Ignoring TCP handshake & Sequence Numbers for STT Traffic

Hi,
I have to pass STT traffic through a Cisco ASA (details on STT are here http://tools.ietf.org/html/draft-davie-stt).
STT traffic looks like TCP traffic (i.e. it uses IP protocol 6 and is sent to a specific destination port) but is stateless. It doesn't perform TCP handshake, i.e. TCP flags are used differently same goes for sequence numbers.
Is there any way to disable to regular TCP handshake and sequence numbers checks? I saw that there might be a chance to do something for the handshake with the embryotic connection limit but I'm not sure about the sequence numbers.
Assume ASA 8.6.
Thanks,
Ben

Hi,
You can configure tcp state bypass only for this traffic, for the rest the firewall would check the tcp state of the packet, here is the doc:
http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a0080b2d922.shtml
Hope that helps.
Thanks,
Varun Rao
Security Team,
Cisco TAC

Similar Messages

Documents Sequence numbering for each Branch (Branch as segment)

dear Brother's
can help me in this case
Documents Sequence numbering for each Branch (Branch as segment)
Each branch have an own sequence
I implement oracle Business suite ERP for Five Branch ( KSA,INDIA,DUBIA ,JORDAN ,SYRIA )
I want to segregate sequence numbering for each branch, sequence for (
Sales order, invoice, purchase order, Invoice)
Is there a possibility to link sequence with any segment I define it in COA like Branch
Note: I work in single Operating Unit

Hi,
You might be able to adapt this solution to work for your case: https://acrobat.com/#d=*2slxPLc6c-H0U449vA4jQ. It's more about page numbers for different Master Pages, but you may be able to tie it to the different data nodes.
Niall

Separate automatic document sequence numbering for diff. branches

Hi,
The client wants to have different automatic document sequence numbering for its various branches.preferably the sequence will start from a prefix depicting a branch and sequential vouchers will be generated. in this way all the branches will have their vouchers in sequence. tracking and filling will become easier.
if sombody knows the way of doing it, please respond.
null

Hi
By using Document sequencing, you can do this have separate document sequence numbers for each bank, each branch with a code.
Please contact for further details.
Thanks
bharat

How to enable automatic sequence numbering for intercompnay invoice?

How can the sequence for "PA Internal Invoice" be automated.?

Hi
You may navigate to Projects Implementation Options, and go to the tab - Internal Billing.
There you may find the field - Invoice Numbering. You can select Automatic or Manual.
Per your requirement enter - Automatic, and go on entering the starting number to use for internal invoices.
Dina

Websheets - sequence numbers for new rows

Hi,
I am creating a websheet application to use for a tasks/bug tracker for a project.
I would really like the first column to be of a number format that is automatically filled with the next number in a sequence.
This is quite necessary to have as there will be many rows, and during meetings it will be much easier to refer to a bug or task by it's unique number!
I cant seem to find any info on forums or blogs. And maybe it's because I haven't had my coffee yet, but I can't seem to figure out a way to embed some SQL and a trigger.
Anyone have any tips? Or a reason why this isn't an available functionality in the column properties?
APEX version: 4.2.0.00.27
Regards,
Amanda

What's your Oracle version ?
Here an example with MERGE statement :
merge into test b
using(select rowid rwd,
             dense_rank() over (order by your_sorted_column) dr
      from   test)e
on (b.rowid = e.rwd)
when matched then update set b.seq = dr;On 10g, you can avoid the INSERT clause, since you're sure all the rows will be joined.
On older database, you can insert all null.
Or update statement :
update test b
set    b.seq = (select dr
                from   (select rowid rwd,
                               dense_rank() over (order by your_sorted_column) dr
                        from   test) e
                where r.rowid=e.rwd);Nicolas.

Enhancement Request: Recalculate Sequence Numbers

Hi
Wherever apex has sequence numbers (for branchs, items, regions etc.), please could we have the ability to recalculate them based on increments of ten so for example items as follows:
P_ITEM1 - sequence = 1
P_ITEM1 - sequence = 11
P_ITEM1 - sequence = 12
P_ITEM1 - sequence = 100
P_ITEM1 - sequence = 120
Would become:
P_ITEM1 - sequence = 10
P_ITEM1 - sequence = 20
P_ITEM1 - sequence = 30
P_ITEM1 - sequence = 40
P_ITEM1 - sequence = 50
The option to exclude items with a sequence number of 999 from the recalculation would also be handy. This can become a bit of a pain when a page has been updated many times and you end up with bunching of sequence number so that if something has to be inserted between them, you have to edit a number of items or whatever to make that happen.
If you could do a page-wide or application-wide recalculation - t'would also be cool.
If this feature is available already, please point me to it.
Cheers
Ben

The Cleanup feature Paul mentioned is new in 4.0 but fyi in any version component sequence numbers accept non-integer values so you can always insert something anywhere without a need to resequence...Thanks! I never knew that! Oh yes. And they can be negative too. We have some very esoteric looking sequences...
Actually the decimals are pretty useful for things like conditional display of regions. If you've got 3 related but mutually exclusive regions, numbering them 20.1, 20.2, and 20.3 indicates the relationship between them. Which brings me to another enhancement request: regions to have separate name and title properties (like pages do), so that where such regions have to have the same title shown to users, it's a lot easier for developers to tell them apart.

Recycled Sequence Numbers

Hi,
We have a requirement of generating sequence numbers for a table and we need to recycle them if some of them is deleted.
For example the following tabe Employee(Id,name)
ID NAME
1 XXX
2 YYY
3 ZZZ
4 AAA
The ID filed should have the next sequence number generated. When I call getnextID now, it should return 5
ID NAME
1 XXX
2 YYY
3 ZZZ
4 AAA
5 BBB
Now Let us assume I delete 3. The contents of the table aare
ID NAME
1 XXX
2 YYY
4 AAA
5 BBB
Now when getNextID, 3 should be returned.
How to achieve this in a best performing way in Oracle? Are there any patterns around it? Please note this should run in a multi user environment.
Thanks,
Rama

I think the answers were based on the fact that you call it incorrectly sequence.
Your ConnectivityID is more as a resource that could be recycled. I see some similarities to the GSM telecom market where a resource(i.e. a phone number or a SIM card no) can be recycled when is not active anymore (under certain conditions however).
Personally I would generate a table of resources having the resource number (ConnectivityID) and resource status.
To simplify it, suppose that you have column status with 2 possible values, 0=available, 1=not available.
When you want to allocate the resource number(ConnectivityId) you will set the status to 1.
When the record is deleted then status will be updated back to 0.
Recycling a ConnectivityID will mean searching in the table for the lowest number having status=0.
Of course you don't expect this to be as fast as a sequence but I think this is a different requirement, IMO.
Regards
Al

Temporary sequence numbers

Hello all,
Is there any provision in the mobile server and mobile client to synchronize the Lite database by using temporary sequence numbers for the newly added records?
In the application that we are involved with, we are being asked to provide this behavior.
In details we would ensure that the sequence generation works as it works for the desktop PCs as well.
As far as we know we should follow the following steps for the synchronization:
1. sync new rows with the server
1a. the server syncs with the database, replaces temporary seqnos with the ones that come from the database
2. sync the new seqnos back to the mobile device...
Please let me know whether it is possible or not with the Oracle Lite system,
Thanks in advance,
Balazs

do you have some need to keep the range of DONOR_ID sequential?
In our implementation we use the other method that Greg has mentioned, defining sequences within the oracle lite publication itself
We use sequence generated ID values as the primary key on a lot of our tables, and the columns are defined as NUMBER(12) (reasons are historical, and not necessarly for any good reason - but stuck with it)
looking at the worst case scenario (to keep things simple) in the server we have table PLOTS. The highest ID value is around 5.5 million, with an annual growth rate of 500,000 for server created records. The number of records that would be created on any particular client on an annual basis is more like 2,000.
When you define a sequence within the mobile server you specify a 'template' for each sequence consisting of
name (eg: PLO_ID_SEQ)
start value
increment
window (number of values to assign to a particular user)
threshold (point at which the next set of values is sent to the user)
for PLO_ID_SEQ, the start value is set at 500 million (overkill, but server generated id values will never reach this point in practice), increment is 1, window = 100,000 and threshold is 95,000
This in practical terms means that the sequences on the clients will never need to be re-sent as the values will never reach the threshold, and there will never be any cross over with server generated sequences
When you add your first client to the application, the actual sequence start value will be set for that client as 500,000,000. for the second user added it will be 500,100,000, for the third 500,200,000 etc.
On the whole the mobile server manages this ok, but we have found that if there is a need to replace a client by rebuilding the database from scratch, occasionally it does not correctly maintain the last value used. To get around this we reset the user prior to the rebuild (this resets the sequence start for that user to the next range of values)
This works ok, and is straightforward to implement as you need no code change/data manipulation on the server, but does result in the source of the records being obviously different (can be useful), and you cannot assume that the highest id value is the most recent record (can be a problem for reports)

Invoice Sequence Numbers

Version : Oracle Apps 11.5.1 OS : HP-UX 64 bit.
Module : Order Management.
I want to generate unique sequence numbers for my shipment documents. For example, I have 2 customers A and B. I want my invoice numbers as A-001 for first customer, and A-002 for second customer and so on.
How to generate such a sequence (alphanumeric). Any suggestions?
TIA.

Version : Oracle Apps 11.5.1 OS : HP-UX 64 bit.
Module : Order Management.
I want to generate unique sequence numbers for my shipment documents. For example, I have 2 customers A and B. I want my invoice numbers as A-001 for first customer, and A-002 for second customer and so on.
How to generate such a sequence (alphanumeric). Any suggestions?
TIA.

ACE Normalization for SMTP Traffic

Hi,
I was facing issue with the ACE normalization and that was stopping my SMTP traffic. When i disabled it globally my SMTP traffic is working fine. But due to the audit i cannot disabled it for all the traffic. I want to disabled the normalization only for the SMTP por 25 traffic.
I am trying to create the L4 policy as mention below but unable to set the partameter require for to disable the normalization.
class-map match-any SMTP_CLASS
match port tcp eq 25
parameter-map type connection TCP_SMTP_MAP
no random-sequence-number
exceed-mss allow
policy-map multi-match TCP_SMTP_POLICY
What else i need to reacll in parameter-map in order to disable the normalization for SMTP traffic.
Pleae help.

Hi,
I have attached the capture when normalization was enabled (not working) and capture when normalization was disabled.
Please review and let me know how to achive this by fine tunning the parameters.
We are seeing lot of tcp retransmission error etc.
I have done some research and normalization deals with the following below mentoin parameters.
exceed-mss-----Configure behavior if a packet exceeds MSS
random-seq-num-disable----Disable TCP sequence number randomization
reserved-bits-----Configure Reserved bits in TCP header
syn-data-----Configure behavior for a SYN packet containing data
tcp-options-----Configure TCP header options
urgent-flag-----Allow/Clear Urgent flag

AutoQoS for voice traffic settings?

Hi Everybody,
I have enabled auto qos on switch and following are information
Voice is the most important traffic in network, must ensure voice traffic goes first
SW# show mls qos map dscp-output-q
Dscp-outputq-threshold map:
d1 :d2 0 1 2 3 4 5 6 7 8 9
0 : 04-03 04-03 04-03 04-03 04-03 04-03 04-03 04-03 04-01 04-02
1 : 04-02 04-02 04-02 04-02 04-02 04-02 03-03 03-03 03-03 03-03
2 : 03-03 03-03 03-03 03-03 02-03 02-03 02-03 02-03 02-03 02-03
3 : 02-03 02-03 03-03 03-03 03-03 03-03 03-03 03-03 03-03 03-03
4 : 01-03 01-03 01-03 01-03 01-03 01-03 01-03 01-03 02-03 02-03
5 : 02-03 02-03 02-03 02-03 02-03 02-03 02-03 02-03 02-03 02-03
6 : 02-03 02-03 02-03 02-03
SW# show mls qos queue-set
Queueset: 1
Queue : 1 2 3 4
buffers : 10 10 26 54
threshold1: 138 138 36 20
threshold2: 138 138 77 50
reserved : 92 92 100 67
maximum : 138 400 318 400
For the
DSCP 46 : it's 01-03 (voice)
DSCP 0 : it's 04-03 (general traffic)
From my understanding
- 01-03 means queue 1 and threshold3. (by default threshold3 is 100 and hidden)
- queue-set 1 is enabled by default on all interface and hidden
According to the above information,
- Does the Auto Qos is design for voice goes first?
- Why the Q1 buffer and maximum are less then Q4? isn't suppose to set more buffer on Q1 for voice traffic? or I have to re-distribute the queue buffer and threshold, etc...
- or I just use priority-queue out, then those queue setting will be ignored?
Thanks in advance
Sam

udp ports 16384 to 32767 for rtp traffic
1720 tcp for control (h323 protocol)

Finding missed sequence numbers and rows from a fact table

Finding missed sequence numbers and rows from a fact table
Hi
I am working on an OLAP date cube with the following schema:
As you can see there is a fact transaction with two dimensions called cardNumber and Sequence. Card dimension contains about three million card numbers.
Sequence dimension contains a sequence number from 0 to 255. Fact transaction contains about 400 million transactions of those cards.
Each transaction has a sequence number in 0 to 255 ranges. If sequence number of transactions of a card reaches to 255 the next transaction would get 0 as a sequence number.
For example if a card has 1000 transactions then sequence numbers are as follows;
Transaction 1 to transaction 256 with sequences from 0 to 255
Transaction 257 to transaction 512 with sequences from 0 to 255
Transaction 513 to transaction 768 with sequences from 0 to 255
Transaction 769 to transaction 1000 with sequences from 0 to 231
The problem is that:
Sometimes there are several missed transactions. For example instead of sequence from 0 to 255, sequences are from 0 to 150 and then from 160 to 255. Here 10 transactions have been missed.
How can I find all missed transactions of all cards with a MDX QUERY?
I really appreciate for helps

Thank you Liao
I need to find missed numbers, In this scenario I want the query to tell the missed numbers are: 151,152,153,154,155,156,157,158,159
Relative transactions are also missed, so I think it is impossible to get them by your MDX query
Suppose this:
date
time
sequence
20140701
23:22:00
149
20140701
23:44:00
150
20140702
8:30:00
160
20140702
9:30:00
161
20140702
11:30:00
162
20140702
11:45:00
163
As you can see the sequence number of the last transaction at the 20140701 is 150
We expecting that the first transaction of the next day should be 151 but it is 160. Those 10 transactions are totally missed and we just need to
find missed sequence numbers

DI-Error: You cannot select batch or serial numbers for a closed row

Hello Experts,
I have several B1-Systems connected to R/3-Systems via B1iSN.
In B1 for example I have 2 rows in Purchase Order. One row was closed by a goods receipt - 1 row is still open.
From our R/3-System we send Order-Acknowledgements to B1. Because line 1 is already closed we want to ignore row 1 and update only information in row 2. By using KeyExpansion I could solve that requirement (check in B1-System if row is already closed -> insert row in IDoc only with LineNum). For example:
<Document_Lines>
*<row>* 
    *<LineNum>0</LineNum>*
*</row>*
   <row> 
    <LineNum>1</LineNum>
    <ItemCode>ABCDEFGHIJK</ItemCode>
</row>
</Document_Lines>
Unfortunately DI-API does not allow to update each row separated. I always have to send all rows in IDoc even if one row is closed.
For one B1-Company batchnumbers on every transaction is required. When creating Goods Receipt we have to define a batchnumber for item. But now if I want to update a open row (as described above) I get an B1iSN-Error:
DI Error: (-10) You cannot select batch or serial numbers for a closed row
Any ideas to solve that Error? Thanks.
Regards,
GB

Hi Bastian,
I have still one open question. How to tread Document Lines Additional Expenses?
If I use the logic of visual order I still get the error "You cannot select batch or serial numbers for a closed row".
Example:
<Document_LinesAdditionalExpenses>
-      <row>
           <LineNumber>4</LineNumber>*no expenses*
</row>
-      <row>
           <LineNumber>0</LineNumber>*no expenses*
</row>
-     <row>
           <LineNumber>1</LineNumber>*no expenses*
</row>
-     <row>
           <LineNumber>2</LineNumber>*no expenses*
</row>
-     <row>
           <LineNumber>3</LineNumber>*expenses correct*
           <ExpenseCode>3</ExpenseCode>
           <LineTotal>10.00</LineTotal>
</row>
</Document_LinesAdditionalExpenses>
How can I solve that?
Thanks and regards,
GB

LR3 Web Gallery Sequence Numbering bug?

Anyone else getting this problem with sequence numbering in the web HTML templates? Basically, as you jump through photos the photo number is always stuck on #1, never changes when you go to the next photo - should go 1, 2, 3, 4, 5...
I just sent a bug report but, wondering if anyone else found a fix for this yet.
This is in LR3 on Mac - really trying to do this on TTG Highslide gallery but, same problem occurs in default Lightroom HTML gallery.
Thanks.
******BUG******
Concise problem statement:
Steps to reproduce bug:
1. Go to Web Module
2. Choose default HTML Gallery
3. Under Image Info set Caption to Sequence
Results:
Sequence caption always shows 1/total images.
i.e. 1/10, 1/10, 1/10, 1/10
Expected results:
Sequence should increment current image number / total images as you click through images.
i.e. 1/10, 2/10, 3/10, 4/10

Yeah, still have the numbering problem using the Image Info sequence outputs.
But, if you use the standard Lightroom Flash Gallery it has it's own sequence numbering output (that does not use Image Info captions) and it does work correctly. These show up as 1/9, 2/9, 3/9 etc. on each photo down by the back/next buttons.
Also, the Cell Numbering does work when using the Lightroom HTML Gallery - though, those numbers only appear on the index page not on individual photos.
But, haven't seen a good work-around yet for sequence numbering in Image Info area. Only option there seems to be typing numbers manually into the caption. Or, if you need the caption for other info maybe use one of the IPTC fields like Headline to type in your numbers. You can then do a Custom Setting in web module to have those text fields show up with your photos.
Really hoping we will see a LR 3.1 sometime soon with a fix - should be an easy correction for Adobe.

Administration port - network channel for admin traffic

I am trying to configure a separate channel for Administration traffic on weblogic. I followed the oracle docos and configured the SSL, domain wide admin port, server listen address, ‘admin’ channel.
The issue is admin traffic in not happening through the newly created channel.
L2 network is not getting used. I can’t see any activity in the monitoring tab of new Channel. Also the netstat is showing that the port 9101/9102 is getting used on the 192.168.100.218 and not on 10.254.252.849.
I also tried by setting up the newly created channel weight as 51, but no luck.
Is JMX connectivity related to admin channel?
Any help is highly appreciated. Thanks.
Ipconfig:
Admin: adminserver701.mycompany.internal, 192.168.100.238, 10.254.252.808
Managed: appserver701.mycompany.internal, :192.168.100.218, 10.254.252.849
Domain wide admin port: 9101
Admin:
Listen address –> adminserver701.mycompany.internal
Channel –> admin -> 10.254.252.808/9101
Startup -> -Dweblogic.admin.ListenAddress=admin://10.254.252.808:9101
Managed:(appserver701)
Listen address –> appserver701.mycompany.internal
Admin port override: 9102
Channel –> admin -> 10.254.252.849/9102
Startup -> -Dweblogic.admin.ListenAddress=admin://10.254.252.849:9102
AdminServer Logs:
####<Feb 18, 2013 1:53:33 PM EST> <Info> <JMX> <adminserver701.mycompany.internal> <soa_as> <[STANDBY] ExecuteThread: '2' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1361159613346> <BEA-149512> <JMX Connector Server started at service:jmx:iiop://adminserver701.mycompany.internal:9101/jndi/weblogic.management.mbeanservers.runtime .>
####<Feb 18, 2013 1:53:33 PM EST> <Info> <JMX> <adminserver701.mycompany.internal> <soa_as> <[ACTIVE] ExecuteThread: '0' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1361159613353> <BEA-149512> <JMX Connector Server started at service:jmx:iiop://adminserver701.mycompany.internal:9101/jndi/weblogic.management.mbeanservers.edit .>
####<Feb 18, 2013 1:53:33 PM EST> <Info> <JMX> <adminserver701.mycompany.internal> <soa_as> <[STANDBY] ExecuteThread: '1' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1361159613367> <BEA-149512> <JMX Connector Server started at service:jmx:iiop://adminserver701.mycompany.internal:9101/jndi/weblogic.management.mbeanservers.domainruntime .>
####<Feb 18, 2013 1:53:36 PM EST> <Notice> <Server> <adminserver701.mycompany.internal> <soa_as> <[ACTIVE] ExecuteThread: '0' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1361159616699> <BEA-002613> <Channel "DefaultAdministration" is now listening on 192.168.100.238:9101 for protocols admin, ldaps, https.>
####<Feb 18, 2013 1:53:36 PM EST> <Notice> <Server> <adminserver701.mycompany.internal> <soa_as> <[ACTIVE] ExecuteThread: '0' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1361159616700> <BEA-002613> <Channel "Channel-0" is now listening on 10.254.252.808:9101 for protocols admin, ldaps, https.>
####<Feb 18, 2013 1:55:12 PM EST> <Notice> <Server> <adminserver701.mycompany.internal> <soa_as> <[ACTIVE] ExecuteThread: '2' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <cd259038c7dcf5a8:-26ac3ba0:13ceb6f767d:-8000-000000000000001a> <1361159712920> <BEA-002613> <Channel "Default" is now listening on 192.168.100.238:7001 for protocols iiop, t3, ldap, snmp, http.>
####<Feb 18, 2013 1:55:12 PM EST> <Notice> <Server> <adminserver701.mycompany.internal> <soa_as> <[ACTIVE] ExecuteThread: '2' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <cd259038c7dcf5a8:-26ac3ba0:13ceb6f767d:-8000-000000000000001a> <1361159712920> <BEA-002613> <Channel "DefaultSecure" is now listening on 192.168.100.238:7002 for protocols iiops, t3s, ldaps, https.>
ManagedServer Logs:
####<Feb 18, 2013 2:54:19 PM EST> <Info> <JMX> <appserver701.mycompany.internal> <adp_ms01> <[ACTIVE] ExecuteThread: '0' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1361163259911> <BEA-149512> <JMX Connector Server started at service:jmx:iiop://appserver701.mycompany.internal:9102/jndi/weblogic.management.mbeanservers.runtime .>
####<Feb 18, 2013 2:54:20 PM EST> <Notice> <Server> <appserver701.mycompany.internal> <adp_ms01> <[ACTIVE] ExecuteThread: '0' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1361163260350> <BEA-002613> <Channel "Channel-0" is now listening on 10.254.252.849:9102 for protocols admin, CLUSTER-BROADCAST-SECURE, ldaps, https.>
####<Feb 18, 2013 2:54:20 PM EST> <Notice> <Server> <appserver701.mycompany.internal> <adp_ms01> <[ACTIVE] ExecuteThread: '0' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1361163260350> <BEA-002613> <Channel "DefaultAdministration" is now listening on 192.168.100.218:9102 for protocols admin, CLUSTER-BROADCAST-SECURE, ldaps, https.>
####<Feb 18, 2013 2:54:58 PM EST> <Notice> <Server> <appserver701.mycompany.internal> <adp_ms01> <[STANDBY] ExecuteThread: '3' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <d3208ed6c2482016:-46ac5fed:13ceba69a8e:-7ffe-000000000000000e> <1361163298045> <BEA-002613> <Channel "DefaultSecure" is now listening on 192.168.100.218:7102 for protocols iiops, t3s, CLUSTER-BROADCAST-SECURE, ldaps, https.>
####<Feb 18, 2013 2:54:58 PM EST> <Notice> <Server> <appserver701.mycompany.internal> <adp_ms01> <[STANDBY] ExecuteThread: '3' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <d3208ed6c2482016:-46ac5fed:13ceba69a8e:-7ffe-000000000000000e> <1361163298045> <BEA-002613> <Channel "Default" is now listening on 192.168.100.218:7101 for protocols iiop, t3, CLUSTER-BROADCAST, ldap, snmp, http.>
AdminServer logs update while starting managed:
####<Feb 18, 2013 2:54:57 PM EST> <Info> <JMX> <adminserver701.mycompany.internal> <soa_as> <[ACTIVE] ExecuteThread: '0' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <cd259038c7dcf5a8:-26ac3ba0:13ceb6f767d:-8000-0000000000000162> <1361163297488> <BEA-149506> <Established JMX Connectivity with adp_ms01 at the JMX Service URL of service: jmx:admin://appserver701.mycompany.internal:9102 /jndi/weblogic.management.mbeanservers.runtime.>
Admin Server :
[oracle@adminserver701 bin]$ netstat -an | grep 9101
tcp 0 0 10.254.252.808:9101 0.0.0.0:* LISTEN
tcp 0 0 192.168.100.238:9101 0.0.0.0:* LISTEN
tcp 0 0 192.168.100.238:9101 192.168.100.218:59038 ESTABLISHED
I am wondering if the JMX connectivity is using the server listen address (adminserver701.mycompany.internal) which will by default resolve to 192.168.100.238. Is there a way to force JMX to use 10.254.252.808?

Hi
For first question the answer is no. With the administration port, you enable the SSL between the admin server and Node manager-managed Servers. You can still use the web console.
For teh second question, you can use ANT or can use the WLS Scripting ..you can get more details in dev2dev.bea.com
Jin

Ignoring TCP handshake & Sequence Numbers for STT Traffic

Similar Messages

Maybe you are looking for