Intemittent dropouts connecting through NBN Australia Skyedge2 satellite modem, via Ethernet is fine, but Airport express wireless is unreliable!
Intermittent dropouts connecting to NBN Australia Skyedge2 satellite modem. Via Ethernet is fine, but Airport Express wireless is unreliable! In particular https and getting mail. This problem did not occur on previous Optus satellite AGBG satellite system. Is there a different mode required for AAE?
I continue to have the problem with dropouts to satellite internet via airport express. My isp has loaned me a Linksys (Cisco) E1200 wireless router which I have connected and it works flawlessly. Maybe my AEx is faulty?
Similar Messages
-
hi i got a mac mini but when i connect it to my smartax mt882 modem via ethernet it says device not connected can anyone solve this issue it work fine with the usb connection but the ethernet is giving me problems plz help
Hello, give this a try...
Make a New Location, Using network locations in Mac OS X ...
http://support.apple.com/kb/HT2712
10.5, 10.6, 10.7 & 10.8…
System Preferences>Network, top of window>Locations>Edit Locations, little plus icon, give it a name.
10.5.x/10.6.x/10.7.x/10.8.x instructions...
System Preferences>Network, click on the little gear at the bottom next to the + & - icons, (unlock lock first if locked), choose Set Service Order.
The interface that connects to the Internet should be dragged to the top of the list.
For 10.5/10.6/10.7/10.8, System Preferences>Network, unlock the lock if need be, highlight the Interface you use to connect to Internet, click on the advanced button, click on the DNS tab, click on the little plus icon, then add these numbers...
208.67.222.222
208.67.220.220
(There may be better or faster DNS numbers in your area, but these should be a good test).
Click OK. -
My wi-fi connection from my iPad via the Airport Express Base Station on my home computer worked just fine until yesterday morning. I have a Macintosh G5 with a satellite connection. I could not get an Internet connection. After using the Network Preferences and Aiport Express applications several times, then unplugging and replugging in the computer, satellite modem and Airport Express module, checking the satellite dish for any obstructions, and so on, the computer still wouldn't connect to the Internet. (The green light was on in the Airport Express module.) I called the satellite company technical support division last night. The tech couldn't find any problem with the satellite connection. When I plugged the satellite modem cord directly into the Ethernet outlet on my computer, I could pick up the Internet.
Today, the Airport Express module still has a green light but still doesn't connect to the Internet. The only thing I can think of is that lights went out for about 15 minutes yesterday morning. All of my electronics, except the Aiport Express Base Station, are on surge protectors. Why would the Airport Express module still have a green light if it was damaged by the electrical outage?
I bought the module in 2009. I have never had problems with Apple equipment before this. Is this base station fixable?
I would appreciate your suggestions.Hello everyone. I too have experienced the same problem Mary described starting on the same day she mentioned January 12. I have a G5 iMac, a G5 mini-mac, and a G4 laptop. They were all working fine but all have mostly the same problem now in that the G4 does not connect at all and the G5s connect once in a while after restarts but do not maintain the connection. In my case there was no power interruption. In fact, the G4 laptop was not even connected to the home power connection. My iPad2 and iPhone 4s wireless work fine and a wireless PC and Android tablet work fine as well. The G5 and G4 work fine on an ethernet connection. ISP tech support (AT&T u-Verse) was very generous with their time in trying to solve my problem although it was established early on that their connection and equipment was working fine and that the problem was with my computers. They walked me through a manual reset of all the particulars on IP addresses etc. so the problem was not related to that either. In the end ISP tech support concluded that the problem must lie with the Airport driver. For some reason it changes the IP addresses to an incorrect address so it cannot connect. Indeed when I tried the diagnostics on the G4 I got a window Pop-up that said an application had reset my settings. (In retrospect I seem to recall that I may have gotten that same message early on with the G5s but at that time I did not think much about it and went about trying to reset the settings but that process never concluded well) I think that the problem may be that there must have been an update of the Airport software that was not backward compatible with the G5 and older Macs. I mention all this for two reasons. First, perhaps someone out there who knows better than I do how to bring this to Apple's attention and perhaps they will address this. Second, I would be curious to know whether there is anyway one can return a configuration on Macs to some earlier time period (as you can on PCs) when everything worked and then leave it that way foregoing any subseqent upgrades or any subsequent apps?
-
Airport Time Capsule 3TB can't connect to modem via ethernet
Hi all,
Thanks in advance for any assistance on this issue ...
I am having extreme difficulty in connecting my Airport TC to my modem via ethernet. Ideally, I want to use it to extend the range of my wifi, as well as back up my machines.
I can't get the AP TC to add on to an existing network in initial set up as , even though the option is available, the Airport Utility (6.3.2) doesn't seem to keep it selected, and wants to create a new network.
When I create the new network, my internet connection drops out, even though the modem indicates that it is connected. I then edit the internet connection in AU by telling it to extend the existing network (add in the SSID etc) which picks up the internet connection again, but then the Airport TC drops out, and all I get is a blinking amber light and a message saying no configured Airport Base Stations detected, continuing to search.
I have no doubt that it is something I am or am not doing. I have soft, hard and Factory reset the TC, reset the modem, changed cables, pretty much everything my tiny brain can think of.
I have looked through the support pages and follwed thier advice, with no luck.
Help please.I can't get the AP TC to add on to an existing network in initial set up as , even though the option is available, the Airport Utility (6.3.2) doesn't seem to keep it selected, and wants to create a new network.
"Add" would be used for a wireless connection....and you indicate that you are using Ethernet to connect the existing modem/router and Time Capsule together....so the correct setup would be to create a new network using the exact same wireless network name and password as your existing network.
Connect an Ethernet cable from one of the LAN <--> ports on the current modem/router to the WAN "O" port on the Time Capsule.
Here, I am assuming that the TC will be located at least a room or two away from your main wireless router. If it is located any closer, there will likely be wireless interference issues between the two routers. The wired connection between the modem/router and Time Capsule must be maintained.
AirPort Utility will suggest a setup that looks somewhat like this.....except you will see a Time Capsule instead of an AirPort Express as illustrated below:
Network Name would be the name of your existing wireless networik
Base Station Name is a device name that you want to call your Time Capsule
Password is the wireless password of your existing wireless network
Verify confirms that password
Click Next and the setup utility will auto configure things for you in a minute or two
When you see the message indicating Setup Complete, click Done and you should have a green light on the TC. -
Configuring the time capsule airport wlan function as "connect to wlan", the time capsule gets a correct IP adress from the other wlans IP range, but does not assign this to the ethernet ports. With Airport express it worked, the single Ethernet port got the IP Parameters passed through!
My setup is a Vodafon Esaybox connected to ISP. Time Capsule is not able to extend the wlan of the easybox, neither airport express can do.
Only the option "connect to wlan" is succesful.
With airport express I was able to connect my Sony Bravia TV to the lan via ethernet to stream pictures, the TV set got an IP adress from the easybox.
With the time capsule the easybox dosn't find devices connected to the ethernet ports to submit IP adresses. The TV set get another IP adress (169.xxx.x.x.) in subnet mask 255.255.0.0 and I don not now where from.
My notebook is a MacBook pro.
Any idea????
Thank a lot in advance!
Kind regards
IngoNeverthe less, could there be the chance, that this feature could be implemnented with an firmware update?
That would appear to be a question for Apple to answer. You can make suggestions to Apple here:
Apple - AirPort Extreme - Feedback
If the AirPort Extreme and Time Capsule are configured to "extend a wireless network" they will provide additional wireless coverage....and...the Ethernet ports are enabled in this type of setup.
The "catch" here is that you must have an Apple router providing the network to be extended. -
My MacBook Pro will not connect to my home wifi but will connect everywhere else. My other Apple devices (I-pad, I-touch, another MacBook Pro) connect to the router without problems. It was working fine but all of a sudden stopped working.Thanks!
try this.
get back into your router's settings and start deleting devices that are not connected to your router.
you can also delete the ones that are connected - they'll connect again.
on the DHCP side of it, increase the amount of users that can connect/log in to your router.
see if that sorts it out for you.
good luck. -
I have connected my time capsule to motorola SG6580 modem via ethernet. I have a wireless network on the motorola and a wireless network from the time capsule. I get duplicate IPs error messages (no connection) sometimes when trying to connect devices to the wireless network. How do I fix? Sometimes devices cannot connect to the network because of conflicting IPs. I look on the Motorola and every device has a unique IP assigned but occasionally a device has taken the IP of another device. I have been writing down all the devices and the IPs they have been using. It happens more with PCs than Macs, ipads or iPhones.
If the Time Capsule is set up correctly in bridge mode, then it is the responsibility of the Motorola modem/router to provide the correct IP address assignments for all devices on the network.
Check to insure that the Time Capsule is correctly set up to operate in bridge mode as follows:
On your Mac, open AirPort Utility
Finder > Applications > Utilities > AirPort Utility
Click on the Time Capsule icon, then click Edit in the smaller window that appears
Click the Network tab at the top of the next window
Insure that the setting for Router Mode is configured to read "Off (Bridge Mode)"
Once you have confirmed that the Time Capsule is configured correctly, everything else is the responsibility of the Motorola modem/router as far as network routing and IP address assignments for devices.
If you continue to have IP address issues, then you should contact the Internet Service Provider (ISP) that provided the Motorola device to you and ask them to fix the issue. -
Airport express wireless connection freezes SSH connection - any fixes?
airport express wireless connection freezes SSH connection - any fixes?
so i am using an airport express and remotely access computers/servers via SSH. port forwarding is set up and the computer has a fixed local IP address.
if i continue to issue command in the shell, then the connection persists. however, if i leave it idle for some amount of time more than a half an hour, both terminal and xterm (X11) freeze for a considerable amount of time. then they time out and return to a active shell on the local computer.
i have since determined that this does not occur if i am using a direct (built-in) ethernet connection.
is this problem fixable? are there settings in airport admin utility that can be changed to prevent this from occuring?
any advice or pointers would be tremendously appreciated
stefanoshi bill,
thank you for the suggestion. i added the lines to my .ssh/config file and so far it seems to have solved the problem.
i'll evaluate it over the next few days and post back if i notice any problems. it seems to achieve what i was thinking at least conceptually. to somehow, while idle, send something to ensure the connection stays alive.
many thanks for the solution. it's been a nagging issue and it's great to be likely rid of it.
stefanos
Powerbook G4 & iMac G5 :: Mac OS X (10.4.9) -
I can't connect Airport Express wirelessly to network so that AirTunes and internet are available simultaneously. My old AE allowed this but can't make the new one work that way.
In your instructions, you say to use the same encryption type as the router has set up. well, I am using the WEP 64 bit encryption and the Airport Utility does not have this...it has 40 bit. Is this a problem, or do I have to be using a the same type of encrytion ?
WEP is available in either 40 or 104-bit, but is usually "advertised" as either 64- or 128-bit respectively. For example, 64-bit WEP uses a 40 bit key (also known as WEP-40), which is concatenated with a 24-bit initialization vector (IV) to form the 64-bit RC4 traffic key. So, WEP 64 on the Linksys & 40-bit is equivalent.
What concerns me more is the loss of bandwidth performance you are experiencing when connecting the AX. When the AX is configured as a wireless client it is acting just like any other wireless devices (computer, laptop, printer, etc.) and not like another router. This should cause little or no bandwidth loss. True the more secure the wireless encryption used WPA2 vs. WEP, the more overhead is required for security, but the differences you are seeing seem excessive.
It is very possible that you may have some form of Wi-Fi interference in the immediate area that is preventing your Linksys from providing a good clean signal.
I suggest you perform a simple site survey, using utilities like the following to determine potential areas of interference, and then, try to either eliminate or significantly reduce them where possible:
For Macs:
o MacStumbler
o iStumbler, or
For PCs:
o NetStumbler -
Cannot connect Airport express wireless
Hello, cannot connect airport express wireless to linksys router. Connected now with ethernet cable but cannot figure wireless connection. My laptop cannot find the express while preforming setup scan, yet I'm connected to it. I can connect with my iphone but not wirelessly. Any suggestions?
....I was then told over the phone that airport express will not connect to third party routers.
This is NOT correct.
The AirPort Express will connect to a wireless network if you know the following:
1) The name of the wireless network
2) The exact setting for wireless security that the network is using
3) The wireless network password
Most users know 1) and 3), but very few know the exact type of wireless security settings that their wireless router is using. The Express will not connect to the wireless network unless it receives all of the information listed above.
So...we will assume that you know the name of the wireless network and the password for the network.
Do you know the exact type of wireless security setting that your wireless router is using? If not, the Express will not connect.
You may need to check the setup of your wireless router....or if the router was supplied to you by an Internet Service Provider, they may be able to tell you what type of wireless security setting is being used.
Post back when you have this info and we will proceed. There are still no guarantees that the Express will connect....but at least there may be a chance. -
AirPort Express wireless connection, when I surf the news sites so I linked to **** pages. And must close the window. If I use my iPhone with Internet sharing the same computer, then I have no problem.
I believe that it is in AirPort Express, and would have to clean it. How do you do that?You need to use the Express in router mode.. I think you are trying to use it in bridge mode.. but you need to give us a lot more details.. screenshots might help more than anything.
-
Airport Express wireless network works fine, but won't connect to Internet
I had a power outage and since then my Airport Express doesn't connect to the Internet although everything else seems to work. I can see the AE just fine in the Airport Utility. My computer connects to the wireless network provided via the AE, so does my iPhone, so does my wireless printer, and I can print wirelessly from the computer to the printer, so the AE's wireless networking is working. If I directly connect my computer to the ethernet connection that I use for the AE, it connects to the Internet, so I have wired connectivity to the Internet. But somehow, I can't get to the Internet using the wireless network of the AE. Any suggestions on what I should try next?
Hi there,
Try to reset your Airport Express (AX), y pressing the little dot on the back of device. Keep pressed for some seconds until it flashes. Start then your Airport Utility and go through the setup process again. This will reset your whole wireless network. This may work for you. Good luck. -
I currently have an Airport Extreme Base Station connected to my DSL router by Ethernet. Because I have a long, sprawling home, I have 3 Airport Expresses configured to "Extend the Wireless Network" I've established. Because of my home environment--thick walls encompassaing wire mesh, sprawling rooms, etc., it is hard to maintain a continuously-strong, stable WiFi signal. I've been told that I can create a much more stable network by connecting the Express units to the AEBS via Ethernet cable. Since my home is already wired for Ethernet, I'm considering making this change. If I proceed to establish the Ethernet connections, how do I then set up Airport Utility to accomodate this switch from a Wireless-based WiFi network to an Ethernet-based WiFi network?
Thanks in advance for any help.
PhyllisI don't see anyplace in the Utility to designate HOW the Express units are connected, only how they relate on the network to the Extreme,
As I mentioned in the previous post, when you click the Internet icon in AirPort Utility:
Connect Using = Ethernet (This tells each Express to connect to the Extreme using the ethernet connection)
Connection Sharing = Off (Bridge Mode) (This setting allows your AirPort Extreme to function as the "main" router on the network, as it must for the setup to work correctly.
You do not need to configure anything differently on the AirPort Extreme (as long as it is working correctly now) to connect the AirPort Express devices.
The only other question I have is the following: I'm currently already using one of the Ethernet ports on the back of the Extreme-- for my husband's iMac. I really don't think he gains much in performance over how the iMac would run through wifi, so I could disconnect the iMac. If you think the iMac would do better to stay on the Ethernet connection, should I use a switch/splitter to add an extra connection?
Since each AirPort Express must connect using ethernet, you will need to use the 3 LAN <-> ports on the AirPort Extreme for the AirPort Express devices.
I would suggest that you try connecting the iMac using wireless to see if that will work. If the wireless connection is not satisfactory, then you can add a 5 port ethernet switch to one of the LAN ports on the Extreme and then plug all the devices connecting using ethernet....the iMac and the 3 AirPort Express devices...into the remaining 4 ports on the switch. That will leave you with 2 open ports on the AirPort Extreme for any future devices that may need to connect.
When you test out the system, here is a trick to find out which device your computer is actually connecting to at any given time as it "roams" around the house.
When you have AirPort Utility open to configure each AirPort Express, jot down the AirPort ID for each Express. You can do the same for the AirPort Extreme.
As you move around with your laptop, hold down the option key on your Mac keyboard while you click on the fan shaped AirPort icon at the top of the screen. Look for the BSSID. That is the AirPort ID of the device that the laptop is connected to at that time. it should also be the ID of the closest AirPort Express (or AirPort Extreme if the laptop is close to the Extreme at the time).
Let us know how things are working when everything is up and running. -
Since installing Airport Express wireless connection to other devices keeps being dropped
Our home network consists of my MacBook Pro 15", my wife's quite old Compaq notebook, an Apple TV, and recently, an Airport Express.
The router is one that was provided by our ISP, Alice/O2 in Germany. I think it is made by Siemens but its model name is Alice IAD 4421 WLAN (in case anyone in Germany is reading this.)
My MacBook connects to the WiFi broadcast perfectly every time, as did my wife's Windows laptop until recently. Between our two machines there was a total of one single occasion where the signal dropped, and a restart of the router got it back up and runnning.
The Apple TV was set up without any problems at all, the wireless connection dropped out once over the space of 6 weeks.
About 5 days ago, I bought and installed an Airport Express which has so far served the sole function of providing Airplay to 2.0 speakers in the kitchen, so I just selected 'join network' when setting it up in Airport Utility.
Since it was installed, video playing over Airplay to the Apple TV keeps stopping, with the message 'Apple TV is not connected to the internet', the AE itself suffers from dropouts in audio, (the LED has always stayed solid green) and my wifes notebook can only join the network after she has restarted it.
A restart of the router helps for about an hour, but the problems keep recurring.
Does anyone have any idea of any changes I can make to the AE settings, as it seems to be the cause of the dodgy connections to the other devices?Hello mathias1711. Welcome to the Apple Discussions!
Let's double-check your AirPort Express Base Station's (AX) settings for streaming iTunes ...
Perform a "factory default" reset of the AX
o (ref: http://docs.info.apple.com/article.html?artnum=108044)
To set up AirTunes on the AX, either connect to the AX's wireless network or temporarily connect your computer directly (using an Ethernet cable) to the Ethernet port of the AX, and then, use the AirPort Admin Utility to check these settings:
AirPort tab
o Base Station Name: <whatever you wish or use the default>
o Wireless Mode: Join an Existing Wireless Network (Wireless Client)
o Wireless Network: <select the existing wireless network>
Music tab
o Enable AirTunes on this base station (checked)
o Enable AirTunes over the Ethernet port (optional)
o iTunes Speaker Name: <whatever you wish>
o iTunes Speaker Password (optional)
In iTunes:
iTunes > Preferences... > Advanced > General
o Look for remote speakers connected with AirTunes (checked) -
Connect to internet via airport extreme via ethernet cable and no airport c
I just bought a MacBook with Airport Extreme, got it set up today and it works great, got online, etc. However, I have an iMac with no airport card. I can't figure out how to get both computers hooked up on the internet at the same time. The MacBook works only when the ethernet cable in in the LAN slot on the Extreme but won't work through the WAN slot. I have tried hooking up both ethernet cables into the Extreme, just the iMac, and nothing works. I don't need to connect wirelessly through the iMac so I don't want to buy an Airport card if I don't need one. I just don't want to plug and unplug the ethernet cable everytime I want to use the MacBook or the iMac. My modem from Verizon only has one ethernet slot. Any ideas?
I just bought a MacBook with Airport Extreme, got it
set up today and it works great, got online, etc.
However, I have an iMac with no airport card. I
can't figure out how to get both computers hooked up
on the internet at the same time. The MacBook works
only when the ethernet cable in in the LAN slot on
the Extreme but won't work through the WAN slot. I
have tried hooking up both ethernet cables into the
Extreme, just the iMac, and nothing works. I don't
need to connect wirelessly through the iMac so I
don't want to buy an Airport card if I don't need
one. I just don't want to plug and unplug the
ethernet cable everytime I want to use the MacBook
or the iMac. My modem from Verizon only has one
ethernet slot. Any ideas?
You mean Airport Extreme Base station?
Here's what you need to do:
1. Disconnect your Verizon Modem & Airport Extreme
2. Connect the ethernet cable from the Verizon modem to the WAN of the AE
3. Connect another ethernet cable from the LAN port of the AE to your iMac
4. Turn on Verizon Modem
5. Once all lights on the modem have turned on, turn on the Airport Extreme
6. On your iMac click on Applications --> Utilities --> Airport Admin Utility
7. Setup a Wireless network using this or the Airport Setup Assistant, located in the same Utility folder.
8. After you have created the wireless network, connect to it on your macbook
If for some strange reason you still can't figure it out, refer to the product manual or check:
http://docs.info.apple.com/article.html?artnum=106858
Maybe you are looking for
-
Hi I had my iTunes library on an external hard drive which has crashed. The data is unrecoverable. I've now bought a new laptop and I want to rebuild my iTunes library. I found a set of backup discs I created back in 2010 and although they don't repr
-
hi friends i need help on classical reports, sold-party, material sales and distrubitutation channel ,division, incoming orders,order number,invoice ,credit, i need sub totals and final total of invoice and each customer should display in new page .
-
I cant install iWork9.1Update? It keeps telling me ¨An eligible Keynote application was not found in the location /Applications/iWork '09.¨? I have OS X Version 10.6.8 Thank you very much for help
-
Has anyone tried drawing on the iPad with a stylus?
I have tried the Jukestyle iPad stylus to draw signatures on the iPad. Has anyone else tried an iPad stylus to use for signatures on documents and contracts? Which ones do you prefer?
-
Can someone please help, i have installed the card and software and have connected an rf cable from the SKy box to the CATV input on the tv tuner. When i auto scan, i can't get any channels, what is the correct setup? Any help or suggestion appreciat