IBM Hard Drive Only Runs In One Computer

Hey guys,
I have a weird little problem with an IBM Travelstar hard drive. I am working on a Dell Latitude 400 for a friend. She wanted XP installed on her laptop, as it currently has some version of Fedora on it, and she dislikes Linux. However, her computer does not have a disc drive, floppy drive, or support for USB boot. So, I went on to Ebay, and bought a 2.5 to 3.5 IDE hard drive adapter, and went through the process of installing MS-DOS 7.1 to a spare drive, and using that to install XP. Sure enough, using my spare drive, everything worked smoothly. However, when I tried the same thing with her hard drive, none of my computers can find it. My Gateway 2000 cannot detect it, my A31 Thinkpad cannot detect it, and so on and so forth. Of course, when her hard drive is in her Dell, it runs fine.
I am wondering if maybe the hard drive is somehow 'locked in' to her computer...as I have experienced a similar problem with another hard drive that would only run in an I 1200 Thinkpad. The model number off the drive in question is IC25N010ATDA04-0. It has a manufacturing date of April 02. If anybody has any ideas, I would really like to hear them.
Thanks in advance,
- Nycto

Right, Windows cannot handle ext3. I am aware of this. I tried reformating the disc with one of my Kubuntu discs, and Kubuntu could not detect the hard drive. I couldn't detect the drive with Max Blast either. I have yet to try every computer in my house, but, thus far, regardless of operating system, the only computer that will can detect the drive is the Dell from which I pulled it. When I boot my Gateway 2000 with the laptop drive attached, the bios only recognizes the two CD-ROM drives and my primary hard drive. Even when the laptop drive is the only drive in the system, it fails to detect the drive. So I couldn't tell you if I could view the drive in Windows' Device Manager, as I can't even get Windows to boot with this drive connected. And, like I said, Kubuntu couldn't find the drive either.
I know my converters work, as I was able to successfully install Windows using the previously described method with an old Hitachi notebook drive I had lying around. Additionally, as I mentioned before, I have seen this once before with another IBM Travelstar...except that drive was only detected by an IBM Thinkpad 1200. Which is why I wondered if there was something built into the hard drive's firmware that locked it in to a particular computer or something. I've tried most of the obvious stuff...jumper settings, loose cables, etc, and yet I don't have any other computers that can detect the drive.
I'm tempted to solve my Windows XP installation by installing VMWare, or something similar, to the Dell, and then copying over an ISO of XP, and mounting it in a virtual drive and installing it that way...but this machine is so old, I doubt it's a good idea to run XP on top of Linux...

Similar Messages

Moving a hard drives with songs from one computer to another

I'm going to have my collection of music on one external hard drive, but I'm streaming from one computer using ATV to my home stereo system, but managing the music on the external drive (adding mostly) from another machine. (The reason is that the streaming machine is much older and slower - works for streaming but my USB ports are crappy and so I want to be able to add music directly to the hard drive from my newer, faster notebook).
Given this scenario, if I add music to the external drive from the newer notebook, when I go to connect it to the streaming machine, what do I have to do each time to update Itunes on that computer?

you could try copying and pasting the songs on to a usb.
plug the usb into the desk top and paste them onto itunes.
idk if it will work but its worth a try. i managed to get songs from my psp to my ipod this way

Hi. My iMac hard drive is running Mavericks. I have an old version of Quark Xpress (3.32) which won't run in Mavericks. Can I partition my hard drive and run an older system on one partition, so I can access my Quark? Is that possible?

Hi. My iMac hard drive is running Mavericks. I have an old version of Quark Xpress (3.32) which won't run in Mavericks. Can I partition my hard drive and run an older system on one partition, so I can access my Quark? Is that possible?

Hi ancelau,
QuarkXPress 3 is a Classic Mac OS application, so you need a version of OS X that still supports Classic. I believe 10.4 was the last one.
So if you have an iMac that boots with 10.4, then yes that is possible. I doubt though that newer Macs boot with OS X 10.4.
So why don't you upgrade QuarkXPress 3 to a newer version? I am not just asking that because I want you to spend money with us.
Typically using software that was released almost 20 years ago is just feasible when you keep an environment that was current at the time of release or a few years after, so an older Mac with a operating system present at that time. 20 years in IT is a lot.
So my opinion is that on a new Mac with a brand new operating system you need to use something a bit more current.
How about QuarkXPress 9 (released 3 years ago) or QuarkXPress 10? You are better off with v9, as QuarkXPress 10 only opens v7 and higher (whereas QuarkXPress 9 opens v3.1 and higher).
Or - I am even happy to make an exception - upgrade to 9 and we give you 10 for free? Let me know please.
Thanks
Matthias

Can i partition hard drive and run 10.6 on one and 10.4 on other

I have software that only runs under 10.4 on my older Imac. I would like to partition hard drive and run 10.6 on one and 10.4 on the other. Is this possible? Can I get instructions?

Yes.
Just set up the partitions. If you already have a 10.4.x and 10.6.x drives then "clone" them up as bootable backups with a backup utility like Carbon Copy Cloner or Super Duper.
When booting you can hold down the option key to get a list of bootable volumes (select with arrow keys and hit return). You can use Startup Disk for either of them to define the default system to boot from if you don't use the option key technique.
If you don't already have these systems then of course you will have to install them in their respective partitions.
You have to realize of course that these are two distinct systems each with their own version of your login directory.

My HP computer's hard drive crashed. I have replaced the hard drive and reinstalled all of the software. I have copied my I tunes library from my backup hard drive to the new one. How do I restore the permissions? This is the 3 rd time I have had to d

My HP computer's hard drive crashed. I have replaced the hard drive and reinstalled all of the software. I have copied my I tunes library from my backup hard drive to the new one. How do I restore the permissions? This is the 3 rd time I have had to do this. THe share screen says you are limited to 5 ??

No backup is not good.
You can transfer itunes purchases from an ipod. File>Transfer Purchases

My hard drive crashed on my apple computer recently. I have a new one, but it won't sync with apple tv1, and I want to retrieve my photos from teh appletv1. It appears in devices now, but won't let me go any further with it. Help

The hard drive crashed on my apple computer and I lost a lot of photos. I want to recover them from my apple tv1, but the computer won't seem to pair up with the apple tv. The Apple tv does appear in devices, but it won't let me go any further. The 'apply' button is a pale grey colour and you can't click on it. Help!!

there is no facility to recover your photos from the appletv.
the only way to link the appletv to your new "system" is to remove the existing itunes link and then link it to the new itunes - this will delete all content from the appletv though.

I have upgraded to a new computer. I have installed iTunes from the internet and copied my music from the old hard drive to my new one. What do I need to do to get my new computer to recognize my old playlist?

I have upgraded to a new computer. I have installed iTunes from the internet and copied my music from the old hard drive to my new one. What do I need to do to get my new computer to recognize my old playlist?

See https://support.mozilla.com/en-US/kb/Backing%20up%20and%20restoring%20bookmarks
and
https://support.mozilla.com/en-US/kb/Backing%20up%20your%20information?s=new+computer&r=4&as=s#os=win&browser=fx8

I have a macbook pro 10.6.8 system. My hard drive was replaced under warranty. Since then, my computer runs hot. The original hard drive never ran hot. What would cause the new hard drive to run hot?

I have a 2011 MacBook Pro, OS X 10.6.8, 2.2 GHz Intel Core i7, 4 GB 1333 MHz DDR3. This is my first computer so don't know anything about trouble shooting. A week before the warranty expired, I took my computer to Apple to be checked. I was told that my hard drive was bad and they replaced the hard drive. Since then, my computer runs hot most of the time and the fan is constantly coming on, which is good My computer rarely ran hot with the original hard drive. What would be causing this?

racergirl,
have you tried resetting your MacBook Pro’s System Management Controller, to see if that makes a difference with the heat?

Two hard drives, two operating systems, one MacBook Pro

Dear community,
     I have a MacBook Pro (mid-2010) with Mac OS Lion. I plan on having this computer all through the rest of college (another two and a half years, hopefully) so I want to upgrade it just a bit. What I would like to do is take out my optical drive, install a second hard drive mount, and put an SSD in that spot. Now, this would be pretty simple if it were just Mac OS Lion that I wanted on it, but here's the catch - I'd like to put my copy of Windows 7 on that drive as well. I currently use one hard drive for Mac/Windows 7 using boot camp, so I figured it'd be possible to do this with 2 hard drives.
     Basically I'd like to put the OSes and a few programs on the SSD, and the files/remaining programs on my big HDD. Is this even possible? Any suggestions?
     In summary: Mac OS Lion and Windows 7 + a few Mac/Windows apps on the SSD; Mac OS and Windows data files and programs on the HDD. Can it be done?
Thanks a lot.
-Grant
*Note- here is the hard drive caddy I'm looking at: http://www.amazon.com/Drive-Unibody-MacBook-SuperDrive-Replacement/dp/B0058AH2US /ref=wl_it_dp_o_npd?ie=UTF8&coliid=I1MJCRJMNCU4QQ&colid=1LV4HAU48M27X

grantmcconnaughey wrote:
Dear community,
     I have a MacBook Pro (mid-2010) with Mac OS Lion. I plan on having this computer all through the rest of college (another two and a half years, hopefully) so I want to upgrade it just a bit. What I would like to do is take out my optical drive, install a second hard drive mount, and put an SSD in that spot. Now, this would be pretty simple if it were just Mac OS Lion that I wanted on it, but here's the catch - I'd like to put my copy of Windows 7 on that drive as well. I currently use one hard drive for Mac/Windows 7 using boot camp, so I figured it'd be possible to do this with 2 hard drives.
     Basically I'd like to put the OSes and a few programs on the SSD, and the files/remaining programs on my big HDD. Is this even possible? Any suggestions?
The SSD should be the boot drive in the present hard drive spot for these reasons.
1: You want the SSD as the boot volume for speed of OS X, Windows and applications (must be on boot drive along with one bare bones user, each OS)
2: You want to inflict as little change to the SSD as possible to make it last longer as they can wear out with a lot of use, thus a boot/app drive is ideal for this.
3: Present hard drive becomes the exFAT formatted drive to use for Windows or Mac file storage use in the optical bay caddy.
Problems:
You can't install Windows from a external optical drive, only the internal one.
You also won't be able to boot off a 10.6 install disk just the same.
However you can option boot off 10.6/10.7 previously installed, or cloned (Carbon Copy Cloner), on a external drive.
Windows in Bootcamp is subject to the same problems requiring reinstall like it is on PC's, which to reinstall would require you to install your internal optical drive each time.
You can't make a bootable clone of Windows on a external drive and use it (because of validation issues with the drive Windows is installed on) or use it to restore Bootcamp (there used to be software that did this for Snow Leopard, but it hasn't been updated anymore)
Also if your 2010 MBP doesn't have SATA 6, your going to be using SATA 3 and not the full speed capability of the SSD.
What you might consider doing instead is getting a 1TB 7,200 RPM boot drive, you get storage size to partition and decent speed, without excessive speed which you might not be able to use it all with your hardware.
Another option, if your using Windows for non-hardware presisng issues (3D games, heavy CPU loads) is to use virtual machine software (VMFusion, Parrallels Desktop etc) and run Windows in a window on OS X. This gives the advantage of Windows running as a file, and you can have earlier "snapshots" in case Windows gets hosed like it does sometimes.
Also Bootcamp restricts you to Windows 7, with virtual machine software you can run any Windows version, even cool Linux distros too (install older versions first then upgrade) Plus you don't have to dual boot or worry about file formatting issues, which both is a pain in the butt.
Lion is a pain to reinstall on a new hard drive directly with older hardware (two steps involved), luckily you've got a older machine and can install 10.6.8 first, then upgrade by holding option key and clicking on Purchases, then apps, then files, then bootcamp or virtual machine software, then Windows.
Should make a copy of that 10.6 disk
http://www.walterjessen.com/make-a-bootable-backup-snow-leopard-install-disc/
So anyway, that's a loadful to think about.
What you should do is join the MacOwnersSupportGroup and ask Bmer how best to go about installing the optical drive kit. I've send all these sort of hardware hacks his way as he has done it himself so he knows.
Apple obviously doesn't support such a thing and nearly none here can offer any support in such a thing.
OtherWorld Computing has a kit as well, gives a enclosure for the Superdrive to use as a external optical drive as well. (just can't boot or install Windows with it.)
As always this is all I know and subjective to change, so ask around further and perhaps you'll find more answers, but likely not here.
See this for fast SSD choices
http://www.harddrivebenchmark.net/high_end_drives.html
Good Luck and hope that helps.

I currently have a MAC Mini, which has 1 Firewire 800 port. I have a 1TB external hard disk that runs at Firewire 400. Can I insert another external hard drive that runs at Firewire 800?

Here's the deal. Currently running SL 10.6.8 on a MAC Mini. Planning for eventual upgrade to ML. Have a 1TB external hard drive partitioned into two volumes, one volume for Time Machine and one volume for SL which I periodically update using Superduper. Thus I always have a point-in-time bootable backup on the external hard drive.
The MAC Mini supports Firewire 800. However, booting from my current external hard disk is pretty slow, since it only supports Firewire 400. I am considering buying an Iomega MiniMax which supports Firewire 800. Then, I would use the MiniMax as my bootable backup volume, and relegate the older hard drive to Time Machine.
So, question #1 is, can I daisychain the new MiniMax between the MAC Mini and my existing external hard drive? My expectation is that the new Mini Max would run using Firewire 800 and that the existing hard drive would run at Firewire 400 speed as it does today. If it doesn't (e.g., daisychaining in the Firewire 400 external disk with the MiniMax Firewire 800 external disk ends up running the whole leg at 400), my resolution will be to run the existing hard disk off an available USB port and have just the MiniMax running at Firewire 800.
Why am I going to all this trouble? That's question #2. I don't trust upgrades; they always break something. When I upgraded from 10.5.x to 10.6.x, the web directories got renamed, and all of my web apps 403'd until I figured out what happened. Plus, I have accounts for other family members, and in order to ensure their ability to use the computer during my upgrade process, I need to have the ability to fall-back quickly to a known-stable version of OSX. So what I'm trying to do is insulate myself from problems by partitioning the MiniMax into two volumes, taking a Superduper image of my current installation on the Mac Mini to MiniMax external drive volume 1, then upgrading to ML on the MAC Mini, and take a SuperDuper image of that to MiniMax external drive volume 2. Then, if the upgrade results in problems I can't resolve immediately, I can simply reimage the MAC Mini from MiniMax volume 1. BUT ...
... I've read that the ML installation creates a "service and support" partition that is different than the startup disk. I'm concerned that I won't be able to reimage the hard disk in the MAC Mini once I upgrade it to ML because of the partitioning changes it introduces on the startup disk. Theoretically, I +should+ be able to use the disk utility on my SL system to repartition the disk in the MAC Mini prior to reimaging it from my backup, but I'm considering the possibility that the new partition may be of a type that the SL disk utility cannot identify, and might therefore be unable to delete or even detect. So I'm hoping someone else has been down this road and can advise me. Even at Firewire 800 speeds, booting from an external disk is still going to be slow, so I want to be able to restore my SL image to the MAC Mini hard disk.
A little background on me. I work for a major disaster recovery provider. I used to have a Mac PRO G5, which I got used, and the first thing I did with it was install a second hard disk, SuperDupe an image from the first disk to the second, and made sure I could boot from the second. THEN I started using and customizing the MAC. I really feel vulnerable with the MAC Mini, since it only has the single internal hard drive - sort of like going out in public dressed only in a long T-shirt. So my whole thing is, I ABSOLUTELY MUST BE ABLE TO PUT THINGS BACK THE WAY THEY WERE before I do the migration to ML.
Obsessive-cumpulsive? Yep. Anal? You got it. That's why I'm in the DR business.

You may have overloaded the port, following the instructions below it should reset:
+1. Shut down the computer.+
+2. Disconnect all devices and all other cables, except the keyboard and mouse cable(s).+
+3. Disconnect the computer from the power outlet and wait for 3 to 5 minutes.+
+4. Plug the computer back in and turn it on.+
+5. Reconnect the device(s) (one at a time if there is more than one) and test. Test with each port if you have more than one.+
http://support.apple.com/kb/HT1317?viewlocale=en_US

Can not get external hard drives to connect to my computer 17" Mac book Pro 10.7.5

can not get external hard drives to connect to my computer I am using a 17" Mac book Pro 10.7.5.
I have 2 iomegas and 1 LaCie. Changed cables. I can feel the external hard drives running and
I can hear them running but I can not get them on the computer any more. They did work at one time.
Can any one PLEASE help?

Nothing appear on my desktop.
I did Repair and Verify the HDDs in Disk Utility>First Aid from the
Utilites App about a dozen times ans they all said everything was good
except for the last time there were erors found and I ran the
Disk Utility from the Start Up Disk and the repairs were made and everything
was subposed to te good and still Nothing on the desk top.
Ginger

PSE 9, external hard drives and moving to new computer

I had an old desktop running PSE 3, yep...3, and my husband bought me a new laptop. Laptop's operating system would not run PSE 3, so I purchased PSE 9, reconnected all my "misplaced" photo files, loaded PSE 9 on the old desktop and converted all files to 9. NOW, I am ready to move everything to the laptop and am unsure what would be best.
I have a large collection of photos and have always stored them on an external harddrive that I just plug in when needed. I purchased a second external hard drive that I am now using for backup ONLY, so I have 2 external HD's - (1) storage and (2) backup.
New laptop has PSE 9 installed and has a some newer photos in the organizer that are presently stored on the laptop harddrive. I have not done any tagging on the laptop because I didn't want to complicate matters. I now want to import my old catalog photos (stored on the external hard drive), including PSE tags. The part that causes me confusion is that I want to continue storing the photos on the external hard drive where they are. It seems counter productive to import, make new files on the laptop, then export back to where they were all along.
Gosh, I hope I'm making sense here. Anyone have any suggestions - simplest of terms, please, regarding how to get access to my photos and tags moved to the laptop if the fewest and easiest steps?

Ken, I am struggling with this. I have renamed the external harddrive with my photos, found the catalog and copied it to the external with the photos and have connected this external hard drive to the laptop (new computer).
I am now at step 5. of your first response. I have browsed and found the catalog, now my only two options are new or convert. I don't think I need to convert because I have already converted to from 3 to PSE 9 and don't really think it's a "new" catalog.
I need an "outline for dummies", please. If I didn't have so darn many photos, I'd be tempted to just start over. If it helps, I have written tag info to my files.
Thank you for all your patience and help.

HT4889 Replacing System hard drive with a new one. How to get everything over to the new boot drive?

Replacing System hard drive with a new one. How to get everything over to the new boot drive? Should I use Carbon Copy or does apple have a better untility to do this?
I can't get my current system drive (OSX 10.8.3) to start on the first try. I always have to shut down and restart again to finally see the Apple logo.
Have used disc utility to repair the disc and permissions several times and that works. The next time I boot up, it works fine and I get the apple logo, but then the second time I boot up, it's back to the blank screen again and it only boots after the second try. I have tried this repair three different times now always with the same result. Works right the first try (after the repair) then from the second time on it doesn't work. I just get the white screen until I reboot a second time.
Thinking I should change drives but what's the easist and best way to move everything over to the new drive so it will boot correctly with all my data on it. This is the system drive for a Pro Tools 10HD setup. MacPro 3,1 with 16 gigs ram and OSX10.8.3 on it.
Thanks for any help!

If you have a time machine back up of your current drive you can do this
Shut down your computer, install the new drive. While the computer is off plug in the external hard drive that you have your time machine back up on. Hold Option key while the computer turnes on, let go of the option key once you get a grey screen. Shortly after you'll see a list of bootable drives, select the one that has your time machine back up on it and boot into that drive.
From there go into disk utility, format your new drive too, osx extended journaled ( I think, double check that, its been awhile since ive had to do this), hit format
Exit disk utility and then you can use time machine to copy all your exisit data to the new hhd and then your pretty much done.
There is also a program called Carbon Cloner that will do esentially the same thing however I've never uesed it.

Restore new hard drive from an older one

so i only have 120gb on my current hard drive. im planning on getting a 500gb hard drive to put into my mac, and buy a case for the 120gb hd so i can use it as an external hard drive. the problem is, i dont have an existing external hard drive, so the 120gb one is all i have. i want to keep all my music and photos and all that stuff, so im wondering if i can just replace the internal hard drive with the 500gb one, then connect the 120gb one via usb and restore away.
also: when i install the new hard drive, will i need to use the leopard installation dvd to install, and then transfer my files from my external hd?or will i just be able to transfer everything from the external hard drive right away? and since the external hd should be bootable, when i choose to transfer files from the external(using migration assistant or whatever) should i click use *transfer from existing mac* or *transfer from an external volume* or smth?
thx in advance for the help
Kenneth

i want to keep all my music and photos and all that stuff, so im wondering if i can just replace the internal hard drive with the 500gb one, then connect the 120gb one via usb and restore away.
Yes. Put it into an enclosure such as the case you mentioned and connect it to the computer.
when i install the new hard drive, will i need to use the leopard installation dvd to install, and then transfer my files from my external hd?
Use the installation DVD, or place the 500GB drive in an enclosure, use a tool such as SuperDuper or Carbon Copy Cloner to clone your current system to it, put the drive into the computer, and start using it immediately. No migration is needed in the second case.
when i choose to transfer files from the external(using migration assistant or whatever) should i click use transfer from existing mac or transfer from an external volume or smth?
If that step is needed, transfer the data from an external volume.
(44542)

I am running Snow Leopard on my iMac and have partitioned my hard drive to run Windows XP. If I upgrade to Yosemite, will I still be able to run XP?

I am running Snow Leopard on my iMac and have partitioned my hard drive to run Windows XP. If I upgrade to Yosemite, will I still be able to run XP?

bobfromnorth battleford wrote:
...Now what happens if I upgrade to Yosemite on either my iMac or my MBPro?
If I install VM Fusion or Parallels, does Windows run all the time? How does that affect computer performance? and how much do I need to worry about hard drive corruption?
Current versions of Fusion and Parallels are compatible with Yosemite. Both are applications which you only run when you want to run Windows within them. As such, there's no effect on computer performance when they're not in use. Like any other software, there is some additional load on your Mac when both Windows and the Mac OS are running together, but any noticeable effect depends on what each is being expected to do and what resources (e.g. available RAM and the number of CPU cores) you can devote to each.
I think there's less chance of HD corruption with a VM than there is with running Windows natively on the Mac in Boot Camp. Consider that, with a VM, you can create Snapshots of the state of your VM at a given time, and then, if something goes wrong (virus, malware, software installations), you can simply restore the Snapshot in a matter of seconds and eliminate the problems in the process. Moreover you can make a backup copy of the entire VM file, and replace a later version if you wish. Also consider that you can assign, say, 100GB of HD space to the VM, but the actual space devoted to the VM is only what's actually used; as more is needed, more is made available and Windows can't tell the difference. So, for example, my Win 7 Pro VM has an 80 GB virtual HD but only takes up 45 GB on my SSD, and that's with XP Mode in VPC installed inside it.
Microsoft no longer supports XP, though virus signature updates are still being issued. But MS has installed a pop-up message about EOL that won't go away (it's installed with KB2934207). Even if you remove that KB in Add and Remove Software, the pop-up continues. But if you have a Snapshot or a backup which is prior to it's original installation, you can skip installing KB2934207, and suppress it's reappearance on a Software Update list.

IBM Hard Drive Only Runs In One Computer

Similar Messages

Maybe you are looking for