I am in mavericks disk utility recovery mode as my mac book will not boot up & stays only on the grey apple screen. When I verify the disk I get open error5 :input /output error on Syst stuck on 1 minute pouring out over 50 error messages & still counting

I am in Mavericks disk utility recovery mode as my mac book pro will not boot up & stays on the Apple grey screen . When I verify disk permissions I get
Open error 5:"input/ output error" on syst with over 50 of this messages & still counting . Disk Utility says 1 minute
But this has been going on for over 10 mins .
I can not verify disk or repair disk .
I have tried to reinstall mavericks operating system but it says my hard drive is locked which is very strange .
Does anyone know what is going on here ?
My system looks like it has been totally corrupted . Thanks Andrew

Could be. The "lock" isn't actually looking for a password.
WARNING: This will completely erase the ENTIRE hard drive.
What you would need to do is boot to recovery > disk utility > select the MAIN drive on the left side > partition > change partition layout from CURRENT to 1 PARTITION > ensure on the right side it says Format : Mac OSX Extended (Journaled) then push APPLY.
Then if it will allow us, close the windows until you see the 4 options popup again and select "Reinstall Mac OS X" select the Mac HD and you should be good to go!

Similar Messages

Ok guys i need help my ipod touch froze during an update now i put it inot the recovery mode or dfu and it will not reset itself at all it comes up with an error code and says this ipod cannot reset now does anyone have any ideas of what to do with it

ok guys i need help anyone with my ipod it froze during an update now it will not work at all i ahve put it into the recovery mode or dfu and it will not reset it self it comes up with an error message 1603 the number is and says the ipod cannot be reset anyone please help me i have tryed everything googled you tubed everything

Error 1604
This error is often related to USB timing. Try changing USB ports, using a different dock connector to USB cable, and other available USB troubleshooting steps (troubleshooting USB connections. If you are using a dock, bypass it and connect directly to the white Apple USB dock connector cable. If the issue persists on a known-good computer, the device may need service.
If the issue is not resolved by USB isolation troubleshooting, and another computer is not available, try these steps to resolve the issue:
Connect the device to iTunes, confirm that the device is in Recovery Mode. If it's not in Recovery Mode,put it into Recovery Mode.
Restore and wait for the error.
When prompted, click OK.
Close and reopen iTunes while the device remains connected.
The device should now be recognized in Recovery Mode again.
Try to restore again.
If the steps above do not resolve the issue, try restoring using a known-good USB cable, computer, and network connection.
Error 1600, 1601, 1602
Error 1603
Follow the steps listed above for Error 1604. Also, discard the .ipsw file, open iTunes and attempt to download the update again. See the steps under Advanced Steps > Rename, move, or delete the iOS software file (.ipsw) below for file locations.If you do not want to remove the IPSW in the original user, try restoring in a new administrator user. If the issue remains, Eliminate third-party security software conflicts.

My 2009 iMac gets stuck on the grey Apple logo when booting up. It boots correctly when in safe mode. I have tried erasing the HD and re-installing from a USB installer. It says the install is complete, but after restarting it gets stuck on the Apple log

My late 2009 27" iMac gets stuck on the grey Apple logo when booting up. It boots correctly when in safe mode. I have tried erasing the HD and re-installing from a USB installer. It says the install is complete, but after restarting it gets stuck on the Apple logo again. This could possibly be an HD failure, but then why does Safe Mode still work and the USB install not work? Any ideas?

1. This procedure is a diagnostic test. It changes nothing, for better or worse, and therefore will not, in itself, solve the problem. But with the aid of the test results, the solution may take a few minutes, instead of hours or days.
Don't be put off merely by the seeming complexity of these instructions. The process is much less complicated than the description. You do harder tasks with the computer all the time.
2. If you don't already have a current backup, back up all data before doing anything else. The backup is necessary on general principle, not because of anything in the test procedure. Backup is always a must, and when you're having any kind of trouble with the computer, you may be at higher than usual risk of losing data, whether you follow these instructions or not.
There are ways to back up a computer that isn't fully functional. Ask if you need guidance.
3. Below are instructions to run a UNIX shell script, a type of program. All it does is to collect information about the state of the computer. That information goes nowhere unless you choose to share it. However, you should be cautious about running any kind of program (not just a shell script) at the behest of a stranger. If you have doubts, search this site for other discussions in which this procedure has been followed without any report of ill effects. If you can't satisfy yourself that the instructions are safe, don't follow them. Ask for other options.
Here's a summary of what you need to do, if you choose to proceed:
☞ Copy a line of text in this window to the Clipboard.
☞ Paste into the window of another application.
☞ Wait for the test to run. It usually takes a few minutes.
☞ Paste the results, which will have been copied automatically, back into a reply on this page.
The sequence is: copy, paste, wait, paste again. You don't need to copy a second time. Details follow.
4. You may have started the computer in "safe" mode. Preferably, these steps should be taken in “normal” mode, under the conditions in which the problem is reproduced. If the system is now in safe mode and works well enough in normal mode to run the test, restart as usual. If you can only test in safe mode, do that.
5. If you have more than one user, and the one affected by the problem is not an administrator, then please run the test twice: once while logged in as the affected user, and once as an administrator. The results may be different. The user that is created automatically on a new computer when you start it for the first time is an administrator. If you can't log in as an administrator, test as the affected user. Most personal Macs have only one user, and in that case this section doesn’t apply. Don't log in as root.
6. The script is a single long line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, though you may not see all of it in the browser window, and you can then copy it. If you try to select the line by dragging across the part you can see, you won't get all of it.
Triple-click anywhere in the line of text below on this page to select it:
PATH=/usr/bin:/bin:/usr/sbin:/sbin:/usr/libexec;clear;cd;p=(Software Hardware Memory Diagnostics Power FireWire Thunderbolt USB Fonts 51 4 1000 25 5120 KiB/s 1024 85 \\b%% 20480 1 MB/s 25000 ports 'com.autodesk.AutoCad com.evenflow.dropbox com.google.GoogleDrive' DYLD_INSERT_LIBRARIES\ DYLD_LIBRARY_PATH -86 ` route -n get default|awk '/e:/{print $2}' ` 25 N\\/A down up 102400 25600 recvfrom sendto CFBundleIdentifier 25 25 25 1000 MB );N5=${#p[@]};p[N5]=` networksetup -listnetworkserviceorder|awk ' NR>1 { sub(/^$[0-9]+$ /,"");n=$0;getline;} $NF=="'${p[26]}')" { sub(/.$/,"",$NF);print n;exit;} ' `;f=('\n%s: %s\n' '\n%s\n\n%s\n' '\nRAM details\n%s\n' %s\ %s '%s\n\t(%s)\n' );S0() { echo ' { q=$NF+0;$NF="";u=$(NF-1);$(NF-1)="";gsub(/^ +| +$/,"");if(q>='${p[$1]}') printf("%s (UID %s) is using %s '${p[$2]}'",$0,u,q);} ';};s=(' /^ *$|CSConfigDot/d;s/^ */ /;s/[-0-9A-Fa-f]{22,}/UUID/g;s/(ochat)\.[^.]+(\..+)/\1\2/;/Shared/!s/\/Users\/[^/]+/~/g ' ' s/^ +//;5p;6p;8p;12p;' ' {sub(/^ +/,"")};NR==6;NR==13&&$2<'${p[10]} ' 1s/://;3,6d;/[my].+:/d;s/^ {4}//;H;${ g;s/\n$//;/s: [^EO]|x([^08]|02[^F]|8[^0])/p;} ' ' 5h;6{ H;g;/P/!p;} ' ' ($1~/^Cy/&&$3>'${p[11]}')||($1~/^Cond/&&$2!~/^N/) ' ' /:$/{ N;/:.+:/d;s/ *://;b0'$'\n'' };/^ *(V.+ [0N]|Man).+ /{ s/ 0x.... //;s/[()]//g;s/(.+: )(.+)/ (\2)/;H;};$b0'$'\n'' d;:0'$'\n'' x;s/\n\n//;/Apple[ ,]|Intel|SMSC/d;s/\n.*//;/\)$/p;' ' s/^.*C/C/;H;${ g;/No th|pms/!p;} ' '/= [^GO]/p' '{$1=""};1' ' /Of/!{ s/^.+is |\.//g;p;} ' ' $0&&!/ / { n++;print;} END { if(n<200) print "com.apple.";} ' ' $3~/[0-9]:[0-9]{2}$/ { gsub(/:[0-9:a-f]{14}/,"");} { print|"tail -n'${p[12]}'";} ' ' NR==2&&$4<='${p[13]}' { print $4;} ' ' END { $2/=256;if($2>='${p[15]}') print int($2) } ' ' NR!=13{next};{sub(/[+-]$/,"",$NF)};'"`S0 21 22`" 'NR!=2{next}'"`S0 37 17`" ' NR!=5||$8!~/[RW]/{next};{ $(NF-1)=$1;$NF=int($NF/10000000);for(i=1;i<=3;i++){$i="";$(NF-1-i)="";};};'"`S0 19 20`" 's:^:/:p' '/\.kext\/(Contents\/)?Info\.plist$/p' 's/^.{52}(.+) <.+/\1/p' ' /Launch[AD].+\.plist$/ { n++;print;} END { if(n<200) print "/System/";} ' '/\.xpc\/(Contents\/)?Info\.plist$/p' ' NR>1&&!/0x|\.[0-9]+$|com\.apple\.launchctl\.(Aqua|Background|System)$/ { print $3;} ' ' /\.(framew|lproj)|\):/d;/plist:|:.+(Mach|scrip)/s/:[^:]+//p ' '/root/p' ' !/\/Contents\/.+\/Contents|Applic|Autom|Frameworks/&&/Lib.+\/Info.plist$/ { n++;print;} END { if(n<1000) print "/System/";} ' '/^\/usr\/lib\/.+dylib$/p' ' /Temp|emac/d;/(etc|Preferences)\//s/^\.\/[^/]+//p;' ' /\/(Contents\/.+\/Contents|Frameworks)\/|\.wdgt\/.+\.([bw]|plu)/d;p;' 's/\/(Contents\/)?Info.plist$//;p' ' { gsub("^| ","||kMDItem'${p[35]}'=");sub("^.."," ") };1 ' p '{print $3"\t"$1}' 's/\'$'\t''.+//p' 's/1/On/p' '/Prox.+: [^0]/p' '$2>'${p[9]}'{$2=$2-1;print}' ' BEGIN { i="'${p[26]}'";M1='${p[16]}';M2='${p[18]}';M3='${p[31]}';M4='${p[32]}';} !/^A/ { next;} /%/ { getline;if($5<M1) a="user "$2"%, system "$4"%";} /disk0/&&$4>M2 { b=$3" ops/s, "$4" blocks/s";} $2==i { if(c) { d=$3+$4+$5+$6;next;};if($4>M3||$6>M4) c=int($4/1024)" in, "int($6/1024)" out";} END { if(a) print "CPU: "a;if(b) print "I/O: "b;if(c) print "Net: "c" (KiB/s)";if(d) print "Net errors: "d" packets/s";} ' ' /r\[0\] /&&$NF!~/^1(0|72\.(1[6-9]|2[0-9]|3[0-1])|92\.168)\./ { print $NF;exit;} ' ' !/^T/ { printf "(static)";exit;} ' '/apsd|OpenD/!s/:.+//p' ' (/k:/&&$3!~/(255\.){3}0/ )||(/v6:/&&$2!~/A/ ) ' ' $1~"lR"&&$2<='${p[25]}';$1~"li"&&$3!~"wpa2";' ' BEGIN { FS=":";} { n=split($3,a,".");sub(/_2[01].+/,"",$3);print $2" "$3" "a[n]" "$1;b=b$1;} END { if(b) print("\n\t* Code injection");} ' ' NR!=4{next} {$NF/=10240} '"`S0 27 14`" ' END { if($3~/[0-9]/)print$3;} ' ' BEGIN { L='${p[36]}';} !/^[[:space:]]*(#.*)?$/ { l++;if(l<=L) f=f"\n "$0;} END { F=FILENAME;if(!F) exit;if(!f) f="\n [N/A]";"file -b "F|getline T;if(T!~/^(AS.+ (En.+ )?text$|POSIX sh.+ text ex)/) F=F" ("T")";printf("\nContents of %s\n%s\n",F,f);if(l>L) printf("\n ...and %s more line(s)\n",l-L);} ' ' /^ +[NP].+ =/h;/^( +D.+[{]|[}])/{ g;s/.+= //p;};' ' /^ +B/{ s/.+= |(-[0-9]+)?\.s.+//g;p;} ' ' END{print NR} ' ' /id: N|te: Y/{i++} END{print i} ' ' / /{$0="'"${p[28]}"'"};1;' '/ en/!s/\.//p' ' NR!=13{next};{sub(/[+-M]$/,"",$NF)};'"`S0 39 40`" ' $10~/$L/&&$9!~"localhost" { sub(/.+:/,"",$9);print $1": "$9;} ' '/^ +r/s/.+"(.+)".+/\1/p' 's/(.+\.wdgt)\/(Contents\/)?Info\.plist$/\1/p' 's/^.+\/(.+)\.wdgt$/\1/p' 's/0/Off/p' );c1=(system_profiler pmset\ -g nvram fdesetup find syslog df vm_stat sar ps sudo\ crontab sudo\ iotop top pkgutil PlistBuddy whoami cksum kextstat launchctl sudo\ launchctl crontab 'sudo defaults read' stat lsbom mdfind ' for i in ${p[24]};do ${c1[18]} ${c2[27]} $i;done;' defaults\ read scutil sudo\ dtrace sudo\ profiles sed\ -En awk /S*/*/P*/*/*/C*/*/airport networksetup mdutil sudo\ lsof test );c2=(com.apple.loginwindow\ LoginHook '-c Print /L*/P*/loginw*' '-c Print L*/P*/*loginit*' '-c Print L*/Saf*/*/E*.plist' '~ $TMPDIR.. \( -flags +sappnd,schg,uappnd,uchg -o ! -user $UID -o ! -perm -600 $' '.??* -path .Trash -prune -o -type d -name *.app -print -prune' '-c Print\ :'${p[35]}' 2>&1' '-c Print\ :Label 2>&1|head -1' '{/,}L*/{Con,Pref}* -type f ! -size 0 -name *.plist -exec plutil -s {} \;' "-f'%N: %l' Desktop L*/Keyc*" therm sysload boot-args status " -F '\$Time \$Message' -k Sender kernel -k Message Req 'Beac|caug|dead[^bl]|FAIL|fail|GPU |hfs: Ru|inval|jnl:|last value [1-9]|n Cause: -|NVDA$|pagin|proc: t|Roamed|rror|ssert|Thrott|tim(ed? ?|ing )o|WARN' -k Message Rne 'Goog|ksadm|SMC:' -o -k Sender fseventsd -k Message Req 'SL' " '-du -n DEV -n EDEV 1 10' 'acrx -o comm,ruid,%cpu' '-t1 10 1' '-f -pfc /var/db/r*/com.apple.*.{BS,Bas,Es,OSXU,Rem,up}*.bom' '{/,}L*/Lo*/Diag* -type f -regex .\*[cgh] ! -name *ag \( -exec grep -lq "^Thread c" {} \; -exec printf \* \; -o -true $ -execdir stat -f:%Sc:%N -t%F {} \;|sort -t: -k2 |tail -n'${p[38]} '-L {/{S*/,},}L*/Lau* -type f' '-L /{S*/,}L*/StartupItems -type f -exec file {} +' '-L /S*/L*/{C*/Sec*A,E}* {/,}L*/{A*d,Ca*/*/Ex,Compon,Ex,In,iTu,Keyb,Mail/B,P*P,Qu*T,Scripti,Sec,Servi,Spo,Widg}* -type f -name Info.plist' '/usr/lib -type f -name *.dylib' `awk "${s[31]}"<<<${p[23]}` "/e*/{auto,{cron,fs}tab,hosts,{[lp],sy}*.conf,pam.d,ssh{,d}_config,*.local} {,/usr/local}/etc/periodic/*/* /L*/P*{,/*}/com.a*.{Bo,sec*.ap}*t .launchd.conf" list getenv /Library/Preferences/com.apple.alf\ globalstate --proxy '-n get default' -I --dns -getdnsservers\ "${p[N5]}" -getinfo\ "${p[N5]}" -P -m\ / '' -n1 '-R -l1 -n1 -o prt -stats command,uid,prt' '--regexp --only-files --files com.apple.pkg.*|sort|uniq' -kl -l -s\ / '-R -l1 -n1 -o mem -stats command,uid,mem' -i4TCP:0-1023 com.apple.dashboard\ layer-gadgets '-d /L*/Mana*/$USER&&echo On' '-app Safari WebKitDNSPrefetchingEnabled' );N1=${#c2[@]};for j in {0..8};do c2[N1+j]=SP${p[j]}DataType;done;N2=${#c2[@]};for j in 0 1;do c2[N2+j]="-n ' syscall::'${p[33+j]}':return { @out[execname,uid]=sum(arg0) } tick-10sec { trunc(@out,1);exit(0);} '";done;l=(Restricted\ files Hidden\ apps 'Elapsed time (s)' POST Battery Safari\ extensions Bad\ plists 'High file counts' User Heat System\ load boot\ args FileVault Diagnostic\ reports Log 'Free space (MiB)' 'Swap (MiB)' Activity 'CPU per process' Login\ hook 'I/O per process' Mach\ ports kexts Daemons Agents launchd Startup\ items Admin\ access Root\ access Bundles dylibs Apps Font\ issues Inserted\ dylibs Firewall Proxies DNS TCP/IP Wi-Fi Profiles Root\ crontab User\ crontab 'Global login items' 'User login items' Spotlight Memory Listeners Widgets Parental\ Controls Prefetching );N3=${#l[@]};for i in 0 1 2;do l[N3+i]=${p[5+i]};done;N4=${#l[@]};for j in 0 1;do l[N4+j]="Current ${p[29+j]}stream data";done;A0() { id -G|grep -qw 80;v[1]=$?;((v[1]==0))&&sudo true;v[2]=$?;v[3]=`date +%s`;clear >&-;date '+Start time: %T %D%n';};for i in 0 1;do eval ' A'$((1+i))'() { v=` eval "${c1[$1]} ${c2[$2]}"|'${c1[30+i]}' "${s[$3]}" `;[[ "$v" ]];};A'$((3+i))'() { v=` while read i;do [[ "$i" ]]&&eval "${c1[$1]} ${c2[$2]}" \"$i\"|'${c1[30+i]}' "${s[$3]}";done<<<"${v[$4]}" `;[[ "$v" ]];};A'$((5+i))'() { v=` while read i;do '${c1[30+i]}' "${s[$1]}" "$i";done<<<"${v[$2]}" `;[[ "$v" ]];};';done;A7(){ v=$((`date +%s`-v[3]));};B2(){ v[$1]="$v";};for i in 0 1;do eval ' B'$i'() { v=;((v['$((i+1))']==0))||{ v=No;false;};};B'$((3+i))'() { v[$2]=`'${c1[30+i]}' "${s[$3]}"<<<"${v[$1]}"`;} ';done;B5(){ v[$1]="${v[$1]}"$'\n'"${v[$2]}";};B6() { v=` paste -d: <(printf "${v[$1]}") <(printf "${v[$2]}")|awk -F: ' {printf("'"${f[$3]}"'",$1,$2)} ' `;};B7(){ v=`grep -Fv "${v[$1]}"<<<"$v"`;};C0(){ [[ "$v" ]]&&echo "$v";};C1() { [[ "$v" ]]&&printf "${f[$1]}" "${l[$2]}" "$v";};C2() { v=`echo $v`;[[ "$v" != 0 ]]&&C1 0 $1;};C3() { v=`sed -E "$s"<<<"$v"`&&C1 1 $1;};for i in 1 2;do for j in 2 3;do eval D$i$j'(){ A'$i' $1 $2 $3; C'$j' $4;};';done;done;{ A0;A2 0 $((N1+1)) 2;C0;A1 0 $N1 1;C0;B0;C2 27;B0&&! B1&&C2 28;D12 15 37 25 8;A1 0 $((N1+2)) 3;C0;D13 0 $((N1+3)) 4 3;D23 0 $((N1+4)) 5 4;for i in 0 1 2;do D13 0 $((N1+5+i)) 6 $((N3+i));done;D13 1 10 7 9;D13 1 11 8 10;D22 2 12 9 11;D12 3 13 10 12;D23 4 19 44 13;D23 5 14 12 14;D22 6 36 13 15;D22 7 37 14 16;D23 8 15 38 17;D22 9 16 16 18;B1&&{ D22 11 17 17 20;for i in 0 1;do D22 28 $((N2+i)) 45 $((N4+i));done;};D22 12 44 54 45;D22 12 39 15 21;A1 13 40 18;B2 4;B3 4 0 19;A3 14 6 32 0;B4 0 5 11;A1 17 41 20;B7 5;C3 22;B4 4 6 21;A3 14 7 32 6;B4 0 7 11;B3 4 0 22;A3 14 6 32 0;B4 0 8 11;B5 7 8;B1&&{ A2 19 26 23;B7 7;C3 23;};A2 18 26 23;B7 7;C3 24;A2 4 20 21;B7 6;B2 9;A4 14 7 52 9;B2 10;B6 9 10 4;C3 25;D13 4 21 24 26;B4 4 12 26;B3 4 13 27;A1 4 22 29;B7 12;B2 14;A4 14 6 52 14;B2 15;B6 14 15 4;B3 0 0 30;C3 29;A1 4 23 27;B7 13;C3 30;D13 24 24 32 31;D13 25 37 32 33;A1 23 18 28;B2 16;A2 16 25 33;B7 16;B3 0 0 34;B2 21;A6 47 21&&C0;B1&&{ D13 21 0 32 19;D13 10 42 32 40;D22 29 35 46 39;};D23 14 1 48 42;D12 34 43 53 44;D22 0 $((N1+8)) 51 32;D13 4 8 41 6;D12 26 28 35 34;D13 27 29 36 35;A2 27 32 39&&{ B2 19;A2 33 33 40;B2 20;B6 19 20 3;};C2 36;D23 33 34 42 37;B1&&D23 35 45 55 46;D23 32 31 43 38;D12 36 47 32 48;D13 20 42 32 41;D13 14 2 48 43;D13 4 5 32 1;D22 4 4 50 0;D13 14 3 49 5;D12 26 48 59 49;B3 4 22 57;A1 26 46 56;B7 22;B3 0 0 58;C3 47;D23 22 9 37 7;A7;C2 2;} 2>/dev/null|pbcopy;exit 2>&-
Copy the selected text to the Clipboard by pressing the key combination command-C.
7. Launch the built-in Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Click anywhere in the Terminal window and paste by pressing command-V. The text you pasted should vanish immediately. If it doesn't, press the return key.
8. If you see an error message in the Terminal window such as "syntax error," enter
exec bash
and press return. Then paste the script again.
9. If you're logged in as an administrator, you'll be prompted for your login password. Nothing will be displayed when you type it. You will not see the usual dots in place of typed characters. Make sure caps lock is off. Type carefully and then press return. You may get a one-time warning to be careful. If you make three failed attempts to enter the password, the test will run anyway, but it will produce less information. In most cases, the difference is not important. If you don't know the password, or if you prefer not to enter it, press the key combination control-C or just press return three times at the password prompt. Again, the script will still run.
If you're not logged in as an administrator, you won't be prompted for a password. The test will still run. It just won't do anything that requires administrator privileges.
10. The test may take a few minutes to run, depending on how many files you have and the speed of the computer. A computer that's abnormally slow may take longer to run the test. While it's running, there will be nothing in the Terminal window and no indication of progress. Wait for the line
[Process completed]
to appear. If you don't see it within half an hour or so, the test probably won't complete in a reasonable time. In that case, close the Terminal window and report the results. No harm will be done.
11. When the test is complete, quit Terminal. The results will have been copied to the Clipboard automatically. They are not shown in the Terminal window. Please don't copy anything from there. All you have to do is start a reply to this comment and then paste by pressing command-V again.
At the top of the results, there will be a line that begins with "Model Identifier." If you don't see that, but instead see a mass of gibberish, you didn't wait for the "Process completed" message to appear in the Terminal window. Please wait for it and try again.
If any private information, such as your name or email address, appears in the results, anonymize it before posting. Usually that won't be necessary.
12. When you post the results, you might see the message, "You have included content in your post that is not permitted." It means that the forum software has misidentified something in the post as a violation of the rules. If that happens, please post the test results on Pastebin, then post a link here to the page you created.
Note: This is a public forum, and others may give you advice based on the results of the test. They speak only for themselves, and I don't necessarily agree with them.
Copyright © 2014 by Linc Davis. As the sole author of this work, I reserve all rights to it except as provided in the Use Agreement for the Apple Support Communities website ("ASC"). Readers of ASC may copy it for their own personal use. Neither the whole nor any part may be redistributed.

I can't get past the grey apple screen using mavericks

I can't get past the grey apple screen trying to boot up with Mavericks. I had been using Mavericks for about a month (only had issues of freezing occasionally). I read in one of the posts here that I should try holding command R down when booting. I did now I just get a grey screen without the apple. Any advise?
I have a Mac Mini

Hello ther cnickers,
It sounds like the initial install of Mavericks went ok, and you have been using it for a while, but now cannot boot to your desktop and are stuck at a gray screen with an Apple logo. I would recommend a couple of things here:
First, try performing a Safe Boot to see if that will load up for you. If so then leave Safe Boot and restart from the Apple menu to try and get to your deskop:
To start up into Safe Mode (to Safe Boot), follow these steps.
Be sure your Mac is shut down.
Press the power button.
Immediately after you hear the startup tone, hold the Shift key.
The Shift key should be held as soon as possible after the startup tone, but not before the tone.
Release the Shift key when you see the gray Apple logo and the progress indicator (looks like a spinning gear).
After the logo appears, you should see a progress bar during startup. This indicates that your computer is performing a directory check as part of Safe Mode.
To leave Safe Mode, restart your computer without holding any keys during startup.
From: Mac OS X: What is Safe Boot, Safe Mode?
http://support.apple.com/kb/ht1564
If that works fine, I would next also verify and repair your disk if needed.
Disk Utility 12.x: Repair a disk
http://support.apple.com/kb/PH5836
Print this help page so you can refer to it later. (You don’t have access to Disk Utility Help when you restart up your computer in the next step.)In the Disk Utility Help window, choose Print from the Action pop-up menu (looks like a gear).
Choose Apple menu > Restart. Hold down the Command (⌘) and R keys as your computer restarts.When you see a white screen with an Apple logo in the middle, you can release the keys.
Click Disk Utility, and then click Continue.
In the list at the left, select the item you want to repair. (Be sure to select an item that’s indented to the right in the list, not an item at the far left.)
Click First Aid.
If Disk Utility tells you the disk is about to fail, back it up and replace it. You can’t repair it.
Click Repair Disk.If Disk Utility reports that the disk appears to be OK or has been repaired, you’re done. Otherwise, you may need to do one of the following steps.
If Disk Utility reports “overlapped extent allocation” errors, two or more files occupy the same space on your disk, and at least one of them is likely to be corrupted. Check each file in the list of affected files. If you can replace a file or recreate it, delete it. If it contains information you need, open it and examine its data to make sure it hasn’t been corrupted. (Most of the files in the list have aliases in a DamagedFiles folder at the top level of your disk.)
If Disk Utility can’t repair your disk or it reports “The underlying task reported failure,” try to repair the disk or partition again. If that doesn’t work, back up as much of your data as possible, reformat the disk, reinstall Mac OS X, and then restore your backed-up data.If you continue to have problems with your disk, it may be physically damaged and need to be replaced.
Thank you for using Apple Support Communities.
Cheers,
Sterling

My Mac pro will not boot. it gets stuck on the grey screen.

My Mac pro will not boot. it gets stuck on the grey screen. What can I do?

Mac OS X: Gray screen appears during startup
If using 10.7 or later, the Installer/Utilities DVD has been replaced with a special emergency partition on the Hard drive called "Recovery_HD"

My phone will not let me restore it, I tried several times and when I install the frimware gets error and nothing is installed. What can I do?

My phone will not let me restore it, I tried several times and when I install the frimware gets error and nothing is installed. What can I do?

My phone will not let me restore it, I tried several times and when I install the frimware gets error and nothing is installed. What can I do?

Data Recovery off of a drive that will not boot

I have a server which will not boot into windows, I really just need to grab a few files off of it, I have downloaded several types of software and of course there is a limit on how much it will restore then it wants you to pay, the size is about 52 gb's, I used to use WINPE, does anyone have a piece of software that is free that I can recover this data since I can not boot into windows?
This topic first appeared in the Spiceworks Community

Did you do this:
Repair the Hard Drive
Boot from your Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. Select the external volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. Quit the installer to restart the computer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
See if this works to repair the drive.

Mac Pro will not boot from Leopard or any CD or DVD install disk

My Mac Pro wont boot from my Leopard install DVD. It never gets by the gray screen, then after several minutes the screen scrolls down black and says I need to restart my computer. I tried my Tiger install disk and it still wont boot from that DVD. Held down the "C", used "option" and selected DVD and still no boot. I can boot from one HD that has Leopard 10.5.8, but another HD with Snow Leopard 10.6.3 will not boot. The HD with Snow Leopard shows up as "EFI Boot" not the name I gave that HD when I startup using the "option" key. Any help would be appreciated.

At first I was just going to say it sounds like you have a bad optical drive, but then you had to go and say that it also won't boot from a HDD.
That just makes things a whole lot worse.
Start by removing the side cover and checking the RAM to see if any of the LEDs are lit up indicating bad RAM. Usually if there's any bad RAM found, it will just automatically disable that stick, but maybe yours isn't for some reason.
Look for any other LEDs that may be lit. Generally speaking, the only time you should see an LED (outside of the power LED) lit consistently is if there's a problem.
You should also see if you can get Apple Hardware Test to run, which may or may not find some problem.
But sorry to say, it's sounding very suspiciously like a bad logic board.
One other thing to try, is putting the SL drive into a different slot. So if you were putting it in slot 2, try slot 3 or 4. If you just have a bad SATA port, you might be able to just work around that until you get a new system.
If by chance this system is still under warranty, do not walk, do not pass go, do not collect $200, RUN to the nearest AASP or Apple store to make it THEIR problem to sort out.

After updating to Lion my macbook pro does not startup, it is stuck to the grey apple screen

After updating to Lion my macbook pro does not startup, it is stuck to the grey apple screen

See Here for Troubleshooting Grey Screen on Startup:
http://support.apple.com/kb/TS2570

Mac stuck on the grey apple screen startup? Follow these steps to re-boot....

So today I had a little scare with my Macbook. It was stuck on the grey apple startup screen with the loading icon. Switching it on and off did nothing and neither did waiting. I did a lot of browsing to try and find a solution but all the forums ended in 'looks like thats the end of my mac' or 'I think i've lost everything' or 're-install Os' blah blah etc. I DID NOT WANT TO LOSE ANYTHING!!! and I'm guessing neither do you! Ok so enough talking, in the end I found a solution which worked perfectly for me and I did not lose anything!!!!!:
Step 1
If the Mac is on switch it off.
Once it is off, switch it on again but this time as soon as you press the power button to switch it on, hold down the Apple cmd key + S.
Hold this down untill the 'safe boot' screen appears.
A black screen with white writing should now come up.
Step 2
Once the screen has loaded, at the bottom type:
/sbin/mount -uw /
[press enter]
then type:
chmod 775 /
[press enter]
then type:
exit
this re-boots the mac. As soon as you have done this the mac should load up again as normal!! Voila!!!
Hope it helps!

Someone suggested this to be risky. worked for me but DON'T DO IT WITHOUT RESEARCHING FIRST and if in doubt CALL APPLE!!!!!

Disk utility, software update, garage band, security, etc. will not open.

I tried to update my itunes about 2 weeks ago. it started downloading, maybe it did all the way, i dont know. because everything stopped working. i can use safari/firefox, office programs and some others but when i try opening disk utility, software update, security (and other programs) they will not open. they come up in the bar at the bottom of the screen for a second then vanish with no warning or error (and no program actually opens).
at first i just deleted itunes completely thinking that was it but now I cant even download that again, as I cant use disk utility to open in.
also, i cant backup my files, i have no way. if i run the reinstall disk will it delete all my files or is there a way to only modify files?
thanks in advance for any advise!

Hi, and a warm welcome to the forums!
Qyuick, do thus 1st...
"Try Disk Utility
1. Insert the Mac OS X Install disc that came with your computer, then restart the computer while holding the C key.
2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu. (In Mac OS X 10.4 or later, *you must select your language first.)*
*Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.*
3. Click the First Aid tab.
4. Click the disclosure triangle to the left of the hard drive icon to display the names of your hard disk volumes and partitions.
5. Select your Mac OS X volume.
6. Click Repair. Disk Utility checks and repairs the disk."
http://docs.info.apple.com/article.html?artnum=106214
Then boot off the HD and...
About Disk Utility's Repair Disk Permissions feature...
http://docs.info.apple.com/article.html?artnum=25751
Reboot needed if many Permissions are fixed, and possibly reapply latest Combo Update also.

Disk Utility wont drag drives on Mac book Pro

I am tring to back up may system drive, and i cant drag it to the source on disk utility, acctually i cant drag anything into it, while i have no problems on my dual g5, so i guess the problem is on the intel disk utility.
any ideas?

You need to drag the volume, not the "disk"
On most Macs, this would be "Macintosh HD"
Scott

Mac Mini will not boot up - Poss due to Mavericks?

I've had a MacMini since Nov 11 and it's never caused me any problems until lat night.
I updated to Mavericks on Fri afternoon and everything worked well until last night (Saturday).
On start up the screen had the Apple logo, a small revolving pattern thing and a progress bar.
The progress bar took about just under 5 minutes to finish and the screen went black and the Mac had no power.
I tried to reboot about a dozen times with the same result.
I have -
tried numerous key combinations to open safe mode (i only have a Windows keyboard)
disconnected all usb's except the keyboard and mouse
tried to reboot with keyboard and mouse disconnected
Nothing has worked
Does anybody have any ideas
Should I have left Mavericks alone?
I don't have any start up disk or external hard drive
Thanks
John

Sounds like you may need to Repair your Macintosh HD using Disk Utility.
To startup into Safe Mode startup holding the Shift key.
To startup into the Recovery Partition hold the Command R keys.
To start up into the Startup Manager hold the Alt (Option) key.
Be patient, key command startups are slower than normal startups.
If you can not startup into Safe Mode or the Recovery Partition, try the Alt (Option) to Startup Manager and startup from the Recovery Partition. Then go the Utilities > Disk Utility and in Disk Utility select your Macintosh HD > Repair.

2007 Mac Pro will not boot, even in safe mode

Hello,
I have a Mac Pro purchased in 2007 that had been working well up until a few months ago. I had trouble with Microsoft Word 2008 repeatedly crashing; I repaired the hard disk and moved up to Word 2011, and the problem seemed to resolve.
Yesterday, the machine crashed, and I am not able to start it up, even in safe mode. I have tried resetting the SMC and NVRAM/PRAM, removed and cleaned the graphics card (NVIDIA 7300 GT), and removed the 3rd party RAM I installed at least 2 years ago.
When booting to the internal hard drive, the Apple logo will show, then a blue screen followed by a gray screen with a frozen cursor. When I boot to an external hard drive or the OSX Leopard install DVD, the screen flickers like below:
When I tried to boot in safe mode while holding shift + command + V, the safe boot froze after reading:
panic (cpu 2 caller 0x2abf6a): kernal trap at 0x0029a4bc, type 14= page fault, registries:
[4 lines of 2-3 letter acronyms and numbers]
Error code: 0x00000000
I am thinking of buying a new graphics card (ATI Radeon 5700), but I want to be sure (as much as possible) that will solve the problem I am having. Any suggestions would be very much appreciated!
Thank you,
Cheryl

replace the system drive
always clone your system
yes dump the 7300 if you plan to keep using it and use Lion
A clean install would be nice start, on say 120GB SSD or something too
And 2x2GB FBDIMM set is $30 if you need a set
AHT is on your OEM DVD from 20007
dust, temps and air flow is also important

Mac Mini Will not boot from external drive or install disk

Hi,
I just bought a new 2.0 ghz mac mini 1 gb ram. 120gb hdd.
I have a separate external HDD attached and wanted to boot from this. It works with my MBP and IMAC.
When i plug it into the Mac Mini and start up with Option key. It recognizes it.
I then click on it. It automatically reboots.... then grey screen comes on. It goes black after about 10 seconds. then boots into original operating system.
I also tried to use the MAC install Disk, thinking it might be a corruption in the shipped software. It does the same thing.
I have MAC Install DVD on an external drive too. Same issue.
I partitioned the HDD and installed a copy of the Mac install disk onto that with disk utility... Same thing grey screen, then black then back to original operating system.
Not sure what is going on?
thanks
Chris

Hi,
Thanks.
It is running 10.5.8.
I am trying to boot up an external drive with 10.5.8 on it. It works on my Macbook Pro which is running 10.5.8, runs on my IMAC running SL. But doesnt work on the mac mini?
It had been running SL, however there are a number of programs I have like Windows Live Sync which are not yet compatable with SL so i downgraded to 10.5.6 which came with the Mac Mini then loaded all updates.
It seems to just go into an auto reboot as soon as i click on it.
i thought it might be the firmware? Is it possible to downgrade them and then re-install?
I have reset the PRAM.
Any help would be appreciated.
Thanks

I am in mavericks disk utility recovery mode as my mac book will not boot up & stays only on the grey apple screen. When I verify the disk I get open error5 :input /output error on Syst stuck on 1 minute pouring out over 50 error messages & still counting

Similar Messages

Maybe you are looking for