IP device tracking

Hi,
We have Cisco 3850 switches and we dont use dot1x but we need to turn off ip device tracking but when I do it from global config mode it pops up the below error:
Switch(config)#no ip device tracking        
% IP device tracking is disabled at the interface level by removing the relevant configs
I've tried disabling it under interface mode even though we don use it.
Can someone please show me how to disable it globally?
Thanks.

I have tried the no ip device track max 10 in interface mode and it accepts it but when I issue " sh ip device tracking int gig 2/0/22 " it still says its enabled.
SW#show ip device tracking interface gig 2/0/22
Enabled interface Configs:
Global IP Device Tracking for clients = Enabled
Global IP Device Tracking Probe Count = 3
Global IP Device Tracking Probe Interval = 30
Global IP Device Tracking Probe Delay Interval = 10
  IP Address    MAC Address   Vlan  Interface           Probe-Timeout      State    Source
Total number interfaces enabled: 64
Enabled interfaces:
  Gi1/0/1, Gi1/0/2, Gi1/0/3, Gi1/0/4, Gi1/0/5, Gi1/0/6, Gi1/0/7,
  Gi1/0/8, Gi1/0/9, Gi1/0/10, Gi1/0/11, Gi1/0/12, Gi1/0/13, Gi1/0/14,
  Gi1/0/15, Gi1/0/16, Gi1/0/17, Gi1/0/18, Gi1/0/19, Gi1/0/20, Gi1/0/21,
  Gi1/0/22, Gi1/0/23, Gi1/0/24, Gi1/1/1, Gi1/1/2, Gi1/1/3, Gi1/1/4,
  Te1/1/1, Te1/1/2, Te1/1/3, Te1/1/4, Gi2/0/1, Gi2/0/2, Gi2/0/3,
  Gi2/0/4, Gi2/0/5, Gi2/0/6, Gi2/0/7, Gi2/0/8, Gi2/0/9, Gi2/0/10,
  Gi2/0/11, Gi2/0/12, Gi2/0/13, Gi2/0/14, Gi2/0/15, Gi2/0/16, Gi2/0/17,
  Gi2/0/18, Gi2/0/19, Gi2/0/20, Gi2/0/21, Gi2/0/22, Gi2/0/23, Gi2/0/24,
  Gi2/1/1, Gi2/1/2, Gi2/1/3, Gi2/1/4, Te2/1/1, Te2/1/2, Te2/1/3,
  Te2/1/4
Here is the show version:
SW#show ver
Cisco IOS Software, IOS-XE Software, Catalyst L3 Switch Software (CAT3K_CAA-UNIVERSALK9-M), Version 03.02.01.SE RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Wed 20-Mar-13 17:10 by prod_rel_team
Cisco IOS-XE software, Copyright (c) 2005-2013 by cisco Systems, Inc.
All rights reserved.  Certain components of Cisco IOS-XE software are
licensed under the GNU General Public License ("GPL") Version 2.0.  The
software code licensed under GPL Version 2.0 is free software that comes
with ABSOLUTELY NO WARRANTY.  You can redistribute and/or modify such
GPL code under the terms of GPL Version 2.0.
(http://www.gnu.org/licenses/gpl-2.0.html) For more details, see the
documentation or "License Notice" file accompanying the IOS-XE software,
or the applicable URL provided on the flyer accompanying the IOS-XE
software.
ROM: IOS-XE ROMMON
BOOTLDR: C3850 Boot Loader (C3850-HBOOT-M) Version 1.1, RELEASE SOFTWARE (P)
SW uptime is 4 weeks, 1 day, 19 hours, 3 minutes
Uptime for this control processor is 4 weeks, 1 day, 19 hours, 6 minutes
System returned to ROM by reload at 12:43:29 WST Sun Sep 8 2013
System restarted at 13:08:55 WST Sun Sep 8 2013
System image file is "flash:packages.conf"
Last reload reason: Reload command
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
License Level: Ipbase
License Type: Permanent
Next reload license Level: Ipbase
cisco WS-C3850-24P (MIPS) processor with 4194304K bytes of physical memory.
Processor board ID FOC1722Z4J9
2 Virtual Ethernet interfaces
56 Gigabit Ethernet interfaces
8 Ten Gigabit Ethernet interfaces
2048K bytes of non-volatile configuration memory.
4194304K bytes of physical memory.
250456K bytes of Crash Files at crashinfo:.
250456K bytes of Crash Files at crashinfo-2:.
1609272K bytes of Flash at flash:.
1609272K bytes of Flash at flash-2:.
0K bytes of Dummy USB Flash at usbflash0:.
0K bytes of Dummy USB Flash at usbflash0-2:.
0K bytes of  at webui:.
Base Ethernet MAC Address          : d0:c7:89:70:a7:00
Motherboard Assembly Number        : 73-12240-10
Motherboard Serial Number          : FOC17215VEG
Model Revision Number              : B0
Motherboard Revision Number        : D0
Model Number                       : WS-C3850-24P
System Serial Number               : FOC1722Z4J9
Switch Ports Model              SW Version        SW Image              Mode  
     1 32    WS-C3850-24P       03.02.01.SE       cat3k_caa-universalk9 INSTALL
     2 32    WS-C3850-24P       03.02.01.SE       cat3k_caa-universalk9 INSTALL
Switch 02
Switch uptime                      : 4 weeks, 1 day, 19 hours, 6 minutes
Base Ethernet MAC Address          : d0:c7:89:70:96:80
Motherboard Assembly Number        : 73-12240-10
Motherboard Serial Number          : FOC17215V33
Model Revision Number              : B0
Motherboard Revision Number        : D0
Model Number                       : WS-C3850-24P
System Serial Number               : FOC1722V19Q
Configuration register is 0x102

Similar Messages

  • Why the command "ip device tracking" can't use in IA 15.2SY0a

    hello
          i configure C6880 with VSS,and use C6800IA with IA,which version is 15.2SY0a,i found a question，when C6800IA run alone without IA uplink to C6880，the command "ip device tracking" can be found and use,but when C6800IA link to C6880 with IA,and C6880 confiure VSS,the command "ip device tracking" can't found and no config,why?

    yes

  • IP device tracking and idle timer problem

    Hi,
    We are deploying 802.1X in our network and have encountered problem with a type of payment terminal.
    The problem is that the terminal do not 'speak' to the network after the first initial DHCP request, the terminal waits for incoming packets from a counter to start the payment process. After the idle-time the MAC is flushed from the switch and the port is not authorized any more.
    To solve this we set 'authentication control-direction in' on the port and use 'ip device tracking' to keep the client on the network, ip device tracking sends an arp request every 30 seconds to clients.
    Our ISE is sending Radius:Idle-Timeout = 300 and the timer start to count down when the client is authenticated.
    In Wireshark, I can see that the ARP request is going out and the ARP reply coming back in but this does not update the inactivity timer for the client. So after 5 minutes the port is gone, and there is no way to get the port up again from the network. Traffic from the client brings up the network.
    This looks like a bug to me, anyone seen this, or a similar behaviour?
    Running:
    ISE 1.2p6
    IOS 12.2(55)SE6
    From Trustsec 1.99 Wired 802.1X Deployment Guide:
    Tip Enable IP Device Tracking with inactivity timers to keep quiet endpoints connected. When IP Device Tracking is enabled, the switch periodically sends ARP probes to endpoints in the IP Device Tracking table (which is initially populated by DHCP requests or ARP from the end point). As long as the endpoint is connected and responds to these probes, the inactivity timer is not triggered and the endpoint is not inadvertently removed from the network.
    From CLI output
    SW03#sh auth sessions int fa0/4
                Interface:  FastEthernet0/4
              MAC Address:  xxxx.xxxx.5289
               IP Address:  10.10.10.64
                User-Name:  XX-XX-XX-XX-52-89
                   Status:  Authz Success
                   Domain:  DATA
           Oper host mode:  multi-auth
         Oper control dir:  both
            Authorized By:  Authentication Server
               Vlan Group:  N/A
          Session timeout:  N/A
             Idle timeout:  300s (server), Remaining: 2s
        Common Session ID:  0A17BD07000000A925152A7B
          Acct Session ID:  0x00000458
                   Handle:  0x090000A9
    Runnable methods list:
           Method   State
           dot1x    Failed over
           mab      Authc Success
    SW03#
    SW03#
    SW03#
    SW03#sh auth sessions int fa0/4
                Interface:  FastEthernet0/4
              MAC Address:  Unknown
               IP Address:  Unknown
                   Status:  Running
                   Domain:  UNKNOWN
           Oper host mode:  multi-auth
         Oper control dir:  both
          Session timeout:  N/A
             Idle timeout:  N/A
        Common Session ID:  0A17BD07000000AA251A0019
          Acct Session ID:  0x00000462
                   Handle:  0x800000AA
    Runnable methods list:
           Method   State
           dot1x    Running
           mab      Not run

    Here is the port config.
    Just to clarify, everything is working except that the terminal is losing the authentication. The terminal works again if traffic is initiated from the terminals menu, like with ping.
    interface FastEthernet0/4
     description Standard
     switchport access vlan xxx
     switchport mode access
     switchport block unicast
     switchport voice vlan xxx
     switchport port-security maximum 2
     switchport port-security
     switchport port-security aging time 5
     switchport port-security violation restrict
     priority-queue out
     authentication control-direction in
     authentication event fail action next-method
     authentication event server dead action reinitialize vlan xxx
     authentication event server dead action authorize voice
     authentication event server alive action reinitialize
     authentication host-mode multi-auth
     authentication order dot1x mab
     authentication priority dot1x mab
     authentication port-control auto
     authentication periodic
     authentication timer reauthenticate server
     authentication timer inactivity server
     authentication violation restrict
     mab
     no snmp trap link-status
     dot1x pae authenticator
     dot1x timeout tx-period 5
     storm-control broadcast level pps 100
     storm-control multicast level pps 100
     storm-control action trap
     spanning-tree portfast
     service-policy input users

  • Version 15.2(1)E on 4900M globally enables ip device tracking and can't remove it

    We wanted to upgrade our 4900M devices to version 15.2(1)E due to some feature for ipv6.
    Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500e-ENTSERVICESK9-M), Version 15.2(1)E, RELEASE SOFTWARE (fc3)
    After the upgrade we started to get error-reports from users that they got duplicate-ip error messages.
    The violating mac-address turned out to be from the upgraded  switch where the vlan passed through, but the switch itself does not  have an ip-address in that vlan. The devices reporting the error are also not connected to the switch.
    We were a bit puzzled about that but then we found that after the upgrade there is an extra line in the config
    "ip device tracking"
    which is something we do not use, but we can't seem to remove it.
    switchname(config)#no ip device tracking
    % IP device tracking is disabled at the interface level by removing the relevant configs
    however, there is no config defined on interface level, and even tried to disable it on interface level anyway, it makes no difference.
    All the interfaces are enabled for ip device tracking as well, and we are also not able to remove an interface.
    Searching the web we find that ip device tracking has been known to be responsable for duplicate-ip errors.
    I have now configured the "workaround"
    ip device tracking probe delay 10
    Don't know yet if it will make a difference but i don't want to finetune or configure a feature we don't use, i would like to disable something which shouldn't have been there in the first place.
    Any thoughts on how to disable the ip device tracking?

    Thanks John,
    after configuring "no macro auto monitor" all the physical interfaces are removed from being IPDT enabled.
    On the 4500-x switch in the lab that even meant all the interfaces and IPDT was disabled globally as well.
    On our production switch (4900M) i seemed to see some different behaviour.
    At first when i tried it, all the physical interfaces where "nmsp attachment suppress" was in place were removed from the IPDT. 
    After some investigation it turns out i also had placed globally "nmsp enable", since the suppress didn't seem to do anything.
    Having "nmsp enabled" is thus a feature that makes ipdt active on a port, but you can counter it by setting nmsp attachment suppress.
    In my case, since i originally didn't have nmsp enabled, i just disabled it again globally.
    The "macro auto monitor"  is apparently, as you point out, also a feature that will enable IPDT on a port.
    Turning it off disabled IPDT on all the physical interfaces.
    Which means i am close to a workaround but not quite, because it doesn't seem to work for the active port-channels.
    It's a bit weird for the port-channels at first sight.
    - configured port-channel, state not-connected -> not IPDT enabled
    - configured port-channel, state up -> IPDT enabled
    - if I shut down a port-channel , so state admin down -> the port-channel as well as the physical member-interfaces are made IPDT enabled. (which considering they are down shouldn't matter much, it is just odd)
    Any thoughts on IPDT with port-channels?

  • Ip device tracking probe delay

    Hi,
     "'ip device tracking probe delay 10 "" , will it means that ,  normally   cisco device (switch or router or firewall) automatically generate the ARP and if this command given it delays for 10 sec ? or it will delay the the unknown flooding for 10 sec ?

    Hi Jithu,
    It actually delay the proble from switch or router for 10 seconds during that time Windows server can sort out the duplicate ip issue detection.
    Explanation from Cisco Site:
    ip device tracking probe delay 10
    The RFC specifies a ten−second window for duplicate address detection, so if you delay the
    device−tracking probe, it resolves the issue in nearly all cases. In addition to probe−delay, the delay
    also resets when the switch detects a probe from the PC. For example, if the probe timer has counted
    down to five seconds and detects an ARP Probe from the PC, the timer resets back to ten seconds. In
    rare circumstances, the PC sends an ARP Probe milliseconds before the switch sends its probe, which
    still triggers a duplicate address message to the end user. This command was introduced in Version
    15.0(1)SE on 2900, 3500, and 3700 Series switch platforms, Version 15.0(2)SG on the 4500 Series
    switch platform, and Version 12.2(33)SXI7 on the 6500 Series switch platform.
    HTH
    Regards
    Karthik

  • "device tracking limit 2" + ip alias == only one IPDT binding

    When I turn on ip device tracking, then set the tracking limit to 2 on a port, then connect a host that is using an ip alias address (same mac, different IP a-la "ip address secondary") then there is only one IP address entry under "show ip device tracking interface XX".  It alternates between the two addresses.  Note one address is not reachable from the switch SVI, so probes might not work, but the switch seems to pick the address up readily from passive ARP.
    Is this normal behavior?  Am I missing a hidden setting?

    This topic is probably better suited in another Infrastructure forum, but I suppose it depends on which features are supported by your Cisco hardware and software. This doc discusses a variety of options:
    http://www.cisco.com/en/US/docs/ios/12_2/qos/configuration/guide/qcfpolsh.html
    For example, with the older CAR (committed access rate) approach:
    interface FastEthernet5/0
         rate-limit input access-group 101 20000000 [normal burst size] [excess burst size] conform-action transmit exceed-action drop
         rate-limit input access-group 102 5120000 [normal burst size] [excess burst size] conform-action transmit exceed-action drop
    access-list 101 permit ip 10.10.10.3 0.0.0.0
    access-list 102 permit ip 10.10.10.4 0.0.0.0
    You can observe CAR in action with "show interfaces fa5/0 rate-limit" for example.

  • I am desperate and seriously need some help - iPhone tracking.

    I’m really hoping one of you can help me.
    Long story short – my daughter aged 6 was taken from me last week because my violent rapist ex husband told Children’s Services that I tried to drive her off a cliff and am a serious suicide risk, I abuse her, I neglect her, I’m an alcoholic, anorexic, complete psycho nutjob etc etc, really nasty stuff. I am desperately trying to get her back. I need to prove I was not at this cliff & in fact have never been there, nor have I ever been stalking his house as he claims (& was awarded a 500m exclusion zone from his house so I can’t get my daughter if I need to as well as a ban on any telephone or postal contact between my daughter & I). I can prove my phone has been used every day for the last 2 years with my bills and if I can prove that in that time I have never been to this cliff, among a million other things I need to try & prove by Wednesday, I have a fighting chance of getting her back. I was allowed supervised visitation today & she’s scared & confused, massively regressed, looking physically neglected, she was withdrawn & was trying to tell me something but being supervised she couldn’t & got told off for whispering. The police are powerless in this & Children’s Services believe him over me, unless I can disprove his claims. Apparently it’s my job to prove their allegations are false rather than them having to prove they’re true!
    Anyway, I’m trying to do the tracking thing on my iPhone 4, IOS 5.1.1.
    I have got so far but I am totally stuck now. Nothing I do seems to work & to be honest half of the instructions may as well be in Swahili to me! It’s all totally over my head & I am not techy enough to understand it, I’m literally Googling every other word to try to understand.
    Please please please can you help me???
    Though I would never normally do it with complete strangers is there any way anyone would be willing to do a remote access thing on my laptop to get the proof I need? Can anyone give me an idiots guide to it? I’m not on Skype or chat or anything but I will get on to it if it helps? Can I ring someone & talk me through it? Can anyone please do anything at all to help my daughter & I??
    I’ve been on http://petewarden.github.com/iPhoneTracker/ & downloaded the app. I’ve also downloaded all the suggested programmes on http://www.26horas.com/apple-device-tracker/ as well as HDXHex thingy, I follow the instructions as far as I can but then I keep getting errors about SQLite3 databases & modules not being found... I have no idea what any of this means but I have heard this technology is no longer valid? Apple has changed it or something? Apparently people whining about big brother & invasion of privacy has made apple change everything & clam up about tracking, but apparently there is still a way, just no one seems to know how!
    Please can you help me? Please, if there is any way you can help me I would owe mine and my daughter’s lives to you. I am desperate and literally on my knees begging you to help me, please. I’ll pay for your time, but please can you help me?

    #1. The iPhone "tracker" you're referring to has already been completely debunked. That is NOT what the data was. In addition, Apple update that "fixed" the percieved problem, so the data is no longer accessible.
    The only way to "prove" what you want to is get a court order for your cellular company to pull the records for the location of your phone over time from their system.
    They know exactly where you phone is at any given moment, but that is not going to be something they will give you just for the asking.
    Get a lawyer.  If you had one, they would have already advised you of this. If you can't afford one, call legal aid.

  • Is there any way in which to turn off automatic step tracking in iOS 8

    I've been using my iPhone 5S for about 4 months now and up until the iOS 8 update was happy with it.
    Since the update - and after opening the health app - I have noticed that the steps I take on a daily basis while the phone is with me are automatically being counted and logged into the health app. Unfortunately for me in this situation, I have a very active job, one in which requires me to walk lots all day, every day. As the phone is with me when I'm walking, the phone is continually logging step data and subsequently my phone battery is dying with astonishing speed; my phone being on 100% charge when I leave the house at 8am and being down to around a mere 30% at around 13:00 (1pm).
    I'm so happy with some of the decisions Apple make on the consumers behalf yet some leave me frustrated and angrily dwelling on switching to an android device after 7 years and many different models of iPhone.
    Apple, I paid £709 for this iPhone a few months ago. It's my phone and I need the battery in it to last for as much of the day as possible. I don't need or want the phone (or any device) tracking how much I move. I know I'm healthy, I don't need to see stats on a smartphone to prove it.
    Please release an update that enables the end user to disengage the health app tracking capabilities.
    I can feel an android device creeping ever closer. And it's just so sincerely unfortunate.

    https://discussions.apple.com/message/23094034#23094034.  Found the answer... Settings, privacy, microphone, and then talking ben...

  • Undo track as intruder in Network Magic

    Hi,
    I accidentaly created a problem. This is what happened: my router is not password protected (long story), therefor I regularly check Network Magic (for which I never registered so I guess I have limited options) and when I see something I don't recognise I click on 'track as intruder' and then remove it from the network. Now it seems I accidentaly branded a cell phone we use in the house as an intruder and removed it from the network and now it won't connect to Wifi anymore. I can't find an option to undo the tracking as intruder because the divice won't show up in Network Magic anymore.
    Can someone tell my how I unblock the phone? You might suggest removing Network Magic from my PC and reinstalling it, but I have no install cd or anything.

    A device tracked as intruder would still be able to connect to the wireless network. The said feature would just notify you each time a device tracked as intruder tries to connect to your network. What you can do is to forget the wireless network profile on your phone and try to reconnect. Also try to reboot your phone and your wireless router. Once the phone is already connected to the network, you should see it on the network map, so you can undo track as intruder.
    Intruders Found in the Network

  • ISE and CDP device sensor

    Hi, all.
    Anyone can explain to me, how the CDP device sensor probe works with ISE ???
    What I am trying to do, is to identify different Cisco Wireless Access Point models (i.e. LAP 1142) with ISE.
    Since the APs do speak CDP (I can see the AP devices on the switch), this should be possible with the CDP device sensor on the switch, shouldn't it  ....
    I have done the following so far:
    Configured the switch to talk to ISE via radius accounting:
    aaa group server radius SERVERGROUP_radius_accounting
         server name ISE02
    radius server ISE02
          address ipv4 [ISE02 ip address] auth-port 1645 acct-port 1646
    radius-server attribute 6 on-for-login-auth
    radius-server attribute 6 support-multiple
    radius-server attribute 8 include-in-access-req
    radius-server attribute 25 access-request include
    radius-server attribute nas-port-id include remote-id
    radius-server dead-criteria time 30 tries 3
    radius-server retry method reorder
    radius-server retransmit 2
    radius-server timeout 2
    radius-server deadtime 1
    radius-server key 7 [ISE02 radius key]
    radius-server vsa send cisco-nas-port
    radius-server vsa send accounting
    radius-server vsa send authentication
    aaa accounting dot1x default start-stop group SERVERGROUP_radius_accounting
    Configured SNMP traps to be sent to ISE:
    snmp-server host [ISE02 ip address] [SNMP RO Community]
    authentication mac-move permit
    authentication critical recovery delay 120 
    mac address-table notification change interval 60
    mac address-table notification change
    mac address-table notification mac-move 
    interface GigabitEthernet0/1
    snmp trap mac-notification change added
    snmp trap mac-notification change removed 
    Configured logging to ISE:
    epm logging
    logging host [ISE02 ip address] transport udp port 20514
    Configured CoA:
    aaa server radius dynamic-author
    client [ISE02 ip address] server-key 7 [ISE02 radius key]
    Configured DHCP snooping, device tracking and device sensors:
    ip dhcp snooping vlan xyz
    no ip dhcp snooping information option
    ip dhcp snooping
    ip device tracking
    device-sensor filter-list dhcp list DSFL_dhcp
    option name domain-name-servers
    option name host-name
    option name domain-name
    option name class-identifier
    option name client-identifier
    device-sensor filter-list lldp list DSFL_lldp
    tlv name system-name
    tlv name system-description
    tlv name system-capabilities
    tlv name management-address
    device-sensor filter-list cdp list DSFL_cdp
    tlv name device-name
    tlv name port-id-type
    tlv name capabilities-type
    tlv name version-type
    tlv name platform-type
    tlv name duplex-type
    tlv number 34
    device-sensor filter-spec dhcp include list DSFL_dhcp
    device-sensor filter-spec lldp include list DSFL_lldp
    device-sensor filter-spec cdp include list DSFL_cdp
    device-sensor notify all-changes
    Configured an additional IP helper on the AP vlan pointing to ISE:
    interface vlan xyz
    ip helper-address [ISE02 ip address]
    I have configured new profiling conditions on ISE, which use the cdp attributes:
    and used these conditions in a new profiling policy for the 114x AP:
    ISE is configured to listen to DHCP, radius, DNS and SNMP traps ....
    However, the only thing ISE sees of this AP, is the dhcp probe:
    and therefore, the 114x policy has no effect .......
    ISE version is the following:
    Cisco Application Deployment Engine OS Release: 2.0
    ADE-OS Build Version: 2.0.4.018
    ADE-OS System Architecture: i386
    Copyright (c) 2005-2011 by Cisco Systems, Inc.
    All rights reserved.
    Hostname: deess01nise02
    Version information of installed applications
    Cisco Identity Services Engine
    Version      : 1.1.2.145
    Build Date   : Fri Oct 26 21:10:35 2012
    Install Date : Fri Jan 18 07:18:49 2013
    Cisco Identity Services Engine Patch
    Version      : 2
    Install Date : Mon Jan 21 07:36:50 2013
    Cisco Identity Services Engine Patch
    Version      : 3
    Install Date : Mon Jan 21 07:42:11 2013
    Version of the switch:
    cisco WS-C3560CG-8PC-S (PowerPC) processor (revision C0) with 131072K bytes of memory.
    Processor board ID FOC1619Y180
    Last reset from power-on
    7 Virtual Ethernet interfaces
    10 Gigabit Ethernet interfaces
    The password-recovery mechanism is enabled.
    512K bytes of flash-simulated non-volatile configuration memory.
    Base ethernet MAC Address       : 58:BF:EA:B9:AC:80
    Motherboard assembly number     : 73-13272-06
    Power supply part number        : 341-0407-01
    Motherboard serial number       : FOC16174ZZ5
    Power supply serial number      : LIT16120XR8
    Model revision number           : C0
    Motherboard revision number     : A0
    Model number                    : WS-C3560CG-8PC-S
    System serial number            : FOC1619Y180
    Top Assembly Part Number        : 800-33676-02
    Top Assembly Revision Number    : A0
    Version ID                      : V02
    CLEI Code Number                : CMMD900ARB
    Hardware Board Revision Number  : 0x00
    Switch Ports Model              SW Version            SW Image
    *    1 10    WS-C3560CG-8PC-S   15.0(2)SE             C3560c405ex-UNIVERSALK9-M   
    What am I missing ??? Should this config make the switch send CDP information about connected devices to the ISE (via radius accounting) ???
    How do the device sensors work ???
    Rgs
    Frank

    A switch with sensor capability gathers  endpoint information from network devices using protocols such as Cisco  Discovery Protocol (CDP), LLDP, and DHCP, subject to statically configured  filters, and makes this information available to its registered clients in the  context of an access session. An access session represents an endpoint's  connection to the network device
    Client notifications and accounting  messages containing profiling data along with the session events, and other  session-related data, such as MAC address and ingress port are generated and  sent to the internal and external clients (ISE). By default, for each supported  peer protocol, client notifications and accounting events are only generated  where an incoming packet includes a TLV that has not previously been received in  the context of a given session. You can enable client notifications and  accounting events for all TLV changes, where either a new TLV has been received  or a previously received TLV has been received with a different value using CLI  commands.
    http://www.cisco.com/en/US/docs/switches/lan/catalyst3750/software/release/15.0_1_se/device_sensor/guide/sensor_guide.html#wp1112722

  • IP discovery tracking. Cant configure under interface.

    I was tasked to re-IP a network and its being done by floor. I need to figure out what iP addresses are connected to ports on each switch. Half the range is being re-numberd while others stay the same. Everything is currently on the same subnet and VLAN so I can differentiate by VLANs. There are over 1000 hosts so tracing mac to ip addresses through "show ip arp" will take entirely too long. I have been using "ip device tracking" on all of the 3750 switches and it works great but I cant configure it on the two 4506-E switches I have. I can configure it globally but the option is not available under the interface. Its running IP-base-12.2(53)SG upgrading to ip services in a week. Has anybody had this issue, or am I missing a command somewhere. I check the configuration guide and its shows that the config is valid for that platform and ios.
    BTW: I cant configure it on the core 6513 either its running advancedenterprise12.2 (53)
    Sent from Cisco Technical Support Android App

    I was tasked to re-IP a network and its being done by floor. I need to figure out what iP addresses are connected to ports on each switch. Half the range is being re-numberd while others stay the same. Everything is currently on the same subnet and VLAN so I can differentiate by VLANs. There are over 1000 hosts so tracing mac to ip addresses through "show ip arp" will take entirely too long. I have been using "ip device tracking" on all of the 3750 switches and it works great but I cant configure it on the two 4506-E switches I have. I can configure it globally but the option is not available under the interface. Its running IP-base-12.2(53)SG upgrading to ip services in a week. Has anybody had this issue, or am I missing a command somewhere. I check the configuration guide and its shows that the config is valid for that platform and ios.
    BTW: I cant configure it on the core 6513 either its running advancedenterprise12.2 (53)
    Sent from Cisco Technical Support Android App

  • IPhone Developer Center: Unable to remove/edit devices under Device Manage

    Hello.
    We just got a device tracker built into our bug tracker. I would like to go through and change the names of the devices listed off in the Manage tab under Devices. The Howto tells me there should be a button to either edit or remove an item from the list. I don't see such button. Am I the only one noticing this issue?
    Thanks.

    Hi barryg9999,
    Strange one I must admit however just wanted to check if you turn iTunes Match off on your iPhone does the song disappear? There are 2 settings for the Music app, Show all music will refer to iTunes store purchases you've made which are in the cloud and can be restored to your device at any time, iTunes Match being the songs you didn't purchase from the iTunes store.
    If you open Settings > Music and scroll down you should see the option to turn off iTunes match which will allow you to test this.
    If the track is on iTunes match which I suspect it is you can delete it from Match using iTunes on a PC or Mac by removing it from the iTunes library and telling iTunes to update Match once the track is removed.
    I hope this helps.

  • How can we find the hostname of the devices connected with the interfaces of switch?

    how can we find the hostname of the devices connected with the interfaces of switch ? I have tried mac address and ARP, there are lot of servers connected with the switch having multiples LAN cards. So mac table shows the mac of physical machine as well as virtual machines. But i want to know only the physical machines. Is there any other method to find out the IP address, hostname of the physical machines only? 

    Hello Leo Laohoo
    Thanks for this information
    In our network most of the Servers are not of Cisco. Some of them are Vmware machines, some are Hyper V machines, etc. 
    Does IP device tracking show us only the IP addresses of the Physical Machines of the Vmware Server not of Virtual Machines?
    Regards
    Mukesh Kumar
    Network Engineer 
    Spooster IT Services

  • Lifelines trackit EEG recording with LabVIEW

    Hi, I am trying to control a lifelines trackit EEG (www.llines.com) recorder using LabVIEW via serial communication (DB9). Does anyone has any experiences connecting this device with labview? I've done several communication via serial communication with labview before but not as tough and difficult as the current task. I am not able to understand the device (trackit) command in order for me to apply the Basic Serial Read and Write VI. Please advice. I have the Lifelines trackit recorder Interface specification in softcopy as reference but do not know how to attach here. Please let me know if you guys need the  copy as reference. TQVM
    Host Transmit Write Data and Write Command
    [SOP] <AddrHi> <AddrLo> [Chr(W)] <ParamBlock> <Index> [EOP]
    Or:
    [SOP] <AddrHi> <AddrLo> [Chr(W)] <ParamBlock> <Index> [Data]# [EOP]
    Or:
    [SOP] <AddrHi> <AddrLo> [Chr(W)] <ParamBlock> <Index> <Data># [EOP]
    Or:
    [SOP] <AddrHi> <AddrLo> [Chr(W)] <ParamBlock> <Index> {Data}# [EOP]

    Is there a demo program from the manufacturer that works?? you can use portmon or NI spy to capture the serial datastream and reverse engineer the labview code. Sometimes ya have to think like a hacker.
    http://technet.microsoft.com/en-us/sysinternals/bb896644.aspx
    http://www.ni.com/support/gpib/max/nispy.htm
    Message Edited by unclebump on 02-16-2009 08:34 PM

  • How can I access my iCloud account on the web from my phone

    how can I access my iCloud account on the web from my phone
    iPhone 5 iOS 8.3
    I have iCloud turned on, location services on, find my phone works but when I try to access iCloud via Safari on the phone it takes me to a page Apple.com,
    iCloud then three options
    set up iCloud on my phone (i have)
    Install Find my phone, it is installed and it works from my MBP
    or install find my friends, I don't need that I have no friends.
    my calendars and contacts and bookmarks and all are all sync'd and working on the phone, but i thought if I typed in iCloud.com on the phone in Safari I would go to my iCloud web page that looks like this on my Mac.
    Is that NOT how iCloud should/would look on my phone via Safari?
    This is maybe a dumb question after 3+ year of iPhone'ing
    thank you for clarifying or helping me to understand
    jojoguitar_mmn_usa

    I've been playing with a Galaxy here at work and here's what I've found so far - please feel free to jump in and suggest alternative methods to configure or access the various icloud components.
    So the original Q: Can you access your icloud account on Android?
    Not entirely: the website can't be used from an android browser (not properly - even with Dolphin HD and posing as different browsers it won't load correctly.  So Find my iphone is out, so is the address book or looking at your e-mail or calendar just in a browser window
    I was able to setup my e-mail using the IMAP settings published here:
    http://support.apple.com/kb/HT4864
    Be sure to setup the account manually - and note if you have trouble using SSL try TLS (that worked for me)
    Address book is a no go so you'll have to use iTunes to sync all your contacts over to Gmail - if you still have an iPad it means managing contacts in two places though .  Same goes for your calendar - transfer it to Gmail and forget about iCloud's calendar.  Nice instructions here: http://howto.cnet.com/8301-11310_39-20064060-285/how-to-switch-from-iphone-to-an droid/
    iWork is an Apple proprietary bit so don't expect much there.
    So in my case, if I'm really going to make the switch to a Galaxy from my iPhone it really means I'm going to have to switch to using google as the backend.  The timing to swap over to a galaxy/android phone is not the greatest - given that I'd have to give up my Apple addiction (syncing photos and itunes and losing access to my device tracking).  Plus I still have an iPad and a mac and like living in the Apple ecosystem.  I think I'll wait and see what the new iPhone looks like before I commit

Maybe you are looking for

  • Compare values in a Column.

    Hi, I have an requirement like below and would like to have SQL for that. Source Table:+ EMP_NO     EMP_CODE 1          'A' 1          'D' 1          'E' 1          'F' 2          'S' 2          'A' 2          'W' 2          'Q' 3          'A' 3     

  • Excise internal document getting reversed on reversal of GR(Imports)

    Hi! On reversal of imported GR docuement, the internal document is getting reversed resulting in-correct figure in the part-1 register. e.g : I have 3 documents in a PO(Qty-10MT), i.e. GR1-5MT, GR2-3MT & GR3-2MT     At this point the Entered field wi

  • While updating to iOS 6 I lost EVERYTHING! HELP!!

    I have figured out how to sync my apps back to my phone however when I try to find my contacts sync them back and my photos back I can't find them ANYWHERE in iTunes. Please tell me they are not gone forever! I had over 1300 pics on here! PLEASE HELP

  • Browse Buttons in B1

    I am working oncreating a customiztion for a client. Basically its a custom form created in screenpainter that users use to enter some data that gets stored in a user define table. One of the features I would like to add to this form is the ability f

  • Help to overcome 32K XML limit for Anychart  Map

    Hello, Apex version 4.2.0.00.27 I am creating a heat map using the Anychart maps and have chosen to use the "Use custom XML" option in the Map Attributes to control the map being generated. However, I have hit a 32K limit for 'Custom XML' that is bei