HP Pavilian m7050y & Monitor HP vs 19c keeps crashing after installing windows 7

Question

Hi Forum Experts, hope all is well.  Hopefully someone will be able to help me with this problem.  
My HP Pavilian m7050y & Monitor HP vs 19c keeps crashing after installing windows 7.   
I knew there was a problem when I first installed windows, because the windows logo was not centered on the monitor after intial startups.  I did adjust it a little by pressing auto/select on my monitor, and that helped with the centering a bit but it is not perfectly centered. 
The screen goes blue and this is the message I get when it crashes and restarts.
    Problem has been detected and windows has been shut down to prevent damage
to your computer.
attempt to reset the display driver and recover from timeout failed.
if this is the first time you've seen this stop error screen,
restart your computer, if this screen appears again, follow
these steps:
Check to make sure any new hardware or software is properly installed.
If this is a new installation, ask your hardware or software manufacturer
for any windows updates you might need.
If problems continue, disable or remove any newly installed hardware
or software.  Disable BIOS memory options such as caching or shadowing.
If you need to use safe mode to remove or disable components, restart
your computer, press F8 to select Advanced Startup Options, and then
select safe mode.
Technical Information
*** STOP: OX00000116 (0X85E75330, 0X9303C5BC, OX00000000, 0X00000002)
*** atikmdag.sys - Address 9303C5BC base at 9302C000, DateStamp 49f1996c
Collecting data for crash dump ...
Initializing disk for crash dump ...
Beginning dump of physical memory.
Dumping physical memory to disk: 
the message is also slightly of to the left it really reads like this.
Problem has been detected and windows has been shut down to prevent damage
o your computer.
ttempt to reset the display driver and recover from timeout failed.
f this is the first time you've seen this stop error screen,
estart your computer, if this screen appears again, follow
hese steps:
heck to make sure any new hardware or software is properly installed.
f this is a new installation, ask your hardware or software manufacturer
or any windows updates you might need.
f problems continue, disable or remove any newly installed hardware
r software.  Disable BIOS memory options such as caching or shadowing.
f you need to use safe mode to remove or disable components, restart
our computer, press F8 to select Advanced Startup Options, and then
elect safe mode.
echnical Information
** STOP: OX00000116 (0X85E75330, 0X9303C5BC, OX00000000, 0X00000002)
** atikmdag.sys - Address 9303C5BC base at 9302C000, DateStamp 49f1996c
ollecting data for crash dump ...
nitializing disk for crash dump ...
eginning dump of physical memory.
umping physical memory to disk: 
Once windows is fully rebooted all pages, and the display look ok, until it crashes again.   I searched for updated drivers on the HP and Windows site but could not find any.  The one that is currently installed is called (Generic Pnp Monitor).
Thanks in advance for your expert advice.
Juan.

Answer 1

Thank you for the additional information.
Did you run the Win 7 Upgrade Advisor to assure that your computer is compatible?  There may be a problem with compatibility.  Also, which version of Win 7 are you running; 32-bit or 64-bit?
Signature:
HP TouchPad - 1.2 GHz; 1 GB memory; 32 GB storage; WebOS/CyanogenMod 11(Kit Kat)
HP 10 Plus; Android-Kit Kat; 1.0 GHz Allwinner A31 ARM Cortex A7 Quad Core Processor ; 2GB RAM Memory Long: 2 GB DDR3L SDRAM (1600MHz); 16GB disable eMMC 16GB v4.51
HP Omen; i7-4710QH; 8 GB memory; 256 GB San Disk SSD; Win 8.1
HP Photosmart 7520 AIO
++++++++++++++++++
**Click the Thumbs Up+ to say 'Thanks' and the 'Accept as Solution' if I have solved your problem.**
Intelligence is God given; Wisdom is the sum of our mistakes!
I am not an HP employee.