Ibrdf with eabo timeout
hi
i am getting eabo timeout error after i use ibrdf
in particular i am writing a jpeg file (from instrument screen capture)
a file is written (over 100k) but i guess it is corrupt because it cannot be opened (actually one program irfan view in windows can open it, it must be doing something special), i suspect the file is not closed properly with the timeout error? ibrdf is supposed to close the file.. im confused
i played around with timeout settings but without any luck
any help appreciated, thx
Hi Daniel Kh,
Set the EOS character by looking at this KnowledgeBase
http://digital.ni.com/public.nsf/websearch/3AA75CCAC94E18BB862564F00079D2AD?OpenDocument
The EOS character for your device is a line feed character 'lf'.
Though your device seems to send out both LF and EOI. I'm not sure why the EOI is not terminating the read. (perhaps a bad cable?) Either way, see if the setting of the EOS works. As for the ibdev configuration, take a look at:
http://linux-gpib.sourceforge.net/doc_html/r1297.html
Tells you what the parameters should be.
I found the termination by looking at the programming manual for your device under the section named "Terminating".
Hope this helps!
Chris T.
Applications Engineer
National Instruments
Similar Messages
-
What's up with Session timeout. That is all I can get anymore?
What's up with Session timeout? That is all I get anymore with I Tunes Store.
The fix was: Turn off Junk Mail filter
quit mail
turn on junk mail filter
(and reset database for good measure) -
How to deal with session timeouts?
How to deal with session timeouts?
With our current configuration of using single signon, when the web session times out (currently 20 minutes of inactivity), the user loses anything they have entered on a service form. The use case is that a user starts filling out a form and gets interrupted, goes to lunch, etc, returns and spends time filling out the form (in the mean time the web session has timed out). When they try to submit the service they get re-logged in through SSO and they have lost all of their entries in the service. This creates some very unhappy users.
I'd like to know how long other customers set their web session timeouts to and if anyone has come up with ways of handling this situation - either through somehow re-establishing the session or through warnings to the user about how long they have to complete a form.Hi,
The timeout period for HTTP sessions that are created in the corresponding Web application. After being inactive for the specified timeout, the HTTP sessions expire. The period is specified in minutes:
<!ELEMENT session-timeout (#PCDATA)>
You can only change the session timeout property in the applicationu2019s own deployment descriptors. This is not possible for the Global Web Descriptor.
following may help you:
[Additional Configuration Settings |http://help.sap.com/saphelp_erp2005vp/helpdata/en/a9/7a9602ad094b82a293f06d1cbe2c14/frameset.htm]
Regards,
Sahidur -
Wlan ssl upload failure with connection timeouts
I have WLAN-upload problems with my MacBook running OS X 10.9.4 on my ftp server.
The server is configured in passive mode and the ports are activated within iptables and SSL mode (explicit tls).
From my it is not possible to upload files without problems. On my colleagues older mac it is not possible whether using wlan or lan connection (not the same network!)
I am able to upload 1-5 files and then the client will loose the connection with an timeout, reconnects and tries to upload the same file again (means it's already on the server).
On the other hand I am able to upload out of the following virtual machines running on my mac using parallels: Ubuntu, Debian, OS X Yosemite DP7!
Furthermore I am able to upload files using my windows laptop (same WLAN) and my windows desktop computer. So I assume it is not the routers fault.
In my opinion and after reading about 20 guides from different websites, the ftp is correctly configured and there is no "NO MAC"-Option.
What I have tried already without results:
- Restored my MacBook to a clean OS X 10.9.4
- Compared the MTU of the clean install with my old install
- Compared the MTU with the virtual machines
- Tried FileZilla, Yummy FTP and Cyberduck
- Opened the ports in my router (though not neccessary)
What I have tried with results:
- Upload using a clean OS X Yosemite Parallels VM (on my MacBook!)
- Upload using a Ubuntu/Debian Parallels VM (on my MacBook!)
- Upload using a Windows notebook and Windows desktop computer
- Upload using a iPhone Hotspot on my MacBook (weird it was working)
Do you have any ideas what the problem could be? I don't think it is only my routers fault because it is possible to reproduce the problem on another macbook on another network. Additionally I am able to upload using virtual machines on my Macbook (super weird).
Is there a problem with the network adapter? Why is it working out of VMs but not the operation system itself?
best regards
SeferI have WLAN-upload problems with my MacBook running OS X 10.9.4 on my ftp server.
The server is configured in passive mode and the ports are activated within iptables and SSL mode (explicit tls).
From my it is not possible to upload files without problems. On my colleagues older mac it is not possible whether using wlan or lan connection (not the same network!)
I am able to upload 1-5 files and then the client will loose the connection with an timeout, reconnects and tries to upload the same file again (means it's already on the server).
On the other hand I am able to upload out of the following virtual machines running on my mac using parallels: Ubuntu, Debian, OS X Yosemite DP7!
Furthermore I am able to upload files using my windows laptop (same WLAN) and my windows desktop computer. So I assume it is not the routers fault.
In my opinion and after reading about 20 guides from different websites, the ftp is correctly configured and there is no "NO MAC"-Option.
What I have tried already without results:
- Restored my MacBook to a clean OS X 10.9.4
- Compared the MTU of the clean install with my old install
- Compared the MTU with the virtual machines
- Tried FileZilla, Yummy FTP and Cyberduck
- Opened the ports in my router (though not neccessary)
What I have tried with results:
- Upload using a clean OS X Yosemite Parallels VM (on my MacBook!)
- Upload using a Ubuntu/Debian Parallels VM (on my MacBook!)
- Upload using a Windows notebook and Windows desktop computer
- Upload using a iPhone Hotspot on my MacBook (weird it was working)
Do you have any ideas what the problem could be? I don't think it is only my routers fault because it is possible to reproduce the problem on another macbook on another network. Additionally I am able to upload using virtual machines on my Macbook (super weird).
Is there a problem with the network adapter? Why is it working out of VMs but not the operation system itself?
best regards
Sefer -
Hello Archers,
I've set up an svn Server with Apache folloing your wiki on my raspberry pi.
https://wiki.archlinux.org/index.php/LAMP
https://wiki.archlinux.org/index.php/Subversion_Setup
Unfortunately I get errors when I try to commit several files (15 or so). I think it is a timeout issue, however I don't know where to specify the timeout in the httpd.conf (or httpd-ssl.conf)
This is a client error message:
Commit failed (details follow):
Unexpected end of svndiff Input
And this the corresponding server side log:
[date] [dav:error] [pid 448:tid 2854220848] (70007)The timeout specified has expired: [client 192.168.178.55:63819] Timeout reading the body (URI: /Dokumente/!svn/txr/9-q/Music/myfile.mp3) [408, #0]
[date] [dav:error] [pid 448:tid 2854220848] [client 192.168.178.55:63819] mod_dav_svn close_stream: error closing write stream [500, #185004]
[date] [dav:error] [pid 448:tid 2854220848] [client 192.168.178.55:63819] Unexpected end of svndiff input [500, #185004]
I assume it is some error like this: http://subversion.apache.org/faq.html#s … -truncated
I think I don't have specified the timeouts correctly, since I haven't found the default option.
tl:dr
Do you know how to set the timeouts in the apache configuration file?
I very much appreciate your help.
arch on pi
Here are my configuration Files with my position for the timeout order:
httpd-ssl.conf:
# This is the Apache server configuration file providing SSL support.
# It contains the configuration directives to instruct the server how to
# serve pages over an https connection. For detailed information about these
# directives see <URL:http://httpd.apache.org/docs/2.4/mod/mod_ssl.html>
# Do NOT simply read the instructions in here without understanding
# what they do. They're here only as hints or reminders. If you are unsure
# consult the online docs. You have been warned.
# Required modules: mod_log_config, mod_setenvif, mod_ssl,
# socache_shmcb_module (for default value of SSLSessionCache)
# Pseudo Random Number Generator (PRNG):
# Configure one or more sources to seed the PRNG of the SSL library.
# The seed data should be of good random quality.
# WARNING! On some platforms /dev/random blocks if not enough entropy
# is available. This means you then cannot use the /dev/random device
# because it would lead to very long connection times (as long as
# it requires to make more entropy available). But usually those
# platforms additionally provide a /dev/urandom device which doesn't
# block. So, if available, use this one instead. Read the mod_ssl User
# Manual for more details.
#SSLRandomSeed startup file:/dev/random 512
SSLRandomSeed startup file:/dev/urandom 512
#SSLRandomSeed connect file:/dev/random 512
SSLRandomSeed connect file:/dev/urandom 512
# When we also provide SSL we have to listen to the
# standard HTTP port (see above) and to the HTTPS port
Listen 443
## SSL Global Context
## All SSL configuration in this context applies both to
## the main server and all SSL-enabled virtual hosts.
# SSL Cipher Suite:
# List the ciphers that the client is permitted to negotiate.
# See the mod_ssl documentation for a complete list.
SSLCipherSuite HIGH:MEDIUM:!aNULL:!MD5
# Speed-optimized SSL Cipher configuration:
# If speed is your main concern (on busy HTTPS servers e.g.),
# you might want to force clients to specific, performance
# optimized ciphers. In this case, prepend those ciphers
# to the SSLCipherSuite list, and enable SSLHonorCipherOrder.
# Caveat: by giving precedence to RC4-SHA and AES128-SHA
# (as in the example below), most connections will no longer
# have perfect forward secrecy - if the server's key is
# compromised, captures of past or future traffic must be
# considered compromised, too.
#SSLCipherSuite RC4-SHA:AES128-SHA:HIGH:MEDIUM:!aNULL:!MD5
#SSLHonorCipherOrder on
# Pass Phrase Dialog:
# Configure the pass phrase gathering process.
# The filtering dialog program (`builtin' is an internal
# terminal dialog) has to provide the pass phrase on stdout.
SSLPassPhraseDialog builtin
# Inter-Process Session Cache:
# Configure the SSL Session Cache: First the mechanism
# to use and second the expiring timeout (in seconds).
#SSLSessionCache "dbm:/run/httpd/ssl_scache"
SSLSessionCache "shmcb:/run/httpd/ssl_scache(512000)"
SSLSessionCacheTimeout 6000
## SSL Virtual Host Context
<VirtualHost _default_:443>
# General setup for the virtual host
DocumentRoot "/mnt/sda1/svn"
ServerName 192.168.178.48:443
ServerAdmin [email protected]
ErrorLog "/var/log/httpd/error_log"
TransferLog "/var/log/httpd/access_log"
# SSL Engine Switch:
# Enable/Disable SSL for this virtual host.
SSLEngine on
# Server Certificate:
# Point SSLCertificateFile at a PEM encoded certificate. If
# the certificate is encrypted, then you will be prompted for a
# pass phrase. Note that a kill -HUP will prompt again. Keep
# in mind that if you have both an RSA and a DSA certificate you
# can configure both in parallel (to also allow the use of DSA
# ciphers, etc.)
# Some ECC cipher suites (http://www.ietf.org/rfc/rfc4492.txt)
# require an ECC certificate which can also be configured in
# parallel.
SSLCertificateFile "/etc/httpd/conf/server.crt"
#SSLCertificateFile "/etc/httpd/conf/server-dsa.crt"
#SSLCertificateFile "/etc/httpd/conf/server-ecc.crt"
# Server Private Key:
# If the key is not combined with the certificate, use this
# directive to point at the key file. Keep in mind that if
# you've both a RSA and a DSA private key you can configure
# both in parallel (to also allow the use of DSA ciphers, etc.)
# ECC keys, when in use, can also be configured in parallel
SSLCertificateKeyFile "/etc/httpd/conf/server.key"
#SSLCertificateKeyFile "/etc/httpd/conf/server-dsa.key"
#SSLCertificateKeyFile "/etc/httpd/conf/server-ecc.key"
# Server Certificate Chain:
# Point SSLCertificateChainFile at a file containing the
# concatenation of PEM encoded CA certificates which form the
# certificate chain for the server certificate. Alternatively
# the referenced file can be the same as SSLCertificateFile
# when the CA certificates are directly appended to the server
# certificate for convenience.
#SSLCertificateChainFile "/etc/httpd/conf/server-ca.crt"
# Certificate Authority (CA):
# Set the CA certificate verification path where to find CA
# certificates for client authentication or alternatively one
# huge file containing all of them (file must be PEM encoded)
# Note: Inside SSLCACertificatePath you need hash symlinks
# to point to the certificate files. Use the provided
# Makefile to update the hash symlinks after changes.
#SSLCACertificatePath "/etc/httpd/conf/ssl.crt"
#SSLCACertificateFile "/etc/httpd/conf/ssl.crt/ca-bundle.crt"
# Certificate Revocation Lists (CRL):
# Set the CA revocation path where to find CA CRLs for client
# authentication or alternatively one huge file containing all
# of them (file must be PEM encoded).
# The CRL checking mode needs to be configured explicitly
# through SSLCARevocationCheck (defaults to "none" otherwise).
# Note: Inside SSLCARevocationPath you need hash symlinks
# to point to the certificate files. Use the provided
# Makefile to update the hash symlinks after changes.
#SSLCARevocationPath "/etc/httpd/conf/ssl.crl"
#SSLCARevocationFile "/etc/httpd/conf/ssl.crl/ca-bundle.crl"
#SSLCARevocationCheck chain
# Client Authentication (Type):
# Client certificate verification type and depth. Types are
# none, optional, require and optional_no_ca. Depth is a
# number which specifies how deeply to verify the certificate
# issuer chain before deciding the certificate is not valid.
#SSLVerifyClient require
#SSLVerifyDepth 10
# TLS-SRP mutual authentication:
# Enable TLS-SRP and set the path to the OpenSSL SRP verifier
# file (containing login information for SRP user accounts).
# Requires OpenSSL 1.0.1 or newer. See the mod_ssl FAQ for
# detailed instructions on creating this file. Example:
# "openssl srp -srpvfile /etc/httpd/conf/passwd.srpv -add username"
#SSLSRPVerifierFile "/etc/httpd/conf/passwd.srpv"
# Access Control:
# With SSLRequire you can do per-directory access control based
# on arbitrary complex boolean expressions containing server
# variable checks and other lookup directives. The syntax is a
# mixture between C and Perl. See the mod_ssl documentation
# for more details.
#<Location />
#SSLRequire ( %{SSL_CIPHER} !~ m/^(EXP|NULL)/ \
# and %{SSL_CLIENT_S_DN_O} eq "Snake Oil, Ltd." \
# and %{SSL_CLIENT_S_DN_OU} in {"Staff", "CA", "Dev"} \
# and %{TIME_WDAY} >= 1 and %{TIME_WDAY} <= 5 \
# and %{TIME_HOUR} >= 8 and %{TIME_HOUR} <= 20 ) \
# or %{REMOTE_ADDR} =~ m/^192\.76\.162\.[0-9]+$/
#</Location>
# SSL Engine Options:
# Set various options for the SSL engine.
# o FakeBasicAuth:
# Translate the client X.509 into a Basic Authorisation. This means that
# the standard Auth/DBMAuth methods can be used for access control. The
# user name is the `one line' version of the client's X.509 certificate.
# Note that no password is obtained from the user. Every entry in the user
# file needs this password: `xxj31ZMTZzkVA'.
# o ExportCertData:
# This exports two additional environment variables: SSL_CLIENT_CERT and
# SSL_SERVER_CERT. These contain the PEM-encoded certificates of the
# server (always existing) and the client (only existing when client
# authentication is used). This can be used to import the certificates
# into CGI scripts.
# o StdEnvVars:
# This exports the standard SSL/TLS related `SSL_*' environment variables.
# Per default this exportation is switched off for performance reasons,
# because the extraction step is an expensive operation and is usually
# useless for serving static content. So one usually enables the
# exportation for CGI and SSI requests only.
# o StrictRequire:
# This denies access when "SSLRequireSSL" or "SSLRequire" applied even
# under a "Satisfy any" situation, i.e. when it applies access is denied
# and no other module can change it.
# o OptRenegotiate:
# This enables optimized SSL connection renegotiation handling when SSL
# directives are used in per-directory context.
#SSLOptions +FakeBasicAuth +ExportCertData +StrictRequire
<FilesMatch "\.(cgi|shtml|phtml|php)$">
SSLOptions +StdEnvVars
</FilesMatch>
<Directory "/srv/http/cgi-bin">
SSLOptions +StdEnvVars
</Directory>
# SSL Protocol Adjustments:
# The safe and default but still SSL/TLS standard compliant shutdown
# approach is that mod_ssl sends the close notify alert but doesn't wait for
# the close notify alert from client. When you need a different shutdown
# approach you can use one of the following variables:
# o ssl-unclean-shutdown:
# This forces an unclean shutdown when the connection is closed, i.e. no
# SSL close notify alert is sent or allowed to be received. This violates
# the SSL/TLS standard but is needed for some brain-dead browsers. Use
# this when you receive I/O errors because of the standard approach where
# mod_ssl sends the close notify alert.
# o ssl-accurate-shutdown:
# This forces an accurate shutdown when the connection is closed, i.e. a
# SSL close notify alert is send and mod_ssl waits for the close notify
# alert of the client. This is 100% SSL/TLS standard compliant, but in
# practice often causes hanging connections with brain-dead browsers. Use
# this only for browsers where you know that their SSL implementation
# works correctly.
# Notice: Most problems of broken clients are also related to the HTTP
# keep-alive facility, so you usually additionally want to disable
# keep-alive for those clients, too. Use variable "nokeepalive" for this.
# Similarly, one has to force some clients to use HTTP/1.0 to workaround
# their broken HTTP/1.1 implementation. Use variables "downgrade-1.0" and
# "force-response-1.0" for this.
BrowserMatch "MSIE [2-5]" \
nokeepalive ssl-unclean-shutdown \
downgrade-1.0 force-response-1.0
# Per-Server Logging:
# The home of a custom SSL log file. Use this when you want a
# compact non-error SSL logfile on a virtual host basis.
CustomLog "/var/log/httpd/ssl_request_log" \
"%t %h %{SSL_PROTOCOL}x %{SSL_CIPHER}x \"%r\" %b"
#SSLSessionTimeout 5m
Timeout 600000
<Location />
DAV svn
SVNParentPath /mnt/sda1/svn/repos
AuthzSVNAccessFile /home/svn/.svn-policy-file
AuthName "SVN Repositories"
AuthType Basic
AuthUserFile /home/svn/.svn-auth-file
# Satisfy Any
Require valid-user
</Location>
</VirtualHost>
httpd.conf
# This is the main Apache HTTP server configuration file. It contains the
# configuration directives that give the server its instructions.
# See <URL:http://httpd.apache.org/docs/2.4/> for detailed information.
# In particular, see
# <URL:http://httpd.apache.org/docs/2.4/mod/directives.html>
# for a discussion of each configuration directive.
# Do NOT simply read the instructions in here without understanding
# what they do. They're here only as hints or reminders. If you are unsure
# consult the online docs. You have been warned.
# Configuration and logfile names: If the filenames you specify for many
# of the server's control files begin with "/" (or "drive:/" for Win32), the
# server will use that explicit path. If the filenames do *not* begin
# with "/", the value of ServerRoot is prepended -- so "logs/access_log"
# with ServerRoot set to "/usr/local/apache2" will be interpreted by the
# server as "/usr/local/apache2/logs/access_log", whereas "/logs/access_log"
# will be interpreted as '/logs/access_log'.
# ServerRoot: The top of the directory tree under which the server's
# configuration, error, and log files are kept.
# Do not add a slash at the end of the directory path. If you point
# ServerRoot at a non-local disk, be sure to specify a local disk on the
# Mutex directive, if file-based mutexes are used. If you wish to share the
# same ServerRoot for multiple httpd daemons, you will need to change at
# least PidFile.
ServerRoot "/etc/httpd"
Timeout 60000
# Mutex: Allows you to set the mutex mechanism and mutex file directory
# for individual mutexes, or change the global defaults
# Uncomment and change the directory if mutexes are file-based and the default
# mutex file directory is not on a local disk or is not appropriate for some
# other reason.
# Mutex default:/run/httpd
# Listen: Allows you to bind Apache to specific IP addresses and/or
# ports, instead of the default. See also the <VirtualHost>
# directive.
# Change this to Listen on specific IP addresses as shown below to
# prevent Apache from glomming onto all bound IP addresses.
#Listen 12.34.56.78:80
Listen 80
# Dynamic Shared Object (DSO) Support
# To be able to use the functionality of a module which was built as a DSO you
# have to place corresponding `LoadModule' lines at this location so the
# directives contained in it are actually available _before_ they are used.
# Statically compiled modules (those listed by `httpd -l') do not need
# to be loaded here.
# Example:
# LoadModule foo_module modules/mod_foo.so
LoadModule authn_file_module modules/mod_authn_file.so
#LoadModule authn_dbm_module modules/mod_authn_dbm.so
#LoadModule authn_anon_module modules/mod_authn_anon.so
#LoadModule authn_dbd_module modules/mod_authn_dbd.so
#nach fehlermeldung
LoadModule authn_socache_module modules/mod_authn_socache.so
LoadModule authn_core_module modules/mod_authn_core.so
LoadModule authz_host_module modules/mod_authz_host.so
LoadModule authz_groupfile_module modules/mod_authz_groupfile.so
LoadModule authz_user_module modules/mod_authz_user.so
#LoadModule authz_dbm_module modules/mod_authz_dbm.so
#LoadModule authz_owner_module modules/mod_authz_owner.so
#LoadModule authz_dbd_module modules/mod_authz_dbd.so
LoadModule authz_core_module modules/mod_authz_core.so
#LoadModule authnz_ldap_module modules/mod_authnz_ldap.so
LoadModule access_compat_module modules/mod_access_compat.so
LoadModule auth_basic_module modules/mod_auth_basic.so
#LoadModule auth_form_module modules/mod_auth_form.so
#LoadModule auth_digest_module modules/mod_auth_digest.so
#LoadModule allowmethods_module modules/mod_allowmethods.so
#LoadModule file_cache_module modules/mod_file_cache.so
#Felhermeldung undefined symbols
LoadModule cache_module modules/mod_cache.so
#LoadModule cache_disk_module modules/mod_cache_disk.so
#nach Fehlermeldung
LoadModule cache_socache_module modules/mod_cache_socache.so
#nochne Fehlermeldung
LoadModule socache_shmcb_module modules/mod_socache_shmcb.so
#LoadModule socache_dbm_module modules/mod_socache_dbm.so
#LoadModule socache_memcache_module modules/mod_socache_memcache.so
#LoadModule watchdog_module modules/mod_watchdog.so
#LoadModule macro_module modules/mod_macro.so
#LoadModule dbd_module modules/mod_dbd.so
#LoadModule dumpio_module modules/mod_dumpio.so
#LoadModule echo_module modules/mod_echo.so
#LoadModule buffer_module modules/mod_buffer.so
#LoadModule data_module modules/mod_data.so
#LoadModule ratelimit_module modules/mod_ratelimit.so
LoadModule reqtimeout_module modules/mod_reqtimeout.so
#LoadModule ext_filter_module modules/mod_ext_filter.so
#LoadModule request_module modules/mod_request.so
LoadModule include_module modules/mod_include.so
LoadModule filter_module modules/mod_filter.so
#LoadModule reflector_module modules/mod_reflector.so
#LoadModule substitute_module modules/mod_substitute.so
#LoadModule sed_module modules/mod_sed.so
#LoadModule charset_lite_module modules/mod_charset_lite.so
#LoadModule deflate_module modules/mod_deflate.so
#LoadModule xml2enc_module modules/mod_xml2enc.so
#LoadModule proxy_html_module modules/mod_proxy_html.so
LoadModule mime_module modules/mod_mime.so
#LoadModule ldap_module modules/mod_ldap.so
LoadModule log_config_module modules/mod_log_config.so
#LoadModule log_debug_module modules/mod_log_debug.so
#LoadModule log_forensic_module modules/mod_log_forensic.so
#LoadModule logio_module modules/mod_logio.so
#LoadModule lua_module modules/mod_lua.so
LoadModule env_module modules/mod_env.so
#LoadModule mime_magic_module modules/mod_mime_magic.so
#LoadModule cern_meta_module modules/mod_cern_meta.so
#LoadModule expires_module modules/mod_expires.so
LoadModule headers_module modules/mod_headers.so
#LoadModule ident_module modules/mod_ident.so
#LoadModule usertrack_module modules/mod_usertrack.so
#LoadModule unique_id_module modules/mod_unique_id.so
LoadModule setenvif_module modules/mod_setenvif.so
LoadModule version_module modules/mod_version.so
#LoadModule remoteip_module modules/mod_remoteip.so
LoadModule proxy_module modules/mod_proxy.so
LoadModule proxy_connect_module modules/mod_proxy_connect.so
LoadModule proxy_ftp_module modules/mod_proxy_ftp.so
LoadModule proxy_http_module modules/mod_proxy_http.so
LoadModule proxy_fcgi_module modules/mod_proxy_fcgi.so
LoadModule proxy_scgi_module modules/mod_proxy_scgi.so
#LoadModule proxy_fdpass_module modules/mod_proxy_fdpass.so
LoadModule proxy_wstunnel_module modules/mod_proxy_wstunnel.so
LoadModule proxy_ajp_module modules/mod_proxy_ajp.so
LoadModule proxy_balancer_module modules/mod_proxy_balancer.so
LoadModule proxy_express_module modules/mod_proxy_express.so
#LoadModule session_module modules/mod_session.so
#LoadModule session_cookie_module modules/mod_session_cookie.so
#LoadModule session_crypto_module modules/mod_session_crypto.so
#LoadModule session_dbd_module modules/mod_session_dbd.so
LoadModule slotmem_shm_module modules/mod_slotmem_shm.so
#LoadModule slotmem_plain_module modules/mod_slotmem_plain.so
#Fuer die cipher suite
LoadModule ssl_module modules/mod_ssl.so
#LoadModule dialup_module modules/mod_dialup.so
LoadModule lbmethod_byrequests_module modules/mod_lbmethod_byrequests.so
LoadModule lbmethod_bytraffic_module modules/mod_lbmethod_bytraffic.so
LoadModule lbmethod_bybusyness_module modules/mod_lbmethod_bybusyness.so
LoadModule lbmethod_heartbeat_module modules/mod_lbmethod_heartbeat.so
LoadModule mpm_event_module modules/mod_mpm_event.so
LoadModule unixd_module modules/mod_unixd.so
#LoadModule heartbeat_module modules/mod_heartbeat.so
#LoadModule heartmonitor_module modules/mod_heartmonitor.so
#1 for svn
LoadModule dav_module modules/mod_dav.so
LoadModule status_module modules/mod_status.so
LoadModule autoindex_module modules/mod_autoindex.so
#LoadModule asis_module modules/mod_asis.so
#LoadModule info_module modules/mod_info.so
#LoadModule suexec_module modules/mod_suexec.so
#LoadModule cgid_module modules/mod_cgid.so
#LoadModule cgi_module modules/mod_cgi.so
#2 for svn
LoadModule dav_fs_module modules/mod_dav_fs.so
#LoadModule dav_lock_module modules/mod_dav_lock.so
#LoadModule vhost_alias_module modules/mod_vhost_alias.so
LoadModule negotiation_module modules/mod_negotiation.so
LoadModule dir_module modules/mod_dir.so
#LoadModule imagemap_module modules/mod_imagemap.so
#LoadModule actions_module modules/mod_actions.so
#LoadModule speling_module modules/mod_speling.so
LoadModule userdir_module modules/mod_userdir.so
LoadModule alias_module modules/mod_alias.so
#LoadModule rewrite_module modules/mod_rewrite.so
#3 for svn
LoadModule dav_svn_module modules/mod_dav_svn.so
LoadModule authz_svn_module modules/mod_authz_svn.so
<IfModule unixd_module>
# If you wish httpd to run as a different user or group, you must run
# httpd as root initially and it will switch.
# User/Group: The name (or #number) of the user/group to run httpd as.
# It is usually good practice to create a dedicated user and group for
# running httpd, as with most system services.
User http
Group http
</IfModule>
# 'Main' server configuration
# The directives in this section set up the values used by the 'main'
# server, which responds to any requests that aren't handled by a
# <VirtualHost> definition. These values also provide defaults for
# any <VirtualHost> containers you may define later in the file.
# All of these directives may appear inside <VirtualHost> containers,
# in which case these default settings will be overridden for the
# virtual host being defined.
# ServerAdmin: Your address, where problems with the server should be
# e-mailed. This address appears on some server-generated pages, such
# as error documents. e.g. [email protected]
ServerAdmin [email protected]
# ServerName gives the name and port that the server uses to identify itself.
# This can often be determined automatically, but we recommend you specify
# it explicitly to prevent problems during startup.
# If your host doesn't have a registered DNS name, enter its IP address here.
#ServerName www.example.com:80
# Deny access to the entirety of your server's filesystem. You must
# explicitly permit access to web content directories in other
# <Directory> blocks below.
<Directory />
AllowOverride none
Require all denied
</Directory>
# Note that from this point forward you must specifically allow
# particular features to be enabled - so if something's not working as
# you might expect, make sure that you have specifically enabled it
# below.
# DocumentRoot: The directory out of which you will serve your
# documents. By default, all requests are taken from this directory, but
# symbolic links and aliases may be used to point to other locations.
DocumentRoot "/mnt/sda1"
#<Directory "/mnt/sda1/svn/repos">
# # Possible values for the Options directive are "None", "All",
# # or any combination of:
# # Indexes Includes FollowSymLinks SymLinksifOwnerMatch ExecCGI MultiViews
# # Note that "MultiViews" must be named *explicitly* --- "Options All"#
# # doesn't give it to you.
# # The Options directive is both complicated and important. Please see
# # http://httpd.apache.org/docs/2.4/mod/core.html#options
# # for more information.#
# Options Indexes FollowSymLinks
# # AllowOverride controls what directives may be placed in .htaccess files.
# # It can be "All", "None", or any combination of the keywords:
# # AllowOverride FileInfo AuthConfig Limit
# AllowOverride None
# # Controls who can get stuff from this server.
# Require all granted
#</Directory>
# DirectoryIndex: sets the file that Apache will serve if a directory
# is requested.
<IfModule dir_module>
DirectoryIndex index.html
</IfModule>
# The following lines prevent .htaccess and .htpasswd files from being
# viewed by Web clients.
<Files ".ht*">
Require all denied
</Files>
# ErrorLog: The location of the error log file.
# If you do not specify an ErrorLog directive within a <VirtualHost>
# container, error messages relating to that virtual host will be
# logged here. If you *do* define an error logfile for a <VirtualHost>
# container, that host's errors will be logged there and not here.
ErrorLog "/var/log/httpd/error_log"
# LogLevel: Control the number of messages logged to the error_log.
# Possible values include: debug, info, notice, warn, error, crit,
# alert, emerg.
LogLevel warn
<IfModule log_config_module>
# The following directives define some format nicknames for use with
# a CustomLog directive (see below).
LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" combined
LogFormat "%h %l %u %t \"%r\" %>s %b" common
<IfModule logio_module>
# You need to enable mod_logio.c to use %I and %O
LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\" %I %O" combinedio
</IfModule>
# The location and format of the access logfile (Common Logfile Format).
# If you do not define any access logfiles within a <VirtualHost>
# container, they will be logged here. Contrariwise, if you *do*
# define per-<VirtualHost> access logfiles, transactions will be
# logged therein and *not* in this file.
CustomLog "/var/log/httpd/access_log" common
# If you prefer a logfile with access, agent, and referer information
# (Combined Logfile Format) you can use the following directive.
#CustomLog "/var/log/httpd/access_log" combined
</IfModule>
<IfModule alias_module>
# Redirect: Allows you to tell clients about documents that used to
# exist in your server's namespace, but do not anymore. The client
# will make a new request for the document at its new location.
# Example:
# Redirect permanent /foo http://www.example.com/bar
# Alias: Maps web paths into filesystem paths and is used to
# access content that does not live under the DocumentRoot.
# Example:
# Alias /webpath /full/filesystem/path
# If you include a trailing / on /webpath then the server will
# require it to be present in the URL. You will also likely
# need to provide a <Directory> section to allow access to
# the filesystem path.
# ScriptAlias: This controls which directories contain server scripts.
# ScriptAliases are essentially the same as Aliases, except that
# documents in the target directory are treated as applications and
# run by the server when requested rather than as documents sent to the
# client. The same rules about trailing "/" apply to ScriptAlias
# directives as to Alias.
ScriptAlias /cgi-bin/ "/srv/http/cgi-bin/"
</IfModule>
<IfModule cgid_module>
# ScriptSock: On threaded servers, designate the path to the UNIX
# socket used to communicate with the CGI daemon of mod_cgid.
#Scriptsock cgisock
</IfModule>
# "/srv/http/cgi-bin" should be changed to whatever your ScriptAliased
# CGI directory exists, if you have that configured.
<Directory "/srv/http/cgi-bin">
AllowOverride None
Options None
Require all granted
</Directory>
<IfModule mime_module>
# TypesConfig points to the file containing the list of mappings from
# filename extension to MIME-type.
TypesConfig conf/mime.types
# AddType allows you to add to or override the MIME configuration
# file specified in TypesConfig for specific file types.
#AddType application/x-gzip .tgz
# AddEncoding allows you to have certain browsers uncompress
# information on the fly. Note: Not all browsers support this.
#AddEncoding x-compress .Z
#AddEncoding x-gzip .gz .tgz
# If the AddEncoding directives above are commented-out, then you
# probably should define those extensions to indicate media types:
AddType application/x-compress .Z
AddType application/x-gzip .gz .tgz
# AddHandler allows you to map certain file extensions to "handlers":
# actions unrelated to filetype. These can be either built into the server
# or added with the Action directive (see below)
# To use CGI scripts outside of ScriptAliased directories:
# (You will also need to add "ExecCGI" to the "Options" directive.)
#AddHandler cgi-script .cgi
# For type maps (negotiated resources):
#AddHandler type-map var
# Filters allow you to process content before it is sent to the client.
# To parse .shtml files for server-side includes (SSI):
# (You will also need to add "Includes" to the "Options" directive.)
#AddType text/html .shtml
#AddOutputFilter INCLUDES .shtml
</IfModule>
# The mod_mime_magic module allows the server to use various hints from the
# contents of the file itself to determine its type. The MIMEMagicFile
# directive tells the module where the hint definitions are located.
#MIMEMagicFile conf/magic
# Customizable error responses come in three flavors:
# 1) plain text 2) local redirects 3) external redirects
# Some examples:
#ErrorDocument 500 "The server made a boo boo."
#ErrorDocument 404 /missing.html
#ErrorDocument 404 "/cgi-bin/missing_handler.pl"
#ErrorDocument 402 http://www.example.com/subscription_info.html
# MaxRanges: Maximum number of Ranges in a request before
# returning the entire resource, or one of the special
# values 'default', 'none' or 'unlimited'.
# Default setting is to accept 200 Ranges.
#MaxRanges unlimited
# EnableMMAP and EnableSendfile: On systems that support it,
# memory-mapping or the sendfile syscall may be used to deliver
# files. This usually improves server performance, but must
# be turned off when serving from networked-mounted
# filesystems or if support for these functions is otherwise
# broken on your system.
# Defaults: EnableMMAP On, EnableSendfile Off
#EnableMMAP off
#EnableSendfile on
# Supplemental configuration
# The configuration files in the conf/extra/ directory can be
# included to add extra features or to modify the default configuration of
# the server, or you may simply copy their contents here and change as
# necessary.
# Server-pool management (MPM specific)
Include conf/extra/httpd-mpm.conf
# Multi-language error messages
Include conf/extra/httpd-multilang-errordoc.conf
# Fancy directory listings
Include conf/extra/httpd-autoindex.conf
# Language settings
Include conf/extra/httpd-languages.conf
# User home directories
Include conf/extra/httpd-userdir.conf
# Real-time info on requests and configuration
#Include conf/extra/httpd-info.conf
# Virtual hosts
#Include conf/extra/httpd-vhosts.conf
# Local access to the Apache HTTP Server Manual
#Include conf/extra/httpd-manual.conf
# Distributed authoring and versioning (WebDAV)
#Include conf/extra/httpd-dav.conf
# Various default settings
Include conf/extra/httpd-default.conf
# Configure mod_proxy_html to understand HTML4/XHTML1
<IfModule proxy_html_module>
Include conf/extra/proxy-html.conf
</IfModule>
# Secure (SSL/TLS) connections
Include /etc/httpd/conf/extra/httpd-ssl.conf
# Note: The following must must be present to support
# starting without SSL on platforms with no /dev/random equivalent
# but a statically compiled-in mod_ssl.
<IfModule ssl_module>
SSLRandomSeed startup builtin
SSLRandomSeed connect builtin
</IfModule>
# uncomment out the below to deal with user agents that deliberately
# violate open standards by misusing DNT (DNT *must* be a specific
# end-user choice)
#<IfModule setenvif_module>
#BrowserMatch "MSIE 10.0;" bad_DNT
#</IfModule>
#<IfModule headers_module>
#RequestHeader unset DNT env=bad_DNT
#</IfModule>
Edit: inserted tl;dr
Last edited by arch_on_pi (2014-05-18 21:33:24)Remember that Arch Arm is a different distribution, but we try to bend the rules and provide limited support for them. This may or may not be unique to Arch Arm, so you might try asking on their forums as well.
-
Issue with script timeouts - trying to send email mail shots - hosting recommendations?
Background is this - I look after a site for a recruitment agency, which has a backend mySQL database.
It includes a table of potential candidates, which the site owner can search based on various criteria and then send all the returned candidates an email about potential jobs they might be interested in.
I'm using an off the shelf script to send the emails, and have jumped through a few hoops to get this to work, but it looks like we need to move hosting unfortunately.
The script is able to limit emails so that the hosting company doesn't get black flagged as a spammer.
I've set it up with a progress bar in a new window so the site owner can see progress, but easily get back to the rest of the site.
But where we have come unstuck is the script timeout on the server - so even though its set to send emails slowly enough, ie under 500 emails an hour, because of that slow pace, it fails if it takes more then five minutes to send them all as the script times out.
My understanding is that the script includes a line to reset the script timeout value to 0, so enabling the script to keep running until all the emails have been sent. But unfortunately our current hosting company does not allow the script timeout to be reset at the PHP level.
So my question is this - is anyone doing anything similar, and if so, can you recommend any hosting company that does allow the script timeout to be reset at the PHP level?
Because at the minute it seems like a frustrating catch-22 - slow it down to get around the spam issue, and it won't run long enough to send all the emails. Speed it up, and it falls foul of the script timeout.
Any advise on this, or hosting suggestons most welcome!
Thanks.Although there is an AppleScript Forum, Automator can run AppleScripts, so sometimes things can go in either forum. In your script, other than not setting a recipient, you are just getting one of the persons. You need to get a list of your contact information, then build your outgoing messages from that list - for example:
<pre style="
font-family: Monaco, 'Courier New', Courier, monospace;
font-size: 10px;
font-weight: normal;
margin: 0px;
padding: 5px;
border: 1px solid #000000;
width: 720px; height: 340px;
color: #000000;
background-color: #FFEE80;
overflow: auto;"
title="this text can be pasted into the Script Editor">
set theEmails to {} -- this will be a list of email addresses
set theNames to {} -- this will be a list of names for the greeting
tell application "Address Book"
activate
set theGroup to (choose from list (get the name of every group) with prompt "Choose a Group") as text
if theGroup is "false" then return -- cancel
repeat with aPerson in (get every person of group theGroup) -- build email and name lists
set the end of theEmails to the first item of (get the value of the email of aPerson) -- just the first address
set the end of theNames to the first name of aPerson
end repeat
end tell
tell application "Mail"
repeat with anItem from 1 to (count theEmails) -- make a new message for each entry
tell (make new outgoing message at the front of outgoing messages with properties {subject:"Test Mail"})
set visible to true
get item anItem of theNames
if the result is missing value then -- no name
set the content to "message"
else
set the content to "Dear " & the result & "," & return & return & "message"
end if
make new to recipient at the end of to recipients with properties {address:(item anItem of theEmails)}
end tell
end repeat
activate
end tell
</pre> -
"agesani Initialize With Options" timeout error on HP E4401B spectrum analyzer
System: Windows XP Pro, LabVIEW 7.1, IVI Compliance Package 3.0, NI-VISA 4.1
I have an HP E4401B Spectrum Analyzer. I'm trying to write some LabVIEW code for it, using the agesani.llb library.
When I try using the agesani Initialize With Options VI, I get the following error:
Error code: BFFF0015
Source: agesani Initialize WIth Options.vi<ERR>Driver Status: (Hex 0xBFFF0015) Primary Error: (Hex 0xBFFF0015) Timeout expired before operation completed.
I've searched the NI Knowlege Base, and haven't found anything that seems useful. What I _have_ found are the following items.
Knowlege Base article "Time-Out Error with the Agesa Instrument Driver Example". This refers to the agesa drivers, not the agesani drivers. It also references an E4440A spectrum analyzer, not an E4401B. The article says one cause could be that a compatibility mode other that SCPI is in use. While the articles says how to fix this on an E4440A, the fix does not appear to apply to the E4401B. In fact, if it is even _possible_ to have a mode other than SCPI on an E4401B, I can't figure out how to do it. A second possibility the article suggests is that the spectrum analyzer is in Phase Noise mode rather than Spectrum Analyzer mode. My E4401B is in SA (spectrum analyzer) mode. I don't even see a way to put it in any other mode - I don't think the required options are installed. Finally, my VI is configured as the article states - ID Query YES, Reset Device YES, etc. I should note that the instrument's GPIB address is 18, and that this matches the resource name GPIO0::18::INSTR.
Some additional information: The spectrum analyzer's screen is indicating the instrument is in Remote (R) mode as a Talker (T). A "Query UNTERMINATED" error message appears at the bottom of the instrument screen.
I've attached the results of a NI Spy capture to this message. (At least, I think I have. I've never tried doing this before, so if it doesn't show up, would some kind soul tell me how to include an attachment to my post?)
Oh, yes. The agesani version is driver version 1.1, updated 17 Aug 2007. (The version that's currently on the NI download site.)
Attachments:
Capture4.spy 9 KBHi MXI Master,
If there's an instrument timeout, I haven't been able to find it yet. Seems like there should be, so maybe I just haven't looked in the right place yet. As for the timeout value on the computer, I'm not sure what you mean by this - could you elaborate, and maybe tell me where to find it?
As far as SCPI mode, if it's possible to put the E4401B in something _other_ than SCPI mode, I haven't figured out how. I can't find any support in the programming manual for anything other than SCPI.
That kind of seques into my next couple points. The NI Spy output indicates that one of the commands that is being sent is "*SRE 32".
The "User's & Programmer's Reference" for the E4401B says (on page 206) "Send the *SRE <number> command (where <number> is the sum of the decimal values of the bits you want to enable plus the decimal value of bit 6). [Bit 6 is the Request Service (RQS) Summary Bit. BP] For example, assume that you want to enable bit 7 so that whenever the operation status summary bit is set to 1, it will trigger a service request. Send the *SRE 192 (128 + 64) command."
This statement would seem to imply that the "*SRE 32" command that is being sent by the agesani "Initialize With Options" command is an illegal command, or at best an ineffective command. In light of that, it is interesting to me that the NI Spy output indicates that the next line , viQuery(GPIB::18::INSTR (0x246E9C8), "%s?","%ld"), is generating an 0xBFFF0015 error. In addition, I can find neither the "%s?" nor the "%ld" commands listed in the Programmer's Reference. I wonder if these could be for a firmware revision later than mine (A.01.03), or for instrument options I don't have (A4H, A4J). Alternatively, I wonder if these are simply mistakes.
The next line in the NI Spy output, Formatted viWrite(CPIB0::18::INSTR (0x0246E9C89),"INST:NSEL?",11,11), also puzzles me. The Programmer's Reference indicates that this is a supported command, to see what instrument application is currently selected. (e.g. spectrum analyzer, GSM, Bluetooth, EDGE, noise figure, etc.) However, when I try to issue this command to my instrument, by using the Instrument I/O Assistant Express VI, I get an "Undefined header" error on the instrument's front panel. The instrument's error history shows the same "Undefined header" error. Since my instrument only has the basic spectrum analyzer option installed, I wonder if this command is not valid? (Personally, I wouldn't write instrument firmware code this way, but who knows?) Alternatively, I wonder if this command requires a firmware revision more recent than mine. (The Programmer's Reference is silent about this possibility.)
The next line in the NI Spy output, Formatted viRead(GPIB::18::INSTR (0x0246E9C8),"",4000,0), has another 0XBFFF0015 error associated with it.
Does this information shed any more light on the situation? -
Full Deployment failing with Transaction timeout
Hi
I am trying to do a full deployment(ATG 10.0.2) and its failing with the same transaction timeout on all environments (local, dev, stage)
I have tried to reduce the maxThreads to 1 in DeploymentManager but still i get the same exception.
Incremental deployments seems to be running fine if i deploy anything, like category, products, skus.
Even the catalog feed runs and deploys fine.
I have a total of around 1500 products and 7000 skus.
In BCC screen i see it gives timeout while deploying skus
Error Deployment Failed 1051226:sku 2011-08-27 20:04:02.798
Message Detail:
CONTAINER:atg.deployment.DistributedDeploymentException; SOURCE:CONTAINER:atg.repository.RepositoryException; SOURCE:org.jboss.util.NestedSQLException: Transaction is not active: tx=TransactionImple < ac, BasicAction: ada0e22:4593:4e59847c:5e57e8 status: ActionStatus.ABORTING >; - nested throwable: (javax.resource.ResourceException: Transaction is not active: tx=TransactionImple < ac, BasicAction: ada0e22:4593:4e59847c:5e57e8 status: ActionStatus.ABORTING >) at atg.deployment.repository.RepositoryWorkerThread.processMarkerForReferenceUpdatePhase(RepositoryWorkerThread.java:346) at atg.deployment.DeploymentWorkerThread.processMarkerPhase(DeploymentWorkerThread.java:540) at atg.deployment.DeploymentWorkerThread.run(DeploymentWorkerThread.java:307)
In the logs i see the following exceptions::
20:03:54,827 WARN [arjLoggerI18N] [com.arjuna.ats.arjuna.coordinator.BasicAction_58] - Abort of action id ada0e22:4593:4e59847c:5e57e8 invoked while multiple threads a
ctive within it.
20:03:54,827 WARN [arjLoggerI18N] [com.arjuna.ats.arjuna.coordinator.CheckedAction_2] - CheckedAction::check - atomic action ada0e22:4593:4e59847c:5e57e8 aborting with
1 threads active!
20:03:55,329 WARN [arjLoggerI18N] [com.arjuna.ats.arjuna.coordinator.TransactionReaper_18] - TransactionReaper::check timeout for TX ada0e22:4593:4e59847c:5e57e8 in st
ate CANCEL
20:03:55,831 WARN [arjLoggerI18N] [com.arjuna.ats.arjuna.coordinator.TransactionReaper_18] - TransactionReaper::check timeout for TX ada0e22:4593:4e59847c:5e57e8 in st
ate CANCEL_INTERRUPTED
20:03:55,831 WARN [arjLoggerI18N] [com.arjuna.ats.arjuna.coordinator.TransactionReaper_6] - TransactionReaper::check worker Thread[Thread-138,5,jboss] not responding t
o interrupt when cancelling TX ada0e22:4593:4e59847c:5e57e8 -- worker marked as zombie and TX scheduled for mark-as-rollback
20:03:55,831 WARN [arjLoggerI18N] [com.arjuna.ats.arjuna.coordinator.TransactionReaper_11] - TransactionReaper::check failed to mark TX ada0e22:4593:4e59847c:5e57e8 a
s rollback only
20:04:01,934 INFO [DeploymentManager] DEBUG RepositoryWorkerThread-1(Reference Update Phase) Rolling Back Current Transaction
20:04:02,021 WARN [arjLoggerI18N] [com.arjuna.ats.arjuna.coordinator.BasicAction_40] - Abort called on already aborted atomic action ada0e22:4593:4e59847c:5e57e8
20:04:02,022 WARN [arjLoggerI18N] [com.arjuna.ats.arjuna.coordinator.TransactionReaper_13] - TransactionReaper::doCancellations worker Thread[Thread-138,5,jboss] misse
d interrupt when cancelling TX ada0e22:4593:4e59847c:5e57e8 -- exiting as zombie (zombie count decremented to 0)
20:04:02,023 INFO [DeploymentManager] DEBUG RepositoryWorkerThread-1(Reference Update Phase) Committing 237 markers, 1 failed markers
20:04:02,798 ERROR [DeploymentManager] item = repositoryMarker:mark876015 cause = CONTAINER:atg.deployment.DistributedDeploymentException; SOURCE:CONTAINER:atg.reposit
ory.RepositoryException; SOURCE:org.jboss.util.NestedSQLException: Transaction is not active: tx=TransactionImple < ac, BasicAction: ada0e22:4593:4e59847c:5e57e8 status
: ActionStatus.ABORTING >; - nested throwable: (javax.resource.ResourceException: Transaction is not active: tx=TransactionImple < ac, BasicAction: ada0e22:4593:4e59847
c:5e57e8 status: ActionStatus.ABORTING >)
at atg.deployment.repository.RepositoryWorkerThread.processMarkerForReferenceUpdatePhase(RepositoryWorkerThread.java:346)
at atg.deployment.DeploymentWorkerThread.processMarkerPhase(DeploymentWorkerThread.java:540)
at atg.deployment.DeploymentWorkerThread.run(DeploymentWorkerThread.java:307)
message = Deployment Failed time = Sat Aug 27 20:04:02 MDT 2011 atg.deployment.DeploymentFailure@2be5134e
CAUGHT AT:
CONTAINER:atg.deployment.DistributedDeploymentException; SOURCE:CONTAINER:atg.repository.RepositoryException; SOURCE:org.jboss.util.NestedSQLException: Transaction is n
ot active: tx=TransactionImple < ac, BasicAction: ada0e22:4593:4e59847c:5e57e8 status: ActionStatus.ABORTING >; - nested throwable: (javax.resource.ResourceException: T
ransaction is not active: tx=TransactionImple < ac, BasicAction: ada0e22:4593:4e59847c:5e57e8 status: ActionStatus.ABORTING >)
at atg.deployment.repository.RepositoryWorkerThread.processMarkerForReferenceUpdatePhase(RepositoryWorkerThread.java:346)
20:04:02,992 INFO [DeploymentManager] DEBUG RepositoryWorkerThread-1(Reference Update Phase) Failure count was: 0. New failure count is: 1.
20:04:02,995 INFO [DeploymentManager] DEBUG RepositoryWorkerThread-1(Reference Update Phase) Rolling Back Current Transaction
20:04:02,995 INFO [DeploymentManager] DEBUG RepositoryWorkerThread-1(Reference Update Phase) Committing 0 markers, 0 failed markers
20:04:03,152 INFO [DeploymentManager] DEBUG RepositoryWorkerThread-1(Reference Update Phase) Exiting normally
20:04:03,153 ERROR [DeploymentManager] Unexpected error occurred. DeploymentWorkerThread terminated prematurely.
atg.deployment.DistributedDeploymentException: Exceeded allowable error count (0)
at atg.deployment.DeploymentWorkerThread.processMarkerPhase(DeploymentWorkerThread.java:652)
at atg.deployment.DeploymentWorkerThread.run(DeploymentWorkerThread.java:307)
20:04:07,724 INFO [DeploymentServer] DEBUG 1500007:Production:atg.deployment.adapter.DistributedDeploymentAdapter.displayDeploymentFailures(DistributedDeploymentAdapte
r.java:2652) found 1 failure messages
20:04:07,747 INFO [DeploymentServer] DEBUG 1500007:Production:atg.deployment.adapter.DistributedDeploymentAdapter.displayDeploymentFailures(DistributedDeploymentAdapte
r.java:2683) adding failure message Deployment Failed with severity Error
20:04:11,211 INFO [DeploymentManager] DEBUG Main deployment thread: No waiting deployments to start
20:04:11,240 INFO [DeploymentServer] DEBUG 1500007:Production:atg.deployment.adapter.DistributedDeploymentAdapter.deploymentFailed(DistributedDeploymentAdapter.java:31
86) DeploymentListener.deploymentFailed called for deployment with ID: 1500007
20:04:11,240 INFO [DeploymentServer] DEBUG 1500007:Production:atg.deployment.adapter.DistributedDeploymentAdapter.deploymentFailed(DistributedDeploymentAdapter.java:31
94) DAFDeploymentID: 1500007 matches DeploymmentID: 1500007
20:04:11,240 INFO [DeploymentServer] DEBUG 1500007:Production:atg.deployment.adapter.DistributedDeploymentAdapter.deploymentFailed(DistributedDeploymentAdapter.java:31
98) DeploymentListener.deploymentFailed
20:04:11,241 INFO [DeploymentServer] DEBUG 1500007:Production:atg.deployment.adapter.DistributedDeploymentAdapter.displayDeploymentFailures(DistributedDeploymentAdapte
r.java:2652) found 1 failure messages
20:04:11,259 INFO [DeploymentServer] DEBUG 1500007:Production:atg.deployment.adapter.DistributedDeploymentAdapter.displayDeploymentFailures(DistributedDeploymentAdapte
r.java:2683) adding failure message Deployment Failed with severity Error
20:04:11,261 INFO [DeploymentServer] DEBUG 1500007:Production:atg.deployment.adapter.DistributedDeploymentAdapter.deployData(DistributedDeploymentAdapter.java:2197)
deployment failed
20:04:11,386 ERROR [DeploymentServer]
atg.deployment.common.DeploymentException: Deployment '1500007' to target 'Production' encountered a system level deployment error during data transfer.
at atg.deployment.common.ResourceUtil.exception(ResourceUtil.java:306)
at atg.deployment.adapter.DistributedDeploymentAdapter.deployData(DistributedDeploymentAdapter.java:2238)
at atg.deployment.adapter.DistributedDeploymentAdapter.transferData(DistributedDeploymentAdapter.java:305)
at atg.deployment.server.Deployment.run(Deployment.java:1688)I am using ATG10.0.2 with jboss-5.1-eap
I have tried increasing the timeout on jboss, but it only stops the timeout from happening, but the full deployment takes forever and takes more than 12 hours.
The catalog itself is too small and shouldnt be taking that much at all.
I just checked one thing:
I have a one to many relation with my sku and sale price(custom table) which has 11000 rows. If i delete the data in this table the deployment happens fine and takes about 30 mins.
The relationship it self seems correct.
this is on sku descriptor
<table name="my_sku_saleprice" type="multi" id-column-name="sku_id">
<property name="salePrices" column-name="sale_prices" data-type="set" component-item-type="salePrices" display-name-resource="salePrices"
writable="true" category-resource="categoryPresentation">
<attribute name="resourceBundle" value="atg.projects.store.StoreCatalogTemplateResources"/>
</property>
</table>
And this is the salePrices descriptor
<item-descriptor name="salePrices" display-name-resource="itemDescriptorSalePrices"
item-cache-size="100000" query-cache-size="100000">
<attribute name="resourceBundle" value="atg.projects.store.StoreCatalogTemplateResources"/>
<table name="my_sku_saleprices" type="primary" id-column-name="sale_prices">
<property name="salesPrice" data-type="double" column-name="sales_price" required="true" display-name-resource="salesPrice"/>
<property name="saleType" data-type="string" column-name="sale_type" required="true" display-name-resource="saleType"/>
<property name="startDate" data-type="Date" column-name="start_date" display-name-resource="startDate"/>
<property name="endDate" data-type="Date" column-name="end_date" display-name-resource="endDate"/>
</table>
</item-descriptor>
The only thing i m not able to understand is why its taking forever to get the full deployment.
Incremental deployment in catalog happens quickly, if i deploy any sku,product or anything.
Is it something to do with ATG or jboss?
Any pointers will help
Thanks -
Dealing with hard timeout of guarded service
Hi, I'm investigating the behavior the cause of and subsequent behavior after a hard timeout of a guarded service. In my experience, the grid members are unable to recover properly. I am trying to figure out whether there is something in our configuration that may be aggravating the situation, and also see whether I might be able to improve the behavior of our client code.
What I have done is purposely lower the service guardian's timeout, to about 25 seconds, so that a certain EntryProcessor will always time-out. The behavior I see after the timeout is very similar to the behavior we see when the problem crops up in the real world. I know that I can raise the timeout or use the PriorityTask API, but even if I do that, we may run into timeouts due to deadlock. If that happens, I want to know what I can expect the grid to do.
Here's what I'm seeing:
I am running 2 storage-enabled members with backup-count=0. I am running my "client" as a non-storage-enabled member.
First, the client kicks off the EntryProcessor:
Map<Object, Integer> readProcessorResult = requestCache.invokeAll(AlwaysFilter.INSTANCE, processor);
The two members begin logging successful executions of the EntryProcessor. Then, one of the members happens to run it against an entry that takes longer than the service guardian's timeout. We get a soft and hard timeout:
[ERROR] Coherence: 2012-01-26 10:56:20.103/333.297Oracle Coherence GE 3.7.1.2 <Error> (thread=Cluster, member=1): Detected soft timeout) of {WrapperGuardable Guard{Daemon=DistributedCache:jdw-read-request-service} Service=PartitionedCache{Name=jdw-read-request-service, State=(SERVICE_STARTED), LocalStorage=enabled, PartitionCount=257, BackupCount=0, AssignedPartitions=128}}
[WARN ] Coherence: 2012-01-26 10:56:20.121/333.315Oracle Coherence GE 3.7.1.2 <Warning> (thread=Recovery Thread, member=1): Attempting recovery of Guard{Daemon=DistributedCache:jdw-read-request-service}
[ERROR] Coherence: 2012-01-26 10:56:22.604/335.798Oracle Coherence GE 3.7.1.2 <Error> (thread=Cluster, member=1): Detected hard timeout) of {WrapperGuardable Guard{Daemon=DistributedCache:jdw-read-request-service} Service=PartitionedCache{Name=jdw-read-request-service, State=(SERVICE_STARTED), LocalStorage=enabled, PartitionCount=257, BackupCount=0, AssignedPartitions=128}}Now, for some reason (why?), Coherence determines that the service is unrecoverable and it must stop the cluster:
[WARN ] Coherence: 2012-01-26 10:56:22.605/335.799Oracle Coherence GE 3.7.1.2 <Warning> (thread=Termination Thread, member=1): Terminating Guard{Daemon=DistributedCache:jdw-read-request-service}
Coherence <Error>: Halting this cluster node due to unrecoverable service failure
[ERROR] Coherence: 2012-01-26 10:56:23.613/336.807Oracle Coherence GE 3.7.1.2 <Error> (thread=Cluster, member=1): StopRunning ClusterService{Name=Cluster, State=(SERVICE_STARTED, STATE_JOINED), Id=0, Version=3.7.1, OldestMemberId=1} due to unhandled exception:
[ERROR] Coherence: 2012-01-26 10:56:23.613/336.807Oracle Coherence GE 3.7.1.2 <Error> (thread=PacketListener1P, member=1): Stopping cluster due to unhandled exception: com.tangosol.net.messaging.ConnectionException: UdpSocket.receive: unable to reopen socket; State=STATE_CLOSED
at com.tangosol.coherence.component.net.socket.UdpSocket.receive(UdpSocket.CDB:58)
at com.tangosol.coherence.component.net.UdpPacket.receive(UdpPacket.CDB:1)
at com.tangosol.coherence.component.util.daemon.queueProcessor.packetProcessor.PacketListener.onNotify(PacketListener.CDB:20)
at com.tangosol.coherence.component.util.Daemon.run(Daemon.CDB:42)
at java.lang.Thread.run(Unknown Source)
[ERROR] Coherence: 2012-01-26 10:56:23.641/336.835Oracle Coherence GE 3.7.1.2 <Error> (thread=Cluster, member=n/a):
java.lang.NullPointerException: null
at com.tangosol.coherence.component.net.Cluster$ClusterService$TcpRing.onAcceptException(Cluster.CDB:13) ~[coherence-3.7.1.2.jar:3.7.1.2]
at com.tangosol.coherence.component.net.TcpRing.onAccept(TcpRing.CDB:25) ~[coherence-3.7.1.2.jar:3.7.1.2]
at com.tangosol.coherence.component.net.TcpRing.onSelect(TcpRing.CDB:27) ~[coherence-3.7.1.2.jar:3.7.1.2]
at com.tangosol.coherence.component.net.TcpRing.select(TcpRing.CDB:14) ~[coherence-3.7.1.2.jar:3.7.1.2]
at com.tangosol.coherence.component.util.daemon.queueProcessor.service.grid.ClusterService.onWait(ClusterService.CDB:6) ~[coherence-3.7.1.2.jar:3.7.1.2]
at com.tangosol.coherence.component.util.Daemon.run(Daemon.CDB:39) ~[coherence-3.7.1.2.jar:3.7.1.2]
at java.lang.Thread.run(Unknown Source) [na:1.6.0_30]
[WARN ] Coherence: 2012-01-26 10:56:24.976/338.170Oracle Coherence GE 3.7.1.2 <Warning> (thread=Invocation:jdw-invocation-service, member=n/a): failed to stop 95 worker threads; abandoning
Coherence <Error>: Halted the cluster:
Cluster is not running: State=5
Exception in thread "Cluster|SERVICE_STOPPED|Member(Id=1, Timestamp=2012-01-26 10:50:58.044, Address=192.168.1.67:9001, MachineId=52295, Location=site:,machine:DEN12956L,process:10012, Role=CoherenceServer)" java.nio.channels.ClosedSelector
Exception
at sun.nio.ch.SelectorImpl.keys(Unknown Source)
at com.tangosol.coherence.component.net.TcpRing.disconnectAll(TcpRing.CDB:6)
at com.tangosol.coherence.component.util.daemon.queueProcessor.service.grid.ClusterService$TcpRing.onLeft(ClusterService.CDB:4)
at com.tangosol.coherence.component.util.daemon.queueProcessor.service.grid.ClusterService.onStopRunning(ClusterService.CDB:7)
at com.tangosol.coherence.component.util.daemon.queueProcessor.service.grid.ClusterService.onException(ClusterService.CDB:28)
at com.tangosol.coherence.component.net.Cluster$ClusterService.onException(Cluster.CDB:7)
at com.tangosol.coherence.component.util.Daemon.run(Daemon.CDB:85)
[ERROR] Coherence: 2012-01-26 10:56:25.616/338.810 Oracle Coherence GE 3.7.1.2 <Error> (thread=Cluster, member=n/a): StopRunning ClusterService{Name=Cluster, State=(SERVICE_STOPPED, STATE_JOINED), Id=0, Version=3.7.1} due to unhandled exception:
at java.lang.Thread.run(Unknown Source)
[ERROR] Coherence: 2012-01-26 10:56:25.616/338.810Oracle Coherence GE 3.7.1.2 <Error> (thread=Cluster, member=n/a):
java.nio.channels.ClosedSelectorException: null
at sun.nio.ch.SelectorImpl.keys(Unknown Source) ~[na:1.6.0_30]
at com.tangosol.coherence.component.net.TcpRing.close(TcpRing.CDB:11) ~[coherence-3.7.1.2.jar:3.7.1.2]
at com.tangosol.coherence.component.util.daemon.queueProcessor.service.grid.ClusterService.onExit(ClusterService.CDB:1) ~[coherence-3.7.1.2.jar:3.7.1.2]
at com.tangosol.coherence.component.util.Daemon.run(Daemon.CDB:68) ~[coherence-3.7.1.2.jar:3.7.1.2]
at java.lang.Thread.run(Unknown Source) [na:1.6.0_30]Around the same time that member 1 decided to stop its cluster, member 2, which had been happily executing entry processors, begins taking responsibility for member 1's partitions. That's what I'd expect.
[WARN ] Coherence: 2012-01-26 10:56:23.643/336.784Oracle Coherence GE 3.7.1.2 <Warning> (thread=DistributedCache:sys-id-dist-service, member=2): Assigned 128 orphaned primary partitions
[WARN ] Coherence: 2012-01-26 10:56:23.646/336.787Oracle Coherence GE 3.7.1.2 <Warning> thread=DistributedCache:sourceMetadataReviewCache-service, member=2): Assigned 128 orphaned primary partitions
......Member 1 now restarts its cluster and re-joins as member 4, and starts re-starting its services:
[INFO ] Coherence: 2012-01-26 10:56:26.008/339.202Oracle Coherence GE 3.7.1.2 <Info> (thread=main, member=n/a): Restarting cluster
[INFO ] Coherence: 2012-01-26 10:56:26.327/339.521Oracle Coherence GE 3.7.1.2 <Info> (thread=Cluster, member=n/a): This Member(Id=4, Timestamp=2012-01-26 10:56:26.126, Address=192.168.1.67:9001, MachineId=52295, Location=site:,machine:DEN12956L,process:10012, Role=CoherenceServer, Edition=Grid Edition, Mode=Development, CpuCount=2, SocketCount=2) joined cluster "NIR_GRID_DEV" with senior Member(Id=2, Timestamp=2012-01-26 10:51:03.593, Address=192.168.1.67:9003, MachineId=52295, Location=site:,machine:DEN12956L,process:10024, Role=CoherenceServer, Edition=Grid Edition, Mode=Development, CpuCount=2, SocketCount=2)
[INFO ] Coherence: 2012-01-26 10:56:26.364/339.558Oracle Coherence GE 3.7.1.2 <Info> (thread=main, member=n/a): Started cluster Name=NIR_GRID_DEV
Group{Address=224.3.7.0, Port=60000, TTL=0}
MasterMemberSet(
ThisMember=Member(Id=4, Timestamp=2012-01-26 10:56:26.126, Address=192.168.1.67:9001, MachineId=52295, Location=site:,machine:DEN12956L,process:10012, Role=CoherenceServer)
OldestMember=Member(Id=2, Timestamp=2012-01-26 10:51:03.593, Address=192.168.1.67:9003, MachineId=52295, Location=site:,machine:DEN12956L,process:10024, Role=CoherenceServer)
ActualMemberSet=MemberSet(Size=3
Member(Id=2, Timestamp=2012-01-26 10:51:03.593, Address=192.168.1.67:9003, MachineId=52295, Location=site:,machine:DEN12956L,process:10024, Role=CoherenceServer)
Member(Id=3, Timestamp=2012-01-26 10:55:05.522, Address=192.168.1.67:9005, MachineId=52295, Location=site:,machine:DEN12956L,process:13268, Role=IntellijRtExecutionAppMain)
Member(Id=4, Timestamp=2012-01-26 10:56:26.126, Address=192.168.1.67:9001, MachineId=52295, Location=site:,machine:DEN12956L,process:10012, Role=CoherenceServer)
MemberId|ServiceVersion|ServiceJoined|MemberState
2|3.7.1|2012-01-26 10:51:03.593|JOINED,
3|3.7.1|2012-01-26 10:55:05.522|JOINED,
4|3.7.1|2012-01-26 10:56:26.337|JOINED
RecycleMillis=1200000
RecycleSet=MemberSet(Size=0
TcpRing{Connections=[2, 3]}
IpMonitor{AddressListSize=0}
[INFO ] Coherence: 2012-01-26 10:56:26.365/339.559Oracle Coherence GE 3.7.1.2 <Info> (thread=main, member=4): Restarting Service:Management
[INFO ] Coherence: 2012-01-26 10:56:26.417/339.611Oracle Coherence GE 3.7.1.2 <Info> (thread=main, member=4): Restarting Service:jdwSourceManagerCache-service
......While that is happening, member 2 now also encounters a hard timeout on the same service and begins going through the same process that member 1 just went through. I am not sure why member 2 encounters this timeout. Perhaps it is because it ran another entry processor that took too long? It is difficult to tell. Except this time we start having problems when member 2 tries to stop the cluster, and I'm not sure exactly why. Perhaps because member 4 is not yet in a good state?
[ERROR] Coherence: 2012-01-26 10:56:35.282/348.423Oracle Coherence GE 3.7.1.2 <Error> (thread=PacketListener1, member=2): Stopping cluster due to unhandled exception:
com.tangosol.net.messaging.ConnectionException: UdpSocket.receive: unable to reopen socket; State=STATE_CLOSED
at com.tangosol.coherence.component.net.socket.UdpSocket.receive(UdpSocket.CDB:58)
at com.tangosol.coherence.component.net.UdpPacket.receive(UdpPacket.CDB:1)
at com.tangosol.coherence.component.util.daemon.queueProcessor.packetProcessor.PacketListener.onNotify(PacketListener.CDB:20)
at com.tangosol.coherence.component.util.Daemon.run(Daemon.CDB:42)
at java.lang.Thread.run(Unknown Source)
Coherence <Error>: Halted the cluster:
Cluster is not running: State=5
[ERROR] Coherence: 2012-01-26 10:56:42.147/355.288Oracle Coherence GE 3.7.1.2 <Error> (thread=main, member=n/a): Failed to restart services: com.tangosol.net.RequestTimeoutException: Timeout while waiting for cluster to stop.
[ERROR] Coherence: 2012-01-26 10:56:51.324/364.465Oracle Coherence GE 3.7.1.2 <Error> (thread=main, member=n/a): Failed to restart services: com.tangosol.net.RequestTimeoutException: Timeout while waiting for cluster to stop.
...... (error repeats)And the newly re-joined member 4, which had been restarting services and claiming partitions from the newly-dead member 2, appears to restart execution of the entry processor but then complains that its thread was interrupted: I am not sure why this happens or what it means.
[INFO ] Coherence: 2012-01-26 10:56:52.685/365.879Oracle Coherence GE 3.7.1.2 <Info> (thread=DistributedCache:jdw-read-request-service, member=4): Restarting NamedCache: coherence.common.sequencegenerators
[ERROR] Coherence: 2012-01-26 10:56:52.686/365.880Oracle Coherence GE 3.7.1.2 <Error> (thread=DistributedCache:jdw-read-request-service, member=4): This thread was interrupted while waiting for the results of a request:
Poll
PollId=2, active
InitTimeMillis=1327597012685
Service=DistributedCacheForSequenceGenerators (60)
RespondedMemberSet=[]
LeftMemberSet=[]
RemainingMemberSet=[4]
},Meanwhile, my client, who ran the invoke() with the EntryProcessor, has received a message stating "no storage enabled members exist," which although it may be true doesn't seem like it's really the cause of the problem.
Could I be having problems because all my cluster members are executing the same kind of long-running EntryProcessor and all of them are getting service guardian timeouts at around the same time? How do I deal with that? For example, what if a database is running very slowly one day and my entry processors all start to execute slowly? I don't want my whole grid having problems. Should I, for example, limit the number of concurrent EntryProcessors to < count of grid members by using a LimitFilter?
What does it mean that there was a timeout waiting for the cluster to stop?
And what about the client? If I get an exception after running a grid command, is it valid to wait a few seconds for things to stabilize and then try again? What's my best bet as far as that goes?
Thanks! And let me know if I should file a support request instead.rehevkor5 wrote:
I appreciate the responses so far, but unfortunately they give me no new information.
I am aware that I can try to avoid timeouts by using the PriorityTask API and heartbeats, but that still gives me no guarantee that I will not run into a deadlock situation and encounter a timeout. That is fine as long as my grid can deal with it. Currently, it does not behave well when that happens (all members eventually die). I challenge anyone reading this post to try running an entry processor on their grid that is designed to time out (not by using sleep() as that is interruptable via a soft timeout). All your members will probably encounter the timeout at the same time, and it probably will not end well. If, however, you can handle this situation or have some approach that mitigates it, I would love to hear from you!
I am also aware that I can disable the service guardians, or configure them to only log and take no action. However, this leaves me vulnerable to deadlocks.
Therefore, I would still appreciate any responses that address either of these two issues:
1. Configuration changes or other fixes that allow my members to recover successfully from a service timeout
2. Operational best practices that allow my grid to continue running even if an entry processor that is running on every member of the grid times out at the same time. For example, limiting the number of concurrent entry processors.One operational best practice is design your system so you can't get into a deadlock. If it can get into a deadlock once, it can get into it many times. If a system does that, it is not a well-behaving or well-designed system.
If your code can get into a deadlock across the cluster, that usually means that you are trying to do something which you should not have, like trying to operate on multiple resources in an arbitrary order while holding locks on them (e.g. violating the threading guidelines), which is the typical case of a distributed deadlock, and against which you can guard with ordering your multiple locking operations in a consistent order, but you should not expect Coherence to retry and possibly get into the same problem, as all you would achieve with it is that you converted the deadlock into a livelock.
Coherence is not supposed to guard against your errors. With the guardian it gives you a way to find out what your error is, but it should not attempt the impossible by trying to correct it. You should design your system so that it does not have this kinds of errors.
If you think there is a specific reproducible problem in how Coherence reacts to your code which can bring down the system, then create a test case and submit it in a SR. The kinds of exceptions you get make it possible that it may be necessary. If it is indeed Coherence's fault that it dies and not something you did, then I am fairly certain that it will be given quite high priority considering it is an error which can bring a cluster down.
Coherence server-side constructs have an API contract. Single foremost aspect of that is that the operations complete without an error (unless otherwise documented) within a small period of time. If it goes against this then it has to provide feedback or customization with PriorityTask/GuardSupport. A code which can deadlock goes against this contract. After all we are speaking about a grid, not a distributed process manager.
I agree that the grid should not die due to a deadlock, but you should not expect Coherence to fix a deadlock either. But dying due to an exception and having a distributed deadlock is two different and independent issues.
Best regards,
Robert
Edited by: robvarga on Feb 3, 2012 10:12 AM -
Trouble with DAQmxReadDigital Timeout (200284) when used in a threaded loop
Hi,
I'm using a NI6537 for fast Digital Acquisition. The board is installed on a NIPXIe-1062 crate controlled by a NI PXIe-8130 controller, where the software is running. I'm reading all the 32 lines as a single channel, at 50MS/s, and the clock is the one provided by the board itself. I put the timeout as infinite, but I also tried various other settings. As I'm reading a finite samples bunch of 524288 samples, at 50 MS/s, a timeout of 1 second should be by far sufficient.
As far as I put the DAQmxReadDigitalU32(...) call in a simple loop I have no troubles, everything working fine.
for (...) {
DAQmxReadDigitalU32(...);
} // That loop works perfectly
while, if a have a loop inside a multi-thread process, or simply I give the system some freedom inside the loop, sometimes I get the timeout error. Note that the time cost of the Sleep() function is just of some millisecond, so there is no reason for the call to timeout.
for (...) {
DAQmxReadDigitalU32(...);
Sleep(1); // To release system resources...
}// That loop stops erratically
With the last code, I can also see that actually the board did not complete the reading, i.e. is returning less samples than what requested. It seems to me that someting is stopping the acquisition, but I'm not able to figure what. The same happens even in LabView, using the VI read: sometimes the read randomly generates a timeout error and stops, even if LabView is the only running application.
Could you point me what I'm doing wrong?
Thanks, Piero.
DAQmxReadDigitalU32Duplicate Post
ColeR
Field Engineer -
DRM Process Manager failed to start with error Timeout starting the following process: NetJNIBridge.
When we Start the DRM DRM Process Manager failed to start with following error
[Process ID: 3948, Thread ID: 1, Process Manager]
Error loading the NetJNIBridge host process on machine: EU9SC1WNW001
System.Exception: Error loading the NetJNIBridge host process on machine: EU9SC1WNW001 ---> Oracle.Drm.Exceptions.ResourcedException`1[Oracle.Drm.Messages.MsgsProcessManager]: DRM-61028: The following unexpected error occurred communicating with URL 'EU9SC1WNW001': DRM-61023: Timeout starting the following process: NetJNIBridge. DRM Process ID: b3e602fa-f6c1-abcc-4af7-c0a99b51b235
at Oracle.Drm.ProcessManager.Program.ServiceMethod(String machineName, UInt16 port, Action`1 action)
at Oracle.Drm.ProcessManager.Program.StartNonEngineProcesses()
After 11.1.2.3 DRM upgradeOS:linux
i am getting error in installing OPMN manually
when trying to installing OPMN manually getting error i.e,
opmnctl: starting opmn and all managed processes...
opmnctl: opmn start failed
when checked opmn/logs:
opmn.log is empty
ons.log showing error ie:
13/06/17 19:22:45 [4] ONS server initiated
13/06/17 19:22:45 [2] 10.209.178.16:6200 - thread create failed
ipm.log shoeing error i.e:
13/06/18 11:58:04 [4] OPMN server ready. Request handling enabled.
13/06/18 11:58:16 [4] PM state directory exists: /u02/app/orapp/product/10.1.2/opmn/logs/states
13/06/18 11:58:16 [4] PM state file does not exist: /u02/app/orapp/product/10.1. 2/opmn/logs/states/.opmndat
any idea why it is showing error?? -
Sharepoint Farm backup with powershell timeout
Hello experts.
I have faced with the problem using powershell script to manage automatic full farm backups with file rotations.
I use common script taken from this page
http://gallery.technet.microsoft.com/office/9b99c435-8831-4c9e-a70b-1f13158ef22a
And every was fine until backup procedure of wss_content database grew up to 1 hour
I have MS RBS configured for wss_content database and files in BLOB store have about 100Gb in summary
Now i can't build full backup and have error in spbackup.log
[12/4/2012 12:59:21 AM] Progress: [WSS_Content_MP27] 80 percent complete.
[12/4/2012 1:02:03 AM] Warning: [WSS_Content_MP27] Time is out. Server did not respond within the timeout period.
The backup or restore was aborted.
After that script try to repeat failed command 3 times using next statement
SQL command timeout is set to 1.00 hours
Question is how i can increase timeout for this operation?
Because for our database 1 hour is dramatically low value.
One week ago full backup of wss_content database takes 50 minutes.
Thanks.
ruslaninHi,
have you tried to used backupthread parameter like
Backup-SPFarm -Directory C:\Backup -BackupMethod full -BackupThreads 10 -ForceBackupThreads
Specifies the number of threads to be used during the backup. The fewer the threads, the easier the backup log file is to read and understand. The more the threads, the more components that can be backed up in parallet, potentially resulting in a faster backup operation. The minimum value is 1 and the maximum value is 10.
The default value is 3.
If a backup is performed with the –ShowTree parameter, then the BackupMethod parameter is not used.
http://technet.microsoft.com/en-us/library/ff607881.aspxWhere you are backing up ur data local drive or shared drive, also check connectivity and speed incase of shared drive.thx
iffi -
Workflow queues with a timeout for lack of action
I am looking for a way to have a work queue (table) with jobs needing aprovals and after a while of sitting there they need to move to the next level. For example.
I have a ticket system. A new ticket is entered and it must be approved by 5 people. 2 are on a trip. How do I make it skip these people after sitting and waiting for 4 hours.
Currently this was my plan. Create a DB job that runs every 5 minutes and compare the SYSDATE to the ticket age. If it is expired them move the ticket to the approved queue(table)
Any better way for doing this?Hello Tim,
it seems to be a requirement that tickets don't wait for more than 4 hours, so I don't think there is a better way to ensure this.
Possibly you could enhance the process if you could provide a table to track the availability of the approvers: If you can see that two approvers aren't available, you could move the ticket as soon as the third available one approved the ticket, so the ticket wouldn't have to wait for the "timeout".
-Udo -
Problem with VPN timeout on Cisco ASA5505
Hi i'm sorry if it's vague, but i'm coming here without any config simply because i don't have access.
At work we have 1 Cisco ASA5505 which is used for IPSEC VPN only.
We have 4-5 users that work 100% from the VPN (8h per day 40h per week)
The problem we have will be the disconnection.
We have 1 user that will never never never have the problem (he can stay log all 8h if he wants to)
The 2nd user can get disconnected, but mostly if the VPN stays on for too long without any action.
Me and the other user can get frequent Disconnection in a day, but it's all random (1 days i can get disconnected 0 times and the next day 3 times)
I am using Mac OS 10.7 (just like the one that never gets disconnected and the one that gets disconnected randomly)
The other person who gets disconnected alot is on Windows 7 32 bits with Cisco Client.
On my side when i get disconnected there is 2 problem i see (it will happen to the windows person too)
1) When i'm working on servers sometimes i won't be able to click anywhere and i see that my connection is still on, so i need to close it manually wait 2 minutes then reconnect.
2) When i check my VPN connection it simply disconnected alone.
Thanks for possible solutions. (also the windows client had another PC Before and she said it never disconnected, but it started on new PC) (Before she was on WinXP)
ThanksHi i'm sorry if it's vague, but i'm coming here without any config simply because i don't have access.
At work we have 1 Cisco ASA5505 which is used for IPSEC VPN only.
We have 4-5 users that work 100% from the VPN (8h per day 40h per week)
The problem we have will be the disconnection.
We have 1 user that will never never never have the problem (he can stay log all 8h if he wants to)
The 2nd user can get disconnected, but mostly if the VPN stays on for too long without any action.
Me and the other user can get frequent Disconnection in a day, but it's all random (1 days i can get disconnected 0 times and the next day 3 times)
I am using Mac OS 10.7 (just like the one that never gets disconnected and the one that gets disconnected randomly)
The other person who gets disconnected alot is on Windows 7 32 bits with Cisco Client.
On my side when i get disconnected there is 2 problem i see (it will happen to the windows person too)
1) When i'm working on servers sometimes i won't be able to click anywhere and i see that my connection is still on, so i need to close it manually wait 2 minutes then reconnect.
2) When i check my VPN connection it simply disconnected alone.
Thanks for possible solutions. (also the windows client had another PC Before and she said it never disconnected, but it started on new PC) (Before she was on WinXP)
Thanks -
Hello all
I upgraded from Snow Leopard to the latest Mountain Lion OS and now my Wifi will not work. When I try and insert the password to my Wifi network states either 'connection timed out' or 'password and/or user name not recognised' please help...!Take each of the following steps that you haven't already tried, until the problem is resolved.
Step 1
Restart the router. Many problems are solved that way.
Step 2
Change the name of the wireless network, if applicable, to eliminate any characters other than letters and digits. You do that on your router via its web page, if it's not an Apple device, or via AirPort Utility, if it is an Apple device.
Step 3
From the menu bar, select
▹ System Preferences... ▹ Network
Click the Assist me button and select Assistant. Follow the prompts.
Step 4
Back up all data.
Launch the Keychain Access application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Keychain Access in the icon grid.
Enter the name of your wireless network in the search box. You should have one or more "AirPort network password" items with that name. Make a note of the name and password, then delete all the items. Quit Keychain Access. Turn Wi-Fi off and then back on. Reconnect to the network.
Step 5
You may need to change other settings on the router. See the guidelines linked below:
Recommended settings for Wi-Fi routers and access points
Potential sources of interference
Step 6
Make a note of all your settings for Wi-Fi in the Network preference pane, then delete the connection from the connection list and recreate it with the same settings. You do this by clicking the plus-sign icon below the connection list, and selecting Wi-Fi as the interface in the sheet that opens. Select Join other network from the Network Name menu, then select your network. Enter the password when prompted and save it in the keychain.
Maybe you are looking for
-
Female Mini port to VGA adaptor?
Hey Everyone I am looking for female Mini port to VGA adaptor, and i wondered if anyone knew if something like this was made? Thanks for any help or suggestions
-
I need to refinance this auto loan!
One of my auto loans is through Regional Acceptance and it's actually one that I co-signed on but they have me as the primary (of course) and the kid has paid almost $2K and the balance has decreased so far by about $500. (Apparently one of those upf
-
I have down loaded Adobe Re ader X 10.1 and can not get it to work. I can view the PDF report that I need to print but the mouse will not work to chick to print. The screen is frozen. I have chicked the repair the installation three times from the h
-
My G5 Quad (8 gigs ram, plenty of open hard drive space, Sonnet SATA card, two Geforce 6600) has an odd thing going on. When I open any streaming video source, it starts quickly and then within a minute or two the video freezes up while the audio con
-
BB Desktop Manger v5 with 9500 unable to sync Calendar with categories map fields
BB Desktop Manger v5 with BB Storm 9500 Two laptops one with XP sp3 with office/outlook 2003 and the other vista 64bit with office/outlook 2007 The sync of both the Address book and Tasks are great as I can use the catergories "map field" in both of