Initial privilege level for http/https login on Aironet

When browsing to 1131 & 1242 via https, the password prompted for is level 1:
"level_1_or_view_access"
I would like this initial access to prompt for level 15 password or, at worst, level 2. Is there any way to change the level of initial access via http/https?
Thanks in Advance

To clarify, I wish to disallow web login for users with level 1 privileges.

Similar Messages

Default Privilege Level for ASA users authenticated by Radius or TACACS when using ASDM

Hello,
I'm trying to figure out what the default privilege level is for users that are authenticated to the ASA via a remote authentication server when using the ASDM.
the command "aaa authentication http console TACACS+ LOCAL" is used in the ASA config.
The remote server is NOT setting any privilege levels for users. There are also no aaa authorization commands present in the config.
So what privilege level do the users receive when they login with the ASDM? I'm being told that the users receive admin access which includes config write, reboot, and debug. But I cannot find any documentation stating hte default level.
Please advise. And providing links to cisco documentation would be great too.
Thanks,
Brendan

Hi Berendan,
Hope the below exerpt from document clarifies your query. also i have provided the link to refer.
About Authorization
Authorization controls access per user after users authenticate. You can configure the security appliance to authorize the following items:
•Management commands
•Network access
•VPN access
Authorization controls the services and commands available to each authenticated user. Were you not to enable authorization, authentication alone would provide the same access to services for all authenticated users.
If you need the control that authorization provides, you can configure a broad authentication rule, and then have a detailed authorization configuration. For example, you authenticate inside users who attempt to access any server on the outside network and then limit the outside servers that a particular user can access using authorization.
The security appliance caches the first 16 authorization requests per user, so if the user accesses the same services during the current authentication session, the security appliance does not resend the request to the authorization server.
http://www.cisco.com/c/en/us/td/docs/security/asa/asa80/asdm60/user/guide/usrguide/aaasetup.html
Regards
Karthik

Privilege level for the commands

Hi All,
I am trying to modify the privilege level of the commands in my router.
I need to understand what is the privilege level for the commands.
Is there a command in the IOS or a link with a document on the CCO with the criteria or the list of the command and its corresponded privile level.
Thanks
Matteo

Matteo
I am not clear what it is that you are trying to do. But let me make a suggestion. While there are 16 privilege levels (0 through 15) there are two levels that are commonly used 1 and 15. 1 is what is usually called user mode and is the default level when someone first logs into the router. My suggestion is to identify what group of commands you do not want to be available in user mode, decide if they should be available in something less than 15, pick a level, and assign the commands to that level.
If you really do want to start from a list of commands and their privilege level, I do not think that you will find any single source which will accurately give you the privilege level for all commands. The closest you will find is to look in the command reference and find the command. The command reference will usually describe the privilege level. Unfortunately I have found a few situations where the description of privilege level was not correct.
My advice is that if you want to find the privilege level for some commands that you want to manipulate, that you get a router and try the command and determine what its privilege level is.
HTH
Rick

PRIVILEGE LEVELS FOR ACS WITH AD DATABASE

How do I configure two separate privilige levels for two groups. These groups exist in the AD database i.e. my ACS (Pri & Backup) are looking in AD for authentication.

Hi ,
If you are using TACACS ,
Bring users/groups in at level needed
1. Go to user or group setup in ACS
2. Drop down to "TACACS+ Settings"
3. Place a check in "Shell (Exec)"
4. Place a check in "Privilege level" and enter " priv "(1 to 15) in the adjacent field
If you are using RADIUS,
aaa new-model
aaa authentication login default group radius local
aaa authorization exec default group radius local
radius-server host X.X.X.X key XXXX
Following is the configuration required in the Radius Server
The AV pair in the ACS -->group setup--> IETF RADIUS Attributes
[006] Service-Type = Login
/* Following is for getting the user straight in privledge mode */ to set priv 15
The AV pair in Cisco IOS/PIX RADIUS Attributes
[009\001] cisco-av-pair = shell:priv-lvl=15
For more information on above commands, please refer to the following link :-
http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122cgcr/fsec
ur_c/fsaaa/index.htm
Please try the above and let me know if this helps.
Thanks

Setting privilege level for logging into ASA through ACS

Hi!,
In my environment i implemented AAA for logging into switches, routers, asa etc through ACS which is being configured TACACS+.
I have set different privilege levels like readonly, readwrite etc into ACS. There are working fine when i try to login into switch or router.
But in ASA i am unable to restrict the privilege levels of different users.
Can someone plz guide me with ASA & ACS setting to solve this issue!!!!!

Hi!!
I tried this option. It is working fine with routers & switches. But for ASA privilege access it is not functioning.
I created 3 profiles in "Shared Profiles" & added 1 of them in Group setting & added users to this group with mentioning group authentication. This way i am able to control access to the switches & routers with proper privilege. But the same way when i tried to impolement ASA it's not happening.
Can u plz check it out...

Change in privilege level for the command show logging

I have recently discovered a change in behavior in IOS. The command show logging has traditionally been available at user level. Now it has become a privilege level 15 command.
I thought that this was strange and opened a case with Cisco TAC about it. I was told that this is a new "feature" that was implemented for bugid CSCsl61281. Unfortunately this bugid is viewable by Cisco internally but not viewable by the public.
The TAC engineer tells me that this change is integrated into these releases:
This was integrated into the following releases:
12.4(24.05.01)PIX11
12.4(21.14.09)PIC01
12.4(19.03)T
12.2(52.23)SIN
12.2(33)SXI01
12.2(32.08.11)SX229
12.2(32.08.11)SR174
I do not think that this is a good change. If you do not think that this is a good change I suggest that you contact your Cisco support team and express your opinion about this change.
Otherwise as you go to new versions of IOS be aware of the potential impact on your network monitoring processes and procedures that show logging will require level 15 privilege access.
HTH
Rick

Hi Rick,
Can you suggest me references to know more about privilege level commands?
How to enable different commands for different levels of privileges?
Thanks.
-Sudhish

Aironet 1600 privilege level for MAC Filtering

   Hi,
I want to permit from a user profile with the telnet CLI command to configure the new MAC address on the dot11 association mac-list 700
I have create the user 14 with the followed commands:
enable secret level 14 5 **************
enable secret 5 **************
privilege configure level 14 access-list
privilege exec level 14 write memory
privilege exec level 14 write
privilege exec level 14 configure terminal
privilege exec level 14 configure
privilege exec level 14 show dot11 associations client
privilege exec level 14 show dot11 associations
privilege exec level 14 show dot11
privilege exec level 14 show access-lists
privilege exec level 14 show
Access from login privilege 14
1602AP16#show privile
Current privilege level is 14
1602AP16#show access-l
Bridge address access list 700
    permit 100b.a965.7384   0000.0000.0000 (2 matches)
    permit 0026.c659.b182   0000.0000.0000
    permit 0019.d2c2.96c0   0000.0000.0000
OK
add the new MAC address
1602AP16(config)#access-list ?
<1-99>       IP standard access list
<100-199>    IP extended access list
<1100-1199> Extended 48-bit MAC address access list
<1300-1999> IP standard access list (expanded range)
<200-299>    Protocol type-code access list
<2000-2699> IP extended access list (expanded range)
<700-799>    48-bit MAC address access list
1602AP16(config)#access-list 700 permit 0026.c659.b182   0000.0000.0000
                                                               ^
% Invalid input detected at '^' marker.
I can open the user level 14 config and when I add the new MAC address I received the " Invalid input detected " message
What is wrong ?
Is it only permit at level 15 ?
IOS version :
Cisco IOS Software, C1600 Software (AP1G2-K9W7-M), Version 15.2(2)JB, RELEASE SOFTWARE (fc1)
Thank you to shared me yours comments !
Patrick

Hi Patric,
Can u try this :
privilege configure level 14 access-list
and all other with priv 13.
privilege exec level 13 write memory
privilege exec level 13 write
privilege exec level 13 configure terminal
privilege exec level 13 configure
privilege exec level 13 show dot11 associations client
privilege exec level 13 show dot11 associations
privilege exec level 13 show dot11
privilege exec level 13 show access-lists
privilege exec level 13 show
and then try to configure it.
If still fails then u must use priv 15 .
Regards

Custom privilege level for CSM commands

Is there a way to creat a custom privilege level to allow a user access to only CSM config commands while in config mode?? I'm trying to allow members of our server/web team to check on the status of the web servers and to take them out of service for maintenance....and not allow them access to change any other configs on the switch.
Thanks...Jeff

Here is an exampel for enable 5
enable secret level 5
privilege slb-lam-mode-real level 5 no inservice
privilege slb-lam-mode-real level 5 inservice
privilege slb-lam-mode-real level 5 inservice standby
privilege slb-lam-mode-csm-sfarm level 5 real
privilege slb-lam-mode-csm-sfarm level 5 real name
privilege slb-lam-mode-csm level 5 server
privilege configure level 5 module csm
privilege exec level 5 conf t
privilege exec level 5 exit

User privilege level for configuration backup with PI 1.2

We have more than 50 devices handling by PI 1.2 (testing) I like to know how to do configuration archiving with user who doesn't have write privilege.
I tried like this.
username john privilege 6 password cisco
privilege exec level 6 show running-config
(result) show run --> blank
I tried this user with one of switch in PI 1.2. It did not do configuration backup
username inout password inout
username inout privilege 15 autocommand show running-config
(result) once logged in, it automatically showed running-config. However when I tried with PI 1.2 with this user (inout). I couldn't do configuration back.
reference
http://www.cisco.com/en/US/tech/tk59/technologies_tech_note09186a00800949d5.shtml
so, my question is this. what is the solution for me to create certain user with read-only privilege while PI 1.2 is able to do configuration archiving ?
thanks in advance

7.4 MSE code will in fact require an update of Prime 1.2 to 1.3.0.20-
It's pretty easy though and your licenses will still work from the Prime Infra side.
Here's a link to upgrade PI to 1.3
http://www.cisco.com/en/US/partner/docs/net_mgmt/prime/infrastructure/1.3/release/notes/cpi_rn_13.html#wp73605
I personally would go ahead with the upgrade of both:::

Privilege Level for Tacacs Account in Nexus 7000

Hi,
I have configured the Tacacs (ACS 4.2v) on Nexus 7000 (as mentioned below) and works fine but unlike IOS (6509) It's doesn't prompt that you are in userexec mode (>) and then need to type enable and password for full privilege.
In n7k when I entered into "configure terminal" It won't allow me to access other commands.
How to login into level 15 privilege mode after authenticating from tacacs
(config)# show running-config tacacs+
tacacs-server key 7 "xxxxx"
tacacs-server host x.x.x.x key 7 "xxxx"
aaa group server tacacs+ TacServer
    server x.x.x.x (same ip as tacacs-server host)
    use-vrf management
    source-interface Vlan2
(config)# show running-config aaa
aaa authentication login default group TacServer
aaa authentication login console local
aaa user default-role
Here below are the commands accessible in "Terminal" currently
(config)# ?
no        Negate a command or set its defaults
username Configure user information.
end       Go to exec mode
exit      Exit from command interpreter
isb.n7k-dcn-agg-1-sw(config)#

Hi Jan.nielsen
Issue is resolved but by another way.
I have found the same resolution too of custom attirbute command but the Custom attribute Option for shell command wasn't available in ACS v4.2, so after enabling shell for users and by clicking exec--> Shell Exec and enabling priviledge level 15 in the same box of Shell options, It start working without any command

Configure Read-Acces via user-defined privilege level

Hello everybody,
I´m looking for the best configuration to restrict a user to read-only. The restriction should be configured via CLI not TACACS+.
Hardware: 3750 (probably not interesting for this question)
Oldest IOS: 12.2(53)SE1
The user should be allowed to:
see the running-configuration
trigger all kinds of show-commands
ping and traceroute from the device
The user should not be allowed to:
upload/delete/rename files on the flash-memory
get into level 15 (not sure if I can avoid this)
all other commands despite those from level 1 and those specified above
Can someone help me with this?
Thanks in advance!
I won´t forget to rate helpful posts

Hi Tobias,
You can
configure Multiple Privilege Levels on a switch as explained below.
By default, the Cisco IOS software has two modes of password security: user EXEC and
privileged EXEC. You can configure up to 16 hierarchical levels of commands for each mode.
By configuring multiple passwords, you can allow different sets of users to have access to
specified commands.
For example, if you want many users to have access to the clear line command, you can
assign it level 2 security and distribute the level 2 password fairly widely. But if you
want more restricted access to the configure command, you can assign it level 3 security
and distribute that password to a more restricted group of users.
Setting the Privilege Level for a Command
Beginning in privileged EXEC mode, follow these steps to set the privilege level for a
command mode:
     Command Purpose
      Step 1
     configure terminal
     Enter global configuration mode.
      Step 2
     privilege mode level level command
     Set the privilege level for a command.
For mode, enter configure for global configuration mode, exec for EXEC mode, interface
for interface configuration mode, or line for line configuration mode.
For level, the range is from 0 to 15. Level 1 is for normal user EXEC mode privileges.
Level 15 is the level of access permitted by the enable password.
For command, specify the command to which you want to restrict access.
      Step 3
     enable password level level password
     Specify the enable password for the privilege level.
.For level, the range is from 0 to 15. Level 1 is for normal user EXEC mode privileges.
For password, specify a string from 1 to 25 alphanumeric characters. The string cannot
start with a number, is case sensitive, and allows spaces but ignores leading spaces. By
default, no password is defined.
      Step 4
     end
     Return to privileged EXEC mode.
      Step 5
     show running-config
     or
      show privilege
     Verify your entries.
The first command shows the password and access level configuration. The second command
shows the privilege level configuration.
      Step 6
     copy running-config startup-config
     (Optional) Save your entries in the configuration file.
When you set a command to a privilege level, all commands whose syntax is a subset of that
command are also set to that level. For example, if you set the show ip traffic command to
level 15, the show commands and show ip commands are automatically set to privilege level
15 unless you set them individually to different levels.
To return to the default privilege for a given command, use the no privilege mode level
level command global configuration command.
This example shows how to set the configure command to privilege level 14 and define
SecretPswd14 as the password users must enter to use level 14 commands:
Switch(config)# privilege exec level 14 configure
Switch(config)# enable password level 14 SecretPswd14
Also you can change the default privilege level for all the users .
Changing the Default Privilege Level for Lines Beginning in privileged EXEC mode, follow these steps to change the default privilege level for a line:    Command Purpose
Step 1   configure terminal Enter global configuration mode.
Step 2   line vty line Select the virtual terminal line on which to restrict access.
Step 3   privilege level level Change the default privilege level for the line.
             For level, the range is from 0 to 15. Level 1 is for normal user EXEC mode
             privileges. Level 15 is the level of access permitted by the enable password.
Step 4 end Return to privileged EXEC mode.
Step 5   show running-config or show privilege
          Verify your entries. The first command shows the password and access level configuration.
          The second command shows the privilege level configuration.
Step 6   copy running-config startup-config (Optional) Save your entries in the configuration file.
Users can override the privilege level you set using the privilege level line configuration command
by logging in to the line and enabling a different privilege level.
They can lower the privilege level by using the disable command.
If users know the password to a higher privilege level, they can use that password to enable the higher privilege level. You might specify a high level or privilege level for your console line to restrict line usage.
To return to the default line privilege level, use the no privilege level line configuration command. Also i am sending a document for your reference.
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat3750/12225see/scg/swauthen.htm#wp1154063
HTH
Regards
Inayath

Aaa radius server control privilege level

I've got radius authentication working on my switch, but I'm trying to allow two types of users login using Windows Active Directory. NetworkUsers who can view configuration and NetworkAdmins who can do anything. I would like for NetworkAdmins to when they login go directly into privilege level 15 but cant get that part to work. Here is my setup:
Windows 2008 R2 Domain controller with NPS installed.
Radius client: I have the IP of the switch along with the key. I have cisco selected under the vendor name in the advance tab
Network Policies:
NetworkAdmins which has the networkadmin group under conditions and under settings i have nothing listed under Standard and for Vendor Specific i have :
Cisco-AV-Pair Cisco shell:priv-lvl=15
My switch config:
aaa new-model
aaa group server radius MTFAAA
server name dc-01
server name dc-02
aaa authentication login NetworkAdmins group MTFAAA local
aaa authorization exec NetworkAdmins group MTFAAA local
radius server dc-01
address ipv4 10.0.1.10 auth-port 1645 acct-port 1646
key 7 ******
radius server dc-02
address ipv4 10.0.1.11 auth-port 1645 acct-port 1646
key 7 ******
No matter what i do it doesnt default to privilege level 15 when i login. Any thoughts

Have you specified the authorization exec group under line vty? I think it is authorization exec command. Something like that.

Assigning Privilege Level Thru RADIUS

I'm using Microsoft IAS as my RADIUS server. We have a number of Cisco 2800 routers running the latest IOS which are also acting as VPN servers for our remote user connecting using their laptops via IPSec and Cisco VPN Client. How can I set the privilege level for the authenticated users so that the remote VPN users are given privilege level 0 and the Administrators are given privilege level 15, so they can login to routers and manage them.

Prem
Thanks for attaching a very interesting document. worth the 5 rating.
HTH
Rick

Privilege Level to view flash (https server)

Hello community,
I've been digging around and I don't think I'm asking the right question, so I thought I'd ask it here. I've been working a little bit with Cisco native IOS HTTP/HTTPS server.
I've put together a SSI (.shtml) page to pull data from my router, and display it in an easy to read format for quick and simple troubleshooting. The thing is, is that I must be a lvl 15 user to access this file when it's loaded onto flash.
To get around this, I felt it would be easier to grant users lvl 1 SSH access and have them authenticate against a RADIUS server. Although that gets around the issue, I'd still really like to try and figure this out. I'd like to know what I need to do to make it so that a lvl 1-14 user can log into the IOS https server, and open my .shtml page without it prompting for lvl 15 authentication.
(I can login with my test user (privilege lvl 1) to the HTTPS server without issue. It's when I try and browse to: https://router/level/01/file.shtml , that's when I'm prompted to login as lvl 15.)
Thanks in advance everyone. Your assistance / insight into this would be very much appreciated!

this is what fixed the issuefor me:
Be sure to try this on a test machine and back it up if needed.
In the system registry
For each of the following registry keys:
HKEY_CLASSES_ROOT\CLSID\{D27CDB6E-AE6D-11cf-96B8-444553540000}
HKEY_CLASSES_ROOT\CLSID\{D27CDB70-AE6D-11cf-96B8-444553540000}
HKEY_CLASSES_ROOT\CLSID\{1171A62F-05D2-11D1-83FC-00A0C9089C5A}
HKEY_CLASSES_ROOT\TypeLib\{D27CDB6B-AE6D-11CF-96B8-444553540000}
Right-click the key, select "Permissions"
In the Permissions Dialog click the "Advanced" button Click "Add"
Enter "Everyone" and click "OK" to accept Select "Allow" for the "Query Value", "Enumerate Subkeys", "Notify" and "Read Control" permissions. Do not change any existing permissions.
Source - http://www.adobe.com/go/624850b5

How to set more detail log level for http

Hi,
With Java Enterprise System 2003 I want to see when a user login to the Messenger Express in the http log. How could I set a log level so I can see this?
I do not know the the default log level for http and I would like to set a log level that show me more information
could this be the command?
configutil -o logfile.http.loglevel -v level Information

configutil -o logfile.http.loglevel -v Information
would be the correct command to set the log level to "information".
Other valid levels include, "debug", "notice" (this is the default), "warning".
You have t restart the webmail daemon to make this take effect.
stop-msg http; start-msg http

Initial privilege level for http/https login on Aironet

Similar Messages

Maybe you are looking for