I am creating box for two coloums in sap script

Question

hi,
i am creating box for two coloums
when i am creating box for this two coloums this box is displaying from the top.
when i am decreasing this hight it is decreasing from the buttom of the window
i want to decrease from the top of window
can u explan plz
this requirement
plzz

Answer 1

see this:
BOX Command
Syntax
/: BOX [XPOS] [YPOS] [WIDTH] [HEIGHT] [FRAME] [INTENSITY]
Effect: draws a box of the specified size at the specified position.
Parameters: For each of XPOS, YPOS, WIDTH, HEIGHT, and FRAME, you must specify both a measurement and a unit of measurement. Specify the INTENSITY parameter as a percentage between 0 and 100.
XPOS, YPOS
Upper left corner of the box, relative to the values of the POSITION command.
Default: Values specified in the POSITION command.
The following calculation is performed internally to determine the absolute output position of a box on the page:
X(abs) = XORIGIN + XPOS
Y(abs) = YORIGIN + YPOS
WIDTH
Width of the box. Default: WIDTH value of the SIZE command.
HEIGHT
Height of the box. Default: HEIGHT value of the SIZE command.
FRAME
Thickness of frame.
Default: 0 (no frame).
INTENSITY
Grayscale of box contents as %.
Default: 100 (full black)
Measurements: You must specify decimal numbers as literal values (like ABAP numeric constants) by enclosing them in inverted commas. Use the period as the decimal point character. See also the examples listed below.
Units of measurement: The following units of measurement may be used:
TW (twip)
PT (point)
IN (inch)
MM (millimeter)
CM (centimeter)
LN (line)
CH (character).
The following conversion factors apply:
1 TW = 1/20 PT
1 PT = 1/72 IN
1 IN = 2.54 CM
1 CM = 10 MM
1 CH = height of a character relative to the CPI specification in the form header
1 LN = height of a line relative to the LPI specification in the form header
/: BOX FRAME 10 TW
Draws a frame around the current window with a frame thickness of 10 TW (= 0.5 PT).
/: BOX INTENSITY 10
Fills the window background with shading having a gray scale of 10 %.
/: BOX HEIGHT 0 TW FRAME 10 TW
Draws a horizontal line across the complete top edge of the window.
/: BOX WIDTH 0 TW FRAME 10 TW
Draws a vertical line along the complete height of the left hand edge of the window.
/: BOX WIDTH '17.5' CM HEIGHT 1 CM FRAME 10 TW INTENSITY 15
/: BOX WIDTH '17.5' CM HEIGHT '13.5' CM FRAME 10 TW
/: BOX XPOS '10.0' CM WIDTH 0 TW HEIGHT '13.5' CM FRAME 10 TW
/: BOX XPOS '13.5' CM WIDTH 0 TW HEIGHT '13.5' CM FRAME 10 TW
Draws two rectangles and two lines to construct a table of three columns with a highlighted heading section.
POSITION Command
Syntax
/: POSITION [XORIGIN] [YORIGIN] [WINDOW] [PAGE]
Effect: Sets the origin for the coordinate system used by the XPOS and YPOS parameters of the BOX command. When a window is first started, the POSITION value is set to refer to the upper left corner of the window (default setting).
Parameters: If a parameter value does not have a leading sign, then its value is interpreted as an absolute value, in other words, as a value that specifies an offset from the upper left corner of the output page. If a parameter value is specified with a leading sign, then the new value of the parameter is calculated relative to the old value. If one of the parameter specifications is missing, then no change is made to this parameter.
XORIGIN, YORIGIN
Origin of the coordinate system.
WINDOW
Sets the values for the left and upper edges to match those of the current window (default setting).
PAGE
Sets the values for the left and upper edges to match those of the current output page (XORIGIN = 0 cm, YORIGIN = 0 cm).
/: POSITION WINDOW
Sets the origin for the coordinate system to the upper left corner of the window.
/: POSITION XORIGIN 2 CM YORIGIN '2.5 CM'
Sets the origin for the coordinate system to a point 2 cm from the left edge and 2.5 cm from the upper edge of the output page.
/: POSITION XORIGIN '-1.5' CM YORIGIN -1 CM
Shifts the origin for the coordinates 1.5 cm to the left and 1 cm up.
Pre-Setting BOX Position Arguments
You can use the POSITION and SIZE commands to preset some arguments in the BOX command. POSITION presets the start point (upper left corner) of a box or line. SIZE specifies the width and height of a box.
You can use POSITION and SIZE to preset arguments, but you can also set the start point and size arguments of a box or line directly in the BOX command.
By default, if no positioning is specified, the upper left corner of a box or halftone or the top of a line is aligned with current SAPscript window. That is, the upper left corner of the box, halftone, or line starts at the upper left corner of the current window in the active form. By default, the height and width of a box are set to the height and width of the current window.
Use POSITION and SIZE to preset the arguments in a BOX command in the following situations:
The BOX command exceeds the 132-character (1 line in SAPscript) length limitation if you specify all arguments directly in the command. You may exceed this length limit if, for example, you use symbols in a command.
By pre-setting arguments with POSITION and SIZE, you can work around the limitation on the length of a command. You do not need to specify the preset arguments in the BOX command.
You want to use the enhanced capabilities of POSITION for adjusting the starting point of a box or line.
With BOX, you can specify an offset for the starting point only as a whole number (non-negative integer). This command would print a box starting 1 CM to the right and 1 CM down from the left upper corner of a window:
/: BOX XPOS '1' CM YPOS '1' CM
With POSITION; you can adjust the position of a line or box relative to a window much more precisely. In the POSITION command, you can specify positive and negative offsets and use non-integer numbers.
Example: The commands shown below position a box slightly to the left and slightly above a window. This leaves a margin between the edge of the box and the text in the window.
/: POSITION XORIGIN '-.2' CM YORIGIN '-.2' CM
/: SIZE WIDTH '.2' CM HEIGHT '.2' CM
/: BOX FRAME 10 TW
(Note that the box must be enlarged to accommodate the shift. If it is not enlarged, then it will not cover all of the window.)
You can also use POSITION to set the starting point to the upper left corner of the active page format. Example: POSITION PAGE moves the starting point from the active window to the active page format.
You want to use the relative sizing capabilities of SIZE to adjust the size of a box, line, or halftone.
With BOX, you can make only absolute size specifications. BOX HEIGHT, for example, overrides the default height setting to the height of the current window.
With SIZE, you can adjust the size of a box or a line with respect to its previously-set dimensions. The following commands would, for example, draw a frame 1 CM in from the margins of the paper:
/: POSITION PAGE
/: POSITION XORIGIN 1 CM YORIGIN 1 CM
/: SIZE PAGE
/: SIZE HEIGHT '-2' CM WIDTH '-2' CM
REWARD IF HELPFUL