HT5654 my iphone 5 fell did not break but went completely black and non responsive. When I plug it to the computer I get a white screen with black apple. When I push both the Top and Homne buttons simultaneously I get the charger picture plug end plus arr

my i phone 5 was dropped, didn't break but went completerly black screen and nonresponsive. I pushed both the home button and top button no response. I plugged it to the computer it gave me white screen with black apple. I pushed the home and the top went black then gave the itune and the charging plug picture. I tried to download and update, the message came as couldn't restore due to unknow error. Any help??

Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

Similar Messages

I have a mid-2011 iMac running Mavericks. When I click restart the computer goes to a white screen with a spinning circle and does not go any further until I hold down the power button to turn it off. What do I do?

I have a mid-2011 iMac running Mavericks. When I click restart the computer goes to a white screen with a spinning circle and does not go any further until I hold down the power button to turn it off. What do I do?

Ok, sounds like the safe mode boot worked... You probably don't want to always be in safe mode though (some reduced functionality) so does it do a normal boot now? If not, you should then reboot into safe mode and run Disk Utility. Then select Macintosh HD on the left hand side, and click the Verify Disk button. If needed, it will ask you to Repair Disk. If there are errors found, Repair Disk again until there are none. Then try another normal boot and reply with result, wether good or bad.

What do I do when I start my iMac I get a white screen with an apple and a moving circle?

All I get when my iMac is turned on is a white screen with an apple and a moving circle. What should I do to get the iMac to boot?

Do you have reliable backup you can restore from, as an erase and re-install may be required?
Before you got down that route, it's possible that it might get fixed if you try again. Not sure about that particular error, but I have had errors in the past that Disk Utility wouldn't fix on the first attempt but then subsequently did.
It's also possible that the (around $99, I think) Disk Warrior might resolve it - but not guaranteed.
However, I just found this thread: https://discussions.apple.com/thread/3862376?start=15&tstart=0 have a look at Nirvi's post at the end - there may be hope (I've not tried this, although it seems to have helped a few, although not everybody - so at your own risk and I wouldn't try it if I didn't have backup).

HT201412 My I phone five isn't responding and when I turn it on, I get a white screen with black lines and I can't get into my phone. What is happening?

My iPhone five decided to go crazy and give me a white screen with black stripes and I can't get into my phone. I can only use Siri! What's happening?

You posted in the iPad forum instead of the iPhone forum. To get answers to your question, next time post in the proper forum. See https://discussions.apple.com/index.jspa I'll request that Apple relocate your post.
 Cheers, Tom

When i turn on my Mac book air I get a white screen with an apple and spinning pinwheel

Why won't my Mac book air turn on? I get a white screen with apple and spinning pinwheel.

If you wish help you are going to have to tell us more then that.
What version of OS X is your MBA running?
What did you change before this started?
Allan

HT1758 Power failure in the middle of a software update and not the computer will not boot up. The computer just has a white screen with a grey apple and just loads non stop.

My iMac will not boot up after a software update. the screen is all whute will show a grey apple in the middle and will look like it is working but nothing happens; this can go on forever.
Does anyone have any suggestions?

Do you have a backup in the form of a bootable clone or Time Machine? Restore that and then try the update again.
Some things to try here (Safe Boot)
http://support.apple.com/kb/TS2570
Another option might be to download the standalone from Apple Downloads on another Mac and try installing it in Firewire Target Disk Mode to the Mac that was interrupted during the update.
http://support.apple.com/kb/HT1661

Macbook starts up with chime then white screen with grey apple logo and spinning gear appears and continues to spin

Help, Turned on MacBook Pro this morning and just get a white screen with grey apple logo and spinning gear. Cannot access desktop.

Computer starts up in Safe boot by holding down the shift button. But when I go to restart the same thing happens. What should I do?

My iphone 4 does not ring but it does vibrate. None of the ringtones work.

My iphone 4 does not ring but it does vibrate. None of the ringtones work. This problem started suddenly. Any answers?

I hate to ask the obvious question, but is your ringer switch turned off on the side of your phone?

HT3964 I am not able to reboot my Mac desktop. When I switch on the Mac, I get a white screen with the Apple logo and the little wheel below that goes round and round but the computer refuses to boot.

Hi, I am not able to reboot my Mac desktop.
When I switch on the Mac, I get a white screen with the Apple logo and the little rotating circle.
The system refuses to boot.
What can I do?
Marcus

We need to get you moved. This forum is for mini-tower Macs built between 1998 and 2005 and doesn;t get as much traffic ("eyeballs on the problem") as the forums for newer Macs.
Please do "About this Mac" from you Apple menu and tell us what that says for "processor" and Mac OS version. Looks like this:
or this for later Mac OS versions:
With that we can figure out which of the two iMac forums you need and get the Hosts to move your post.

My iPad wont turn on, its black screen then i press home power buttons together and white screen with black apple logo come out after 5 seconds black "lighten" screen comes out and its stuck just like that! Whats the problem?

HI
this happened today suddenly while i was working on my iPad it kicked my out of the app that i was using then white screen with black apple logo came out, i thought it was an ordinary thing cause this happens all the time with me, but this time it refused to turn on! After the white screen with the black logo vanished i wad waiting for my lock screen but no, a black screen showed up just like that! And could tell it was black "lighten" screen i tried more than 10 times to do the home+power thing but it wont work, whats wrong with my ipad!

If the battery is completely drained it may take some time while on the charger before the iPad responds. Plug the iPad into the charger that came with it and plug that into a good wall outlet. Wait one hour. Then reset your device. Press and hold the Home and Sleep buttons simultaneously until the Apple logo appears. Let go of the buttons and let the device restart. If the iPad restarts let it continue to charge until the battery is 100%. If it doesn't start up make an appointment at an Apple Store to have your device examined by a technician. Or contact Apple Support. They will examine your iPad and explain your options.

My MacBook Air will not turn on. I get a white screen with the apple logo and a spinning star that just does that for hours

My MacBook Air will not turn on. I get a white screen with the apple logo and a spinning star (search icon). It will spin for hours and never go away unless I power off.

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
To restart an unresponsive computer, press and hold the power button for a few seconds until the power shuts off, then release, wait a few more seconds, and press it again briefly.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If a desktop Mac hangs at a plain gray screen with a movable cursor, the keyboard may not be recognized. Press and hold the button on the side of an Apple wireless keyboard to make it discoverable. If need be, replace or recharge the batteries. If you're using a USB keyboard connected to a hub, connect it to a built-in port.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

HT4061 I have an iphone 5s, does not boot, blinking white screen with black logo, when trying itunes restore from mac and pc, error code 4013 which is usb error, any ideas?

I have an iphone 5s, does not boot, blinking white screen with black logo, when trying itunes restore from mac and pc, error code 4013 which is usb error, any ideas? Does a totally dead battery have that effect? I have had it plugged in to a computer overnight, but maybe does not charge when totally dead?
Please help, thanks in advance all1

Hi eggroll77,
Welcome to Apple Support Communities.
That alert codes does suggest there is a USB related issue. If you haven’t already, try the troubleshooting suggestions in the article linked below.
iOS: Restore errors 4005, 4013, and 4014
I hope this helps.
-Jason

HT1553 I did the back up as instructed... Installed a larger hard drive and followed the restore instructions... Now I get a white screen with a folder icon and blinking question mark. When trying to set startup with new drive I get a bless tool error...

I did the back up as instructed... Installed a larger hard drive and followed the restore instructions... Now I get a white screen with a folder icon and blinking question mark. When trying to set startup with new drive I get a bless tool error... Help!!

If you have installed a new hard drive , you will need to have formatted it in Disk Utility correctly. This may explain your problem.
Boot into your 10.6 Install disk again at the top menubar > Utilities > select Disk utility and in there select your new hard drive, and select the tab Erase and choose to make the format as Mac OS Extended Journaled. When that is finished look in the main window to make sure that the partition map scheme says GUID Partition Table.
Now go to the Restore tab and reinstall from your backup.

My iphone 6 wont go past the start up screen (white screen with black apple) iv treid restoring it on itunes but it disconects its self half way through

my iphone 6 wont go past the start up screen (white screen with black apple) iv treid restoring it on itunes but it disconects its self half way through. what can I do

Did you try to use recovery mode, explained in this article?
If you can't update or restore your iOS device
If it does not work after that, you'll have to get it serviced:
iPhone - Contact Support - Apple Support

My 1st generation Ipod touch won't turn on at all and whenever I press the buttons to reset it all I get is a white screen, or a white screen with black lines across.

My 1st generation Ipod touch won't turn on at all and whenever I press the buttons to reset it all I get is a white screen, or a white screen with black lines across.Help pleaseeeeee!

You can work through the five 5 R's of troubleshooting to rule out the possibility of corrupted software.
http://www.apple.com/support/ipod/five_rs/
It might also be a good idea to let the iPod's battery fully drain. Then charge it back up and restore it once more in iTunes.
Otherwise, it's likely a hardware issue with the iPod's LCD display, meaning you'll need to take or send your iPod in for service either via Apple or a third party repair service. Here is Apple's repair pricing.
http://www.apple.com/support/ipod/service/prices/
Note that they don't actually repair the device, but exchange it for one of the same generation, model, and capacity. A third party service will actually replace the damaged part for a little less. Google "iPod screen repair" and you should get a number of results to work with.
B-rock

HT5654 my iphone 5 fell did not break but went completely black and non responsive. When I plug it to the computer I get a white screen with black apple. When I push both the Top and Homne buttons simultaneously I get the charger picture plug end plus arr

Similar Messages

Maybe you are looking for