Install errors and Disk Utility failure

Hello!
My current install of Mac OS X must have been a newer install of Panther. The retail install I bought is v10.3.5. I think the install was originally 10.3.7.
I've tried to run Disk Utility from the install Disc 1 and get a message: "*The underlying task reported failure on exit.*"
And I tried to also perform an Archive and install of Mac OS X Panther 10.3.5 and get a message: "*You cannot install Mac OS X on this volume without changing your install settings. A newer version of Mac OS X is installed*."
So, I'm asking what my options are as to keep my current user Home folder that I mainly use and delete the Administrator Account to get a fresh install that I can maintain properly without problems like I just quoted.
This is for my DA 533 MHz.
Thank you!
-Mike

How to Perform an Archive and Install
An Archive and Install will NOT erase your hard drive, but you must have sufficient free space for a second OS X installation which could be from 3-9 GBs depending upon the version of OS X and selected installation options. The free space requirement is over and above normal free space requirements which should be at least 6-10 GBs. Read all the linked references carefully before proceeding.
1. Be sure to use Disk Utility first to repair the disk before performing the Archive and Install.
Repairing the Hard Drive and Permissions
Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger.) After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported, then quit DU and return to the installer.
2. Do not proceed with an Archive and Install if DU reports errors it cannot fix. In that case use Disk Warrior and/or TechTool Pro to repair the hard drive. If neither can repair the drive, then you will have to erase the drive and reinstall from scratch.
3. Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When you reach the screen to select a destination drive click once on the destination drive then click on the Option button. Select the Archive and Install option. You have an option to preserve users and network preferences. Only select this option if you are sure you have no corrupted files in your user accounts. Otherwise leave this option unchecked. Click on the OK button and continue with the OS X Installation.
4. Upon completion of the Archive and Install you will have a Previous System Folder in the root directory. You should retain the PSF until you are sure you do not need to manually transfer any items from the PSF to your newly installed system.
5. After moving any items you want to keep from the PSF you should delete it. You can back it up if you prefer, but you must delete it from the hard drive.
6. You can now download a Combo Updater directly from Apple's download site to update your new system to the desired version as well as install any security or other updates. You can also do this using Software Update.

Similar Messages

  • Hard Drive and Disk Utility Failure on Macbook Pro

    Ok, so I've had this Macbook Pro since Sept. 2006 and I upgraded the operation system to Leopard about a year and a half ago. I've had no problems until now.
    A few days ago I did a software update for the OS, and didn't seem to have any issues. The next day when I booted up the computer, it was very slow in starting up. When it did start up, it only displayed the Macintosh HD and not my files, but a few minutes later everything else loaded.
    When I ran disk utility it just said that the hard drive needed to be repaired. The error was talking about a file on the server that was supposed to be numbered 1002 and instead was labeled 501 (?)
    Now my issues is, I can't find the Leopard disc, (i moved and I think I lost it?) and all I have is the original Tiger OS disc. I tried to reinstall the HD after backing up the files I needed onto my external. The Tiger OS disc will not work, it says there isn't enough space to be installed onto the computer. Also now whenever I turn on the computer the screen is grey with the apple logo, goes through the blue screen launch and just pops up the window that says "Mac OS can't be installed on your HD"
    So right now I am frustrated. If anyone has any advice, please let me have it. Am I completely out of luck or could Apple help me? I no longer have applecare btw, it expired this past October.

    !http://i46.tinypic.com/2nvn6f.gif!
    "I upgraded the operation system to Leopard about a year and a half ago."
    Your system info confirms you have Snow Leopard (10.6.2) installed.
    Leopard (10.5) & Snow Leopard (10.6) are 2 separate OS systems.
    You need your Snow Leopard DVD to repair the damage if that is the OS that is currently installed on your MBP.
    "When I ran disk utility it just said that the hard drive needed to be repaired."
    If SL is the DVD you cannot locate then you will need borrow a retail SL DVD & run the +"repair disc"+ setting or purchase one of the following to repair:
    DiskWarrior
    Highly recommended for *directory damage* repairs.
    TechTool Pro
    Multi-functional utility.
    Drive Genius Multi-functional utility.
    You will need to make your own decision on which to purchase. Read up on them on their websites because each does something a little different.
    You must use the versions that are compatible w/your OS system & keep the utilities updated to avoid damaging/harming/trashing your system.
    !http://i50.tinypic.com/izvwo1.gif!

  • Disk Utility - get errors and disk utility can not repair, even start ext.

    Hello
    I am using Mac OS X 10.5 on a MacBook Pro intel 2.4 Ghz Intel Core 2 Duo, 2 GB RAM, Intel and Boot Camp / Win XP installed.
    To check my user rights and repair the main HD I have installed 10.5 on my external 500 GB USB 2.0 HD. Started from it and started the disk utility trying to check and repair the Macintosh HD Partition (not win xp). I got following error messages:
    2007-12-01 10:47:12 +0100: „Festplatten-Dienstprogramm“ wurde gestartet.
    2007-12-01 10:47:20 +0100: Zugriffsrechte für „Macintosh HD“ reparieren
    2007-12-01 10:53:51 +0100: Warnung: Die SUID-Datei „usr/libexec/load_hdi“ wurde geändert und wird nicht repariert.
    2007-12-01 10:53:51 +0100: Warnung: Die SUID-Datei „System/Library/PrivateFrameworks/DiskManagement.framework/Versions/A/Resources /DiskManagementTool“ wurde geändert und wird nicht repariert.
    2007-12-01 10:53:51 +0100: Warnung: Die SUID-Datei „System/Library/PrivateFrameworks/DesktopServicesPriv.framework/Versions/A/Reso urces/Locum“ wurde geändert und wird nicht repariert.
    2007-12-01 10:53:52 +0100: Warnung: Die SUID-Datei „System/Library/PrivateFrameworks/Install.framework/Versions/A/Resources/runner “ wurde geändert und wird nicht repariert.
    2007-12-01 10:53:55 +0100: Die Zugriffssteuerungsliste wurde gefunden, jedoch nicht für „private/var/root/Library/Preferences“ erwartet.
    2007-12-01 10:53:55 +0100: Die Zugriffssteuerungsliste wurde gefunden, jedoch nicht für „private/var/root/Library“ erwartet.
    2007-12-01 10:53:55 +0100: Die Zugriffssteuerungsliste wurde gefunden, jedoch nicht für „private/var/root“ erwartet.
    2007-12-01 10:53:57 +0100: Warnung: Die SUID-Datei „System/Library/PrivateFrameworks/Admin.framework/Versions/A/Resources/readconf ig“ wurde geändert und wird nicht repariert.
    2007-12-01 10:53:57 +0100: Warnung: Die SUID-Datei „System/Library/PrivateFrameworks/Admin.framework/Versions/A/Resources/writecon fig“ wurde geändert und wird nicht repariert.
    2007-12-01 10:54:00 +0100: Warnung: Die SUID-Datei „usr/libexec/authopen“ wurde geändert und wird nicht repariert.
    2007-12-01 10:54:01 +0100: Die Zugriffssteuerungsliste wurde gefunden, jedoch nicht für „System/Library/CoreServices/Finder.app/Contents/Resources/CannedSearches/All PDF Documents.cannedSearch/Resources/version.plist“ erwartet.
    2007-12-01 10:54:01 +0100: Warnung: Die SUID-Datei „System/Library/CoreServices/Finder.app/Contents/Resources/OwnerGroupTool“ wurde geändert und wird nicht repariert.
    2007-12-01 10:56:07 +0100: Die Zugriffssteuerungsliste wurde gefunden, jedoch nicht für „Applications“ erwartet.
    2007-12-01 10:56:07 +0100: Die Zugriffssteuerungsliste wurde gefunden, jedoch nicht für „Library“ erwartet.
    2007-12-01 10:56:11 +0100:
    2007-12-01 10:56:11 +0100: Reparatur der Zugriffsrechte abgeschlossen
    2007-12-01 10:56:11 +0100:
    2007-12-01 10:56:11 +0100:
    Translation: wurde geändert und wird nicht repariert. = was changed but was not repaired.
    Because it can not repair the errors I have started "repair disk". It says "can not unmount Macintosh HD". Even if I have started from the external disk?
    So I get my install CD (Mac OS X 10.5) and started from that. I got the same errors with that disk utility.
    Can someone tell me, if this are "right" errors or do I have to try more to repair this errors? My computer is running fine.
    I am a bit irritated now.
    Best regards
    arjello
    Message was edited by: arjello
    Message was edited by: arjello

    Way back in Jaguar Disk Utility would pop up dozens of "advisory" messages of no interest nor meaning to anyone except possibly some programmers. This needlessly alarmed regular users. The same thing is happening again in Leopard. The SUID messages are not meaningful nor are they errors, in effect they are announcements that some list being consulted by the utility says one thing, the actual files say something else, Disk Utility is going to assume there is a reason for actual setting and not going to change it, but you (it's kind of assuming you are the programmer) should know this. If the "Die Zugriffssteuerungsliste" is German for ACL (Access Control List) it is the same deal: an ACL was found, but no one told Disk Utility there was suppose to be one.
    If the messages bother you download the whole 110MB 10.5.1 update and run it. It quiets down the output for all the SUID statements save one. Might even shut down the ACL advisories--don't know because I haven't bothered to download 110MBs of updater, I just ran the patch update.
    Francine
    Francine
    Schwieder

  • Disk read error, and Disk Utility won't open

    Have a PowerMac G4 dual 800mhz, with two hard drives. Mac OS X 10.3.9 is installed on HD1. I use HD2 for miscellaneous files.
    Using the Azureus bittorrent client, I'm getting "Error: Disk read error - Input/output error, read fails" in the Status column when trying to download something to HD2.
    However, I'm able to upload files from HD2 for other users, and I'm also able to play video files that are stored on HD2 without problem.
    The real issue is that when I went to see if I could fix anything by opening Disk Utility, it won't open. It goes into an immediate state of Not Responding. It won't listen to me when I tell it to Force Quit... I have to wait a long time, or restart the computer, to get it to stop showing up in the dock.
    Any advice would be appreciated.

    To repair a startup volume you must do the following:
    Repairing the Hard Drive and Permissions
    Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. Then select Disk Utility from the Installer menu (Utilities menu for Tiger.) After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer. Now shutdown the computer for a couple of minutes and then restart normally.
    If DU reports errors it cannot fix, then you will need Disk Warrior (4.0 for Tiger) and/or TechTool Pro (4.5.2 for Tiger) to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
    Why reward points?(Quoted from Discussions Terms of Use.)
    The reward system helps to increase community participation. When a community member gives you (or another member) a reward for providing helpful advice or a solution to their question, your accumulated points will increase your status level within the community.
    Members may reward you with 5 points if they deem that your reply is helpful and 10 points if you post a solution to their issue. Likewise, when you mark a reply as Helpful or Solved in your own created topic, you will be awarding the respondent with the same point values.

  • Time Machine Error and Disk Utility?

    I backup 3 Macs to our TC. Last night, my MacBook started having problems backing up to the TC. Several times it has attempted to backup, but it fails with this message:
    "The problem may be temporary. Try again later to back up. If the problem persists, use Disk Utility to repair your backup disk."
    When I try to use DU to repair as suggested, the drive does not mount, whether or not I connect to it in the Finder or not. Airport Utility reports no problems with the TC and the other two computers are happily backing up hourly to it. There is 500 GB of space left on it.
    When I open the TC drive, I see two sparsebundles for ths laptop, only one for each of the other computers. It appears to me that there is something wrong with the sparsebundle/s for this computer only. Can I simply drag those to the trash, connect via firewire to TC, and start fresh? I really don't want to have to erase the whole TC and redo the other computers.
    Is there another solution I am missing?
    Thanks for any help.
    Kathy

    Kathy Cardoza2 wrote:
    Can I simply drag those to the trash, connect via firewire to TC, and start fresh?
    That should work, except for the item about "connect via firewire", as a Time Capsule has no FireWire port. Could you have meant Ethernet? That should speed up the initial backup significantly.

  • Disk Management Tool error in Disk Utility

    Update: (first, reviewing problem that I and others have been having, including on 10.4.x systems):
    When I attempt to repair permissions on my HD with Disk Utility, I get this specific error message: "Disk Utility internal error -- Disk Utility has lost its connection with the Disk Management Tool and cannot continue. Please quit and relaunch Disk Utility" and the repair-permissions will not proceed. It fails to get the proper "correct" permissions info for that drive to allow the repair. The error log points to a file in the Library called "DiskManagementToll" The path is ~/System/Library/PrivateFrameworks/DiskManagement.framework/Resources/DiskManag ementTool)
    This problem is appearing in many forums here and elsewhere, including 10.4.x systems (like mine) and persists in a few after deleting suggested files. Is there a sophisticated solution that addresses the problem through the DiskManagementTool file by replacing some values or replacing the file from a backup vis SUDO or Root?
    Previous posts have focused on Macs running 10.3.x and with iTunes 6.0x installed. Not here, so the problem is more general. None of the "delete iTunes / plists / Chess.app" suggested fixes have worked for me. Also tried running DU from my Tiger install disk; no luck! -- still fails when it tries to determine the correct permissions.
    The "DiskManagementTool" file apparently either stores the correct file permissions or handles reading them from the receipts in the Library. If I understand things right, Disk Utility is actually a (user)-permissioned graphic front end, while DiskManagementTool is a Root-user-level tool that actually does the heavy lifting. Can I replace -- and any benefit to that -- or rewrite it with proper access?
    There is a complete crash log report in Crash Reporter, by the way. Anyone want the text, and would it help figure out what's happening?
    I've tried the suggested deletion of iTunes 6.0.2 or Chess.app and their plists (these and other steps were suggested on MacFixIt at http://www.macfixit.com/article.php?story=20060111090035797 the advice is, basically, to delete iTunes 6.0.2 and/or Chess.app and related plist files.) As I said, no luck!
    Everyone that I talk to says it MUST be the fault of some other 3rd-party disk utility software.
    For what it's worth, I HAVE run Disk Warrior -- and, the drive that's having the problem is a recent reinstall from a backup using Carbon Copy Cloner. The original disk is NOT having such a problem, only the hard drive on my iBook after the reinstall. Don't know if that gives any clues (or to how the link gets somehow disengaged between Disk Utility and the Disk Management Tool file / software).
    Any thoughts on that? What about replacing the Disk Management Tool file in the Library or forcing some kind of re-link to it? some Unix guru MUST know a fix!
    Obviously, the big worry for me is that I can't update my System to 10.4.5 or anything else without repairing permissions first. This IS a big deal. And others are having the same problem. Help?!?
    New 2 GHz dual g5 , Dual g4, & iBook G4 (recent) Mac OS X (10.4.4)

    A system problem was involved that became, briefly, a "known issue" that was solved in the next minor update. Solved, anyway, by the advice given by the last poster. Thanks! SJ

  • TS2570 Question re: "Start from your Mac OS X Install disc; use Disk Utility"

    I've worked my way through the step-by-step trouble shooting in the TS2570 article up to "Start from your Mac OS X Install disc; use Disk Utility". So far, every step results in the same outcome - my formerly trusty 2007 Intel duo core iMac (24") will not start up, freezing on a grey screen with a blinking question mark on a folder. I don't completely understand this next step. I have both a Leopard and a Snow Leopard disc. I'm not positive whether these were for the iMac, or my old Macbook Pro. I assume this makes a difference.

    Question (?) Mark, Blinking Folder, or Gray Screen at Startup
    These are related but not identical issues. Their causes are outlined in Intel-based Mac- Startup sequence and error codes, symbols. Solutions may be found in:
    A flashing question mark appears when you start your Mac
    A flashing question mark or globe appears when you start your Mac
    Mac OS X- Gray screen appears during startup
    In most cases the problems may be caused by one or more of these:
    a. Problem with the computer's PRAM - See Resetting your Mac's PRAM and NVRAM.
    b. Boot drive's directory has been corrupted - Repair with Disk Utility.
    c. Critical system files are damaged or deleted - Reinstall OS X.
    d. The disk drive is physically non-functional - Replace the hard drive.
    Note that the information I have provided is what Apple recommends, If other users suggest different solutions than found here, then be sure what they recommend does not impact on your warranty, if any, or ability to get continuing Apple service.
    Please don't start removing drives or changing cables unless you know what you are doing and have exhausted other non-invasive alternatives outlined here. If you perform any work yourself that is unapproved by Apple, then you will void any warranty you may have and lose all further Apple Support.
    Repair the Hard Drive and Permissions
    Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list.  In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive.  If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
    If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
    The main difference if you are using Lion or Mountain Lion is that you must first boot from the Recovery HD. Simply boot from the Recovery HD to perform the above.
    Reinstall Snow Leopard Without Erasing The drive
    1. Repair the Hard Drive and Permissions
    Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list.  In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive.  If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
    If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
    2. Reinstall Snow Leopard
    If the drive is OK then quit DU and return to the installer.  Proceed with reinstalling OS X.  Note that the Snow Leopard installer will not erase your drive or disturb your files.  After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
    Download and install Mac OS X 10.6.8 Update Combo v1.1.
    Reinstalling Lion/Mountain Lion Without Erasing The Drive
    Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
    Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
    When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list.  In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive.  If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
    Reinstall Lion/Mountain Lion: Select Reinstall Lion/Mountain Lion and click on the Continue button.
    Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.

  • Reported Fatal Hardware Error to Disk Utility

    I see the following message in my Power Book G4 Disk Utility:
    "This drive has Reported Fatal Hardware Error to Disk Utility. If drive has not failed completely, back up as much data as you can and then replace it with a new drive."
    I already made a back up my Home folder to my external HD. The install disk utility reports the same and has grey the repair uptions.
    The spinning beachball appears constantly when using Safari and iTunes. What should I do?

    If your Mac is no longer under the standard 1-yr warranty period or under the 3-yr extended warranty if you purchased the AppleCare extended warranty for your PB, you need to purchase a new internal hard drive that is compatible with your Mac model. This is something you can install yourself or take your Mac to an Apple authorized repair facility to purchase and have a new internal hard drive installed.
    The repair facility should include re-installing whichever OX version and all software that was pre-installed and shipped with this Mac when purchased new. If this wasn't Tiger and you purchased a Tiger retail install package, you can re-install the Tiger upgrade yourself and then replace all data from your backup on the new hard drive.

  • Errors in Disk Utility

    Hello. I was wondering for some opinions. i was having some problems with permission errors in disk utility so they wanted me to erase and install with a new disc set. So I completely erased the disc and reinstalled just the software on the mac os x discs. Now, after running typical software update and now I have 492 pages of permission errors. I ran it three times so far and it is still coming up with 492 errors on it.
    What could be causing this?

    Hi,
    *"i was having some problems with permission errors in disk utility so they wanted me to erase and install with a new disc set."*
    Who is they? Apple?
    You have 492 pages of permissions messages or 492 messages?
    It won't do any good to keep running it. Go here for information on permissions you can ignore. http://support.apple.com/kb/TS1448
    Carolyn

  • Drive has reported a fatal error to Disk Utility, HELP ME PLEASE!!!

    I'm a little worried my Macbook Pro has become an overpriced paperweight.
    Here's what happened:
    I had a spare 512MB RAM, which was taken out of my 24" iMac Intel Core 2 Duo when I replced it with a 1GB RAM and, after checking several sources on the web, successfully installed the extra RAM in the MBP.
    I restarted the MBP and the new RAM was registered after checking in About this Mac. I then began using the MBP as normal and wrote and saved a Word document. I clicked on the email and Safari icons in the dock and they just kept bouncing in the dock without launching. Pressed Power button - nothing. Took out the battery and replaced it after 30secs and pressed power button. All I got was the grey screen with the Apple logo and the winding circle which stayed like that for 20 minutes.
    First reaction was to remove the RAM and restart. Same endless grey screen and winding circle.
    Rebooted from CD, checked disk and repaired and said everything was OK. Restarted without CD still nothing.
    Tried Archive and Install and came back with an error during installation.
    Tried Erase and Install - same error.
    Tried to select startup disk and it no longer could find my HD yet Disk Utility could find it and told me everything was OK. Tried resetting PRAM nothing.
    Tried to erase the HD and nothing happened. Erasing a HD takes some time, but everytime I hit erase 10 seconds later it was back to the same point where I began
    Next tried to create one single partition and struck the message Drive has reported a fatal hardware error to disk utility. Even the lettering for the main drive is now in red.
    Do I need to replace the hard drive altogether or is there a solution to this problem. Was it the RAM that brought me undone or was that just a coincidence?
    PLEASE HELP ME!!!

    make sure that you haven't used it yet as RAM can only be used in one machine, not transferred to another one (like you did).
    Sorry, but that's completely untrue, and I don't know where you might have read or heard such a fallacy. RAM has no registration that even tells a system that it's been used, much less a key that would make it work only in one system. As long as the RAM is properly compatible and precautions are taken not to shock a system with static electricity while removing or inserting the component or causing mechanical damage, a RAM module can be swapped between systems as often as desired.

  • Problems running Software Update and Disk Utility

    I had automatic updating turned on in the Software Updates control panel, so I believe the system tried to apply the 10.4.6 automatically and somehow failed.
    Ever since, when I try to run Software Update it hangs while trying to connect to the internet to get the list of available updates. I tried downloading the installer directly from Apple, but when I try to select a volume on which to install the update, it doesn't list my hard drive.
    Finally, when trying to run the Disk Utility, I get an error about how the Disk Utility cannot be started because a background process is not running. I have to Force Quit to exit out of the Utility.
    I was able to boot off the Mac OS X 10.4 installation DVD at which point I repaired the permissions and repaired the disk. However, upon restart the same problems remain.
    I've seen several other people post about this issue; has anyone found a resolution OTHER than doing an Archive and Install (which I don't want to do if I don't have to?)
    Thanks so much for help that anyone can provide!
    iBook G4   Mac OS X (10.4.5)  

    Create a new admin account with Apple menu -> System Preferences -> Accounts and see if the issue duplicates itself logging into that account. That will say if the issue systemwide, or just localized to the a bad user cache file. If the issue persists in the new user, you can try looking in the System -> Library and Library -> Cache, Applications Support, and ByHost folders for cache files relating to Software Update and Disk Utility. Once you find them, carefully extract them to comparable folders on your desktop you create (i.e. name one systemlibrarycache) so you know where you go them from, and restart your Mac. If the issues go away after two restarts then it is just one set of bad cache files. If the issues return after two restarts, you have something generating bad cache files which needs a more system wide repair tool.

  • Endless errors on disk utility

    My 2nd internal hard drive in 2.5 years just died on my iMac G5. Apple is coming on-site to fix. During the 1st hard drive death, I installed the operating system on an external drive and was able to work from that drive. I assume this was legal since I was discussing all these things with AppleCare as the int harddrive died (over the course of a week of AppleCare calls). Doing this allowed me to save a substantial amt of data. Since then I have used this drive as a backup drive, rathern than as an operating system.
    Now, I'm trying the same thing with the 2nd internal hard drive death. After booting up to the external drive, the first thing I did was upgrade from 10.4 to 10.4.8. I restarted the computer using the exteral drive. The Mac OSX setup assistant wouldn't connect. I tried to disconnect and it wouldn't disconnect, either. I Force Quitted out of the setup assistant. The 2nd thing I did was run disk utility and verify permissions. It said I had no valid packages. I copied BaseSystem.pkg and Essentials.pkg into the Library. Now disk utility gives me absolutely endless errors, all of them "User differs on..." followed by "Group differs on..."
    Since this is mainly a backup disk, all my files are under ExtHD/ rather than a user. I don't know anything about packages--I read the above on an earlier post and it got rid of the "No valid packages" error on Disk Utility when I first ran it. I don't know anything about receipts, etc. About the only thing I know is that I have two libraries, one for the main hard drive and one for the user.
    I'd like to keep this external drive as a bootable system. I want to be able to run Disk Utility to clean it up. Any suggestions?
    iMac G5, MacBook   Mac OS X (10.4.8)  
    iMac G5, MacBook   Mac OS X (10.4.8)  

    So I can do an archive and install, and then when the fresh Tiger is on there, would I upgrade to 10.4.8 right then? Then I suppose I copy all my backed up files to the correct user directories?
    How much memory do I need on that hard drive to archive and install? I'm assuming it archives on the same hard disk. Does that mean I have to have less than 1/2 of the memory used, so it can back itself up, or does it erase old data as it archives, freeing up memory space?
    Thanks for your input!

  • Bios not install error and Raid Configuration not showing physcial HDD in Lenovo

    Is this a SATA hard drive by any chance?  Sounds like you have an Adaptec SCSI controller, but no hard drive attached to it.  Are you booting an install DVD of some sort?

    Bios not install error and Raid Configuration not showing physcial HDD in Lenovo RD 120 Server (New)
    updated bios still same error
    and at array configuration it is not showing any hard disk
    hard disk utility it is showing hard disk 
    we are trying to install OS with single hard disk in Lenovo RD 120 Server
    This topic first appeared in the Spiceworks Community

  • Safari, Mail and Disk Utility won't run unless Font Book is Open

    Recently Safari, Mail and Disk Utility would crash and spin and the "Application Not Responding" line would appear when I checked the program in the dock. After following a variety of tips from other Apple users, I finally got the programs to run. However, I started them while Font Book was open and now they only work when it remains open. I've been using Apple/Mac products since the beginning of time and have never seen anything like this. I've repaired permissions, throught out preferences, etc., etc. and can't resolve this problem. Please, someone, help me.

    Hello buhrow:
    That makes two of us that go back to the beginning of time and have never seen anything like that. Have you run the fontbook applications to eliminate duplicates and check for corrupt fonts? Offhand, I cannot understand why just having a program open would prevent other programs from crashing.
    If nothing else works, you might want to consider an archive and install (after backing up, of course):
    http://docs.info.apple.com/article.html?artnum=107120
    Barry
    Message was edited by: Barry Hemphill (spelling, no checker)

  • "Could not find RAID" error in Disk Utility

    Hello,
    I could really use some help as this problem is causing me lots of headaches. I have two 500GB MyBook hard-drives connected to my MacBook Pro via two USB's. I had them setup as a mirrored RAID, and they were working properly for quite sometime. However over the past few weeks I noticed they were always in a degraded state, and Disk Utility would always rebuild them. However after the rebuild they would still have the status of "Degraded" and the next time Disk Utility opened it would start the rebuilding process yet again.
    So I moved all the data on the drives to a backup, and I stopped the mirrored RAID. After erasing the data on the drives individually I attempted to setup the mirror again. However after the mirror had just about finished, and it was to the point of "bringing the RAID online" I always get an error that states "Creating RAID set failed", "Creating RAID set failed with the error: Could not find RAID.".
    I'm hoping someone smarter than myself in this area can lend me some time and assistance to solving this issue.
    Thanks,
    Paul

    Well. No one really came to my rescue with this question. Turned out to be a Finder issue. After reinstalling the operating system everything started working again with Disk Utility.
    Later,
    Paul

Maybe you are looking for