HP 1315 ERROR AS I ATTEMPT TO SCAN
The last time I employed my 1315 to scan, it was a couple of months ago. It worked fine.
Today I´ve tried to scan an image and called WIA support inside Adobe Photoshop CS6 Extended.
As I click to scan the following error message pops up : THE SELECTED WIA DEVICE IS NO LONGER AVAILABLE.
If I try to visualize then I get another message :
ERROR DURING VISUALIZATION , IF ANOTHER PROGRAM IS DIGITALIZING WAIT FOR CONCLUSION AND SELECT VISUALIZE AGAIN.
The only thing that changed was the drivers that were updated as suggested by a HP itself.
HP Print and Scan Doctor diagnoses that the driver can´t communicate with device. The power cord was disconected as suggested and windows 8 rebooted.
However the problem persists.
One thing I can say about 1315 : there is not any monotony with 1315 , every time I try to do something a new problem comes up.
Hello there @ron_wolpa , I hope you're well!
I read your post about the issues you are having with your PSC 1315 software and I would like to offer my own suggestions that might help.
Run this tool to uninstall the printer: Microsoft Fix It
Restart the PC.
Perform a Clean Boot and restart the PC again.
Run the HP Printer Install Wizard for Windows to install the printer.
If needed, run the Print and Scan Doctor again to correct any issues.
I hope those steps do the trick for you. Let me know the results
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!
Similar Messages
-
Photosmart C4680 -- Error message when attempting to scan
HELP PLEASE!! -- Have a Photosmart C4680 all-in-one and after 3+ years unable to scan. This began several months ago but recently need to scan items and if I can't fix the printer will need to purchase a new one. The printer works fine, but am unable to print ALIGNMENT copy when I change ink and when I attempt to scan I get the error message:
"The scan cannot be performed because another program has control of the HP imaging device".
As I said I have no problem printing, but am unable to scan either documents or photos. I have done EVERYTHING the FAQ troubleshooting program recommended in the HP Solution Center. I have REBOOTED, UNINSTALLED and REINSTALLED, MOVED USB CABLE TO A DIFFERENT PORT but I still get the same error message. If I can't fix the problem I am tossing this printer as soon as I run out of either Black or Color ink, but I'm definitely NOT getting another HP printer if this is what happens after a couple of years.
Can anyone solve my problem?
THANKS in advance!
HalThanks for providing that information halnyguy.
I would suggest doing a Level 3 uninstall and reinstall the Full Feature Software and start over.
Disconnect the USB cable. If using the USB connection.
Hold down the Windows Logo key () on the keyboard and the 'R' to open the run box, type %temp%.
Delete all files and folders from the temp folder. Choose skip if any pop ups appear saying any of the files could not be deleted.
Download the software and choose to save as, save to desktop. HP Photosmart C4600 All-in-One Printer series Full Feature Software and Driver.
After the software downloads and extracts, open the temp folder again. Close the installation window.
Open the folder starting with 7z. (Example: 7zS2356)
Open folder Util.
Open folder CCC.
If you have an HP computer run the L3uninstall.exe. If you have anon-HP computer run the L4uninstall.exe
When the uninstall has completed restart the computer.
Follow these steps to reset the registry settings and options for Windows Installer.
Hold down the Windows Logo key on the keyboard and the 'R' to open the run box.
In the Open box, type msiexec /unregister, and then click OK.
Hold down the Windows Logo key on the keyboard and the 'R' to open the run box.
In the Open box, type msiexec /regserver, then click OK.
Run the Disk cleanup from Accessories\ System Tool. Delete files using Disk Cleanup.
Download and install the latest version of Adobe flash player. Adobe Flash Player Support Center.
I would disable all the start up programs and temporarily turn off the Antivirus Software to see if that is causing the issue. How to use MSCONFIG . Click on the start up tab and click disable all.
Restart the computer.
Test the printer.
Then you will need to go back in and enable the start up programs and turn the Antivirus Software back on again.
Let me know how you make out.
Thank You.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP -
Could scan all remote servers previously from same sources and version. Replaced/updated all cabs and other files associated (C:\Documents and Settings\<username>\Local Settings\Application Data\Microsoft\MBSA\Cache) with no change. Removed/re-installed
MBSA 2.2 with not effect.
Local scans appear to function fine, but do not wish to download MBSA on EVERY system we need to scan.
Settings for remote scan are: Check for security updates>Configure computers for Microsoft
Update and scanning prerequisites>Advanced Update Services
options:>Scan using
Microsoft Update only
Have attempted from different systems/OS's, with same results. Checked firewall for any blocked traffic from both host and scanner, no entries.
Checked Technet/blogged for about two hours, without any positive results. Please advise/assist.
Regards,
AJ Lebeau
MCSE, MCP, MCP+I, CNA, ACNA, A+
Server Administrator
Progenics Pharmaceuticals
[email protected]
(914) 789-4558Thank you for sending this to the MBSA forums!
If you haven't already, you may want to check the MBSA FAQ located here:
http://technet.microsoft.com/en-us/security/cc184922 specifically under the sections titled, "How can I scan a computer that is protected by a firewall" (to resolve potential DCOM connectivity issues), and "When attempting to scan a remote machine,
why do I see the error 'Cannot deploy security metadata?"
This is also a very misleading error message since the problem could be due to connectivity to the target (client) machines - nothing relating to the CAB file. In any circumstance, you should not need to install MBSA on all of the target machines to
successfully assess their security state.
Possible solutions include
Confirm the latest WUA client is installed on all target machines (with the files you've already placed in the cache directory, you can simply check the scan option to "Configure computers for Microsoft
Update and scanning prerequisites" - which will update and re-register each target machine with the latest WUA client and the ability to respond to requests from MBSA.
Check whether the target machines have limited disk space (unlikely)
Check DCOM settings on both the server - but more likely due to the failure to remotely scan - the target machines.
Change the scan options to further troubleshoot. Specifically, 'Check for security updates' option uses a DCOM connection to the target WUA client while the other scan settings 'Check for weak passwords, etc." use specific UDP/TCP ports as indicated
in the System Requirements section of the MBSA help file and the MBSA FAQ. Also use the 'Advanced Update Services options' to determine whether WSUS connectivity may be at issue.
Please let me know if that helps.
Doug Neal - Microsoft Update and MBSA -
"An internal error has occurred" message when scanning from MX922 to desktop using Windows 7
I am no longer able to scan using my MX922 connected to my desktop running Windows 7 without getting a message on my desktop saying "An internal error has occurred". I have turned the MX922 on and off, I have disconnected both the power cord and USB cable from the MX922 and from my desktop, I have reconnected the USB cable to a different port on my desktop, I have uninstalled all Canon programs from my desktop and reloaded all Canon programs with the MX922 CD, and I have restarted the desktop multiple times. I scan documents several times a week for my business. It has worked fine until today. What do I need to do to correct this problem and get back to scanning?
Hi boisseaujm,
If you temporarily disable any antivirus or firewall software that is on your computer, then attempt to scan again, are you able to scan successfully?
If this is a time-sensitive matter, additional support options are available at Contact Us.
Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well. -
Error messages when trying to scan
When performing / attempting a scan, I get a scan error at the printer,scanner, ( try scan from computer or see documentation, Press okay ) when I attempted to do it from my MacBook Pro ( Mac OS X 10.6.8) I get this error message, ( An Error has occurred). Thanks for your help.
JonHHi JonH52,
Please let me know which model of printer you have. In the meantime, this document might help solve the problem;
Communication Error between the Scanner and Your Computer in Mac OS X v10.4, v10.5, or v10.6
*** If my reply was helpful, please click on the "Kudos Thumbs-Up" on the right, as a way to say "Thanks!".
If this reply also fixed your issue - please click the "Accept as Solution" button, so that others can find the same answer. *** -
Another "An error occurred when attempting to change modules" error
Hello all:
After using Adobe Photoshop Lightroom on Mac OSX trouble free for the past 6 months, I opened up Lightroom today and received the following error: "An error occurred when attempting to change modules." I had not made any changes in between when it worked normally and when the error started to occur. I beleive the last thing I did before this error occurred was to go into the Print Module.
Other information--I keep all my RAW .NEF files on an external Firewire (800) 750 GB drive. This is on Mac OS X 10.5 running Adobe Photoshop Lightroom 1.3 and also with 1.4.1. I'm running an iMac 20" with dual-core 2.2 Ghz Intel processors and 4 GB of RAM. I have around 25k images total.
When I noticed this problem, I was on Lightroom 1.3. I immediately upgraded to 1.4.1, which did not solve the problem. I have also tried many suggestions in the forums including uninstalling the application and removing the .plist file.
I thought I had come up with a solution by creating a new catalog, then importing the former into it. While this seems to work immediately after the import process, as soon as I close it, the problem manifests itself again.
More details that may or (likely) may not help:
- Going to the Develop and Print Modules gives me no problems. However, when I click on Library, Slideshow, or Web, I see the error.
- I upgraded my Mac to the latest patch level after observing this error to no avail.
So it looks like my choices are to create a new file and reimport every single time, or lose all of the work I've done for the past 6 months on thousands of images.
Can anyone please help???? I promise to post the solution when we fix this darn thing so others may benefit. I'd be happy to run through any troubleshooting that y'all would suggest outside of switching to a Canon.
Thanks!!!!
MattI'd first check for the existence of a file ending in .lock, which should be present when LR is in use, but if it exists when LR is quit, it can cause problems, and should be deleted.
Please post back your results. -
I know this is a long story, but I'll be damned if I'm not going to get the most specific help I can (as Apple seems to specialize in assuming user error for all its demonic software). I've never had issues with iTunes before (barring a "Connect to iTunes" snafu with my iPod Touch) -- and never, in fact, with Windows Vista, if you believe that -- but this is the most bizarre thing I've seen.
I recently downloaded the new iTunes v 9.0.3 as I am occasionally prompted to do whenever a new version comes out, and immediately I had problems. Access to the iTunes and Quicktime folders was mysteriously denied after the update, and after several hours of frustration, I was able to grant my own Administrative access to these two folders and installation went through. Thank God.
Then I bought some music. No problems -- downloaded just fine, along with a copy of Cinderella Man and the new episode of Smallville. Life was good for a few days.
Then I connected my iPod Touch to the computer. All of a sudden, Microsoft Windows informs me that the "Apple Mobile Device Service stopped working and was closed," with subtext, "A problem caused the application to stop working correctly. Windows will notify you if a solution is available."
Bullsh*t Windows can help me with anything from Apple.
So I've tried to get iTunes to work with me on this. I've come up against the infamous "iTunes could not connect to this iPhone because an unknown error occurred (OxE8000001)" message. My God, when does it ever end?
So I go into Control Panel > Administrative Tools > Services > Apple Mobile Device and start it back up... only to watch it stop again inexplicably moments later. Hmm... Restart. Stays on. Unplug the iPod and plug it back in. Apple Mobile Device Service stops again. Maybe it's the iPod Service itself. Hey, that one's not started! [Start] "Windows could not start the iPod Service service on Local Computer -- Error 5: Access is denied."
What the f*ck is it with this "Access denied" crap? I've never been denied access to even the most intimate functions, files and folders on my freaking computer before! What has Apple created!?
I thought, perhaps Apple Mobile Device software was somehow removed. Okay, let's redownload iTunes (aka Repair the program from the Programs and Features menu in the Control Panel -- same thing). Huh. "An error occurred while attempting to create directory C:\Program Files\iTunes\CD Configuration," and I can choose to Retry or Cancel. So, instinctively, I deleted the CD Configuration folder, assuming iTunes Setup would just recreate it.
Well, that didn't work now, did it? I deleted it and hit Retry, and it said, "The installer has insufficient priveleges to access the directory: C:\Program Files\iTunes\CD Configuration. Log on as administrator or contact your system administrator." Running the .exe file as an adminstrator changes NOTHING about this predicament.
So that's where it stands. No CD Configuration folder; full access to all files and folders involved; Apple Mobile Device Service still keeps going off for no reason; iPod Service still doesn't run; Repairing/Reinstalling iTunes, Quicktime, Bonjour, etc. does nothing; and God (aka Steve Jobs, apparently) hates me.
. . . . . . . . . . . . Help me.Hi there,
I would recommend taking a look at the troubleshooting steps found in the article below.
Trouble installing iTunes or QuickTime for Windows
http://support.apple.com/kb/ht1926
-Griff W. -
ITUNES WILL NOT DELETE FROM ADD @ REMOVE PROGRAMS,
MESSAGE, READS a network error occured while attempting to read from the file C:WINDOWS\installer\iTunes.msiAll sorted now just needed to repair itunes from control panel
-
I have Lightroom 5 installed on my iMac which I downloaded (uploaded?) to my MacBook Air (via wi-fi) but unlike the iMac, I'm unable to use the program on the MacBook Air. When I open the program on the iMac and click 'file', (as people using the program would know) there are 21 options - import pics, export, etc, etc - however, in the version on the MacBook Air, opening 'file' gives me four options - New Catalogue, Open Catalogue, Page Setup and Printer - and with that comes the pop-up message "An error occurred when attempting to change modules". Any ideas please?
A forum thread from 3 years ago talking about LR 1.x which had this problem seems to need permissions fixed or new folders created with the corrected permissions. You might try doing a repair permissions for your user and/or run LR as an administrator user. I am a PC person so cannot tell you exactly how to do that.
https://forums.adobe.com/message/1457020 -
I updated itunes to 10.4, my ipod touch was wiped clean then errored (2003) when attempting to restore. Now my ipod is clear, when I turn it on I get the "Connect to itunes screen", this never goes. I have tried disabling my antivirus, to allow me to restore with no luck.
When I go into itunes I get the message - itunes has detected an ipod in recovery mode. You must restore this ipod before it can be used with itunes,
how am I supposed to do this ?
I would rather take the ipod to someone to do the restoration - I still have itunes with all of my downloads on my computer, I dont want to risk losing this as I can re-install onto my ipod when it is sorted.Error 2000-2009 (2001, 2002, 2005, 2006, 2009, and so on): If you experience this issue on a Mac, disconnect third-party devices, hubs, spare cables, displays, reset the SMC, and then try to restore. If you are using a Windows computer, remove all USB devices and spare cables other than your keyboard, mouse, and the device, restart the computer, and try to restore. If that does not resolve the issue, try the USB issue-resolution steps and articles listed for Error 1604 above. If the issue persists, it may be related to conflicting security software.
Above from:
http://support.apple.com/kb/TS3694
It may be more than you security software.
Do you have access to another computer you can use to restore the iPod to factory defaults/new iPod? -
I have a web page that contains a ReportViewer control. I am trying to display a report, which is an .rdl file located on the SSRS server, in this ReportViewer control. I have set the ReportPath and ReportServerUrl correctly. I am
getting an error message.
Am I suppose to use an .rdlc file rather than a .rdl file? Does the web server configuration need to use a certain account?
I am getting the following error message:
The attempt to connect to the report server failed. Check your connection information and that the report server is a compatible version.
The request failed with HTTP status 404: Not Found.Hi bucaroov,
The error "The request failed with HTTP status 404: Not Found." means the ReportServerURL configured in the ReportViewer control is invalid.
Please follow these steps to solve the issue:
Logon the Report Server machine.
Open the Reporting Services Configuration Manager.
Copy the Report Server URL from 'Web Services URL'.
Logon the application server(in this case, it is the server that host the web page), check if we can use the URL we got from step 3 to access the Report Server. If so, please replace the ReportServerURL in the ReportViewer control with this URL. If it is
not available, could you please post the error message.
Additionaly, we don't need to provide the extension for a server report. The ReportPath should be like: /<reports folder>/<report name>
For more information, please see:
Walkthrough: Using the ReportViewer Control in Remote Mode:
http://msdn.microsoft.com/en-us/library/ms251669(VS.80).aspx
If you have any more questions, please feel free to ask.
Thanks,
Jin Chen
Jin Chen - MSFT -
Error during last attempt to refresh cache in tranaction sxi_cache
Dear Team,
We are geting below error , while executing sxi_cache transaction . please suggest .
Status of Runtime Cache.
Cache content is up-to-date
Error during last attempt to refresh cache , wile double clicking this , we found below log .
Thrown:
com.sap.aii.ib.server.abapcache.CacheRefreshException: Attempt to access application REPOSITORY using HTTP Method Invocation (HMI) failed. Detailed information: Invoking ROA method "ReadObjects" via HMI ... FAILED due to following exception: Message: Connection to system REPOSITORY using application REPOSITORY lost. Detailed information: Error accessing "http://gsapnppid.galsap.local:50000/rep/remoteobjectaccess/int?container=ejb" with user "PIDIRUSER". Response code is 401, response message is "Unauthorized"
Stacktrace:
com.sap.aii.utilxi.hmi.api.HmiCoreException: Connection to system REPOSITORY using application REPOSITORY lost. Detailed information: Error accessing "http://gsapnppid.galsap.local:50000/rep/remoteobjectaccess/int?container=ejb" with user "PIDIRUSER". Response code is 401, response message is "Unauthorized"
at com.sap.aii.utilxi.hmi.api.HmiCoreException.newCommunicationError(HmiCoreException.java:85)
Kindly AdvisePlease Check if the user PIDIRUSER is locked.
If user is not locked, check if the credential for user PIDIRUSER and respective password is correctly maintained in Exchange Profile.
Regards,
Murali Narayanan -
An error occurred while attempting to perform the operation.
Hi All,
I am getting an error while running the report:
"An error occurred while attempting to perform the operation. Then operation did not complete successfully."
Although I can see the data coming is correct, but don't know why this error is coming.
I have seen for NULL values.
How can I see the detail log to trace the error?
Please help.
Thanks,
Himanshu TiwariHi,
You can login as system using SQLPlus and use the DBMS_SYSTEM.set_sql_trace_in_session procedure to set trace on another Discoverer session. This should establish if there is any database error occuring in the Discoverer session.
Rod West -
Need help getting around the following error: JBO-27101: Attempt to access dead entity in EO.
Hi everyone,
My logic in prepareForDML() updates some attributes (shown in the snippet below) based on whether an insert or update is taking place. But, when I delete a line, I get the following error: JBO-27101: Attempt to access dead entity in EO. So far, I have not been able to catch this error.
if (operation == DML_INSERT) {
setLineId((new SequenceImpl("eo_s",
getDBTransaction()).getSequenceNumber()));
setCreatedBy(createdBy);
setCreationDate(currentDateAndTime);
setLastUpdatedBy(lastUpdatedBy);
setLastUpdateDate(currentDateAndTime);
} else if (operation == DML_UPDATE) {
setLastUpdatedBy(lastUpdatedBy);
setLastUpdateDate(currentDateAndTime);
Any advice would be appreciated. Thanks!
JamesHi Timo,
Thanks for responding. Whenever I delete a line and commit, I get the error. And, since inserts and updates are all that I am interested in, I did not think that I needed deletion logic. The VO contains several EOs, but all are reference EOs that cannot be updated except for the main EO.
Here is the entire prepareForDML() method:
protected void prepareForDML(int operation, TransactionEvent e) {
// BEGIN Initial Version
// Using prepareForDML is a best practice (versus doDML).
ApplicationModule am;
boolean lineIsValid;
byte entityState;
byte postState;
Date currentDateAndTime;
Date weekEndingDate;
Number createdBy;
Number lastUpdatedBy;
String amConfiguration;
String amDefinition;
String entityStateText;
String operationText;
String postStateText;
ServicesAMImpl servicesAMImpl;
Timestamp timeStamp;
// amDefinition = "com.model.services.ServicesAM";
// amConfiguration = "ServicesAMLocal";
// am = Configuration.createRootApplicationModule(amDefinition, amConfiguration);
createdBy = new Number(-1); // TODO fnd_profile.value('USERNAME')
entityState = getEntityState();
entityStateText = null;
operationText = null;
postState = getPostState();
postStateText = null;
lastUpdatedBy =
new Number(-1); // TODO fnd_profile.value('USERNAME'); is there a last login id?
// servicesAMImpl = (ServicesAMImpl)am;
// lineIsValid = servicesAMImpl.callValidateLineProcedure(getBillable());
timeStamp = new Timestamp(System.currentTimeMillis());
currentDateAndTime = new Date(timeStamp);
// TODO Should weekEndingDate be in the callValidateLineProcedure()?
weekEndingDate =
commonCode.nextDay(getActivityDate(), Calendar.THURSDAY);
setWeekEndingDate(weekEndingDate);
// TODO See https://community.oracle.com/message/9542286?tstart=14.
// if (entityState != Entity.STATUS_DELETED & entityState != Entity.STATUS_DEAD)...
System.err.println("prepareForDML - getLineId: " + getLineId());
switch (operation) {
case DML_DELETE:
operationText = "Delete";
break;
case DML_INSERT:
operationText = "Insert";
break;
case DML_UPDATE:
operationText = "Update";
break;
System.err.println("prepareForDML - operationText: " +
operationText); // TODO
// System.out.println("prepareForDML - operationText: " + operationText); // TODO
switch (entityState) {
case Entity.STATUS_INITIALIZED:
entityStateText = "Initialized";
break;
// Don't do anything.
case Entity.STATUS_UNMODIFIED:
entityStateText = "Un-Modified";
break;
// Don't do anything.
case Entity.STATUS_DEAD:
entityStateText = "Dead";
break;
// Don't do anything.
case Entity.STATUS_DELETED:
entityStateText = "Deleted";
break;
// entity.revert();
// entity.refresh(Entity.REFRESH_CONTAINEES);
case Entity.STATUS_MODIFIED:
entityStateText = "Modified";
break;
// entity.refresh(Entity.REFRESH_UNDO_CHANGES);
case Entity.STATUS_NEW:
entityStateText = "New";
break;
// entity.refresh(Entity.REFRESH_FORGET_NEW_ROWS);
// entity.refresh(Entity.REFRESH_REMOVE_NEW_ROWS);
default:
entityStateText = String.valueOf(entityState);
System.err.println("prepareForDML - entityStateText: " +
entityStateText);
switch (postState) {
case Entity.STATUS_INITIALIZED:
postStateText = "Initialized";
break;
// Don't do anything.
case Entity.STATUS_UNMODIFIED:
postStateText = "Un-Modified";
break;
// Don't do anything.
case Entity.STATUS_DEAD:
postStateText = "Dead";
break;
// Don't do anything.
case Entity.STATUS_DELETED:
postStateText = "Deleted";
break;
// entity.revert();
// entity.refresh(Entity.REFRESH_CONTAINEES);
case Entity.STATUS_MODIFIED:
postStateText = "Modified";
break;
// entity.refresh(Entity.REFRESH_UNDO_CHANGES);
case Entity.STATUS_NEW:
postStateText = "New";
break;
// entity.refresh(Entity.REFRESH_FORGET_NEW_ROWS);
// entity.refresh(Entity.REFRESH_REMOVE_NEW_ROWS);
default:
postStateText = String.valueOf(postState);
System.err.println("prepareForDML - postStateText: " + postStateText);
// DeadEntityAccessException
if (operation == DML_INSERT) {
setLineId((new SequenceImpl("eo_s",
getDBTransaction()).getSequenceNumber()));
setCreatedBy(createdBy);
setCreationDate(currentDateAndTime);
setLastUpdatedBy(lastUpdatedBy);
setLastUpdateDate(currentDateAndTime);
} else if (operation == DML_UPDATE) {
setLastUpdatedBy(lastUpdatedBy);
setLastUpdateDate(currentDateAndTime);
// Configuration.releaseRootApplicationModule(am, true);
// END Initial Version
super.prepareForDML(operation, e);
Here is the entire doDML() method:
protected void doDML(int operation, TransactionEvent e) {
// BEGIN Initial Version
// This logic is for troubleshooting only.
String operationText;
operationText = null;
switch (operation) {
case DML_DELETE:
operationText = "Delete";
break;
case DML_INSERT:
operationText = "Insert";
break;
case DML_UPDATE:
operationText = "Update";
break;
System.err.println("doDML - operationText: " + operationText); // TODO
// System.out.println("doDML - operationText: " + operationText); // TODO
// END Initial Version
super.doDML(operation, e);
James -
Error message: "The attempt to burn a disc failed. An unknown error"
Anyone having this error message after attempting to burn a disc?
I have 6 discs sitting here ruined after this happened consistently.
Called Apple tech support. Said they never heard of this.
What can I do to resolve? Tried doing the iTunes update and that does not appear to have helped. I am beyond frustrated. To not be able to burn all my purchased music to cd's is not making me a happy camper.
Anyone have any ideas how to fix?
Thanks for all suggestions..Hey guys, having same type of problem and figured I would throw in my 2 cents. I was getting "error 4000"; i Googled that and followed the procedures for going to my control panel, add/remove and clicking repair. I tried a burn again, also paying attention to previous notes and lowered my write speed to 8X. Same error, different number, this time 4261. I found this thread so I decided to paste my info too, but i do notice the last line of code reads "speed 10X". Hope this helps? I have burned plenty of CDs before, I am burning a mix of MP3 and MP4, amazon and apple purchased, and using older memorex CD-R. They say "recordable, 52X, 700mb, 80 min" at the top. Hope it helps and thanks for the time and effort on here!
Microsoft Windows 7 x64 Home Premium Edition (Build 7600)
Dell Inc. Inspiron 1464
iTunes 10.0.1.22
QuickTime 7.6.8
FairPlay 1.9.16
Apple Application Support 1.3.2
iPod Updater Library 10.0d2
CD Driver 2.2.0.1
CD Driver DLL 2.1.1.1
Apple Mobile Device 3.2.0.47
Apple Mobile Device Driver 1.49.0.0
Bonjour 2.0.3.0 (214.3)
Gracenote SDK 1.7.1.420
Gracenote MusicID 1.7.1.78
Gracenote Submit 1.7.1.106
iTunes Serial Number A13F95689B6E935E
Current user is an administrator.
The current local date and time is 2011-03-18 21:25:19.
iTunes is not running in safe mode.
WebKit accelerated compositing is enabled.
HDCP is supported.
Video Display Information
Intel Corporation, Intel(R) HD Graphics
** External Plug-ins Information **
No external plug-ins installed.
iPodService 10.0.1.22 is currently running.
iTunesHelper 10.0.1.22 is currently running.
Apple Mobile Device service 3.2.0.0 is currently running.
** CD/DVD Drive Tests **
LowerFilters: PxHlpa64 (2.0.0.0),
UpperFilters: GEARAspiWDM (2.2.0.1),
E: HL-DT-ST DVD+-RW GT30N, Rev A101
Audio CD in drive.
Found 15 songs on CD, playing time 69:43 on Audio CD.
Track 1, start time 00:02:00
Track 2, start time 03:28:41
Track 3, start time 07:28:54
Track 4, start time 11:36:32
Track 5, start time 15:58:57
Track 6, start time 20:26:51
Track 7, start time 25:01:74
Track 8, start time 29:43:02
Track 9, start time 34:25:65
Track 10, start time 39:19:72
Track 11, start time 44:14:37
Track 12, start time 49:13:50
Track 13, start time 54:14:42
Track 14, start time 59:16:04
Track 15, start time 64:17:54
Audio CD reading succeeded.
Get drive speed succeeded.
The drive CDR speeds are: 10 16 24.
The drive CDRW speeds are: 10.
The drive DVDR speeds are: 10.
The drive DVDRW speeds are: 10.
Force Optical Power Calibration before burn is turned on in the preferences.
The last failed audio CD burn had error code 4261(0x000010a5). It happened on drive E: HL-DT-ST DVD+-RW GT30N on CDR media at speed 10X.
Maybe you are looking for
-
Server Admin Graphing No Longer Works in 10.4.6
Has anyone else noticed that the graphing functions no longer work in 10.4.6? I have also noticed that the CPU % Usage in the System - Hardware displays 62% no matter that the system is idle. This only appears on my single processor G4 not my Dual G4
-
How come my scans are being saved as pdf files, I want them saved as JPEG or JPG
I am a member of ancestry.com and need to upload my photos into my ancestry program, however, when I scan a photo, it automatically is generated as a PDF and I cannot upload it. Can you tell me what to do to get my scanned docs to save as a JPG file?
-
IPhone alarm clock via speakers
Hey, I wanted to ask if the sound of my iPhone alarm clock is transmitted to speakers while it's connected with the Apple Universal Dock. I tried it with a 3.5mm wire but no sound was transmitted. Does anybody have some experience with the iPhone ala
-
Multi-language support for change password page in OAM
How do we setup multiple language change password from lost password management in OAM. Thanks. Vinay
-
Cant get iMovie08 to show all photos that are in iphoto.
Can't get iMovie08 to show all photos that are in iphoto. only shows about 30, when there are actually about 60 or so in one album. any ideals?