HP vs15 monitor audio power supply voltage and amps

I have a HP vs15 monitor that I need to know the audio power supply voltage and amperage.

HI grizspeck:
Thank you for your inquiry.
I am sending you a link to the specifications of he HP Pavilion vs15 monitor  click here.
Sparkles1
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping!

Similar Messages

  • Use SNMP to monitor the power supply status of stacked switches

    Does anybody know how to use SNMP to monitor the status of the internal power supplies of a group of stacked Cisco 3750 switches?
    The switch stack has three 3750-48PS-E switches inter-connected by Cisco StackWise cable. IOS ver 12.1(19)EAlc. A single IP address is used to identify the switch stack. Every time I poll the OID chassisPs1Status (1.3.6.1.4.1.9.5.1.2.4.0 in CISCO-STACK-MIB), I only got the status for the Master switch of the switch stack. Is there any way to poll the power supply status of other switches in the switch stack?
    Thanks a lot!

    Sorry to refresh such an old topic - but I am stuck with exactly this: Monitoring power supplies of a stacked Cisco Catalyst 3750-E.
    I'm using the exact same OID's as described, but the problem is, the information shown on the SNMP output is not correct.
    This morning, a power supply of the first switch failed and switched to RPS. Here the information I got on SNMP:
    snmpwalk -v 2c -c public 192.168.1.50 1.3.6.1.4.1.9.9.13.1
    SNMPv2-SMI::enterprises.9.9.13.1.1.0 = INTEGER: 13
    SNMPv2-SMI::enterprises.9.9.13.1.3.1.2.1006 = STRING: "SW#1, Sensor#1, GREEN "
    SNMPv2-SMI::enterprises.9.9.13.1.3.1.2.2006 = STRING: "SW#2, Sensor#1, GREEN "
    SNMPv2-SMI::enterprises.9.9.13.1.3.1.3.1006 = Gauge32: 41
    SNMPv2-SMI::enterprises.9.9.13.1.3.1.3.2006 = Gauge32: 40
    SNMPv2-SMI::enterprises.9.9.13.1.3.1.4.1006 = INTEGER: 59
    SNMPv2-SMI::enterprises.9.9.13.1.3.1.4.2006 = INTEGER: 59
    SNMPv2-SMI::enterprises.9.9.13.1.3.1.5.1006 = INTEGER: 0
    SNMPv2-SMI::enterprises.9.9.13.1.3.1.5.2006 = INTEGER: 0
    SNMPv2-SMI::enterprises.9.9.13.1.3.1.6.1006 = INTEGER: 1
    SNMPv2-SMI::enterprises.9.9.13.1.3.1.6.2006 = INTEGER: 1
    SNMPv2-SMI::enterprises.9.9.13.1.4.1.2.1060 = STRING: "Switch#1, Fan#1"
    SNMPv2-SMI::enterprises.9.9.13.1.4.1.2.2059 = STRING: "Switch#2, Fan#1"
    SNMPv2-SMI::enterprises.9.9.13.1.4.1.3.1060 = INTEGER: 1
    SNMPv2-SMI::enterprises.9.9.13.1.4.1.3.2059 = INTEGER: 1
    SNMPv2-SMI::enterprises.9.9.13.1.5.1.2.1059 = STRING: "Sw1, PS1 Normal, RPS NotExist"
    SNMPv2-SMI::enterprises.9.9.13.1.5.1.2.2060 = STRING: "Sw2, PS1 Normal, RPS NotExist"
    SNMPv2-SMI::enterprises.9.9.13.1.5.1.3.1059 = INTEGER: 1
    SNMPv2-SMI::enterprises.9.9.13.1.5.1.3.2060 = INTEGER: 1
    SNMPv2-SMI::enterprises.9.9.13.1.5.1.4.1059 = INTEGER: 2
    SNMPv2-SMI::enterprises.9.9.13.1.5.1.4.2060 = INTEGER: 2
    As you see, both PS1 (for both switches) are appearing normal. It doesn't even recognize RPS:
    SNMPv2-SMI::enterprises.9.9.13.1.5.1.2.1059 = STRING: "Sw1, PS1 Normal, RPS NotExist"
    SNMPv2-SMI::enterprises.9.9.13.1.5.1.2.2060 = STRING: "Sw2, PS1 Normal, RPS NotExist"
    The first switch's power supply died and now the cable is disconnected. LED's of the power supply are out. And still: The switch happily announces by SNMP it's power supplies are up.
    Is this a known bug? If yes, has it been fixed?
    Model  WS-C3750E-48TD
    Firmware 12.2(37)SE1
    /* Style Definitions */
    table.MsoNormalTable
    {mso-style-name:"Table Normal";
    mso-tstyle-rowband-size:0;
    mso-tstyle-colband-size:0;
    mso-style-noshow:yes;
    mso-style-priority:99;
    mso-style-qformat:yes;
    mso-style-parent:"";
    mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
    mso-para-margin:0cm;
    mso-para-margin-bottom:.0001pt;
    mso-pagination:widow-orphan;
    font-size:11.0pt;
    font-family:"Calibri","sans-serif";
    mso-ascii-font-family:Calibri;
    mso-ascii-theme-font:minor-latin;
    mso-fareast-font-family:"Times New Roman";
    mso-fareast-theme-font:minor-fareast;
    mso-hansi-font-family:Calibri;
    mso-hansi-theme-font:minor-latin;
    mso-bidi-font-family:"Times New Roman";
    mso-bidi-theme-font:minor-bidi;}

  • Help : power supply- voltage regulator

    Thank you for all those that have replied me towards this power supply.  In particular Lacy and Kittmaster.
    I have developed a basic voltage regulator . However, I want to get a power supply that can deliver like 60V, and take about 10A current, because that what the load will require.
    The regulator I have developed only delivers about 20V, I use the formula Vo = (R2/R3 + 1) * Vref. where my Vref is now 10V ( 2 zener diode). Even when I tried to decrease the resistance of R3, it does not make a difference.
    Any help will be appreciated.
    Attachments:
    Power Supply Voltage Regulator.ms9 ‏1107 KB

    O.K. I believe I have got it. There was a 2 fold problem with your regualtor and I will outline them below.
    1) For some reason I could not get the 3-terminal Virtual Op Amps to work in this circuit. I traded that out for the 5 Terminal one. It is the very last one in the list of the Virtual category.
    2) You are comparing your voltage from the bridge to your output voltage. If you have your input referenced to 10V and your output dviding this by a factor of 2 then once the voltage at the divider junction reaches 10V then the op amp will stop driving the transistor. Therefore you are only going to get 20V Out (ref*2 since both resitors are equal in value)). Therefore, you have to have your input reference to what you want the output to be. In this case 60V is what you want so you have 30V at the divider junction (Vo/2 since both resitors are equal value) your input reference would have to be 30V. I have never heard of a 30V Zener (they may exist, but it seems to me tha they would have to be quite large). so you may have to use a voltage divider on the input side instead.
    It is my opinion that the design of this regulator is not going to work for you in reality if you decide to build it. The 2N2904 I I know is not going to handle 10A in reality. Based upon my findings I don't even know if you are going to be able to use an op-amp as the error amp due to the amount of voltage that has to be tied into it.You may be able to find such an op-amp but you will have to do some research to find one. I think most of the op amps in Multisim are low voltage in the range of 5VDC-22VDC. I would suggest looking  on the internet and see if I could find a better alternative that uses more robust components or if you definitely want to design this on your own, reasearching the components in Multisim to see if any of them can handle the voltage and current requirements.
    I hope this helps and I haven't confused you in any way
    Message Edited by lacy on 10-06-2007 02:24 PM
    Kittmaster's Component Database
    http://ni.kittmaster.com
    Have a Nice Day

  • Power supply voltage for using PoE splitters

    Dear Community
    What is the power supply voltage for Apple TV 3?
    Power consumption has been specified on the Apple product site, but not the power supply voltage.
    Should be 5, 9 or 12 Volt.
    Thanks!

    http://docs-europe.electrocomponents.com/webdocs/0d88/0900766b80d88153.pdf
    Every Expert was once a Beginner!!

  • Power supply voltage upper-non-recoverable

    Hello,
    One of our customers is seeing the following errors occur intermittently across all 4 power supplies in their chassis. They are running 2.0(2q). The chassis is powered via an APC UPS and PDUs, and there are no power events or alarms from within the APC InfraStruxure tools. Has anyone else seen these errors in 2.0(2q) or is this error indicating a voltage fluctuation from the UPS?
    Sent: Monday, April 30, 2012 6:26 AM
    To: ITNotify
    Subject: System Notification from PFS-UCS-A - environment:major - 2012-04-30 12:26:39 GMT-00:00 Recovered : Power supply 4 in chassis 1 voltage: upper-non-recoverable
    <?xml version="1.0" encoding="UTF-8" ?>
    <soap-env:Envelope xmlns:soap-env="http://www.w3.org/2003/05/soap-envelope">
    <soap-env:Header>
    <aml-session:Session xmlns:aml-session="http://www.cisco.com/2004/01/aml-session" soap-env:mustUnderstand="true" soap-env:role="http://www.w3.org/2003/05/soap-envelope/role/next">
    <aml-session:To>http://tools.cisco.com/neddce/services/DDCEService</aml-session:To>
    <aml-session:Path>
    <aml-session:Via>http://www.cisco.com/appliance/uri</aml-session:Via>
    </aml-session:Path>
    <aml-session:From>http://www.cisco.com/appliance/uri</aml-session:From>
    <aml-session:MessageId>1232:SSI15420KDL:4F9E84FF</aml-session:MessageId>
    </aml-session:Session>
    </soap-env:Header>
    <soap-env:Body>
    <aml-block:Block xmlns:aml-block="http://www.cisco.com/2004/01/aml-block">
    <aml-block:Header>
    <aml-block:Type>http://www.cisco.com/2005/05/callhome/environment</aml-block:Type>
    <aml-block:CreationDate>2012-04-30 12:26:39 GMT-00:00</aml-block:CreationDate>
    <aml-block:Builder>
    <aml-block:Name>UCS 6248 Series Fabric Interconnect</aml-block:Name> <aml-block:Version>5.0(3)N2(2.02q)</aml-block:Version>
    </aml-block:Builder>
    <aml-block:BlockGroup>
    <aml-block:GroupId>1233:SSI15420KDL:4F9E84FF</aml-block:GroupId>
    <aml-block:Number>0</aml-block:Number>
    <aml-block:IsLast>true</aml-block:IsLast>
    <aml-block:IsPrimary>true</aml-block:IsPrimary>
    <aml-block:WaitForPrimary>false</aml-block:WaitForPrimary>
    </aml-block:BlockGroup>
    <aml-block:Severity>6</aml-block:Severity>
    </aml-block:Header>
    <aml-block:Content>
    <ch:CallHome xmlns:ch="http://www.cisco.com/2005/05/callhome" version="1.0">
    <ch:EventTime>2012-04-30 12:26:39 GMT-00:00</ch:EventTime> <ch:MessageDescription>Recovered : Power supply 4 in chassis 1 voltage: upper-non-recoverable</ch:MessageDescription>
    <ch:Event>
    <ch:Type>environment</ch:Type>
    <ch:SubType>major</ch:SubType>
    <ch:Brand>Cisco</ch:Brand>
    <ch:Series>UCS 6248 Series Fabric Interconnect</ch:Series> </ch:Event> <ch:CustomerData> <ch:UserData> <ch:Email>[email protected]</ch:Email>
    </ch:UserData>
    <ch:ContractData>
    <ch:SiteId>2089409</ch:SiteId>
    <ch:ContractId>90874841</ch:ContractId>
    <ch:DeviceId>UCS-FI-6248UP@C@SSI15420KDL</ch:DeviceId>
    </ch:ContractData>
    <ch:SystemInfo>
    <ch:Name>PFS-UCS-A</ch:Name>
    <ch:Contact>IT Department</ch:Contact>
    <ch:ContactEmail>[email protected]</ch:ContactEmail>
    <ch:ContactPhoneNumber>+18018442180</ch:ContactPhoneNumber>
    <ch:StreetAddress>1420 South 500 West, SLC UT 84115</ch:StreetAddress> </ch:SystemInfo> </ch:CustomerData> <ch:Device> <rme:Chassis xmlns:rme="http://www.cisco.com/rme/4.0">
    <rme:Model>UCS-FI-6248UP</rme:Model>
    <rme:HardwareVersion>0.0</rme:HardwareVersion>
    <rme:SerialNumber>SSI15420KDL</rme:SerialNumber>
    </rme:Chassis>
    </ch:Device>
    </ch:CallHome>
    </aml-block:Content>
    <aml-block:Attachments>
    <aml-block:Attachment type="inline">
    <aml-block:Name>sam_content_file</aml-block:Name>
    <aml-block:Data encoding="plain">
    <![CDATA[
    <faultInst
    ack="no"
    cause="voltage-problem"
    changeSet=""
    code="F0391"
    created="2012-04-30T06:25:39.162"
    descr="Power supply 4 in chassis 1 voltage: upper-non-recoverable"
    dn="sys/chassis-1/psu-4/fault-F0391"
    highestSeverity="critical"
    id="218782"
    lastTransition="2012-04-30T06:26:39.630"
    lc=""
    occur="1"
    origSeverity="critical"
    prevSeverity="critical"
    rule="equipment-psu-voltage-threshold-non-recoverable"
    severity="cleared"
    status="modified"
    tags="network,server"
    type="environmental"/>]]>
    </aml-block:Data>
    </aml-block:Attachment>
    </aml-block:Attachments>
    </aml-block:Block>
    </soap-env:Body>
    </soap-env:Envelope>

    Brad,
    It looks like the system is running into following defects which is still under investigation.
    http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCtx90410
    http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCtz59519
    Please open a TAC service request so that we can help you out.
    HTH
    Padma

  • Plotting IVI Power Supply voltage

    I am usint SignalEpxress to control to my Agilent N6700B power supply, and I am successfully commanding the instrument and querying the output voltage. 
    However, I can't seem to figure out how to plot the output voltage on a strip chart. The 'IVI Power Supply' step only seems to offer two output options:
    'over-voltage tripped'
    'over-current tripped'
    It doesn't therefore seem possible to hook the output voltage of the step to a data view strip chart. Any ideas on how to accomplish this?
    Thanks,
    Aaron

    @astibich, just out of curiosity, can’t you accomplish the same in software. Since you’re getting the required values of voltage, you can plot that within the PC. If required these values could then be transmitted to a real-time plotter as well. If you’ve already found a better solution to this, I’d love to know, just for information. It’s the ingenious ideas of people that actually inspire me, like everyone else, to think outside the box.
    printed circuit boards

  • Airport Extreme Power Supply Voltage?

    We just moved and apparently packed our AEBS separately from the power supply. Does anyone know the voltage and output current (or power) from the power supply so that I might use an alternative until we find the original?
    I hate to spend the $20 (and shipping) for a unit I'll find some days from now...
    Thanks,

    The Airport Extreme power supply brick output is rated at 5.1V DC, 2.4 A. The polarity of the plug's sleave is negative, the center terminal is positive.

  • Power supply died, and now video card is malfunctioning

    I had the power supply in a 24in iMac (16 months old) replaced yesterday after the computer malfunctioned (Thought it was the hard drive, tech said it was power supply and seemed to have been correct).
    The hard drive was formatted prior to sending it off to be repaired so i get it back and go to install Leopard and the resolution looks low. I install OSX anyway thinking it may be a software issue. But that didnt help. All menus have a slight pink tinge to them. Desktop background is pixalted and just ... low resolution looking.
    The video card was fine before bringing it in. I can't see why it would suddenly do this. if the video card was messed up, I would expect it to just not display anything.
    The monitor is set to 1920 x 1200 and it is correctly displaying at that resolution. It s just that colors are off and images are pixelated. Dont know how else to describe it.
    Any ideas?

    Here is an image.
    Also the background image is sort of pulsating. Really strange. http://uploader.ws/upload/200907/Picture11.jpg
    Edit: You may have to right click and open in new window
    Edit 2: Just looked at this on my other computer and it looks fine... Ill take a picture with my phone but I assume if the screen shot captured doesn't have the display malfunction that I am seeing, it means the video card is dead? Or the logic board? Arggg.
    Edit 3: Picture taken with iPhone so you can see what I see
    http://uploader.ws/upload/200907/photo_2.jpg
    Message was edited by: Vuguru

  • My Macbook Pro with Remakes funny noise when connected to power supply cable and no other response. The best description of the sound I can give is the buz the computer makes on startup. Sound goes on and off while connected

    I am new to the Macbook community. I own this Macbook since 10/2012.
    My Macbook Pro 15 with Retina Display suddenly totally stopped responding. No display, no activity on keyboard. When I connect power supply cable, the Mac makes a noise as if it is starting up, but this lasts a second and this sound comes and goes the whole time the power cable is connected.
    Any advice?
    Thanks!

    Reset the SMC and the NVRAM:
    http://support.apple.com/en-us/HT201295
    http://support.apple.com/en-us/HT204063
    The try a safe boot:
    http://support.apple.com/en-us/HT201262
    Any change?
    Ciao.

  • Hub NH1005 vers 2 Need power cube voltage and current requirements

    I picked up a Linksys hub model NH1005 v.2 at a yard sale. I want to use it with a router as I have used up all 4 ports on the router. However the hub did not have the power cube. Can anyone please tell me what voltage and ma it requires? Thanks for any help you can ofer.
    Bob-r

    5V 1.5A

  • E30 power supply/cables and upgrading video card.

    I'm thinking of buying a decent gaming card, but I can't seem to find any power cables inside my system. The video card I'm looking at has a six pin connector on it. Also, just in case I need to upgrade the power supply, is the power supply unit standard ATX?
    Solved!
    Go to Solution.

    welcome to the forum!
    the E30 doesn't come with a PCI power connector due to it only being qualified to run the quadro NVS, 400, 600, and 2000/2000D workstation graphics cards.   you would need a different PSU entirely.   due to warranty and support reasons we can't recommend aftermarket PSUs in this system.
    besides, depending on the GPU you're considering, the E30 might not have sufficient airflow to support it.   these are workstations after all and not gaming systems.
    similar advice was given to another E30 owner in this thread.   i'm not sure what makes the E30 such a compelling gaming platform but to each their own.
    ThinkStation C20
    ThinkPad X1C · X220 · X60T · s30 · 600

  • No power. Power supply connected and green live shows current. photosmart c310.

    This barely used piece of crap lost all its power shortly after warranty expired.  This is evidently a common problem as there are all kinds of mention of it on the web. It was evident before I bought this thing.  Only solution by HP is to buy power supply for $16.50 and spend $11 to have it shipped.   I don't even know if this will correct problem.  Would like to hear from someone who has solved this problem.

    OK, if you plug the printer in and it does not power up with no lights, it could be the power supply.  If you change the power supply and you have the same problem, the printer is defective and you need to have it serviced.
    Say thanks by clicking the Kudos Thumbs Up to the right in the post.
    If my post resolved your problem, please mark it as an Accepted Solution ...
    I worked for HP but now I'm retired!

  • 600 watt power supply questions and video card upgrade questions

    I am looking to upgrade to a Xfx Radeon 7970 Double D graphics card but i was wondering if the HP 600w psu that came with my Hp Envy Phoenix H9-1350 has a 8 pin and 6 pin Pci-e connector because that is what the Radeon 7970 needs. Also I am wondering if it will fit into the Hp Envy Phoenix H9-1350 because the case seems small but the card is only 9.3" long. I currently have an Amd Radeon 7670 but I think it is time for an upgrade but I am just not sure if the power supply has the correct power connections needed for the Radeon 7970.
    This is the card I am looking to get:
    http://www.newegg.com/Product/Product.aspx?Item=N8​2E16814150665
    This is the computer I have:
    http://www.bestbuy.com/site/HP+-+ENVY+Phoenix+Desk​top+-+12GB+Memory+-+2TB+Hard+Drive/6890832.p?id=12​...

    I understand you want to know if the power supply will have the necessary connectors for the desired video card.
    According to the specifications, it lists the case as a mini-tower which is on the small side.  You may need to use a tape measure to find out exactly how much room the system has in regards to length.  It has become much better, but other components (such as the HDD) were at the end of the PCIe slot limiting the length of a video card.  Sorry I couldn't provide anything more specific.  The manuals are somewhat vague as far as the internal dimensions and I don't have access to one to verify the dimensions.  
    Ordinarily, I can find more information regarding the power supply not that seems not to be the case here.  According to this thread, the PSU has two 6 pin PCIe connectors.  You would need something like this to convert one of the 6pin connectors to 8pin.  As long as the PSU is capable of pushing enough watts, it shouldn't be an issue.  The card needs up to a 500W power supply, so the 600W power supply should be just enough to cover it.
    ↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓

  • Power Supply - US and UK Electricity

    I brought my iMac G5 to London, UK from San Francisco where I bought it. When I plugged it in, the thing blew up!! Big Bang and Big Spark! Two Questions:
    1. Isn't the power supply supposed to work with both 120 and 240 AC?
    2. If someone fits a new power supply here in London, will it DEFINITELY WORK back in the US?

    Most Macs have a universal or self-adjusting power supply. However, I have heard that there have been models that were not. It behoves everyone to definitively know the power consumption of their Mac and not make costly assumptions.
    If an authorized service center refits your Mac with a new power supply do not assume again that it is universal. Ask them what they are installing, and what are its limits. Perhaps your have a choice. Perhaps it can be fitted with a universal power supply.
    Good luck. Hopefully the damage is limited to the power supply.

  • External Power Supply: Voltage?

    Dear iPodders,
    What voltage is safe to put into the dock connector of an iPod classic?
    The travel power pack only seems to deliver 5v to it, but I've got a cable to use for connection to an in-car stereo, and it has a power feed that connects directly to the +12v of the car's battery!
    Is this OK? Or is this dangerous?
    - Dave

    On the iPod there are two ways to get power into it. On the dock connector there are power input pins for USB and power input pins for Firewire. USB is +5V while Firewire is often +12V but can be a lot higher. On the Firewire pins you can input over 30V. What I am not sure about is if you can input more than 5V on the USB power pins since USB is standardized at 5V but that doesn't mean the iPod can't accept more on those pins.
    Anyway, the automobile connection is very likely wired up to deliver the +12V car battery voltage to the Firewire power pins of your iPod Classic and that is normal/acceptable.
    Patrick

Maybe you are looking for