HT3867 how much is it to join a network

How much is it to join a network

Huh?
It depends on the network.
Your home network would cost nothing extra.
Many hotels, hospitals, airports etc have free wi-fi, others charge.

Similar Messages

How can a Time Capsule join the network offered by an Airport Express?

What I want is for any machine to still be able to access the internet.
and for any machine to still be able to access the time capsule.
So I want all machines connected to the same network. So isn't it possible
to make the Timecapsule available to all machines by joining the main network yet still be plugged into ethernet into my machine machine?
Computer is in living room hence need for TC to be closer and ethernet where as the internet connection is in the bedroom which is where the Airport Express is.
Currently no other machine except the one that's plugged into the Time Capsule's ethernet hub can see the Time Capsule wirelessly.

What I want is for any machine to still be able to access the internet.
and for any machine to still be able to access the time capsule.
So I want all machines connected to the same network. So isn't it possible
to make the Timecapsule available to all machines by joining the main network yet still be plugged into ethernet into my machine machine?
Computer is in living room hence need for TC to be closer and ethernet where as the internet connection is in the bedroom which is where the Airport Express is.
Currently no other machine except the one that's plugged into the Time Capsule's ethernet hub can see the Time Capsule wirelessly.

How Can We Tune the Joins with "OR" Caluse ?

Hi
We've identified one Query in one of Our PL/SQL Stored Procedure which is taking huge time to fetch the records. I have simulated the problem as shown below. The problem Is, How can i tune the Jions with "OR" Clause. i have tried replacing them with Exists Caluse, But the Performance was not much was expected.
CREATE TABLE TEST
(ID NUMBER VDATE DATE );
BEGIN
FOR i IN 1 .. 100000 LOOP
    INSERT INTO TEST
    VALUES
      (i, TO_DATE(TRUNC(DBMS_RANDOM.VALUE(2452641, 2452641 + 364)), 'J'));
    IF MOD(i, 1000) = 0 THEN
      COMMIT;
    END IF;
END LOOP;
END;
CREATE TABLE RTEST1 ( ID NUMBER, VMONTH NUMBER );
INSERT INTO RTEST1
SELECT ID, TO_NUMBER(TO_CHAR(VDATE,'MM'))
FROM TEST ;
CREATE TABLE RTEST2 ( ID NUMBER, VMONTH NUMBER );
INSERT INTO RTEST2
SELECT ID, TO_NUMBER(TO_CHAR(VDATE,'MM'))
FROM TEST;
CREATE INDEX RTEST1_IDX2 ON RTEST1(VMONTH)
CREATE INDEX RTEST2_IDX1 ON RTEST2(VMONTH)
ALTER TABLE RTEST1 ADD CONSTRAINT RTEST1_PK PRIMARY KEY (ID)
ALTER TABLE RTEST2 ADD CONSTRAINT RTEST2_PK PRIMARY KEY (ID)
SELECT A.ID, B.VMONTH
FROM RTEST1 A , RTEST2 B
WHERE A.ID = B.ID
AND ( (A.ID = B.VMONTH) OR ( B.ID = A.VMONTH ) )
BEGIN
DBMS_STATS.gather_table_stats(ownname => 'PHASE30DEV',tabname => 'RTEST1');
DBMS_STATS.gather_table_stats(ownname => 'PHASE30DEV',tabname => 'RTEST2');
DBMS_STATS.gather_index_stats(ownname => 'PHASE30DEV',indname => 'RTEST1_IDX1');
DBMS_STATS.gather_index_stats(ownname => 'PHASE30DEV',indname => 'RTEST2_IDX2');
DBMS_STATS.gather_index_stats(ownname => 'PHASE30DEV',indname => 'RTEST1_IDX2');
DBMS_STATS.gather_index_stats(ownname => 'PHASE30DEV',indname => 'RTEST2_IDX1');
END; Pls suggest !!!!!!! How can I tune the Joins with "OR" Clause.
Regards
RJ

I don't like it, but you could use a hint:
SQL>r
1 SELECT A.ID, B.VMONTH
2 FROM RTEST1 A , RTEST2 B
3 WHERE A.ID = B.ID
4* AND ( (A.ID = B.VMONTH) OR ( B.ID = A.VMONTH ) )
Execution Plan
   0      SELECT STATEMENT Optimizer=CHOOSE (Cost=94 Card=2 Bytes=28)
   1    0   TABLE ACCESS (BY INDEX ROWID) OF 'RTEST2' (Cost=94 Card=1 Bytes=7)
   2    1     NESTED LOOPS (Cost=94 Card=2 Bytes=28)
   3    2       TABLE ACCESS (FULL) OF 'RTEST1' (Cost=20 Card=100000 Bytes=700000)
   4    2       BITMAP CONVERSION (TO ROWIDS)
   5    4         BITMAP AND
   6    5           BITMAP CONVERSION (FROM ROWIDS)
   7    6             INDEX (RANGE SCAN) OF 'RTEST2_PK' (UNIQUE)
   8    5           BITMAP OR
   9    8             BITMAP CONVERSION (FROM ROWIDS)
10    9               INDEX (RANGE SCAN) OF 'RTEST2_IDX1' (NON-UNIQUE)
11    8             BITMAP CONVERSION (FROM ROWIDS)
12   11               INDEX (RANGE SCAN) OF 'RTEST2_PK' (UNIQUE)
Statistics
          0 recursive calls
          0 db block gets
     300332 consistent gets
          0 physical reads
          0 redo size
        252 bytes sent via SQL*Net to client
        235 bytes received via SQL*Net from client
          2 SQL*Net roundtrips to/from client
          0 sorts (memory)
          0 sorts (disk)
          2 rows processed
SQL>SELECT /*+ ordered use_hash(b) */ A.ID, B.VMONTH
2    FROM RTEST1 A, RTEST2 B
3   WHERE A.ID = B.ID AND(A.ID = B.VMONTH OR B.ID = A.VMONTH)
4 ;
Execution Plan
   0      SELECT STATEMENT Optimizer=CHOOSE (Cost=175 Card=2 Bytes=28)
   1    0   HASH JOIN (Cost=175 Card=2 Bytes=28)
   2    1     TABLE ACCESS (FULL) OF 'RTEST1' (Cost=20 Card=100000 Bytes=700000)
   3    1     TABLE ACCESS (FULL) OF 'RTEST2' (Cost=20 Card=100000 Bytes=700000)
Statistics
          9 recursive calls
          0 db block gets
        256 consistent gets
        156 physical reads
          0 redo size
        252 bytes sent via SQL*Net to client
        235 bytes received via SQL*Net from client
          2 SQL*Net roundtrips to/from client
          0 sorts (memory)
          0 sorts (disk)
          2 rows processed

How much UNDO does a query need?

It seems that due to a gigantic delete, I am running out of UNDO. How can I see exactly how much undo a query needs?
Searching on the web, I found this:
select sq.sql_text sql_text, t.USED_UREC Records, t.USED_UBLK Blocks, (t.USED_UBLK*8192/1024) KBytes from v$transaction t,
v$session s,
v$sql sq
where t.addr = s.taddr
and s.sql_id = sq.sql_id
and s.username = 'blah'
, which is fine, but it seems to be returning results for only running queries. In other words, when the delete query I am investigating is executed, the above select returns no rows. Is there a way to modify it to return also queries that have been executed?
Any help is welcome.
Message was edited by:
user622271

Hi,
It seems that you need to make an outer join between v$sql and v$session views [s.sql_id = sq.sql_id(+)] ... For more information is if this [url http://forums.oracle.com/forums/thread.jspa?messageID=1756927&#1756927]thread can help you.
Cheers
Legatti

How do I tell how much hard disk space an archive will take up?

Hi we are trying to determine whether or not we have the capacity to run an archive export on one of our WebCenter spaces content folder (the root folder and ALL contents). Before we begin we'd like to be able to tell how much disk space it will take up.
Thanks,
S

The table Documents contains a field called dFileSize, which contains the size of file in bytes.
Now, you can use this field to calculate the size of all files contained in a folder (or its subfolders), or contained in an archiving batch.
I think easier is the former. Actually, I have done something similar - created a component that checks so that files in a folder do not exceed the given quota. It already contains hierarchical queries that could be re-designed (simplified) to your needs. For instance, an occupied quota of a folder is
WITH tree AS (select dCollectionId, case when level>1 then dCollectionQuota end as effective_quota from collections start with dCollectionId = ? connect by dParentCollectionId = prior dCollectionId and (prior dCollectionQuota IS NULL or level = 2)) SELECT SUM(NVL(t.effective_quota, NVL(docs.dFileSize, 0))) as TOTALDOCUMENTSIZE from tree t LEFT OUTER JOIN DOCMETA meta ON t.dCollectionId = meta.xCollectionId and t.effective_quota IS NULL LEFT OUTER JOIN DOCUMENTS docs ON meta.dId = docs.dId and docs.dIsPrimary = 1 LEFT OUTER JOIN REVISIONS rev ON rev.dId = docs.dId(in your case, you don't need t.effective_quota, nor logic bound to dCollectionQuota as these values do not exist in your system)
P.S. more info about hierarchical queries, see here
http://docs.oracle.com/cd/E11882_01/server.112/e10592/queries003.htm#i2053935
http://docs.oracle.com/cd/E11882_01/server.112/e10592/statements_10002.htm#i2077142

How to create a left join view in se11??

I would like to create a view which contains KNA1,KONA,KNVV,KNVH(four tables) , I want to use this view to create a search help for Tcode 'VBO3'.
but when I join table KNVH, there is no data in view, because there is no customer hierarchy, so I want to create a left join view. could you please tell me how to create a left join view? Thank you very much.

Hello,
yes, in general, maint. view and help view could be created as outer join view.
but it should obey relationship.
my fourt tables:
KONA -
> I want to get agreement number and type from this table
KNA1 -
>I want to get customer name, city, country from this table
KNVH -
>I want to get customer hierarchy from this table.
KNVV -
>I want to get customer group 1 from this table.
but in help view, I can only get relationship between KONA and KNA1.
I could not find the relationship for KNVH and KNVV.
if it's required to add a search help exit, then how to write the code in the function?
Could somebody please give me any solutions? thank you.

How much time does an AP take to failover to secondary controller

hi All,
My query is to understand how much time will an AP take to failover to its secondary WLC(Backup) incase primary goes offline.
Whats the heartbeat time for each AP to verify reachability to WLC.
also what is the purpose of AP Fail over priority under each AP. i want to ensure AP's fall back to primary WLC once its back online.(Preemption)

Hi Matehw,
My query is to understand how much time will an AP take to failover to its secondary WLC(Backup) incase primary goes offline.
We can not tell exact time but normally It takes 1-3 minutes.
Whats the heartbeat time for each AP to verify reachability to WLC.
AP Heartbeat Timeout - AP sends heartbeat to WLC (By default its 30s). Once the primary WLC(or where AP is connected to)goes down, With heartbeats, the AP realizes sooner that the controller has become unreachable.
also what is the purpose of AP Fail over priority under each AP.
First of all there are three types: it goes like this Cirtical...high...medium..low.
***To configure AP failover priority, we must enable AP Fallback feature globally and then individual APs with a suitable priority level.
*** When using both the local and global backup configurations, the locally configured settings take precedence in the event of a controller failure. If an AP is not able to join any of the locally configured controllers, it then tries to join the global backup controllers.
More info:
http://rscciew.wordpress.com/2014/01/22/ap-failover/
Regards
Dont forget to rate helpful posts

How much is the myipodownloads.ocm membership?

I found this listed popular movie down load web site-myipodownloads.com. I was interested to be a member so I can downloads CCN or movies but they asked for my credit card no. upfront before anything else. I think they are either too clever or very dump. Who on earth would give them credit card information without knowing the cost of first. Has anyone join this .com and if so what's the one time membership like?
They mentioned all the advantages of joining except the crucial information, as to how much it will cost to be a lifetime member.

Fine thanks for the alert!

HT201058 How much iCloud data do you get using Family Sharing?

If I add both of my daughters to my Family Sharing, how much iCloud storage do we get between the 3 of us?
Is it worth joining ID's, if we only have 5GB to share between us, considering we are all using over 4GB each now.

I would also like to know how I can merge a Apple ID with another ID?
I set up my daughters ID's about 3 years ago, but I had to add 10 years to their Date Of Birth, else I could not get them ID's. Now when I have added my daughter to my Family Sharing, it states she is an adult, and it will not let my change her DOB. Apple says I have to setup a child ID within Family Sharing.
So, can I change a Adult ID to a Child ID, or merge a Adult ID to a new Child ID?

How much will GPU upgrade for Dual 1.25 G4 FW800 help HD rendering times

--"Oh great, not another 'I have an ancient Mac' thread, time to join the 21st century!"
Please hear me out. I don't have a lot of money. Any money I have needs to go to video/photography needs since that is my job. If I bought a proper editing station I couldn't afford to shoot. Currently I shoot HDV but will be shooting Canon 5D mark ii (h.264) soon. I use FCS2, but since I have a Dual 1.25 G4 FW800 I can't use Color or Motion. I would "like" to explore those programs.
Why don't I face reality and buy a new Mac? Because after reading threads like this I am afraid of missing the alleged 32nm Arrandale MBP coming out in a year. The past 7 years with the desktop I've needed to go portable at times so I'd like to get the MBP. I understand it will probably only last ~half as long as would a MacPro. Maybe I'll get rich and can buy a MacPro in a few years...
This Arrandale possibility has me shaken up. I've put off buying a new Mac for so long. I really haven't "needed" to edit intensively. A TV show I'm on is ending and I want to be doing more of my own stuff in the near future. How much, I don't know.
Would buying a new GPU such as the ATI 9800 Pro help me get back into the game? Could I use Color or Motion effectively and will render times in FCP6 be better? I've tried searching here and elsewhere and am certain this had to come up but can't find anything specific to my question. I run Leopard but could go back to Tiger if need be. I've read all the system requirements but want to know first hand knowledge, from those who've tried (FCS2 with a PPC G4). Is it worth an upgrade to hold out another year for a MBP?
Anything else I should say?

I wouldn't wait another day. There will always be some incredible new upgrade around the corner. Using G5s with HD makes me go insane. I can't imagine a G4. A new graphics card will not help you. Shooting with the Canon 5D will require you to render your h.264 video to an editable format. That only uses the CPU. The GPU will only expend its energy drawing the slowly-updating progress bar on screen. Last week I was on location with a year-old MBP and the conversion times for Canon 5D footage were a bit too long for my tastes. Doing it with an 8-core Mac Pro is significantly better.

How much space does iOS 6 or iOS 7 require?

On a 8 GB iphone how much space does iOS 6 or iOS 7 take up?

No one can tell you specifically, as it will vary by device and user and according to your personal data on the device etc. But, you can expect anywhere roughly around 175-195MB.
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

How much space does OS 6 require ?

Hello again,
Friends do let me know how much space is require for OS 6 in 9300. and does is it true that OS 6 make 9300 very slow in processing anything ??
Thank you in advance.
Regards,
Anwar A
Solved!
Go to Solution.

No one can tell you specifically, as it will vary by device and user and according to your personal data on the device etc. But, you can expect anywhere roughly around 175-195MB.
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

I am thinking of buying an imac presently using a PC with photoshop 7.0. Can I change over and how much does it cost.

I am thinking of changing over from the "PC" system to an Imac. Presently we have Photoshop 7.0 and would like to know if we can cross change? and how much it would cost. I found trying to contact Adobe directly using a phone, very frustrating, if not impossible? I got caught up in an endless circle, even though I tried different.choices each time.
Wayne

I know that the program is old, however it was expensive to buy and I am really familiar with how it works, so that's why I would like to be able to do the cross over.
I don't work for Adobe but I can respond to a couple of your questions with certainty:
There is no upgrade (or crossgrade) path from Photoshop 7 Win to Photoshop 7 for Mac. That window closed many years ago.
Photoshop 7.0 will not run on modern Intel-based Macs. It was written for old PowerPC based Macs and the code will not run on Intel chips without Rosetta which is no longer available in current OS X operating systems.
System requirements | Photoshop
Your options for your new Mac
Buy Photoshop CS6 for Mac full version
Buy Photoshop Elements 13 for Mac
Join the Cloud and pay the monthly fee

How much of the chat

Was already in a bbm conversation with a new Q10. Somehow i included a second person to the chat in error. How much of the old chat did this "second" contact receive? Would they just get the portion from when they were joined or all the old convo as well?

Hi Billy,
I would suggest that you give Kaazing's WebSocket platform a try. It's Java-based and comes with Java WebSocket libraries, including JMS over Websocket if that is of interest. There are several tutorials and the free download comes with tutorial like demos.
http://www.kaazing.com/developers
http://demo.kaazing.com/demo/jms/javascript/ (there are links on the side for other client technologies)
Good luck,
JonteWS

Twitter App - how much to use

Hi
Sorry, new to BB and to smartphones..
The twitter app is shown as free to download, but what is the running cost of using it? What charges are imposed. Similarly with the music apps, free to download but how much to use?

Data in BlackBerry terms is the flow of electronic information to and from your device, over the network.
Anyway, so now you know. Twitter uses data. BBM uses data. GPS navigation mapping applications use data to flow the maps to your handheld.
However, SMS is not "data", it is part of the "voice" pipe.
Consider your BlackBerry having TWO inlets for information.
The voice "pipe" channel contains the voice and SMS
The data "pipe" channel contains all over flow of information: email, twitter, BBM, mapping, internet browser, etc.
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

HT3867 how much is it to join a network

Similar Messages

Maybe you are looking for