I tried to use Battery updater and it failed, now it starts up on my computer boot up evrytime and fails everytime, how do you turn it off or get it to work?
I tried to use the Battery updater software on my Powerbook G4 and it didn't work, now it starts up on my computer startup everytime, how do you get it to work or turn it off?
It's possible that your model PowerBook doesn't need the updater.
Did Software Update offer you the Updater, or did you download it from Apple? This article"
http://support.apple.com/kb/HT2339
has a list of the specific Mac models requiring the update and how to tell if you have one of those models--if yours is not among them, the updater shouldn't run.
Similar Messages
-
grandaughter has locked i pad 2 with passcode and then forgotten number how do you reset i pad to get it to work again
If You Are Locked Out Or Have Forgotten Your Passcode or Just Need to Restore Your Device
1. iTunes 10 for Mac- Update and restore software on iPod, iPhone, or iPad
2. iPhone, iPad, iPod touch: Wrong passcode results in red disabled screen
3. iOS- Understanding passcodes
If you have forgotten your Restrictions code, then follow the instructions
below but DO NOT restore any previous backup. If you do then you will
simply be restoring the old Restrictions code you have forgotten. This
same warning applies if you need to restore a clean system.
A Complete Guide to Restore or Recover Your iDevice (if You Forget Your Passcode)
If you need to restore your device or ff you cannot remember the passcode, then you will need to restore your device using the computer with which you last synced it. This allows you to reset your passcode and re-sync the data from the device (or restore from a backup). If you restore on a different computer that was never synced with the device, you will be able to unlock the device for use and remove the passcode, but your data will not be present. Refer to Updating and restoring iPhone, iPad and iPod touch software.
Try restoring the iOS device if backing up and erasing all content and settings doesn't resolve the issue. Using iTunes to restore iOS devices is part of standard isolation troubleshooting. Restoring your device will delete all data and content, including songs, videos, contacts, photos, and calendar information, and will restore all settings to their factory condition.
Before restoring your iOS device, Apple recommends that you either sync with iTunes to transfer any purchases you have made, or back up new data (data acquired after your last sync). If you have movie rentals on the device, see iTunes Store movie rental usage rights in the United States before restoring.
Follow these steps to restore your device:
1. Verify that you are using the latest version of iTunes before attempting to update.
2. Connect your device to your computer.
3. Select your iPhone, iPad, or iPod touch when it appears in iTunes under Devices.
4. Select the Summary tab.
5. Select the Restore option.
6. When prompted to back up your settings before restoring, select the Back Up
option (see in the image below). If you have just backed up the device, it is not
necessary to create another.
7. Select the Restore option when iTunes prompts you (as long as you've backed up,
you should not have to worry about restoring your iOS device).
8. When the restore process has completed, the device restarts and displays the Apple
logo while starting up:
After a restore, the iOS device displays the "Connect to iTunes" screen. For updating
to iOS 5 or later, follow the steps in the iOS Setup Assistant. For earlier versions of
iOS, keep your device connected until the "Connect to iTunes" screen goes away or
you see "iPhone is activated."
9. The final step is to restore your device from a previous backup. If you do not have a
backup to restore, then restore as New.
If you are restoring to fix a forgotten Restrictions Code or as a New device, then skip Step 9 and restore as New. -
In the URL bar, type about:config
Type geo.enabled
Double click on the geo.enabled preference
Location-Aware Browsing is now disabled
Google will not remove their location aware feature saying it is picked up by the location aware feature in my firefox browser and referred me to your like where I found the above to disable this feature. It just sent me to a yahoo search page. How do you disable this I want to use US Google not Google.ua and you don't need this to help me locate anything in the Ukraine. When I take my laptop with me on trips does my firefox local change wherever I go?See:
* http://www.mozilla.com/firefox/geolocation/
*http://browserspy.dk/geolocation.php -
What is the Debugger and how do you turn it off?
Hi folks, I'm updating a site for a client and when I open
the home page
http://www.imcnewcastle.com
I get this annoying pop up from Adobe flash player 10 asking
if my debugger
is on this machine or host application and it locks up if I
try to connect
to local.
What the heck is this and how do I keep it from turning on? I
don't want
browsers to get locked up.
Thanks
Jeff
~~~~~~~~~~~~
Jefferis Peterson, Pres.
Web Design and Marketing
http://www.PetersonSales.comJeff,
> I get this annoying pop up from Adobe flash player 10
asking
> if my debugger is on this machine or host application
and it
> locks up if I try to connect to local.
It's annoying when you don't want to bebug, I agree, but the
situation
you're describing is really useful when you need to debug
Flash content in a
browser. ;)
> What the heck is this and how do I keep it from turning
on?
> I don't want browsers to get locked up.
Assuming you have the FLA source file, open it in the Flash
authoring
tool and head over to File > Publish Settings. Select the
Flash tab, then
uncheck the "Permit debugging" checkbox, then republish the
SWF.
Here's more information on debugging:
AS2
http://www.adobe.com/devnet/flash/articles/debugging_actionscript.html
AS3
http://www.adobe.com/devnet/flash/articles/as3_debugger.html
David Stiller
Co-author, ActionScript 3.0 Quick Reference Guide
http://tinyurl.com/dpsAS3QuickReferenceGuide
"Luck is the residue of good design." -
This is little gray square with white button in center, It has multiple levels below home screen.
MikeThat's assistive touch. It's an accessibility feature.
-
What is this black bar on my screen and how do I turn it off?
There is a black bar on the screen that tells you where you are on the screen ....what is this called and how do you turn it off?
Can you provide a screen shot?
Ciao. -
Ive just upgraded to Mountain lion, I was using Safari and tried to use iCloud tabs. When I open it up there are no tabs there, anyone have any ideas on how to get it working?
Can you check system update? I think I did a system Update 1st, a day before installing OSX Lion and there is a Safari update. If not try logging in iCloud.
-
I just updated to ios 7 on my iPhone 4 how do you turn the apps off when your not using them? The old way of double clicking and then pressing the app until a red minus button comes doesn't work it opens it back up!?
Double click home button, then swipe up on app picture (not the icon itself)
-
Tried to check on updates for CS6 64 bit - Received message saying application manager may be damaged - download and install new copy - when I try this I receive message ERROR 404 I have a PC - any help would be gratefully received - thanks - William
reset your preferences:
dreamweaver: http://helpx.adobe.com/dreamweaver/kb/restore-preferences-dreamweaver-cs4-cs5.html
flash: http://helpx.adobe.com/flash/kb/re-create-preferences-flash-professional.html
indesign: https://forums.adobe.com/thread/526990
lightroom: http://www.lightroomforums.net/showthread.php?14226-Resetting-%28or-Trashing-%29-the-Light room-Preferences-file
photoshop: https://forums.adobe.com/thread/375776
if that fails, uninstall ps, clean (Use the CC Cleaner Tool to solve installation problems | CC, CS3-CS6) and reinstall. then use the manual updates. -
Tried to download itunes update 11.1.4. At 99% IE said, "This program contained a virus and was deleted." Anyone else with this problem? What do I do?
Hi JEOQ,
Thanks for visiting Apple Support Communities.
You may find the information and steps in this article helpful with downloading iTunes:
iTunes: Downloading iTunes for Windows using Internet Explorer
http://support.apple.com/kb/ts3212
Best Regards,
Jeremy -
I have two apple id's because my hotmail account is no longer active. How can I delete the old one and use or update the new one? Every time I try it won't allow me and now my iPad thinks there are two accounts and they are arguing with each other. Help!
You can't merge accounts or copy content to a different account, so anything that you bought or downloaded via the old account is tied to that account - so any updates that those apps get you will only be able to download via that account. You can change which account is logged in on the iPad via Settings > Store
-
Before I upgraded my iPad mini, you could turn off apps to save battery power by double clicking the control button and then holding your finger on the app button until the minus sign appeared. That doesn't work anymore. How do you turn off the apps with ios7
Now you swipe downward, the app will appear and you delete, keep scolling to the right as in the past. With the new operating system you also swipe downward to get the search bar to find an app
-
I have a mid 2011 27 inch iMac and a late 2012 mac mini. I am using the 27 inch iMac as the display for the mac mini with a thunderbolt cable. I was trying to use bootcamp on the mini but after I started downloading windows I can't get it to display on the iMac.
Hi there,
The simplest way is to drag it across wirelessly using the 'Airdrop' application once both computers are near one another. 'Airdrop' can be found near the top, on the left hand side menu, within 'Finder'.
AJ -
I am trying to use automator to open a safari popup window that will automatically log me into whatever account and I attempted to type up an applescript that utilized the "System Events" function with no avail, any ideas?
Hi
In iMovie'11 (version 9.0.x)
on top menu row - Apple/iMovie/File/Edit/Cut (Can vary dep. on language - in Swedish Apple/iMovie/Arkiv/Redigera/Klipp . . . )
down Cut menu - Slow playback/Raspid Playback/Re-play in Slow Motion and onvards
Here one can select the Pre-Set speeds
Are you familiar with getting 'inspector' to run?
No - but I guess that Double Click on clip/sequense or ctrl-Click on it might open it.
Yours Bengt W -
Since updating to iOS6, im on giff gaff and I don't know how to set up the VPN to get 3G to work?
oh sorry, well since i have updated to iOS6 i turn on my 3G, then try to connect to the internet with 3G and it says ''Could not activate mobile data network'' then underneath that says ''You are not subscribed to a mobile data service'' would you be able to help?
Maybe you are looking for
-
I have a pioneer vsx-910-k and airport express.I have a wireless network at home. What's the best arquiecture/config to do with this hardware?
-
Problem with Quicktime...need help...
I used to visit "VirusRadio.com" frequently and listen to old Opie and Anthony shows online, and never had a problem. Here lately (after installing XP Pro, I've noticed) I've been totally unable to stream content off this website. When I had Home Edi
-
How to determine the Class of a static methods class?
hi, is there a way to get the code below to output foo() called on One.class foo() called on Two.classthanks, asjf public class Two extends One { public static void main(String [] arg) { One.foo(); // should say "foo() called on One.class"
-
Attaching a note from PA30 transaction in the workflow
Hi All, I have developed a workflow which gets triggered when a record for infotype 0267 is created in pa30. Initially when the record got created a work item appeared in the approvers inbox and he could either approve or reject it. Now the requireme
-
I am trying to activate my phone. I got all the way through the payment and everything twice but it won't activate and now I've put twice as much as I wanted on. My signal is good. What do I do?