PRIVILEGE LEVELS FOR ACS WITH AD DATABASE

How do I configure two separate privilige levels for two groups. These groups exist in the AD database i.e. my ACS (Pri & Backup) are looking in AD for authentication.

Hi ,
If you are using TACACS ,
Bring users/groups in at level needed
1. Go to user or group setup in ACS
2. Drop down to "TACACS+ Settings"
3. Place a check in "Shell (Exec)"
4. Place a check in "Privilege level" and enter " priv "(1 to 15) in the adjacent field
If you are using RADIUS,
aaa new-model
aaa authentication login default group radius local
aaa authorization exec default group radius local
radius-server host X.X.X.X key XXXX
Following is the configuration required in the Radius Server
The AV pair in the ACS -->group setup--> IETF RADIUS Attributes
[006] Service-Type = Login
/* Following is for getting the user straight in privledge mode */ to set priv 15
The AV pair in Cisco IOS/PIX RADIUS Attributes
[009\001] cisco-av-pair = shell:priv-lvl=15
For more information on above commands, please refer to the following link :-
http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122cgcr/fsec
ur_c/fsaaa/index.htm
Please try the above and let me know if this helps.
Thanks

Similar Messages

  • Default Privilege Level for ASA users authenticated by Radius or TACACS when using ASDM

    Hello,
    I'm trying to figure out what the default privilege level is for users that are authenticated to the ASA via a remote authentication server when using the ASDM.
    the command "aaa authentication http console TACACS+ LOCAL" is used in the ASA config.
    The remote server is NOT setting any privilege levels for users.  There are also no aaa authorization commands present in the config.
    So what privilege level do the users receive when they login with the ASDM?  I'm being told that the users receive admin access which includes config write, reboot, and debug.  But I cannot find any documentation stating hte default level.
    Please advise.  And providing links to cisco documentation would be great too.
    Thanks,
    Brendan

    Hi Berendan,
    Hope the below exerpt from document clarifies your query. also i have provided the link to refer.
    About Authorization
    Authorization controls access per user after users authenticate. You can configure the security appliance to authorize the following items:
    •Management commands
    •Network access
    •VPN access
    Authorization controls the services and commands available to each authenticated user. Were you not to enable authorization, authentication alone would provide the same access to services for all authenticated users.
    If you need the control that authorization provides, you can configure a broad authentication rule, and then have a detailed authorization configuration. For example, you authenticate inside users who attempt to access any server on the outside network and then limit the outside servers that a particular user can access using authorization.
    The security appliance caches the first 16 authorization requests per user, so if the user accesses the same services during the current authentication session, the security appliance does not resend the request to the authorization server.
    http://www.cisco.com/c/en/us/td/docs/security/asa/asa80/asdm60/user/guide/usrguide/aaasetup.html
    Regards
    Karthik

  • Recommended Patch Level for ACS 4.2

    Hi,
    Is there a recommended patch level for ACS 4.2? I see a patch 4 and 5 can be downloaded. Any gotchas with either?
    thanks
    Bob

    Bob,
    I haven't had any issues with patch 5 for ACS 4.2. If you have any concerns please see the release notes for the patch.
    HTH,
    Mark

  • Privilege level for the commands

    Hi All,
    I am trying to modify the privilege level of the commands in my router.
    I need to understand what is the privilege level for the commands.
    Is there a command in the IOS or a link with a document on the CCO with the criteria or the list of the command and its corresponded privile level.
    Thanks
    Matteo

    Matteo
    I am not clear what it is that you are trying to do. But let me make a suggestion. While there are 16 privilege levels (0 through 15) there are two levels that are commonly used 1 and 15. 1 is what is usually called user mode and is the default level when someone first logs into the router. My suggestion is to identify what group of commands you do not want to be available in user mode, decide if they should be available in something less than 15, pick a level, and assign the commands to that level.
    If you really do want to start from a list of commands and their privilege level, I do not think that you will find any single source which will accurately give you the privilege level for all commands. The closest you will find is to look in the command reference and find the command. The command reference will usually describe the privilege level. Unfortunately I have found a few situations where the description of privilege level was not correct.
    My advice is that if you want to find the privilege level for some commands that you want to manipulate, that you get a router and try the command and determine what its privilege level is.
    HTH
    Rick

  • Workflow: Auto forward for next level for decision with object (RFQ)

    Hi all,
    I have the same requirement as the one in this post but for RFQ approval instead of PO
    Workflow -Auto forward for next level for decision with object (PR)
    I have tried deadline monitoring, but I need to capture the level in which the RFQ is in order to escalate.
    Can someone let me know how to proceed further.
    Regards,
    nsp.

    Hi Aamir,
    As you said we have to use deadline monitoring here.
    For this case use 'Requested Start'. From your i came to know this workitem should be a dialog workitem, so the workflow will wait for the time what you have specified in the requested start and when it is reached it places the workitem in the corresponding recipient inbox.
    Regards
    Balaji E.

  • Setting privilege level for logging into ASA through ACS

    Hi!,
    In my environment i implemented AAA for logging into switches, routers, asa etc through ACS which is being configured TACACS+.
    I have set different privilege levels like readonly, readwrite etc into ACS. There are working fine when i try to login into switch or router.
    But in ASA i am unable to restrict the privilege levels of different users.
    Can someone plz guide me with ASA & ACS setting to solve this issue!!!!!

    Hi!!
    I tried this option. It is working fine with routers & switches. But for ASA privilege access it is not functioning.
    I created 3 profiles in "Shared Profiles" & added 1 of them in Group setting & added users to this group with mentioning group authentication. This way i am able to control access to the switches & routers with proper privilege. But the same way when i tried to impolement ASA it's not happening.
    Can u plz check it out...

  • Enabling Privilege Levels when ACS is Down

    Hi,
    I have a requirement to fall back to local accounts when ACS is down. These accounts will have specific privilege levels. I have two local users - adminro and adminrw.
    adminro is read only and will have a privilege level of 7.
    adminrw is a full access account with a priv level of 15.
    I can login with adminro when ACS is down, but when I attempt to enable using "enable 7" I receive the following ouput:
    PPD-ELPUF5/pri/act> en 7
    Enabling to privilege levels is not allowed when configured for
    AAA authentication. Use 'enable' only.
    If I login using "enable", my read only account now has full configuration access which is not desireable.
    My AAA configuration is as follows:
    aaa authentication ssh console ADMIN LOCAL
    aaa authentication enable console ADMIN LOCAL
    aaa authentication http console ADMIN LOCAL
    aaa authentication telnet console ADMIN LOCAL
    aaa authentication serial console ADMIN LOCAL
    aaa authorization command ADMIN LOCAL
    aaa accounting ssh console ADMIN
    aaa accounting command privilege 15 ADMIN
    aaa accounting enable console ADMIN
    aaa accounting serial console ADMIN
    aaa accounting telnet console ADMIN
    aaa authorization exec authentication-server
    username adminro password <REMOVED> encrypted privilege 7
    username adminrw password <REMOVED> encrypted privilege 15
    enable password <REMOVED> level 7 encrypted
    enable password <REMOVED> encrypted
    Is there anyway to enable the user or automatically elevate the user to privilege 7 post login like you can with a router? I cannot have the adminro account to be able to run configuration commands on the device. Running ASA version 8.2(3).
    Thanks!

    PPD-ELPUF5/pri/act# sh curpriv
    Username : adminro
    Current privilege level : 7
    Current Mode/s : P_PRIV
    Server Group:    ADMIN
    Server Protocol: tacacs+
    Server Address:  1.150.1.80
    Server port:     49
    Server status:   FAILED, Server disabled at 15:02:37 EDT Wed Oct 12 2011
    Number of pending requests              0
    Average round trip time                 2ms
    Number of authentication requests       38
    Number of authorization requests        373
    Number of accounting requests           149
    Number of retransmissions               0
    Number of accepts                       307
    Number of rejects                       19
    Number of challenges                    0
    Number of malformed responses           0
    Number of bad authenticators            0
    Number of timeouts                      234
    Number of unrecognized responses        0
    PPD-ELPUF5/pri/act(config)# name 1.1.1.1 TEST description TEST CHANGE
    PPD-ELPUF5/pri/act(config)# sh run name
    name 1.1.1.1 TEST description TEST CHANGE
    As you can see above, my user was able to perform a change even though it should not be allowed.
    PPD-ELPUF5/pri/act(config)# sh run privilege
    privilege cmd level 7 mode exec command show
    privilege cmd level 7 mode exec command ping
    privilege cmd level 7 mode exec command traceroute

  • Change in privilege level for the command show logging

    I have recently discovered a change in behavior in IOS. The command show logging has traditionally been available at user level. Now it has become a privilege level 15 command.
    I thought that this was strange and opened a case with Cisco TAC about it. I was told that this is a new "feature" that was implemented for bugid CSCsl61281. Unfortunately this bugid is viewable by Cisco internally but not viewable by the public.
    The TAC engineer tells me that this change is integrated into these releases:
    This was integrated into the following releases:
    12.4(24.05.01)PIX11
    12.4(21.14.09)PIC01
    12.4(19.03)T
    12.2(52.23)SIN
    12.2(33)SXI01
    12.2(32.08.11)SX229
    12.2(32.08.11)SR174
    I do not think that this is a good change. If you do not think that this is a good change I suggest that you contact your Cisco support team and express your opinion about this change.
    Otherwise as you go to new versions of IOS be aware of the potential impact on your network monitoring processes and procedures that show logging will require level 15 privilege access.
    HTH
    Rick

    Hi Rick,
    Can you suggest me references to know more about privilege level commands?
    How to enable different commands for different levels of privileges?
    Thanks.
    -Sudhish

  • Initial privilege level for http/https login on Aironet

    When browsing to 1131 & 1242 via https, the password prompted for is level 1:
    "level_1_or_view_access"
    I would like this initial access to prompt for level 15 password or, at worst, level 2. Is there any way to change the level of initial access via http/https?
    Thanks in Advance

    To clarify, I wish to disallow web login for users with level 1 privileges.

  • Workflow -Auto forward for next level for decision with object (PR)

    Dear All,
    I am working on PR release through workflow, with three level release codes. I need your help in setting:-
    Example:
    In case PR received through workflow at 1st level for release code Z1, and if he could not able to release it within 5 Min, PR/task should be automatically forwarded to next 2nd level for release code Z2.
    And in case 2nd level do not release within 10 Min, PR/task should be farwarded to 3rd level for decision
    etc etc
    It is some thing with lastet End, Request Start, Latest Start & Request End , but could not able to understand how to work with them in case of above situation.
    Any tips/link/document would be great for me?
    Regards
    Aamir

    Hi Aamir,
    As you said we have to use deadline monitoring here.
    For this case use 'Requested Start'. From your i came to know this workitem should be a dialog workitem, so the workflow will wait for the time what you have specified in the requested start and when it is reached it places the workitem in the corresponding recipient inbox.
    Regards
    Balaji E.

  • Aironet 1600 privilege level for MAC Filtering

       Hi,
    I want to permit from a user profile with the telnet CLI command to configure the new MAC address on the dot11 association mac-list 700
    I have create the user 14 with the followed commands:
    enable secret level 14 5 **************
    enable secret 5 **************
    privilege configure level 14 access-list
    privilege exec level 14 write memory
    privilege exec level 14 write
    privilege exec level 14 configure terminal
    privilege exec level 14 configure
    privilege exec level 14 show dot11 associations client
    privilege exec level 14 show dot11 associations
    privilege exec level 14 show dot11
    privilege exec level 14 show access-lists
    privilege exec level 14 show
    Access from login privilege 14
    1602AP16#show privile
    Current privilege level is 14
    1602AP16#show access-l
    Bridge address access list 700
        permit 100b.a965.7384   0000.0000.0000 (2 matches)
        permit 0026.c659.b182   0000.0000.0000
        permit 0019.d2c2.96c0   0000.0000.0000
    OK
    add the new MAC address
    1602AP16(config)#access-list ?                                        
      <1-99>       IP standard access list
      <100-199>    IP extended access list
      <1100-1199>  Extended 48-bit MAC address access list
      <1300-1999>  IP standard access list (expanded range)
      <200-299>    Protocol type-code access list
      <2000-2699>  IP extended access list (expanded range)
      <700-799>    48-bit MAC address access list
    1602AP16(config)#access-list 700 permit 0026.c659.b182   0000.0000.0000
                                                                   ^
    % Invalid input detected at '^' marker.
    I can open the user level 14 config and when I add the new MAC address I received the " Invalid input detected " message
    What is wrong ?
    Is it only permit at level 15 ?
    IOS version : 
    Cisco IOS Software, C1600 Software (AP1G2-K9W7-M), Version 15.2(2)JB, RELEASE SOFTWARE (fc1)
    Thank you to shared me yours comments !
    Patrick

    Hi Patric,
    Can u try this :
    privilege configure level 14 access-list
    and all other with priv 13.
    privilege exec level 13 write memory
    privilege exec level 13 write
    privilege exec level 13 configure terminal
    privilege exec level 13 configure
    privilege exec level 13 show dot11 associations client
    privilege exec level 13 show dot11 associations
    privilege exec level 13 show dot11
    privilege exec level 13 show access-lists
    privilege exec level 13 show
    and then try to configure it.
    If still fails then u must use priv 15 .
    Regards

  • Custom privilege level for CSM commands

    Is there a way to creat a custom privilege level to allow a user access to only CSM config commands while in config mode?? I'm trying to allow members of our server/web team to check on the status of the web servers and to take them out of service for maintenance....and not allow them access to change any other configs on the switch.
    Thanks...Jeff

    Here is an exampel for enable 5
    enable secret level 5
    privilege slb-lam-mode-real level 5 no inservice
    privilege slb-lam-mode-real level 5 inservice
    privilege slb-lam-mode-real level 5 inservice standby
    privilege slb-lam-mode-csm-sfarm level 5 real
    privilege slb-lam-mode-csm-sfarm level 5 real name
    privilege slb-lam-mode-csm level 5 server
    privilege configure level 5 module csm
    privilege exec level 5 conf t
    privilege exec level 5 exit

  • User privilege level for configuration backup with PI 1.2

    We have more than 50 devices handling by PI 1.2 (testing) I like to know how to do configuration archiving with user who doesn't have write privilege.
    I tried like this.
    username john privilege 6 password cisco
    privilege exec level 6 show running-config
    (result) show run --> blank
      I tried this user with one of switch in PI 1.2. It did not do configuration backup
    username inout password inout
    username inout privilege 15 autocommand show running-config
    (result) once logged in, it automatically showed running-config. However when I tried with PI 1.2 with this user (inout). I couldn't do configuration back.
    reference
    http://www.cisco.com/en/US/tech/tk59/technologies_tech_note09186a00800949d5.shtml
    so, my question is this. what is the solution for me to create certain user with read-only privilege while PI 1.2 is able to do configuration archiving ?
    thanks in advance

    7.4 MSE code will in fact require an update of Prime 1.2 to 1.3.0.20-
    It's pretty easy though and your licenses will still work from the Prime Infra side.
    Here's a link to upgrade PI to 1.3
    http://www.cisco.com/en/US/partner/docs/net_mgmt/prime/infrastructure/1.3/release/notes/cpi_rn_13.html#wp73605
    I personally would go ahead with the upgrade of both:::

  • Privilege Level for Tacacs Account in Nexus 7000

    Hi,
    I have configured the Tacacs (ACS 4.2v) on Nexus 7000 (as mentioned below) and works fine but unlike IOS (6509) It's doesn't prompt that you are in userexec mode (>) and then need to type enable and password for full privilege.
    In n7k when I entered into "configure terminal" It won't allow me to access other commands.
    How to login into level 15 privilege mode after authenticating from tacacs
    (config)# show running-config tacacs+
    tacacs-server key 7 "xxxxx"
    tacacs-server host x.x.x.x key 7 "xxxx"
    aaa group server tacacs+ TacServer
        server x.x.x.x (same ip as tacacs-server host)
        use-vrf management
        source-interface Vlan2
    (config)# show running-config aaa
    aaa authentication login default group TacServer
    aaa authentication login console local
    aaa user default-role
    Here below are the commands accessible in "Terminal" currently
    (config)# ?
      no        Negate a command or set its defaults
      username  Configure user information.
      end       Go to exec mode
      exit      Exit from command interpreter
    isb.n7k-dcn-agg-1-sw(config)#

    Hi Jan.nielsen
    Issue is resolved but by another way.
    I have found the same resolution too of custom attirbute command but the Custom attribute Option for shell command wasn't available in ACS v4.2, so after enabling shell for users and by clicking exec--> Shell Exec and enabling priviledge level 15 in the same box of Shell options, It start working without any command

  • Change the recording level for recording with Thunderbolt-Firewire-Mixer

    Hey,
    I just bought a PHONIC Helix Board 24 Universal for recording some music via Firewire.
    Because my IMac has no Firewire-slot, I am using a Thunderbolt-Firewire-Adapter and a Firewire 400-800 cable.
    If I try to record some music it sounds really horrible.
    It seems that the reason is the recording level which can be changed while using the internal micro but not with firewire-Thunderbolt.
    The recording level is set on max, resulting in overmodulation and noise.
    Is there any way to adujust the recording level?
    Thank you in advance!
    Kay

    Hello Jshen6,
    Have you tried looking at the examples in LabVIEW under Hardware Input and Output>>Synchronization? The Analog Input-Synchronization.vi example shows you how to synchronize AI across multiple devices in various configurations and for various types of hardware. Would you mind listing what hardware you are using? Are all three devices taking the same data (voltage, strain, acceleration, etc)?
    Jonathan L.
    Applications Engineer
    National Instruments

Maybe you are looking for