IfSpeed and ASA security context config

If the "system" context of a multi-context ASA has per-interface config set to a specific speed, say 10Mbit on a 1Gbit interface, I see the interface is reported as 10Mbit in ifSpeed. But does the config only impact the management aspect, or does it throttle the interface down to 10Mbit as well?

What if you do the calculation manually using the delta values polled from SNMP, and the value of ifSpeed? What is the port speed of the upstr
eam switch? Perhaps the port is really negotiated at a higher speed than what the context is reporting.

Similar Messages

Cisco asa security context active/active failover

Hi,
I have two Cisco ASA 5515-X appliance running OS version 8.6. I want to configure these two appliance in multiple context mode mode.
Each ASA appliance will have two security context named "ctx1" & "ctx2".
I have to configure failover on these two ASA appliance such that "ctx1" will be active in one ASA box and "ctx2" will be active and process the traffic on second box to achieve this i will configure two failover group 1 & 2. And assign "ctx1" interfaces in failover group 1 and "ctx2" interface to group 2.
I am a reading a book on failover configuration in active/active in that below note is mentioned.
If an interface is used as the shared interface between multiple contexts, then all of those contexts need to be in the same failover redundancy group.
What this means? can someone please explain because i also want to use a shared interface which will be used by "ctx1" & "ctx2". In this case shared interface can be used in failover group 1 & 2 ?
Regards,
Nick

Yout will have to contact [email protected] or open a TAC case in order to have a new activation key generated. They can do that once they confirm your eligibility.

ASA 5580-20 Security Contexts

Hi,
How many Contexts can a Cisco ASA 5580-20 provide. I have seen that ir is upto 250. Can someone confirm that.
Please do tell me about the licensing part for the same. How many of then come as default with the box and what is the license conditions/specifications for additional contexts. Is it one extra license for every context.
Rgds
Rajesh

Hi Rajesh,
Please refer to this URl Link:-
http://www.cisco.com/c/en/us/td/docs/security/asa/asa82/license/license82.html
Security Contexts
2
Optional licenses:
5
10
20
50
Let me know if this answers your query.
Thanks and Regards,
Vibhor

An impersonation error occurred using the security context of the current user. -- Report server is on remote server and file share folder is on local server

I have deployed a report on the server (e.g. remoteserver\reports) from my local machine. I opened the report in browser in my local machine and created a new subscription with windows file share delivery option.
But its giving an error "Failure writing file \\localserver\subscriptions\Report1.xls : An impersonation error occurred using the security context of the current user." Here "subscriptions"
is the folder which I have created in my local machine.
I followed the instructions found in the link "http://msdn.microsoft.com/en-us/library/ms157386.aspx"
Please help to solve this issue.

Hi,
Thank you for your reply.
I have followed the same process. The credentials which I have given are same as my PC. But I am getting the same error. Can you please clarify the statement "Service
account that is using for file share subscription should have write access to shared folder."
given in the above link?
I am the one who created the folder and subscribing the report, so probably I have the full write permissions to the shared folder. What is the service account in this context?
I think the problem is, I am deploying the report on the server and creating the shared folder in the local machine. I tried giving shared folder permissions to the user on the server. But my local machine is in local domain and I cant access the users on
the remote server. Do I need to create a shared folder on the server? I am new to SSRS. Please help me.
PS: I have assigned with all roles viz. Browser, Content Manager, Publisher, Report Builder etc. and My Role name (WEBSERVER\User)
is different from my local user name (domain\username) in domain.

Prime Infrastructure 2.1 ASA5580- Security Context Partial Collection Failure

I am attempting to add my ASAs into prime but get stuck almost instantly after adding the new device. Prime is able to get the device name and Device type (Cisco ASA-5580 Adaptive Security Appliance Security Context) Admin status shows up as Managed but Inventory Collection Status shows up as "Partial Collection Failure" For more detail it says "feature_image_firewall Unexpected error. See the log file inventory.log for details."
The only failure in inventory.log I could find was
[2014-09-26 12:40:01,868] [ICE Service[ 1]Thread: 20] [inventory] [ERROR] - 192.168.0.19 For device id: 2848866 Feature = feature_image_firewall and Procedure = ImageFireWal failed in time 45 with the following error and continuing with other features: com.cisco.nm.expression.function.FunctionException: <palError><deviceId>2848866</deviceId><code>HANDLER_ERROR</code><message>Error while trying to run handler. Action : imageFireWall, Handler : com.cisco.nm.pal.customhandler.RPLHandler. Error : Exception thrown : Constraint violation. See log for details.</message><handlerCode>ERROR_HANDLER_ERROR</handlerCode></palError>
[2014-09-26 12:40:01,868] [ICE Service[ 1]Thread: 20] [ice] [ERROR] - com.cisco.nm.expression.function.FunctionException: <palError><deviceId>2848866</deviceId><code>HANDLER_ERROR</code><message>Error while trying to run handler. Action : imageFireWall, Handler : com.cisco.nm.pal.customhandler.RPLHandler. Error : Exception thrown : Constraint violation. See log for details.</message><handlerCode>ERROR_HANDLER_ERROR</handlerCode></palError>
com.cisco.nm.expression.function.FunctionException: <palError><deviceId>2848866</deviceId><code>HANDLER_ERROR</code><message>Error while trying to run handler. Action : imageFireWall, Handler : com.cisco.nm.pal.customhandler.RPLHandler. Error : Exception thrown : Constraint violation. See log for details.</message><handlerCode>ERROR_HANDLER_ERROR</handlerCode></palError>
As far as the ASA config goes:
snmp-server enable
snmp-server host management 192.168.10.27 community c!$c0PR!me version 2c
logging enable
logging history 7
snmp-server enable traps
The above config works on our ASA5520s except I still haven't set up the traps right because there isn't any useful information on those devices so I am not sure what I need to change?

My ASA is using DH 1.
For 9.2(1) I read this in the release notes.
Note The ASA 5510, ASA 5520, ASA 5540, ASA 5550, and ASA 5580 are not supported in this release or later. ASA Version 9.1 was the final release for these models.

Dynamic Routing Protocol Support in Cisco ASA Multiple Context Mode

                   Dear Experts,
Wold like to know whether dynamic Routing Protocol Support in Cisco ASA Firewall Multiple Context Mode. If yes then please provide OS version and Hardware Model of Cisco ASA Firewall. Appreciate the quick response. Thanks.

Hi,
Check out this document for the information
http://www.cisco.com/en/US/docs/security/asa/roadmap/asa_new_features.html#wp93116
Its lists the following for software level 9.0(1)
Multiple   Context Mode Features
Dynamic routing in Security   Contexts
EIGRP and OSPFv2 dynamic   routing protocols are now supported in multiple context mode. OSPFv3, RIP, and multicast routing   are not supported.
Seems to me you would need some 9.x version to support the above mentioned Dynamic Routing Protocols.
I don't think its related to the hardware model of the ASA other than that it requires a model that supports Multiple Context Mode. To my understanding the only model that doesnt support that is ASA5505 of the whole ASA5500 and ASA5500-X series.
Hope this helps
- Jouni

Security context issue when executing a SQL command in SQLCMD

Simplified core issue below:
I have myscript.sql that has:
SELECT name FROM Sys.Databases
GO
USE mydatabase
GO
EXEC mystoredprocedure 'myparameter'
GO
When I open cmd.exe and use:
SQLCMD -S localhost\myinstance -i script.sql
It executes fine.
When I open cmd.exe in C# using the Process class and execute the same command I get the following error:
name
master
tempdb
model
msdb
mydatabase
(5 rows affected)
Msg 916, Level 14, State 1, Server localhost\myinstance, Line 1
The server principal "NT AUTHORITY\SYSTEM" is not able to access the database "mydatabase" under the current security context.
Msg 2812, Level 16, State 62, Server localhost\myinstance, Line 1
Could not find stored procedure 'mystoredprocedure'.
And now the detailed explaination:
I created an MSI which installs my custom application.
During the bootstrap process, SQL Server 2012 Express is installed using the following parameters:
/INSTANCEID="SQLEXPRESS"
/ACTION="Install"
/FEATURES=SQLEngine,Replication
/HELP="False"
/INDICATEPROGRESS="False"
/Q="True"
/QS="False"
/ROLE="AllFeatures_WithDefaults"
/ENU="True"
/ERRORREPORTING="False"
/SQMREPORTING=0
/INSTANCENAME="SQLEXPRESS"
/AGTSVCACCOUNT="NT AUTHORITY\NETWORK SERVICE"
/AGTSVCSTARTUPTYPE="Disabled"
/ISSVCSTARTUPTYPE="Automatic"
/ISSVCACCOUNT="NT AUTHORITY\NetworkService"
/ASSVCSTARTUPTYPE="Automatic"
/ASCOLLATION="Latin1_General_CI_AS"
/ASDATADIR="Data"
/ASBACKUPDIR="Backup"
/ASTEMPDIR="Temp"
/ASCONFIGDIR="Config"
/ASPROVIDERMSOLAP="1"
/SQLSVCSTARTUPTYPE="Automatic"
/FILESTREAMLEVEL="0"
/ENABLERANU="True"
/SQLCOLLATION="SQL_Latin1_General_CP1_CI_AS"
/SQLSVCACCOUNT="NT Authority\Network Service"
/SECURITYMODE="SQL"
/ADDCURRENTUSERASSQLADMIN="True"
/RSSVCACCOUNT="NT AUTHORITY\NETWORK SERVICE"
/RSSVCSTARTUPTYPE="Automatic"
/RSINSTALLMODE="FilesOnlyMode"
/HIDECONSOLE
/IACCEPTSQLSERVERLICENSETERMS
/SAPWD="***************"
The MSI then executes an Installer class DLL written in C# which restores a database to the SqlExpress instance.
When the restore is completed, the Installer class then uses the Process class to launch CMD.exe and execute the SQL script using SQLCMD.
Process vProcess = new Process();
ProcessStartInfo vStartInfo = new ProcessStartInfo("cmd.exe");
vStartInfo.Arguments = "/c set path=%path%;" + Context.Parameters["TargetDir"] + "\\; && sqlcmd -S LocalHost\\myinstance -i myscript.sql";
vProcess.StartInfo = vStartInfo;
vProcess.Start();
vProcess.WaitForExit(30000);
This is where I get the error mentioned above.
However if I execute the same command manually by opening CMD.exe from the RUN command, it executes perfectly.
I can not use -U or -P to supply a user / password, I MUST use integrated security.
Additional info:
Previously SQL Server 2008 Express has been in use for the bootstrapper, and this issue did not occur.
The database the MSI restores is also built from SQL Server 2008. (Will be built from 2012 in the future.)
Installation is performed on an account with administrative rights.
Running the installer AS Administrator does not fix the issue.
Any help would be greatly appreciated, as well please let me know if additional info is required.
Thank you

I'm having a similar issue where I'm using a batch file to execute commands to a group of servers. I can use the batch commands when updating MyDatabase but get the security context error when I try to update MyDatabase with a join to TheirDatabase except
on servers where I am sysadmin. Like I said, I can update MyDatabase as long as I don't join to TheirDatabase.
Update A
Set A.CCMCoderStaffSID = IsNull(B.StaffSID, -1)
From MyDatabase.[R_Encounter].[VejdPfcsLinkageDataF19610x5] A
Left Join ThierDatabase.Staff.Staff B on
A.Sta3n = B.Sta3n and A.[CCMCoderF200IEN]= B.StaffIEN
Error:
Msg 916, Level 14, State 1, Server R04PHIDWH58, Line 1
The server principal "MyDomain\ME" is not able to access the database "TheirDatabase" under the current security context.
Line from batch:
sqlcmd -S Server54 -d MyDatabase -i D:\ETLDevelopment\R04\Me\querytools\%RAWTablesScript% -o D:\ETLDevelopment\R04\Me\UpdateSIDV1.txt

Licensing -Security Contexts on ASA5585-X

All,
I have a customer with 2 ASA 5585-X and they are looking at running a total of 20 Security contexts in failover mode on these two firewalls. From a licensing perspective, Can I get 10 security contexts on each of these firewalls and that gives me a cumulative context number of 20.I am not sure though if I will be able to run all 20 contexts in failover mode on both firewalls.
This is the document I am reading but not very clear.
http://www.cisco.com/en/US/docs/security/asa/asa90/license/license_management/license.html#wp1345944
Thanks

Hi,
If you want to split the 20 Security Contexts between 2 differents ASAs then you are looking at configuring a Active/Active Failover environment.
If you want all Security Contexts to be Active only on one physical ASA at a time (while the other is there to take over when the main one fails) then you are looking at configuring a Active/Standby Failover enviroment.
So in other words
Each units 10 Security Context license will be combined between the units
You can either use 20 Security Contexs on a single physical unit at a time in Active/Standby
OR you can divide the 20 Security Contexts between the 2 Physical ASAs in Active/ActiveFor example 10 Active in ASA1 and 10 Active in ASA2
Also heres a partial quote from the Cisco document
Failover License Requirements and Exceptions
Failover units do not require the same license on each unit.
Older versions of ASA software required that the licenses match on each unit. Starting with Version 8.3(1), you no longer need to install identical licenses. Typically, you buy a license only for the primary unit; for Active/Standby failover, the secondary unit inherits the primary license when it becomes active. If you have licenses on both units, they combine into a single running failover cluster license. How Failover or ASA Cluster Licenses Combine
For failover pairs or ASA clusters, the licenses on each unit are combined into a single running cluster license. If you buy separate licenses for each unit, then the combined license uses the following rules: For example, for failover: You have two ASA 5540 ASAs, one with 20 contexts and the other with 10 contexts; the combined license allows 30 contexts. For Active/Active failover, the contexts are divided between the two units. One unit can use 18 contexts and the other unit can use 12 contexts, for example, for a total of 30.
- Jouni

Cisco Prime Infrastructure 2.0 and ASA 55xx platform

Hello,
We recently upgraded to Prime Infrastructure 2.0 with the hope being able to manage our ASA's from PRIME (and complete an LMS migration).
When I attempt to add ASA's to prime i get the following collection errors:
Unable to collect processor and RAM information.          Processor and RAM information.          Unexpected error. See the log file inventory.log for details.
In the logfile I get the following XML parsing error on the MIB:
<palError>
<deviceId>6284310032</deviceId>
<code>VALIDATION_ERROR</code>
<message>Failed to validate output XML: cvc-maxInclusive-valid: Value '3484331296' is not facet-valid with respect to maxInclusive '2147483647' for type 'int'.</message>
<result>
    <result xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:noNamespaceSchemaLocation="/CISCO-MEMORY-POOL-MIB/xmp-im-file-system-module.xsd">
      <xmp-im-file-system-module>
        <MemoryPoolStatistics>
          <memoryPoolIndex>1</memoryPoolIndex>
          <free>4294967295</free>
          <largestFree>4294967295</largestFree>
          <used>3484331296</used>
        </MemoryPoolStatistics>
To me it seems that the ASA returns a value that is bigger then int32 and thus causes an overflow? Any clues? Workarounds to add an ASA to Prime without checking these MIB'S?
Regards,
Marcel

The X series (all with 64-bit SMP images) are not currently supported by PI 2.0. We can hope for a device update in the coming months to remedy that situation.
If you click on the arrow next to the help icon in the top right of your PI and choose "Device Level Support" you will see:
Cisco ASA-5500 Series Adaptive Security Appliances
Features :
Topology
LLDP Neighbor Discovery
CDP Neighbor Discovery
Configuration
Configuration Archive
Software Image Management
Monitoring
Device Availability
Reachability
Inventory
Physical
System - Memory Pools
Interfaces - IP
Interfaces - Ethernet
Device Type
SYSOIDS
S/W Version
Software
Cisco ASA-5510 Adaptive Security Appliance
OID:1.3.6.1.4.1.9.1.669
OID:1.3.6.1.4.1.9.12.3.1.3.447
Cisco ASA-5510 Adaptive Security Appliance Security Context
OID:1.3.6.1.4.1.9.1.773
Cisco ASA-5520 Adaptive Security Appliance
OID:1.3.6.1.4.1.9.1.670
OID:1.3.6.1.4.1.9.12.3.1.3.448
Cisco ASA-5520 Adaptive Security Appliance Security Context
OID:1.3.6.1.4.1.9.1.671
Cisco ASA-5540 Adaptive Security Appliance
OID:1.3.6.1.4.1.9.1.672
OID:1.3.6.1.4.1.9.12.3.1.3.449
Cisco ASA-5540 Adaptive Security Appliance Security Context
OID:1.3.6.1.4.1.9.1.673
Cisco ASA-5560 Adaptive Security Appliance
OID:1.3.6.1.4.1.9.12.3.1.3.454
Cisco ASA-5550 Adaptive Security Appliance
OID:1.3.6.1.4.1.9.1.753
Cisco ASA-5550 Adaptive Security Appliance Security Context
OID:1.3.6.1.4.1.9.1.763
Cisco ASA-5505 Adaptive Security Appliance
OID:1.3.6.1.4.1.9.1.745
OID:1.3.6.1.4.1.9.12.3.1.3.560
Cisco ASA-5580 Adaptive Security Appliance
OID:1.3.6.1.4.1.9.1.914
Cisco ASA-5585 Adaptive Security Appliance
OID:1.3.6.1.4.1.9.1.1194
OID:1.3.6.1.4.1.9.1.1195
OID:1.3.6.1.4.1.9.1.1196
OID:1.3.6.1.4.1.9.1.1197
Cisco ASA-5585 Adaptive Security Appliance Security Context
OID:1.3.6.1.4.1.9.1.1198
OID:1.3.6.1.4.1.9.1.1199
OID:1.3.6.1.4.1.9.1.1200
OID:1.3.6.1.4.1.9.1.1201
Cisco ASA-5585 Adaptive Security Appliance System Context
OID:1.3.6.1.4.1.9.1.1202
OID:1.3.6.1.4.1.9.1.1203
OID:1.3.6.1.4.1.9.1.1204
OID:1.3.6.1.4.1.9.1.1205
Cisco ASA-5580 Adaptive Security Appliance Security Context
OID:1.3.6.1.4.1.9.1.915
Cisco ASA-5580 Adaptive Security Appliance System Context
OID:1.3.6.1.4.1.9.1.916

Cascading Security Contexts

Hi..
Anybody knows how to configure Cascading Security Contexts in Cisco ASA? How works?
Any step by step configure?
Thanks...

Hello Luis,
That document is rather sparse when it comes to detailed information on Cascading contexts. Are there any documents that go into more details?
In particular I am looking for packet processing information. If you have multiple contexts that have their outside interfaces connected to a "Gateway Context" is Inter-Context traffic processed entirely by the ASASM and does not hit the switch?
Im comparing this to a standard configuration in which multiple contexts would have their Outside interfaces connected to the switches MSFC. In that configuration I would think that the switch would need to process the packets as they egress the outside interface of one context and ingress the outside interface of another.
I would see how in either scenario the switch would process the Layer-2 switching. In the 1st example I would not expect the switch to have to process the Layer-3 traffic as its routing between 3 different contexts on the same ASASM and not having to route down to the MSFC.
Thank you.
Edit:
Just thought of something else I had on my mind. Would it be possible to run EIGRP between cascading contexts when running ASA Version 9.0(1)

VPN with Cisco 877 and ASA 5505

Hi Experts
this is my scenario :
remote clients ----> Internet----> Cisco 877---> ASA5505---->LAN
i would like to allow remote users to connect to my LAN to chek their mails and work as they are in the office. Actually i have configured Cisco877 as VPN Server this is working Fine. but now i'm trying to use ASA with the router because it permit 25 connections at the same time.
i'm connected to internet using a public ISDN IP.i have heard that i need a second IP adresse for ASA ! and the ASA must act as VPN server and the router as Client, is that right ?
if i need to configure the link between the router and ASA how can i do it ? i can't find any document or example in the net :/
please i need your support to make this dream real lol.
i will poste my configuration step by step following your help.
many thanks.

ASA need public ip address that is sure and also ASA acts as vpn. Client server will be remote not router. For that you can use any Ethernet. Trying to make a remote VPN connection via the cisco client, authenticate against an RSA Secure Token server and provide the client an IP address via DHCP.

How to share security context between different application ?

Hi all,
I have two applications(ADF faces + BC, JDev 10.1.3.1) deployed into OAS 10.1.3.1.
The two applications are :
1) SalesApp -> main menu page = SalesMenu.jspx
2) ReportApp -> main menu page = ReportMenu.jspx
I want implement security using CustomLogin.
The question is :
How can I share security context between the applications ?
What I mean is, from SalesMenu.jspx there is one menu item to jump into ReportMenu.jspx, and I want user no need to Login again, Login is once and the user is recognized in the two apps. How to achieve that ?
Thank you for your help,
xtanto

Xtanto,
actually you can't if these are separate J2EE application deployments. The session is not shared and thus the authentication is lost. I heard that OracleAs is planning to implement a feature that allows you to share the session and thus a context between two J2EE deployments. I am not 100 % sure this is the case and will check with OC4J Product Management
Frank

How to get security context in BPEL to get Logged in UserId

Hi All,
We have a requirement of getting security context in BPEL flow and from that we want to extract currentUserId. The requirement is to know who has initiated the composite flow. We are not passing userId in the event payload. In ADF we get the same through following expression:
ADFContext.getCurrent().getSecurityContext().getUserName()
Is there any similar api which we can access to get currentUserId?
Thanks,
Naga

Hi,
If your BPEL has oracle/wss_username_token_service_policy you can retrieve the username from the SOAP headers...
Have a look at this...
http://yuanmengblog.blogspot.com.au/2012/09/extracting-and-passing-wss-name-token.html
Cheers,
Vlad

The server principal "XYuser" is not able to access the database "Ydb" under the current security context

SQL2005 on winserver 2003. I have a view in Xdb that accesses tables in 2 different databases (Xdb and Ydb) on the same server. I have mixed mode security. I have a SQL user (XYuser) that has read access to all tables and views on both databases, yet when I try to access the view using a C# windows application I get the following error:
The server principal "XYuser" is not able to access the database "Ydb" under the current security context
This same scenario works under SQL 2000. I looked through the postings and tried to set TRUSTWORTHY ON on both databases but that didn't help. I can access any other views or tables on the SQL 2005 server, just not the one that joins the tables cross databases. Any help is much appreciated... john

This appears to be a Login/Database Mapping issue. I was having this problem, but was able to resolve it as follows:
Using the SQL Server management Studio:
In the Object explorer, under the SERVER security folder (not the database security folder), expand Logins.
That is: ServerName -> Security -> Logins
NOT: ServerName -> Databases -> DatabaseName -> Security -> Users
Select the Login that is having the troubles. Right click on the Login and select ‘Properties.’
The ‘User Mapping’ page should list all databases on the server with a check mark on the databases that the Login has been mapped to. When I was getting the error, the database in question was not checked (even though the Login was assigned as a User on the database itself). Map the Login by checking the box next to the database name. Set the default schema. Then select the roles for the Login in the Database role membership list box. I selected db_datareader and public. After clicking OK to save the changes, the problem was resolved.
In order to ‘Map’ the Login, the Login must not already be as User on the database, so you may have to go to the database security (ServerName -> Databases -> DatabaseName -> Security -> Users) and delete the Login from the list of database Users before mapping the Login to the database.

HTTP (Axis) Receiver Adapter error: The security context token is expired or is not valid

Hi Experts,
We are required to send a message through PI 7.31 (single stack) in a Soap-to-Soap scenario connecting to a Soap 1.2 Web Service.
We are getting a Security Context Token expired or Invalid error.
Please help us resolving this error.
Thanks in advance!
The Channel Configurations are as follows:
Processing sequence:
Module configurations:
1.
2.
3.
4.
Best Regards
Vikram

Hi all !
First of all, thanks for your answers..
Stefan Grube:
Itu2019s not a Adapter Module.
The module tab following configuration
Processing Sequence:
AF_Adapters/axis/AFAdapterBean     Local Enterprise Bean     afreq
AF_Adapters/axis/HandlerBean                     Local Enterprise Bean     xireq
AF_Adapters/axis/HandlerBean                     Local Enterprise Bean     trp
AF_Adapters/axis/HandlerBean                     Local Enterprise Bean     dcres
AF_Adapters/axis/HandlerBean                     Local Enterprise Bean     xires
AF_Adapters/axis/AFAdapterBean     Local Enterprise Bean     afres
Module Configuration
xireq          handler.type     java:com.sap.aii.axis.xi.XI30OutboundHandler
trp          handler.type     java:com.sap.aii.adapter.axis.ra.transport.http.HTTPSender
trp          module.pivot     true
xires          handler.type     java:com.sap.aii.axis.xi.XI30OutboundHandler
How can i know if those values are correct ?
Srinivas Reddy:
Thanks for the documentation
I have applied SAP Note 11016021 and the error changed, now it says:
Axis: fatal error in invocation: java.lang.NoSuchMethodError: com/sap/aii/axis/xi/XIUtils.setOperation(Ljava/lang/String;Lorg/apache/axis/MessageContext;)V
Message processing failed. Cause: com.sap.engine.services.ejb.exceptions.BaseTransactionRolledbackLocalException: Exception thrown in method process. The transaction is marked for rollback.
Edited by: Antonio Guzman on Jul 9, 2008 5:29 PM

IfSpeed and ASA security context config

Similar Messages

Maybe you are looking for