IOS EZVPN and VPN 3k using external groups

Hi folks , i was trying to configure IOS easyvpn with vpn
concentrator. i am using an external group which is configured on acs
server.the configuration for ios eazyvpn is
crypto isakmp policy 10
encr 3des
hash md5
authentication pre-share
group 2
crypto ipsec client ezvpn ezvpn_cfg
connect manual
group ezvpn key ezvpn
mode network-extension
peer x.x.x.x
interface FastEthernet0/0
ip address x.x.x.x x.x.x.x
crypto ipsec client ezvpn ezvpn_cfg inside
interface Serial0/0
no ip address
encapsulation frame-relay
interface Serial0/0.1 point-to-point
ip address x.x.x.x x.x.x.x
frame-relay interface-dlci 100
crypto ipsec client ezvpn ezvpn_cfg
I had configured the vpn concentrator with an external group eazyvpn.
i had configured the acs server with a user eazyvpn password
eazyvpn.the radius attributes configured for this user are
[3076\012] CVPN3000-IPSec-Sec-Association
ESP-3DES-MD5
[3076\013] CVPN3000-IPSec-Authentication
RADIUS
[3076\016] CVPN3000-IPSec-Allow-Passwd-Store
Allow
[3076\027] CVPN3000-IPSec-Split-Tunnel-List
split_tunnel_list
[3076\030] CVPN3000-IPSec-Tunnel-Type
Remote-Access
[3076\031] CVPN3000-IPSec-Mode-Config
On
[3076\034] CVPN3000-IPSec-Over-UDP
On
[3076\055] CVPN3000-IPSec-Split-Tunneling-Policy
Only tunnel networks in the list
[3076\064] CVPN3000-Allow-Network-Extension-Mode
Yes
now whenever i try to connect it says phase 2 failed.my quick mode is
unsuccesfull.
the error which comes on the router is below
12:19:43: %CRYPTO-6-IKMP_MODE_FAILURE: Processing of Quick mode failed with peer
at 172.31.9.2
ezvpn-router#show crypto ipsec client ezvpn
Easy VPN Remote Phase: 2
Tunnel name : ezvpn_cfg
Inside interface list: FastEthernet0/0,
Outside interface: Serial0/0.1
Current State: SS_OPEN
Last Event: SOCKET_READY
Split Tunnel List: 1
Address : 10.1.1.0
Mask : 255.255.255.0
Protocol : 0x0
Source Port: 0
Dest Port : 0
Logs for the vpn conc. is as
Group [ezvpn] User [cisco]
PHASE 1 COMPLETED
324 07/11/2007 22:36:23.980 SEV=5 IKE/35 RPT=6 x.x.x.x
Group [ezvpn] User [cisco]
Received remote IP Proxy Subnet data in ID Payload:
Address x.x.x.x, Mask x.x.x.x Protocol 0, Port 0
327 07/11/2007 22:36:23.980 SEV=5 IKE/34 RPT=10 x.x.x.x
Group [ezvpn] User [cisco]
Received local IP Proxy Subnet data in ID Payload:
Address 10.1.1.0, Mask 255.255.255.0, Protocol 0, Port 0
330 07/11/2007 22:36:23.980 SEV=5 IKE/66 RPT=10 172.31.235.93
Group [ezvpn] User [cisco]
IKE Remote Peer configured for SA: ESP-3DES-MD5
331 07/11/2007 22:36:23.990 SEV=5 IKE/75 RPT=10 x.x.x.x
Group [ezvpn] User [cisco]
Overriding Initiator's IPSec rekeying duration from 2147483 to 28800 seconds
333 07/11/2007 22:36:41.650 SEV=4 IKEDBG/97 RPT=4 x.x.x.x
Group [ezvpn] User [cisco]
QM FSM error (P2 struct &0x35e5aa4, mess id 0x91292e44)!
NOTE: the configuration works fine when i use CLIENT mode. IT fails
when i change to NEM

Refer to the document "Configuring the Cisco VPN 3000 Concentrator to a Cisco Router"
http://www.cisco.com/en/US/tech/tk583/tk372/technologies_configuration_example09186a008009482e.shtml

Similar Messages

TS3694 I tried to update my iphone 3gs from ios 5 to 6 but because of software crash and while restoring with ios 6 it is not activated. Now I degrade it in ios 4 and can not use any app. How can I update this iphone?

I tried to update my iphone 3gs from ios 5 to 6 but because of software crash and while restoring with ios 6 it is not activated. Now I degrade it in ios 4 and can not use any app. How can I update this iphone?

Downgrading the iOS is not supported, and likely has caused the problems you are experiencing.
You'll need to go elsewhere for support.

Why can´t I create projects and tasks into a External Group?

Why can´t I create projects and tasks into a External Group?

At this time, it's not possible to collaborate on a Project with External Contributors or add an Externally-Facing group to a Project. This is functionality that we we hope to add at some point in the future.

Starting and stopping timer using external inputs interfaced with labview

hello,
I have trouble finding how to start and stop the timer using external voltage or current pulse. we are interfacing a circuit to labview. so for that we need to count the time it takes between the two external voltages. We have to keep on comparing the voltages to some reference voltage. And when the external voltage crosses the reference voltage we have to start the timer and again we have to stop the timer using tha same logic. We need it for time calculation between the triggers.
hope you can help.

https://decibel.ni.com/content/docs/DOC-23334 is agood example to start. You need to modify it to include stop trigger.

Macbook Chirps and clicks when using external monitor

My mid 2010 Macbook Pro makes chirping and clicking noises from the hard drive however it only happens when I have my external monitor hooked up. Any one have any idea why? It is different from the Motion sensor click. I've found all over the net that others are experiancing this issue (not connected to external monitor) however haven't I haven't seen a conclusion. Any ideas?
Thanks
Here is a video I just recorded of it http://www.youtube.com/watch?v=0ZAc9o3Z4Dc

Hello everyone!
I found this topic which took my attention as I've been having the same issue for some time..
Please excuse my bad english, I'm italian... but I'll try to point everything up the best I can.
Every time I hooked up my macbook pro 13" mid 2010 to the external monitor/TV. I started to hear my hard disk chirping and clicking...
That was worrying me a lot, thinking my hard disk was going to abandon me soon....
But I finally came to a solution!!
Well.. not really a solution, but certainly a workaround.
In my case my Mac is lying on the side of a 46" Led TV which I use also as a monitor for it, hooked up via HDMI cable and HDMI-MiniDV out Hama adapter. I was using a wifi connection.
Then I thought "could it be the wifi antenna disturbing the hard disk when the mac is closed?"
I connected my mac via LAN cable to the router, turned off the wifi, and... my Mac is now quiet as a frozen lake (and a lot faster too)!! ;D
Please let me know if that works for you too.
Cheers!

HT4623 I just got IOS 8 and I cant use my iPod touch 5

My iPod touch 5 isnt working I got the update and now I cant swipe to setup.

If not successful then try the remaining items of:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try another cable
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

Downloaded ios 7 and now password needed

Just downloaded ios 7 and went to use my ipad. It is now password protected which is wasn't before and I have know idea what to do. Says Ipad disabled and can't access anything!

You do not need to unlock the iPad to put it in Recovery Mode.
Here is how to put the device in Recovery Mode:
Connect iPad to your computer via USB while it's turned on.
Open iTunes
Hold the iPad's Sleep/Wake switch (power button on the top of the iPad) down until the "power off" slider appears.
Power off the iPad completely (wait for the progress spinner to disappear).
Hold the Sleep/Wake switch AND the Home button down for a full 10 seconds.
After 10 seconds (the second time you'll see the Apple logo on the screen) release the Sleep/Wake switch while still holding the Home button.
Continue to hold the Home button for another 10 seconds until the USB connection image appears on the iPad's screen, then release the Home button.
A pop-up message will appear on iTunes saying it has detected an iPad in recovery mode, you must restore...
Click on the "Restore" button and the process will begin.

Is it possible to have two USB drives for the IPad? I want to bring RAW photo files from my camera, through the IPad and back to an external hard drive. One of my cameras does not use an SD card. How can I do this?

Is it possible to have two USB drives for the IPad? I want to bring RAW files from my camera through the IPad and out to an external hard drive. One of my cameras has an SD card but the other one doesn't have a card that would fit in any of the camera devices I've seen on line. Realted to this, I bought the IPad camera accessory. Can I put the SD card in the device and also hook the external hard drive to the USB port of the accessory and download from the camera to the hard drive? Can I put Lightroom or the Nikon photo editing software on the IPad? Right now I carry a PC laptop and external hard drives with me on wildernes trips. Internet and WiFi are not available. Because I shoot so many photos and they're in RAW I need to download from the camera to the external drive because I run out of memory on the PC (and it has much more memory than the IPad). I have Nikon NX software and lightroom on my PC. I'd love to be able to reduce the weight I carry by using the IPad to edit my photos each night while on trips. Is this possible and how would I do it? I'd appreciate any guidance.

No, the camera connection kit only supports the copying of photos and videos to the Photos app, it doesn't support copying content off the iPad. For your second camera instead of the SD reader part of the kit, does the iPad to camera cable not work with it for direct transfer to the iPad ?
For Lightroom and Nikon software again no - you can only install apps that are available in the iTunes app store on your computer and the App Store app on the iPad, 'normal' PC and Mac (OS X) software are not compatible with the iPad (iOS). There are some apps that perform fairly basic editing functions that are available in the store, but nothing as sophisticated as, for example, Lightroom.

I want to be able to use airplay to stream audio to another iOS device, and then use that audio stream to be used when recording video instead of the built in microphone / microphone input. Is this possible?

I want to be able to use airplay to stream audio to another iOS device, and then use that audio stream to be used when recording video instead of the built in microphone / microphone input. Is this possible?

A third-party app probably cannot obtain a stream from another app. To the best of my knowledge, such a capability is not provided in the software development kit, apps being "sandboxed" from each other and so allowed to communicate only in very specific and limited ways.
I'm not completely sure what you mean by "limitations on video capture". An iPhone, to the best of my knowledge, can natively record video only through it's built-in camera, and audio while doing video recording only through the built-in microphone or mic/headphone jack. There might be a video recording app that would allow audio input from an external device connected to the dock connector, but I'm not sure.
Regards.

Not enough space on PC for media backup for ios 5.0 upgrade. Can it be config to use external 1T drive, rather than C: drive?

We have iPhone 4 and 3GS, iTouch and Nano.
The PC has about 3GB on the C: drive available, and I have an external USB connected 1T drive which is just about empty.
Can backup / sync functions be changed to use the external drive?
i-device backups and media files have taken over much of my C: drive space.
The iTouch upgrade to ios 5 is stopped because the media would be lost due to insufficient C: drive space. (Requires 3.5GB)

Move all of your media files to the external hard drive, then delete the information on your C: drive. Take a look at this link for instructions. http://support.apple.com/kb/HT1364

Use of groups on External Authentication.

Hi All, I'm triying to use Active Directory groups instead of users in order to authenticate users on ODI 11.1.1.6.
Unfortunately ODI seems to be prepared to use MS AD users, but groups.
Does anybody configure LDAP to authenticate users and got it working with groups?
Thanks and regards!

ODI 11g supports external authentication for users only.

I have 2 macbooks each with an account for me and one for my wife. I use one Macbook logged in with my account and my wife uses the other Macbook only loged in on her account. We both make regular time-machine back-ups each on a separate external disk

I have 2 Macbooks each with an account for me and one for my wife. I use one Macbook logged in with my account and my wife uses the other Macbook only logged in on her account. We both make regular time-machine back-ups each on a separate external disk. Is it possible to update her account on my macbook using her external disk without overwriting my stuff on the same Macbook and vice versa?

Time Machine does not do individual accounts. It records the complete drive. So if you were to use her TM backup on your Mac it would make your Mac just like hers. Both yours and her account on your MAC.
Just copy the missing files over from her Mac to yours. If there are differennt programs on each then they would need to be installed on both.

I just backed up my mac to an external hard drive using Time Machine. What would happen if I turn Time Machine off and then plug the external hard drive back into my computer?

I just backed up my mac to an external hard drive using Time Machine. What would happen if I turn Time Machine off and then plug the external hard drive back into my computer?
What I am ultimately wanting to do is make more room on my computer by backing up all of my files onto the external hard drive and then deleting them off of my computer. However, neededing to be able to retrieve them from the external hard drive later down the road.
From what I have read and am trying to understand, is that I probably shouldn't have used time machine. I need to use the external hard drive like a basic flash drive where I can put things on and get things off without having it automatically update through time machine everytime I connect it to my computer.
Not tech savvy at all and barely understand basics. I need very simple and easy to understand explanations.

sydababy wrote:
and then deleting them off of my computer.
BIG BIG MISTAKE ..... youre making a linchpin deathtrap for your data trying to shove everything on a single fragile HD.
Dont suffer the tragedy other people make, buy another or 2 more HD, theyre cheap as dust.
The number of people who have experienced terror by having a single external HD backup is enormous. One failure that WILL HAPPEN, and kaput,......all gone!
Dont do it, its all about redundancy, redundancy, redundancy.
follow here:
Methodology to protect your data. Backups vs. Archives. Long-term data protection
Deleting them off your computer is fine....having only ONE copy is extremely BAD.
The Tragedy that will be, the tragedy that never should be
Always presume correctly that your data is priceless and takes a very long time to create and often is irreplaceable. Always presume accurately that hard drives are extremely cheap, and you have no excuse not to have multiple redundant copies of your data copied on hard drives and squirreled away several places, lockboxes, safes, fireboxes, offsite and otherwise.
Hard drives aren't prone to failure…hard drives are guaranteed to fail (the very same is true of SSD). Hard drives dont die when aged, hard drives die at any age, and peak in death when young and slowly increase in risk as they age.
Never practice at any time for any reason the false premise and unreal sense of security in thinking your data is safe on any single external hard drive. This is never the case and has proven to be the single most common horrible tragedy of data loss that exists.
Many 100s of millions of hours of lost work and data are lost each year due to this single common false security. This is an unnatural disaster that can avoid by making all data redundant and then redundant again. If you let a $60 additional redundant hard drive and 3 hours of copying stand between you and years of work, then you've made a fundamental mistake countless 1000s of people each year have come to regret.

I just upgraded to iOS 6, and a particular website I always use for school (blackboard) now crashes every time I try to open it. How can this be fixed?

Hi. I just upgraded my iPad 2 to the new iOS 6, and now a website that I use all the time for school is crashing every time I open it to get to my classes and assignments. This is very frustrating since I use my iPad frequently during school. I've already tried rebooting my iPad and closing all applications, and clearing cookies in Safari, nothing has fixed this so far. I feel like it must be related to the update since this did not happen before yesterday when I updated. :( please help!

The problem is with facebook, go to settings / facebook / your user name and delete your account, the do a hard reset (home+power for some seconds).
dont need to delete the facebook app! just delete your integrate account from settings
cheers!

Empty report returned from WEBI and Crystal report when using external hier

Hi,
WEBI and Crystal report build from BEX query returned empty report when we used external hierarchy 0PROFIT_CTR. In BEX we don't have any problems with it.
No authority check is perfomed on the hierarchy when we start the report in WEBI/Crystal. Only check on the hierarchy is performed when the root authorization is assigned to the user

We using BO4 SP12

IOS EZVPN and VPN 3k using external groups

Similar Messages

Maybe you are looking for