HP Pavilion dv6 7039tx Notebook-It was working fine and then it suddenly got stuck during startup.

I own a HP Pavilion dv6 7039tx Notebook. The OS is Win 7 64bit. I made 4 partitions after formatting the 1TB HDD as the C drive would not reduce to the 40GB size I wanted through disk management.
It was working fine till now and then it suddenly got stuck during startup.
I talked to customer support and they said it was a OS problem and I should order a set of 6 Recovery DVDs. i want to know if using the HP recovery disk
1) Has an option to repair the system and leaves the disk partition unchanged?
2) It resets the notebook to factory condition?
3) There is an option of recovery disk which I should specifically ask for?
Thanks!!

Hi RanSri,
I understand you are having issues with the HP Pavilion dv6 7039tx Notebook.
You can restore it to a previous time when it was working correctly.
This link for windows working correctly.
http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&dlc=en&docname=c01835735&lc=en&product=5277768&tmp...
Use this link if Windows does not open normally.
http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&dlc=en&docname=c01835735&lc=en&product=5277768&tmp...
Hope this helps.
Thanks.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom to say “Thanks” for helping!

Similar Messages

I went to update my ipod touch and restore it. it was working fine and then when it it restarted itself it it stuck onone scren te same one when u first get it, it will not do anythig elts what do i do please help

i went to update my ipod touch and restore it. it was working fine and then when it it restarted itself it it stuck onone scren te same one when u first get it, it will not do anythig elts what do i do please help i whont my ipod touch back

Restore loop (being prompted to restore again after a restore successfully completes): This issue is typically caused by out-of-date or incorrectly configured third-party security software. Please followTroubleshooting security software issues if USB troubleshooting does not resolve this issue.
Error 13 and 14: These errors are typically resolved by performing one or more of the steps listed below:
Perform USB isolation troubleshooting, including trying a different USB port directly on the computer. See the advanced steps below for USB troubleshooting.
Put a USB 2.0 hub between the device and the computer.
Try a different USB 30-pin dock-connector cable.
Eliminate third-party security software conflicts.
There may be third-party software installed that modifies your default packet size in Windows by inserting one or more TcpWindowSize entries into your registry. Your default packet size being set incorrectly can cause this error. Contact the manufacturer of the software that installed the packet-size modification for assistance. Or, follow this article by Microsoft: How to reset Internet Protocol (TCP/IP) to reset the packet size back to the default for Windows.
Connect your computer directly to your Internet source, bypassing any routers, hubs, or switches. You may need to restart your computer and modem to get online.
Try to restore from another known-good computer and network.
Error 50: This error (and error -50) are timeout errors. Follow the steps for errors 13 or 14 above.
Above from:
http://support.apple.com/kb/TS3694

HT1430 Connection to the server failed. Was working fine and then just stopped. Done everything the forums suggest.

My mail keeps coming up with "connection to server available". Was working fine then suddenly stopped. I performed the ISO 6.0.1 update afterwards hoping it wild fix it but it didn't. Have followed all the instructions on other forums ie turning phone off, deleting account and reactivating, even logged out of hotmail at home . Nothing has worked. Please help, I need my emails for work.

iOS: Unable to send or receive email
http://support.apple.com/kb/TS3899
Can’t Send Emails on iPad – Troubleshooting Steps
http://ipadhelp.com/ipad-help/ipad-cant-send-emails-troubleshooting-steps/
Setting up and troubleshooting Mail
http://www.apple.com/support/ipad/assistant/mail/
iPad Mail
http://www.apple.com/support/ipad/mail/
Try this first - Reset the iPad by holding down on the Sleep and Home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons. (This is equivalent to rebooting your computer.)
Or this - Delete the account in Mail and then set it up again. Settings->Mail, Contacts, Calendars -> Accounts Tap on the Account, then on the red button that says Remove Account.
 Cheers, Tom

Firefox no longer launches when I click the launch icon. It was working fine and then all of a sudden it won't launch. I have Vista home prremuim service pack 2. Can you please help me resolve this issue so I can once again use firefox? Thanks

firefox was working. Now it is not. Won't launch when I click the icon. Don't know the version as I cannot get it to launch to check the version.

https://support.mozilla.com/en-US/questions/891374
http://kb.mozillazine.org/Browser_will_not_start_up

HT1476 my charger was working fine and then it just stopped

My iphone was charging and then when i looked at my phone it said this charging is not supported with this accessory. When i plugged it into my macbook it still recgonized the phone but wont charge. Why is it all of a sudden not working. the cord isnt bent or damaged and it was working just fine.

Try another cable, it could just be that now that cable is faulty.

Epson WF-3521 printer was working fine and then suddenly stopped

Printer has been working fine since we bought it but tonight I suddenly began receiving an error message stating that the printer is offline. I have turned both off and on checked to ensure they are both on the correct router, but then problem persists.

Here's a relatively easy way to make sure the printer has the latest firmware, which may well solve your issue:
There is a free app in the App Store called Epson iPrint. Download and install it on your iPad, then open it, and see if it sees your printer. If so, click Maintenance in the lower left, and then click Printer Settings on the bottom. Then click Firmware Update. It will detect if your printer has the latest firmware and install it if not.
Hopefully that will fix your issue.

Was working fine and then....

Ok, my mac was fine yesterday.
I have an Imac 20" inch 2 gb of ram...
I had shut it down, and I turned it back on. It came up but started running sluggishly. So It ended up freezing, so i held the power button down. Now it's stuck at the apple white screen with the little spinning thing. I have logged in via single user mode, and tried to run fsck -fy... It gets to checking catalog file... and sits... then an error comes up....
Failed to issue COM RESET successfully after 3 attempts. Failing...
then
AppleAHCIDiskQueueManager::setPowerState(0x4079c00, 2 -> 1) timed out after 190049
I don't know what to do. I just need to know if its the hard drive took a crap or something more serious... or if something simple... I don't have a retail cd but I am trying to find one...
I have boot camp installed, and windows booted up once... Ran fine for a little then kinda froze... so i'm not sure... Is there something i can do if i can get the windows side running? Please help me out as I have no idea where to look up error codes...
I also tried target mode from my powerbook to my imac... and it just kinda freezes when I try to look at the volume..... anything... Please help...
Thanks in advance,
Samuel

well mine was a bad hard drive... that was the problem... Now whether or not an update can cause a hard drive to fail.... not sure.... But i bought a new 500gb hd off of newegg it was only $60... so not too bad... Taking apart the mac sucked though... hahahaha.... get a suction cup... and lift the screen... i broke my hd temp sensor though... so the fan was running at like 5000 rpm.... i got fancontrol and went to the terminal and found out the correct command to set the hd fan to MAX speed of 3500...
/Applications/smcFanControl.app/Contents/Resources/smc -k F1Mx -w 3e80
everything is working good now...

TS4006 All of my devices suddenly say "offline" even though I know they are on. It was working fine and then it stopped working for all 4 devices. What's up?

All my devices have stopped working. Everthing says offline even though I know they are on and functioning.

Sounds like you have corrupt backup data, if this occurs from one phone to another. Try restoring the phone as a new device, without a backup. Try using for a day before installing any other apps, etc. See if that improves the battery life. Then try syncing back applications a couple at a time. Something seems to be locking in the processor which is draining the battery.
Do you live in an area where there are Apple Stores? If so, try making an appointment with the Genius Bar to have the device checked out.

HT201210 my Iphone was working fine and then I plugged it into Itunes for the update and now it says I have to restore to orignal factory settings. I will lose my contacts, photos and anything else I have loaded over the past two years. REALLY?? WHY

This is so frustrating! I plugged my Iphone 4S into my computer to update it via Itunes and now it says I have to restore to factory settings and will lose all of my contacts, photos, and applications I have downloaded. All I was really wanted to do was delete photos that uploaded from my home computer and took up all the space on my phone! GRRRR I hate this

If you are using the iphone as designed then you should lose very little or nothing.
You should be syncing contacts with your computer regularly, so all of your contacts should be on your computer and you can sync them back.
You should be importing all pics taken with the iphone to your computer regularly as you would with any digital camera, most especially before any attempt to update.
You should be transferring all purchases made on your iphone to your computer: File>Devices>Transfer Purchases
You can redownload some itunes purchases in some countries:
Downloading past purchases from the App Store, iBookstore, and iTunes Store

How do I get the function browser to appear when I types an = sign in a cell-The fn browser was working OK and then quit appearing---

How do I get the function browser to appear when I type an = sign in a cell-The fn browser was working OK and then quit appearing---

I just stumbled onto the answer---The format sidebar must be selected before the function sidebar will appear--Did not see this in the help section--maybe just overlooked it--

I am using iphone 3gs since last 4 days. Till yesterday night it was working fine and i have connected this phone for charging . Morning there was apple logo in the screen and every 1mte (approx) it is blinking. I could not restart the phone.Plz help

I am using iphone 3gs since last 4 days. Till yesterday night it was working fine and i have connected this phone for charging . Morning there was apple logo in the screen and every 1mte (approx) it is blinking. I could not restart the phone.Plz help . I have tried to reset even by pressing sleep and home button but it could not help. Please suggest. Still i have connected for charging .

Sounds like you have corrupt backup data, if this occurs from one phone to another. Try restoring the phone as a new device, without a backup. Try using for a day before installing any other apps, etc. See if that improves the battery life. Then try syncing back applications a couple at a time. Something seems to be locking in the processor which is draining the battery.
Do you live in an area where there are Apple Stores? If so, try making an appointment with the Genius Bar to have the device checked out.

Lightroom 5.6 was working fine and now won't open at all.

Lightroom 5.6 was working fine and now won't open at all. Win8.1 64x
I backup my catalogues regularly and have tried different backups but still not opening. I have uninstalled and reinstalled to no effect

What happens when you try?
What is the error message?
What is your operating system?

Acrobat Pro IX License was activated and was working fine. Then it stop working application would not launch. I

My Acrobat Pro IX license was activated and was working fine. Then the application stop launching after an update was by Adobe. After a while I uninstalled the application successfully, logged on to my adobe account, viewed past purchases, re-downloaded the application successfully, activated the license and entered my serial number. The next day I get a pop up message that my trial licenses is set to expire in 29 days. I clicked again to activate my license and this time, the message stated that the license for serial number has been revoked.
How do I resolve this matter?
Darrell Rawlins

[discussion moved to Acrobat Installation & Update Issues forum.]

Time Capsule error 22 - My time capsule was working fine and didn't notice anything wrong with it until it stopped backing up about two weeks ago. I never changed anything like computer names or the Airport settings. All I get is the following: The backup

Time Capsule error 22 - My time capsule was working fine and didn't notice anything wrong with it until it stopped backing up about two weeks ago. I never changed anything like computer names or the Airport settings. All I get is the following:
The backup disk image "/Volumes/Data/Linda's Computer 1.sparsebundle" could not be created (error 22).
I tried resetting the Time Capsule and connecting with an ethernet cable, although the Ariport Utility says everything is working fine through WiFi.

If the light will not turn on the TC is dead. No matter that the hard disk is running.. it should only run at start up or when it is accessed not constantly.. that means the board in the TC has failed. Apple do not repair them.. They will replace it under warranty or applecare.
If you have gone over the 12month warranty it will still be covered if you have applecare on any computer or an Apple TV. In fact the cost of the apple TV plus apple care is still cheaper than buying a new TC.. so it is a route some people are taking.. certainly depends.. in some places like Europe or Australia now, there is a recognition that statutory warranty must be longer on a product that is premium to the market. 12months is not good enough. Apple will sometimes listen.
They might be fixable but I do not know how.

Is it possible to turn off the fluid grid function in dreamweaver during the process of building your site by mistake? It was working fine and simply stopped and I don't see how to correct what is wrong.

Is it possible to turn off the fluid grid function in dreamweaver during the process of building your site by mistake? It was working fine and simply stopped and I don't see how to correct what is wrong.

There is no specific function that turns FGL on or off.
When you say that it has stopped, do you mean that the handles no longer show?
If that is the case, then I think you may have modified the CSS to such an extent that Dreamweaver no longer recognises it as belonging to FGL.
There are a couple of avenues for you
Redo the site and make sure not to touch the FGL CSS
paste the code here so that we can see what has gone wrong.

HP Pavilion dv6 7039tx Notebook-It was working fine and then it suddenly got stuck during startup.

Similar Messages

Maybe you are looking for