IP discovery tracking. Cant configure under interface.

I was tasked to re-IP a network and its being done by floor. I need to figure out what iP addresses are connected to ports on each switch. Half the range is being re-numberd while others stay the same. Everything is currently on the same subnet and VLAN so I can differentiate by VLANs. There are over 1000 hosts so tracing mac to ip addresses through "show ip arp" will take entirely too long. I have been using "ip device tracking" on all of the 3750 switches and it works great but I cant configure it on the two 4506-E switches I have. I can configure it globally but the option is not available under the interface. Its running IP-base-12.2(53)SG upgrading to ip services in a week. Has anybody had this issue, or am I missing a command somewhere. I check the configuration guide and its shows that the config is valid for that platform and ios.
BTW: I cant configure it on the core 6513 either its running advancedenterprise12.2 (53)
Sent from Cisco Technical Support Android App

Similar Messages

Ssid configuration can be done at config level as well as under interface level : which will be recommanded

Hi,
I need to configure two ssids in 1142 aps and i have gone some cisco documents where it is mentioned that we can configure ssid in config mode as well as under interface mode.
which one will be convenient method to configure ?
Particularly i am looking for 1142 configuration .....

Hi Vinod,
We need to configure the SSID in both.. that is under config mode and also under interface..lemme be clear.. the one which we configure under config mode is to configure the SSID.. so configureing SSID alone will not help us in getting the wireless netwok up and running.. so we need t ouse this SSID for radio so that it gets broadcasted... so both are needed.. that is..
************** This is to configure the SSID *****************
conf t
dot11 ssid
end
****************** This is like giving life to the configured SSID****************
conf t
int dot11 0 / 1
ssid
lemme know if this answered your question..
Regards
Surendra
==========
Please dont forget the rate the usefull posts and also if this was helpfull for you..

Failed to configure IPv6 interface(s): eri1 - how to debug?

I have a problem configuring the second network interface for IPv6 under Solaris 10. The first interface, eri0, is configured and works fine. The second one, eri1, has a link-local address but no global address. Both links are up and working, I can ping eri1 via IPv4 (10.0.1.9) from an external host.
netra / $ ifconfig -a6
lo0: flags=2002000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv6,VIRTUAL> mtu 8252 index 1
        inet6 ::1/128
lo0:1: flags=2002000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv6,VIRTUAL> mtu 8252 index 1
        zone wibble
        inet6 ::1/128
lo0:2: flags=2002000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv6,VIRTUAL> mtu 8252 index 1
        zone foobar
        inet6 ::1/128
eri0: flags=2000841<UP,RUNNING,MULTICAST,IPv6> mtu 1500 index 2
        inet6 fe80::203:baff:fe0b:fd4b/10
        ether 0:3:ba:b:fd:4b
eri0:1: flags=2080841<UP,RUNNING,MULTICAST,ADDRCONF,IPv6> mtu 1500 index 2
        inet6 2001:0:0:1:203:baff:fe0b:fd4b/64
eri0:2: flags=2000841<UP,RUNNING,MULTICAST,IPv6> mtu 1500 index 2
        zone wibble
        inet6 2001:0:0:1::4/64
eri0:3: flags=2000841<UP,RUNNING,MULTICAST,IPv6> mtu 1500 index 2
        zone wibble
        inet6 fe80::213:a9ff:fe80:43c0/10
eri0:4: flags=2000841<UP,RUNNING,MULTICAST,IPv6> mtu 1500 index 2
        zone foobar
        inet6 2001:0:0:1::3/64
eri0:5: flags=2000841<UP,RUNNING,MULTICAST,IPv6> mtu 1500 index 2
        zone foobar
        inet6 fe80::213:a9ff:fe80:43bf/10
eri1: flags=2004841<UP,RUNNING,MULTICAST,DHCP,IPv6> mtu 1500 index 3
        inet6 fe80::203:baff:fe0b:fd4b/10
        ether 0:3:ba:b:fd:4bMy setup is the same for both interfaces:
- empty files /etc/hostname6.eri0 and /etc/hostname6.eri1
- both NICs connected to the same switch, with a L2-adjacent IPv6 router.
Last messages from the serial console are:
Failed to configure IPv6 interface(s): eri1
SUNW,eri0 : 100 Mbps full duplex link up
Hostname: netra
SUNW,eri1 : 100 Mbps full duplex link up
(at this point, I issued 'svcadm restart network/physical')
Failed to configure IPv6 interface(s): eri1
Aug 30 16:59:29 netra in.ndpd[259]: phyint_init_from_k: SIOCLIFGETND (interface eri1): No such process
Aug 30 16:59:29 netra last message repeated 1 time
Aug 30 16:59:29 netra in.ndpd[259]: Interface eri1 has been removed from kernel. in.ndpd will no longer use it
Do you have any ideas? Where to look?
Maciej
Edited by: automatthias on Aug 30, 2008 9:12 AM
Edited by: automatthias on Aug 30, 2008 9:12 AM

Thank you for the answer! I've found an option 'local-mac-address?' (the question mark is a part of the parameter name) in the 'ok' prompt.
More info for next generations:
1. Get to the 'ok prompt' (OpenBoot prom)
2. Type 'printenv' to see the current settings, look for 'local-mac-address?'
3. Set the parameter to 'true': 'setenv local-mac-address? true'
4. Type printenv again to see if the option was actually changed
This option is also described in Gentoo OBP reference:
http://www.gentoo.org/doc/en/gentoo-sparc-obpreference.xml
Thanks!
Maciej

Cisco 3640 cant configure voice-ports

I've an cisco 3640 with a VWIC-2MFT-E1 network module. Can anybody tell me why i cant configure any voice-port? without able to configure voice-port, i cant assign any port for my "dial-peer voice xx pots". Anybody has any solution?
what im trying to do is sending voice data traffic to 192.168.10.1
controller E1 1/0
framing NO-CRC4
clock source line primary
channel-group 0 timeslots 1-31
interface Serial1/0:0
bandwidth 2048
ip address 192.168.10.2 255.255.255.252
ip mtu 300
encapsulation ppp
no ip route-cache
no fair-queue
no cdp enable
dial-peer voice 777 pots
destination-pattern 77T
no digit-strip
direct-inward-dial
forward-digits all

I've only got this from my controller E1
Vertigo(config-controller)#?
Controller configuration commands:
channel-group     Specify the timeslots to channel-group mapping for an
                    interface
clock             Specify the clock source for a DS1 link
default           Set a command to its defaults
description       Controller specific description
detect            Enable detection of loopback request
exit              Exit from controller configuration mode
framing           Specify the type of Framing on a E1 link
guard-timer       Guard timer (0-20) for xcsp calls - timer duration and
                    accept/reject on expiry
help              Description of the interactive help system
line-termination Specify the line termination for E1
linecode          Specify the line encoding method for a E1 link
loopback          Put the entire E1 line into loopback
mode              Configure the controller mode
no                Negate a command or set its defaults
shutdown          Shut down a E1 link (send Blue Alarm)
tdm-group         Configure DS0 group for TDM
Do i need DSP for the voice-ports? Please guide me on what more module i need to get. Thanks!!
https://supportforums.cisco.com/message/3022639;jsessionid=AF45FBC0DDB8636D70F9B526A367016F.node0

HSRP Interface Tracking on ATM Sub-Interface?

I want to enable HSRP interface tracking to monitor an ATM sub-interface. As I understand it, when using the (standby 1 track <interface>) command, the HSRP group priority will be decremented only if the line protocol goes down on the interface being tracked. For this reason I need to track an ATM sub-interface (i.e. atm1/0.77). I am wondering if this will work properly. Has anyone ever used this configuration successfully?

Hi Friend,
I find no reason why it should not work?
When it work for serial subinterface and frame relay interfces it should also work for atm subinterface.
I have implemented in serial subinterface.
Yes it should work fine. Go ahead and implement and update the status.
Regards,
Ankur

Configuring BRI interface for Voice ( MGCP gateway

hi there,
i have a Call Manager which is connect to Cisco 2800 series acting as MGCP getway. ISDN connection between the 2800 and the carrier ( telestra sydney ). the call manager is seeing the gateway and i have configured a numbering plan on the call manager for the phones. the phones can call internally but externally i dont what configuration i should configure under the BRI interface for the carrier ( telestra ) to recongnise my number plan. please if you have any demo configuration or configuration that has perviously used post to me.

this is a basic MGCP config on the Gateway on your area
BRI Switchtype Information
BRIs in Australia require no service profile identifiers (SPIDs).
There are two ISDN switch-types that can be used:
basic-net3?Currently the most commonly used.
basic-ts013?For older ISDN switches such as MicroLink.
isdn switch-type basic-net3 or 5
voice-card 2
dspfarm
dsp services dspfarm
controller T1 2/0
description T1 link to SRST
framing esf !--- Automatic method automatically adds
clock source internal
linecode b8zs !--- Automatic method automatically adds
cablelength short 133
pri-group timeslots 1-2,24 service mgcp !--- Automatic method
!--- automatically adds 24 channels.
!---You can manually edit channels.
description T1 link to SRST
interface Serial2/0:23
no ip address
isdn switch-type primary-ni !--- Automatic method automatically adds
isdn protocol-emulate network !--- Simulated Lab ISDN
isdn bind-l3 ccm-manager !--- Allows all Q931 to be backhauled over TCP to
!--- CallManager; automatic method automatically adds
no cdp enable !--- Automatic method automatically adds
ccm-manager mgcp
ccm-manager music-on-hold
ccm-manager config server 171.69.103.225
ccm-manager config !--- Enables automatic config download from CallManager
!--- Automatic method automatically adds these commands
mgcp
mgcp call-agent 171.69.103.225 2427 service-type mgcp version 0.1
mgcp dtmf-relay voip codec all mode out-of-band
mgcp rtp unreachable timeout 1000 action notify
mgcp modem passthrough voip mode nse
mgcp package-capability rtp-package
mgcp package-capability sst-package
no mgcp package-capability fxr-package
mgcp package-capability pre-package
no mgcp timer receive-rtcp
mgcp sdp simple
mgcp fax t38 inhibit
mgcp rtp payload-type g726r16 static
mgcp profile default

Error: Datasource Configuration under planning

After Successful configuration of
1) Foundation Services (Hyperion Shared Services)
2) Essbase administration services
3) Essbase Server
4) Hyperion reporting and analysis
5) Planning -----> Product options, Register with shared services, configure database, deploy to application server (Appache), Product Instance registration.
I stuck with Datasource Configuration under planning-
Steps in details---
cheked on data source configuration and click next
check create datasource and click next
datasource name : essdb (my choice)
datasource Discription : essbase DB (my choice) click next
select my instance name : plan (from drop down menu) click next
Select Database : MS SQL server click next
Database type: SQL
Port: 1433 (Default)
Database Details:
Product: planning
database : p2DB (new DB, SQL)
user: p2user (new user, SQL)
password: ***
click next
Essbase server information:
Sever : my machine name (neeraj-pc)
user : planning (created new essbase user, external)
password : ******
Click next
Error:
at java.awt.Component.processMouseEvent(Unknown Source)
at javax.swing.JComponent.processMouseEvent(Unknown Source)
at java.awt.Component.processEvent(Unknown Source)
at java.awt.Container.processEvent(Unknown Source)
at java.awt.Component.dispatchEventImpl(Unknown Source)
at java.awt.Container.dispatchEventImpl(Unknown Source)
at java.awt.Component.dispatchEvent(Unknown Source)
at java.awt.LightweightDispatcher.retargetMouseEvent(Unknown Source)
at java.awt.LightweightDispatcher.processMouseEvent(Unknown Source)
at java.awt.LightweightDispatcher.dispatchEvent(Unknown Source)
at java.awt.Container.dispatchEventImpl(Unknown Source)
at java.awt.Window.dispatchEventImpl(Unknown Source)
at java.awt.Component.dispatchEvent(Unknown Source)
at java.awt.EventQueue.dispatchEvent(Unknown Source)
at java.awt.EventDispatchThread.pumpOneEventForHierarchy(Unknown Source)
at java.awt.EventDispatchThread.pumpEventsForHierarchy(Unknown Source)
at java.awt.EventDispatchThread.pumpEvents(Unknown Source)
at java.awt.EventDispatchThread.pumpEvents(Unknown Source)
at java.awt.EventDispatchThread.run(Unknown Source)
Kindly suggest steps to cofg correctly

details of configtool_err (Hyperion-> Logs--> Config)
(Dec 05, 2008, 06:03:22 AM), com.hyperion.planning.HspDSRdbPanelManager, ERROR, Relational Database Connection Failed:= :[Hyperion][SQLServer JDBC Driver][SQLServer]Login failed for user 'p2user'.
(Dec 05, 2008, 06:15:12 AM), com.hyperion.planning.HspDSRdbPanelManager, ERROR, Relational Database Connection Failed:= :[Hyperion][SQLServer JDBC Driver]Error establishing socket to host and port: 220.226.46.164:1433. Reason: Network is unreachable: connect
(Dec 05, 2008, 10:10:06 AM), com.hyperion.planning.HspDSRdbPanelManager, ERROR, Relational Database Connection Failed:= :[Hyperion][SQLServer JDBC Driver][SQLServer]Login failed for user 'p2user'.
Regards
Kumar N

Configure ce interface to accept all frames (regardless of 802.1q tag)?

On Solaris 9,
is it possible to configure a ce interface so it accepts
all Ethernet frames it receives, regardless of the presence,
absence, or value of an 802.1q tag?
I'm trying to run packet sniffing software on a ce interface
(I'm not using the interface for IP). The Ethernet switch
I'm attached to forwards to me copies of traffic from many
different VLANs, via a port mirroring function. Most of
this traffic is tagged with various 802.1q VLAN tags.
Some of this traffic may be untagged.
My difficulty is that since the Sun Gigaswift 'ce' interface
supports 802.1q, if I configure the interface so it
doesn't "do" VLANs (e.g. 'ifconfig ce5 plumb'), the ce interface
discards any incoming frames that have 802.1q tags.
Alternatively, if I configure the ce interface so it "does"
VLANs (e.g. 'ifconfig ce10005 plumb'), I end up having to
configure dozens of logical ce interfaces (one per VLAN) each
of which will only receive frames tagged for one particular VLAN;
I don't end up with an interface that receives all VLAN frames.
I want one logical interface that receives all the frames,
so I can point my sniffing software at it.
There's no problem doing this with a card that doesn't support
802.1q, since that card will happily accept all frames and pass
them up. So I can do this on qfe or bge interfaces. But I need
to do this using interfaces available on a PCI card
(my V880 has several port mirrors coming from various Ethernet switches),
the interfaces need to be 1000 Mbps (which rules out the qfe card), and
I'd like to stay with copper (which rules out the bge card).
That's why I'm trying to do it with the quad ce card, but I'm
stymied by it support for 802.1q. (If there were just some way
I could turn off 802.1q support for specific ce instances.)
Is there a way I can accomplish this with the
copper Gigaswift interface (Cassini driver) in Solaris 9?
If not, is there another 1000 Mbps copper interface (provided on PCI card)
that can do this?
Or does this become possible in Solaris 10?

Oops, when I wrote "bge" above, I meant "ge", of course.
(ge is fiber gigagbit ethernet interface and doesn't know about 802.1q.)

Create a configurable Web Interfaces

Good Afternoon,
I would like to build a Web application using JSP, Servlets and Struts. However I want that the users could configure their interfaces once they are logged. By configuring interface, I mean that a user could choose to hide/show an input of a form and chose if this input is read-only or not.
I've though it would be a good idea of using a simple XML configuration file for each user to do that like this one :
<config>
<ITEM ID="name_input">
<DISPLAY>1</DISPLAY>
<CHANGE>1</CHANGE>
</ITEM>
<config>
By the way, I must use the i18n tag to manage the translation of my application in different language.
I'm a beginner in using these technologies and I'd like to have some advises from someone who did a configurable Web application.
I hope Someone will help me.
Thank you very much
Xavier

hello, ive also started to build a web site that will allow some configuration.
But im using a bd to store all info for the web site.
I dont know how good it is to use xml file or struct to configure dynamicaly since i dont use/know how to use this technologie.
As for the bd case, you need at least 1 table per web page and some info to identifie eatch user parameters, also, you could need to keep a table with user login/info as to identifie them.
To keep the language for every user, you may need to put extra field in eatch web page table.
Hope this can help you :)

SATA Drives - Opposite Configuration under Windows XP

I have 2 HDDs - 160GB and 80GB.
I plug 160GB into SATA 1 and 80GB into SATA 2 on motherboard (MSI 865PE Neo2-PLS).
In BIOS, 160GB is "Primary IDE" and 80GB is "Secondary IDE".
I installed Windows XP SP2 in 160GB. 80GB remains plugged in SATA 2.
In Windows under "Disk Management" (in Control Panel), my 80GB was configured as Disk 0 (marked "Acitve") and 160GB was Disk 1 (even though 160GB contains the XP System files).
(Q1) How do I re-configure this to 160GB as Disk 0 and 80GB as Disk 1 under Windows?
(Q2) Are my BIOS settings wrong?
Thanks!

Quote
Originally posted by NovJoe
Re-install windows with only the 160GB in to force it to be the main system drive.
I did re-install Windows XP this afternoon with only 160GB plugged in.
After that, I re-booted with 80GB plugged in.
Strange, the same problem remains - 80GB still configured under Disk 0 and 160GB under Disk 1.
Is something wrong with my CMOS settings? I was thinking of resetting my BIOS to standard default settings. Would this harm my Windows XP booting, functioning, etc in any way after Windows installation?
Thanks NovJoe!!

Problem in configuring IPv6 interface with default Router lifetime.

I'm facing Problem in configuring IPv6 interface with default
Router lifetime through a router advertisement.
I'm also see an unusual behavior that even after configuring accept_rtadv=0,
the ipv6 address is configured.
Please help in out .

Mac OS 9 does not support IPv6. While you can have IPv6 on your network, a Macintosh running Mac OS 9.2.2 or earlier cannot make connections to services using this network protocol.
To use IPv6 on a Macintosh, you need Mac OS X 10.1 or later (as far as I know).
—tonza

In.mpathd: No test address configured on interface

Hi,
I am getting error messages related to multipathing in dmesg output
May 10 02:29:29 sskidb2 in.mpathd[165]: [ID 975029 daemon.error] No test address configured on interface ce2; disabling probe-based failure detection on it
May 10 02:29:29 sskidb2 in.mpathd[165]: [ID 975029 daemon.error] No test address configured on interface ce0; disabling probe-based failure detection on it
below the /etc/hostname.ce files:
bash-3.00#more hostname.ce0
192.168.50.58 netmask + broadcast + group primary_ipmp up addif 192.168.50.64 deprecated netmask + broadcast + up
bash-3.00#more hostname.ce1
192.168.50.62 netmask + broadcast + deprecated group primary_ipmp -failover standby up
bash-3.00#more hostname.ce2
172.16.50.68 netmask + broadcast + group iconnect_ipmp up addif 172.16.50.72 deprecated netmask + broadcast + up
bash-3.00#more hostname.ce3
172.16.50.70 netmask + broadcast + deprecated group iconnect_ipmp -failover standby up
Below ifconfig output:
/usr/sbin/ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
ce0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet 192.168.50.58 netmask ffffff00 broadcast 192.168.50.255
groupname primary_ipmp
ce0:1: flags=1040843<UP,BROADCAST,RUNNING,MULTICAST,DEPRECATED,IPv4> mtu 1500 index 2
inet 192.168.50.64 netmask ffffff00 broadcast 192.168.50.255
ce0:2: flags=1040843<UP,BROADCAST,RUNNING,MULTICAST,DEPRECATED,IPv4> mtu 1500 index 2
inet 192.168.50.60 netmask ffffff00 broadcast 192.168.50.255
ce1: flags=69040843<UP,BROADCAST,RUNNING,MULTICAST,DEPRECATED,IPv4,NOFAILOVER,STANDBY,INACTIVE> mtu 1500 index 3
inet 192.168.50.62 netmask ffffff00 broadcast 192.168.50.255
groupname primary_ipmp
ce2: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 4
inet 172.16.50.68 netmask ffff0000 broadcast 172.16.255.255
groupname iconnect_ipmp
ce2:1: flags=1040843<UP,BROADCAST,RUNNING,MULTICAST,DEPRECATED,IPv4> mtu 1500 index 4
inet 172.16.50.72 netmask ffff0000 broadcast 172.16.255.255
ce3: flags=69040843<UP,BROADCAST,RUNNING,MULTICAST,DEPRECATED,IPv4,NOFAILOVER,STANDBY,INACTIVE> mtu 1500 index 5
inet 172.16.50.70 netmask ffff0000 broadcast 172.16.255.255
groupname iconnect_ipmp
What can be the possible reason for this.
Pls reply.
Thanks.
Harish Maliwal

hi,
configure the test address in the stand by interface.

JET install: ERROR: Unable to configure network interface Exiting to shell

Using SUNWjet v4.4.4 I'm trying to build a server using update 5 x86 which seems
to work with one notable exception. The JET server and the build server do not
reside on the same subnet. In order to get around not being able use PXE boot
to boot the build server I'm booting from DVD after making the following modifications
to the grub menu entry:
kernel /I86PC.Solaris_10-1/multiboot kernel/unix - install nowin -B
install_config=x.x.x.x:/opt/SUNWjet,
sysid_config=x.x.x.x:/opt/SUNWjet/Clients/testclient,
install_media=x.x.x.x:/export/install/media/s10u5-x86,
install_boot=x.x.x.x:/export/install/media/s10u5-x86/boot
This seems to kick off the installer however it fails to bring up the network interface:
SunOS release
Configuring devices
Solaris Interactive Text ( Console Session )
ERROR: Unable to configure network interface Exiting to shell
# ifconfig bge0 x.x.x.x up netmask 255.255.255.0
# route add default x.x.x.1
# exit
Using RPC
Installation continues without any errors
It seems that I'm forced to bring up the interface manually each time.
This is what the template looks like:
base_config_ClientArch=i86pc
base_config_ClientEther=XX:XX:XX:XX:XX:XX
base_config_ClientOS=s10u5-x86
base_config_client_allocation="grub"
base_config_products="custom eiscd sds"
base_config_sysidcfg_nameservice=NONE
base_config_sysidcfg_network_interface=PRIMARY
base_config_sysidcfg_ip_address=x.x.x.x
base_config_sysidcfg_netmask=255.255.255.0
base_config_sysidcfg_root_password="XXXXXXXXXXXX"
base_config_sysidcfg_system_locale="en_CA.UTF-8"
base_config_sysidcfg_timeserver=
base_config_sysidcfg_timezone="Canada/Eastern"
base_config_sysidcfg_terminal=vt100
base_config_sysidcfg_security_policy=NONE
base_config_sysidcfg_protocol_ipv6=no
base_config_sysidcfg_default_route=x.x.x.1
I've also tried setting the following:
base_config_sysidcfg_network_interface=PRIMARY
vs
base_config_sysidcfg_network_interface=bge0
I don't mind doing this manually but of course I would much rather have it work automatically.

Try giving more network interface settings in the sysidcfg settings:
network_interface=value {primary hostname=host_name
                          default_route=ip_address or NONE
                          ip_address=ip_address
                          netmask=netmask
                          protocol_ipv6=yes_or_no}
See http://docs.sun.com/app/docs/doc/817-5504/6mkv4nh2r?a=view

AP is unable to associate. The Regulatory Domain '-E' configured on interface '802.11a' does not match the Controller Regulatory Domain '-C'

Hi,
There are three different types of APs associated with controller and working fine.
1.       AIR-LAP1252AG-E-K9
2.       AIR-LAP1522AG-E-K9
3.       AIR-CAP1552E-C-K9
WLC is AIR-CT5508-K9. Software version is 7.4.100.0. Field Recovery Image is 7.0.112.21. Firmware version is FPGA 1.7, Env 1.8, USB console 2.2. WCS is 7.0.240.0 for Windows.
WCS is sending alarms for AIR-LAP1522AG-E-K9:
Message: AP is unable to associate. The Regulatory Domain '-E' configured on interface '802.11a' does not match the Controller Regulatory Domain '-C'.
Before Controller was 7.2.4 (not sure).
Country configured on WLC is AE and shows -CE regulatory domain. Mesh APs are also associated.
I believe this Critical alarm should not come.
how much is this alarm important? What should be done to resolve this?

Typically you still need to make sure that the country codes are indeed configured on the WLC. Thing can change when you upgrade code as standards might of changed and regulations also. If your AP's are functional, then you should be okay and I wouldn't worry too much about it, but if after the upgrade, the WLC complains about country code stuff, then you just need to verify that the AP's country code is defined on the WLC. May times the AP will not join and if it does join, the radios might be disabled or in a down status.
Sent from Cisco Technical Support iPad App

Hi i m using 4s and its updated but i cant configure with microsoft exchange for my gmail account. Anytime i tried to configure it the message comes connection to the server failed. Pls help me out.

Hi i m using 4s and its updated but i cant configure with microsoft exchange for my gmail account. Anytime i tried to configure it the message comes connection to the server failed. Pls help me out.
<Email Edited by Host>

Discontinued by Google. Read here:
http://googlesystem.blogspot.com/2012/12/google-sync-discontinued-for-gmail.html

IP discovery tracking. Cant configure under interface.

Similar Messages

Maybe you are looking for