.
My point is that unless you deleted your important mail they should still be there somewhere.
Your question was about compacting and thinking it put your messages in a nice little box for safe keeping and now you want to open it.
I have to agree that Thunderbird did a horrible job of naming this process because most are like you and do not understand what it actually does. I included the link to the explanation of what compacting means in the Thunderbird world.
Your messages may still be available to your but finding them has nothing to do with compacting.
Thunderbird does not archive anything unless you use that process by selecting the message and pressing a. You have the option to setup where you want that archive to go and what folders to make.
The All Mail folder is a goofy gmail arrangement. If you have problems with that then you need to address that with Google.
If you go into your gmail account on the gmail site do you see the messages you are hunting in the All Mail folder there?

ABAP/4 Keywords for all SAP R/3 Versions with Delta Documentation for abap

Hello Experts,
Do please provide me with the way to find out the Delta Documentations for ABAP for all version of SAP R/3 starting from 3.0 to 6.0
points will be awarded if helpful.
Thanks in Advance

Log on to SAP. Use transaction ABAP_DOCU. Click on Keyword Help. Don't enter an ABAP keyword, press cont. button.
In the window that opens, in the tree on the left handside, you'll see ABAP Changes By Release.
This contains all the information you need.
matt

Integration documentation for sap sd with fico and mm

hi Sappers,
I need Documentation for SAP SD with FICO and MM Module
its very urgent.
mail id : [email protected]

Some basic information :
FI-MM: The integration between FI-MM happens in T-code: OBYC
1. When PO is created :
No Entry -
2. When GR is posted
 Inventory Account dr (Transaction Key BSX in OBYC)
 To GRIR account (T.Key WRX in T-code OBYC)
3. When Invoice is posted
 GRIR account Dr.
 Vendor account Cr.
4. Payment made to Vendor
 Vendor A/c Dr
 To Bank Clearing A/c Cr.
Points to know : Movement Types, Assignment of Movement types to T-keys (T-code OMJJ), Value string (I also need some information on this) , OMWN and OMWB transactions.
There is a close integration b/w FI & MM, actually document flows from MM to FI in the following areas such as,
 1. Movement Types:
Used to enable the system to find the predefined posting rules determining how the accounts of financial accounting system are to be posted & to update the stock fields in the matrl master data.(Goods Receipt, Goods Issue, etc)
 2. Valuation Class:
Assignment of material to grp of gl account, used to determine the gl accounts that are updated as a result of goods movement.
3. Transaction/Event key:
Used to control the storage or filing of documents & assignment of documents.Used to differeniate b/w various transactions such as goods movement tht occur in inventory.
 4. Material Type:
Each material should assign mtrl type in mtrl master record used to update whether changes made in qty are updated in material master record & change in value also updated in stock account.
 FI-SD Integration:
The integration is done in T-code VKOA
 1. Sales Order Created
 -No Entry-
2. PGI done (Goods issue)
 Cost of Goods Sold Dr (Configured in OBYC GBB T-Key)
 To Inventory Account
 3. Billing document released to Accounting
 Customer Account Dr.
 To Sales Revenue Account (ERL T-key in Pricing procedure)
Note : The GL account is assigned to this ERL in VKOA
 4. Payment Received
 Bank Clearing A/c Dr
 Customer A/c Cr.
Points to Know : Good to understand the pricing procedure and how the different transaction keys are used like ERL, ERS etc

SAP documentation for working with BExRepositorySheet?

Can someone point me to where I can find some documentation for programmatically working with the BExRepositorySheet, in particular reading from and writing to the embedded XML script within that sheet.
As I wrote in an earlier thread (BEx 7.0 -- SAPBEXqueries hidden sheet gone -- where is the data stored now?), what I'm trying to do is re-program a very elaborate Excel VBA solution we built for BEx 3.5 to automate the processing of BEx reports by reading the stored variable values in the SAPBEXqueries sheet, but with that sheet gone in BEx 7.0 now, and all that meta-data being stored in BExRepositorySheet XML script instead, I need to be pointed in the right direction as to how to work with the BExRepositorySheet in BEx 7.0.
Thank you kindly for any information.

Hi Stephan,
please see link [http://wiki.sdn.sap.com/wiki/display/VC/WhatisWebAPI|http://wiki.sdn.sap.com/wiki/display/VC/WhatisWebAPI] that contains a reference to a 300+ pages PDF document describing the Web API commands. It is describing the ABAP Web Runtime for BW 3.5 which also exists in BW 7.0.
Best regards
Matthias

Documentation for programming a PXI card with VISA in LabVIEW.

Hi,
Where can I find a documentation for programming a PXI card with VISA in
LabVIEW?
Thanks.
Denys.

Dan,
Thank you for your answer, short but useful to start.
Denys.
"Dan Mondrik" a ecrit dans le message news:
[email protected]..
> Denys:
>
> Our NI-VISA documentation for PXI has been somewhat scarce. We are
> improving it in the next version. In the meantime...
>
> Call VISA Find Resources with "PXI?*INSTR" to find all PXI devices.
> Call VISA Open with a device string like "PXI::devicenum::INSTR" or
> "PXI[bus]::devicenum[::function]::INSTR". In LabVIEW, use the VISA
> class "PXI Instr", available since LV 5.0. (The generic "Instr" will
> also work but will also present GPIB and VXI options and may be too
> confusing.)
>
> The property node has all the available PXI properties such as
> BAR0-BAR5 base/s
ize/type, and also manufacturer ID and model code.
> You can use all the register based in/out/peek/poke methods, just make
> sure to use the appropriate address space for your device.
>
> Dan Mondrik
> Senior Software Engineer, NI-VISA
> National Instruments

1) How to Boot from SAN for T4-1 Server with Solaris 11.1 OS on the disk? 2) How to SMI Label/Format a disk while OS Installation in Solaris 11.1?

FYI....boot from SAN is required for physical server (T4-1) (not OVM).
1) How to Boot from SAN for T4-1 Server with Solaris 11.1 OS on the disk?
The SAN disks allocated are visible in ok prompt. below is the output.
(0) ok show—disks
a) /pci@400/pci@2/pci@0/pci@f/pci@0/usb@0, 2/hub@2/hub@3/storage@2/disk
b) /pci@400/pci@2/pci@0/pci€a/SUNW, ezalxs@0, l/fp@0, 0/disk
e) /pci@400/pci@2/pci@0/pci@a/SUNW, ealxs@0/fp@0, 0/disk
d) /pci@400/pci@2/pci@0/pci@8/SUNW, emlxs@0, l/fp@0, 0/disk
e) /pci@400/pci@2/pci@0/pci@8/SUNW,enlxs@0/fp@0,0/disk
f) /pci@400/pci@2/pci@0/pci@4/scsi@0/disk
g) /pci@400/pci@1/pci@0/pci@4/scsi@0/disk
h) /iscsi—hba/disk
q) NO SELECTION
valid choice: a. . .h, q to quit c
/pci@400/pci@2/pci@0/pci@a/SUNW, ealxs@0/fp@0, 0/disk has been selected.
Type “Y ( Control—Y ) to insert it in the command line.
e.g. ok nvalias mydev “Y
for creating devalias mydev for /pci@400/pci@2/pci@0/pci@a/SUNW,emlxs@0/fp@0,0/disk
(0) ok set—sfs—boot
set—sfs—boot ?
We tried selecting a disk and applying sfs-boot at ok prompt.
Can you please help me providing detailed pre-requesites/steps/procedure to implement this and to start boot from SAN.
2) How to SMI Label/Format a disk while OS Installation in Solaris 11.1?
As we know that ZFS is the default filesystem in Solaris 11.
We have seen in the Oracle documentation that for rpool below are recommended:
- A disk that is intended for a ZFS root pool must be created with an SMI label, not an EFI label.
- Create root pools with slices by using the s* identifier.
- ZFS applies an EFI label when you create a storage pool with whole disks.
- In general, you should create a disk slice with the bulk of disk space in slice 0.
I have seen the solution that using format -e, we change the labelling but all the data will be lost, whats the way to apply a SMI Label/Format on a rpool disks while OS Installation itself.
Please provide me the steps to SMI Label a disk while installaing Solaris 11.1 OS.

Oracle recommends below things on rpool: (thats reason wanted to apply SMI Label)
I have seen in the Oracle documentation that for rpool below are recommended:
- A disk that is intended for a ZFS root pool must be created with an SMI label, not an EFI label.
- Create root pools with slices by using the s* identifier.
- ZFS applies an EFI label when you create a storage pool with whole disks.
- In general, you should create a disk slice with the bulk of disk space in slice 0.

How to check for a function module with its description and functionality

Hi all,
How to check for a function module,with its description and its functionality,in detail how can I know the purpose of a particular function module,how to search for a function module which suits my requirement .

Hi,
You can search a FM of your requirement by putting in the Key words and searching for a FM. Like * KEYWORD * and then pressing F4.
Say for example you need to search something regarding converstion.
Search for * CONVERT * and press F4.
If there is something specfic like converting date to something you can give
DATE * CONVERT *
OR
CONVERT * DATE * and press F4.
Once you narrow down your search you will have a Function module documentation inside the Function module. Please note that all the FMs willl not have documentation.
Regards,
Pramod

How to enable iphone application for multiple iDevices associated with single user for non renewable subscription?

I am developing an ios application which has non renewable subscription.
Which algorithm would be best if the very time an authorized user purchase my application after paying charge for it , can download it for other devices assocated with him for free?
Any help would be appreciated?
    Thanks in advance
     Neeraj@iDev

Thanks! I see a potential problem--iTunes must be open on the main(?) other computer for sharing to works, according to some of the documentation. My situation is that daughter 1 grabs the main computer, access iTunes and her account. Then daughter 2 comes into room, screams upon seeing daughter 1 using the iTunes computer.
I want daughter 2 to calmly walk to computer 2, open iTunes and somehow seamlessly access her iTunes library. In that case, iTunes may be open on computer 1, but not with her library open or her id in force. It might also be the situation that computer 1 does not have iTunes even running at that time, if daughter 1 is on Facebook.
Can Home Sharing handle this situation?
Larry

Goods Issue Documentation for Text (Non-stock) Items

Hi all,
I have a business requirement to provide some form of shipping documentation for text (non-stock) items.
The business do not want to create material masters (NLAGs) for these items as they are different/one off purchases.
The purchase the goods and receipt with account assignment to a cost center or internal order, then sit on the inventory and send it out to customers along with real stock items.
Any ideas on how I can provide some kind of supporting documentation, whether that is a delivery note, or just a simple GI Slip?
Thanks,
Mark.

So they want to purchase items that they don't create materials for/don't get stocked yet want to include those items that don't really 'exist' in SAP on some for of documentation.
If these items go with real Deliveries then why not add them as text items to the Delivery ?

CS5 RAW Could not complete your request because the file appears to be from a camera model which is not supported by the installed version of Camera Raw. Please visit the Camera Raw help documentation for additional information.

I rented a Nikon D600 & D610 and CS5 cannot open the RAW files, i do not have any issued with my D700 RAW files. I am getting this error message -
Could not complete your request because the file appears to be from a camera model which is not supported by the installed version of Camera Raw.
Please visit the Camera Raw help documentation for additional information.
Can anyone please help?

yellowmledbetter wrote:
Sorry, I am on a MAC. I downloaded the link you provided and it's giving the same error message as above. Running CS5.
The error message you gave is from Camera Raw. I thought you said that DNG Converter didn't work?
The link I gave you is an article on getting your raw files to open in Camera Raw. Did you read it? I lazily gave you the link because this is one of the most common problems in this forum, and I get tired of saying the same thing over and over again. I could break it down for your specific case, but I was hoping you could read through the article and work it out for yourself.
But, here goes:
Your cameras are newer than your raw converter, so it won't understand them.
CS5 comes with Camera Raw 6, which can only be upgraded as far as 6.7.1. You can find out which version of Camera Raw you are running in three ways: in the settings title bar (Cmd-K), in the plug-in title bar (press F to start/stop full-screen mode to reveal the title bar), or Photoshop's Help menu (About Plug-ins).
Downloading raw files from newer Nikon cameras with old versions of Nikon Transfer will actually make them unreadable in Adobe software. They can be fixed with a free utility. Again, it's all in the linked article. You should be using up-to-date Nikon Transfer, or Adobe Photodownloader to avoid this problem.
All being well, you have good raw files on your computer. You can convert them to dng using Adobe DNG Converter. IF you are on OSX Leopard or Snow Leopard, you CAN'T use the latest version, because Adobe stopped support. But, if you ARE on a later OSX, you can download DNG Converter 8.6.
DNG Converter is designed to convert FOLDERS of raw files at a time. You select a folder of raw files, and tell it to create DNG copies. BUT, you have to set up the converter before you start using it...
If you load up DNG Converter, you'll notice a button labelled "Change Preferences". Clicking this, you'll see the first option is "Compatibility". Here, you must select the appropriate setting for the version of Camera Raw you HAVE (see above). If you can't work this out, just pick "Camera Raw 5.4 and later". THEN pick a folder of raw files and convert them to DNGs.
All the above is already in the article, but I gave you a personalised response. If you still can't get it to work, please give us more than one sentence. Tell us exactly what you tried, and describe exactly what happened. Which version of OSX you're running, what device and software you downloaded your raw files with, how you used DNG Converter, and so on.
I really should be in bed.

Where can I find Documentation for Oracle financial installation

Hi
Where can I find Documentation for Oracle financial
installation as which all modules to be downloaded for linuk server etc
here is what I have found
===================================
Oracle9i Application Server, Version 1.0.2.2.2 CD Pack for Linux x86 [Act as Server][to be installed on main linux server]
===================================
OracleÂ® Applications 11i Release 9 CD Pack for Linux x86 [Act as client][to be installed on client sean,AJ,Vinod]
===================================
Internet Developer Suite (1.0.2.4.1) CD Pack (with iAS Pack) for Microsoft Windows (32-bit)
===================================

user11872870 wrote:
Hi Tubby,
http://www.quest.com/documents/list.aspx?SearchOff=true&ContentTypeID=20&prod=1
This link has many pdf files but none has the useful information. Those pdf's are just 2 or 3 pages each.Sad Christmas for you then i suppose.
Perhaps you could contact the vendor (quest) and get them to help you in your search for whatever it is you're looking for. An Oracle SQL and PL/SQL forum is not the venue for this, please mark the question as answered, and good luck in your search.

Documentation for USRP 1.1 with Ettus N210

Similar Messages

Maybe you are looking for