Is it best to use a basic (ISP supplied) router just as a modem and use the Time Capsule for everything else?

Just feeling my way into using a Time Capsule as the main networking device for two macbooks, two iPhones and occasional vistors including an iPad. Right now the basic ADSL router provides, internet conection, Firewal, DHCP and NAT. The Time Capsule provides WiFI and backup to the MacBooks. The MacBooks and iOS devices all use WiFI and a couple of media devices use ethernet (a hub is part of the network).
Would it be better (i.e. more effective in performance or management) to limit the router as much as possible so for instance turning off DHCP and NAT then reconfiguring the Time Capsule to do that - sort of part way to a situation where the router would be replaced by a modem? Or am I just wasting effort to no good purpose?

There is no simple.. yes or no to your question.
Often modems cannot be bridged.. or if they can the TC does not have the ability to provide the correct services to connect.
What is the broadband type and what is the modem router you are talking about?
Generally the supplied modem is perfectly adequate to the speed capability of the service provided.
In some cases we do say bridge it.. eg alot of cable modem routers supplied here are very poor, Have terrible NAT tables and pathetic abilities.. so we encourage them to be bridged or replaced. Most DSL type modem routers seem to be ok.. and are easily replaced anyway.
Time Capsules are far from being giants in the router world btw.. they have absolute min of controls possible. Lots of good things might be supplied on your normal modem which are missing in the TC. eg QoS. Decent logging, NAT table connection lists.. along with all the other lists.
Overall the gain.. I think for most people will be small.. try it out.. that is the only way to know.

Similar Messages

  • (Cisco Historical Reporting / HRC ) All available connections to database server are in use by other client machines. Please try again later and check the log file for error 5054

    Hi All,
    I am getting an error message "All available connections to database server are in use by other client machines. Please try again later and check the log file for error 5054"  when trying to log into HRC (This user has the reporting capabilities) . I checked the log files this is what i found out 
    The log file stated that there were ongoing connections of HRC with the CCX  (I am sure there isn't any active login to HRC)
    || When you tried to login the following error was being displayed because the maximum number of connections were reached for the server .  We can see that a total number of 5 connections have been configured . ||
    1: 6/20/2014 9:13:49 AM %CHC-LOG_SUBFAC-3-UNK:Current number of connections (5) from historical Clients/Scheduler to 'CRA_DATABASE' database exceeded the maximum number of possible connections (5).Check with your administrator about changing this limit on server (wfengine.properties), however this might impact server performance.
    || Below we can see all 5 connections being used up . ||
    2: 6/20/2014 9:13:49 AM %CHC-LOG_SUBFAC-3-UNK:[DB Connections From Clients (count=5)]|[(#1) 'username'='uccxhrc','hostname'='3SK5FS1.ucsfmedicalcenter.org']|[(#2) 'username'='uccxhrc','hostname'='PFS-HHXDGX1.ucsfmedicalcenter.org']|[(#3) 'username'='uccxhrc','hostname'='PFS-HHXDGX1.ucsfmedicalcenter.org']|[(#4) 'username'='uccxhrc','hostname'='PFS-HHXDGX1.ucsfmedicalcenter.org']|[(#5) 'username'='uccxhrc','hostname'='47BMMM1.ucsfmedicalcenter.org']
    || Once the maximum number of connection was reached it threw an error . ||
    3: 6/20/2014 9:13:49 AM %CHC-LOG_SUBFAC-3-UNK:Number of max connection to 'CRA_DATABASE' database was reached! Connection could not be established.
    4: 6/20/2014 9:13:49 AM %CHC-LOG_SUBFAC-3-UNK:Database connection to 'CRA_DATABASE' failed due to (All available connections to database server are in use by other client machines. Please try again later and check the log file for error 5054.)
    Current exact UCCX Version 9.0.2.11001-24
    Current CUCM Version 8.6.2.23900-10
    Business impact  Not Critical
    Exact error message  All available connections to database server are in use by other client machines. Please try again later and check the log file for error 5054
    What is the OS version of the PC you are running  and is it physical machine or virtual machine that is running the HRC client ..
    OS Version Windows 7 Home Premium  64 bit and it’s a physical machine.
    . The Max DB Connections for Report Client Sessions is set to 5 for each servers (There are two servers). The no of HR Sessions is set to 10.
    I wanted to know if there is a way to find the HRC sessions active now and terminate the one or more or all of that sessions from the server end ? 

    We have had this "PRX5" problem with Exchange 2013 since the RTM version.  We recently applied CU3, and it did not correct the problem.  We have seen this problem on every Exchange 2013 we manage.  They are all installations where all roles
    are installed on the same Windows server, and in our case, they are all Windows virtual machines using Windows 2012 Hyper-V.
    We have tried all the "this fixed it for me" solutions regarding DNS, network cards, host file entries and so forth.  None of those "solutions" made any difference whatsoever.  The occurrence of the temporary error PRX5 seems totally random. 
    About 2 out of 20 incoming mail test by Microsoft Connectivity Analyzer fail with this PRX5 error.
    Most people don't ever notice the issue because remote mail servers retry the connection later.  However, telephone voice mail systems that forward voice message files to email, or other such applications such as your scanner, often don't retry and
    simply fail.  Our phone system actually disables all further attempts to send voice mail to a particular user if the PRX5 error is returned when the email is sent by the phone system.
    Is Microsoft totally oblivious to this problem?
    PRX5 is a serious issue that needs an Exchange team resolution, or at least an acknowledgement that the problem actually does exist and has negative consequences for proper mail flow.
    JSB

  • Can i buy a smaller macbook air (64gb) but use the time capsule for additional data ?

    can i buy a smaller macbook air (64gb) but use the time capsule for additional data ?

    If you plan to store important "original" or "master" files and documents on the Time Capsule, then you might want to think about a way to back up those files to another hard drive.
    Why? If the Time Capsule has a problem...and you have no backups....you lose everything.

  • Can i use the time capsule for storage or just backup?

    I asked my husband to go and buy a separate harddrive so that we could use to store all of our photos on separately as opposed to the computer (as its full and we cant download any more photos!). He came back with the Time Capsule.
    from what i can understand it can only be used for backups and not for direct stoarge - is this correct? Im hoping that i can use it for storage and somehow copy all my photos from my Mac onto the Time Capsule and then we can access them from the network which i just created with the Time Capsule
    Or do i need to buy something else?
    appreciate anyones help
    Thanks

    It is far from ideal. But it does depend on what you are doing. Are you going to store you iphoto library on the TC then it is not recommended.
    Store files on the TC.
    https://discussions.apple.com/message/24380694#24380694
    This is asked several times a day.. obviously people are struggling with their latest SSD being too small.
    The TC is not suitable for network file server.. but many people having no choice press it into service as such.
    It cannot be partitioned. It was and is and ever shall be a backup device for Time Machine.
    Major issues.
    1. No backup.. no way Time Machine can backup a network drive. No place to backup to.. So all your files will be at risk. And you will need to buy a third party like CCC to do backup.
    2. The TC cannot be partitioned and mixing TM backups and data is not great.
    3. The drive is slow to spin up and quick to spin down.. there is no controls.
    4. iPhoto in particular can easily corrupt its entire library with wireless networking causing a disconnection to one photo. Even if you do this;;; do not move your photo library... you have been warned!!
    5. iTunes will constantly lose connection to the library. The disk is too slow to respond.. itunes on the computer will constantly spit out errors. Even in the midst of streaming the TC can spin down the disk due to caching.
    6. Do not use any live files on the TC no matter what else you do.. if you edit files in whatever program the file must be on the local hard disk.
    7. The only suitable location for most libraries is a computer. You can plug in an external hard disk.
    Read pondini for some work arounds.
    Q3 here. http://pondini.org/TM/Time_Capsule.html

  • Can I use a Lenovo laptop with the time capsule for a router?

    Can I use the Time capsule as a wireless router with a lenovo laptop as well as a Mac Book?

    Yes.

  • I want to use the Time Capsule for backup only.

    I picked up a Time Capsule thinking I could use it just for backups. So far, I've been unable to connect to it. I did set it up to extend my current WiFi network, but now I can't see it with Time Machine. What do I do to make the Time Capsule to function just as a wireless back up drive?

    OK, I tried this, what happened is that my iMac lost connection to the Internet while the Ethernet connection was active.
    I said to do this only whilst you setup the TC.. and maybe do the initial backup .. otherwise the idea is to put the TC into the network, which is what you were trying to do.. but obviously do it so that it works.
    As stated, if you bridge the TC.. simply update it.. and plug it into the main router by ethernet. You should now be able to do what you wanted.. connect to it by wireless and use it for backups. The fact that it is linked to the network is absolutely necessary if you want internet at the same time as backups are running. The wireless cannot connect to two different routers at the same time.
    I'd like to know how do I not have it override my Wifi connection and allow me to access the hard drive? If I can't do this, I'll be forced to take the Time Capsule back.
    Please give me exact steps how to setup and use a Time Capsule just as a hard drive. Thanks!
    You only need to do this if you intend to keep the TC connected only to your computer by ethernet, without a network connection.. is that what you want?
    The trick is very simple. Set ethernet manually not by dhcp.. do not set a gateway (router) or DNS for ethernet.
    You can also simply change wifi connection to the top of the list. Both of these are set in the Mac itself not the TC.. the TC can just run as router but with nothing connected.. and ignore the lack of connection.
    The end point of this process though is you have the TC doing what an external hard drive can do, better cheaper and faster. To use the TC as a backup device only connected by ethernet or wireless is a waste.
    Tell me what you want to do.. ie your preferred setup in the light of the previous discussion and I will give you all the screen shots for the exact steps to set that up. I will need to know what IP your current router uses.. and the dhcp range if possible.

  • Can i use new TC to connect wirelessly to home network and plug my tv into the time capsule for internet connectivity?

    My new tv needs to plug into an ethernet port for internet connectivity. 
    I'm hoping it can plug into my TC however my TC is wirelessly connected to my current home network... how can i get this to work?
    TC version A1470 (i think, brand new)
    Many thanks.
    Ben

    If the TC is connected to a wireless network provided by another Apple router, then the TC extends the network by default, and the Ethernet ports are enabled on the TC.
    If the TC is connected to a third party network wirelessly, then it must have been setup to "join" the wireless network. When the TC is set up this way, the TC becomes a wireless hard drive and nothing more. The Ethernet ports are not enabled when the TC "joins" a wireless network.
    So, a logical first troubleshooting step would be to confirm "how" the TC is currently set up. To do that.....assuming that you are using a current or recent version of AirPort Utility on your Mac.......
    Open AirPort Utility
    Click on the TC icon, then click Edit in the smaller window
    Click the Wireless tab at the top of the window
    Check the setting for Network Mode and report on that

  • Internet connection lost using hughesnet modem and Airport in Time Capsule

    I recently got Hughesnet which is the only available high speed internet at my home.
    The problem I'm having is that my wireless connectivity is lost to all devices requiring me to unplug and plug back in my Airport...at which time I have internet again until it goes out again.
    The problem does not appear to be an actual lost internet connection through my Hughesnet modem.
    Any thoughts on how to fix this problem?  I have reset my Airport to factory settings and named it TCwireless for simplicity.
    OS X 10.9.4
    3.2 GHz Intel Core i5
    8 GB 1600 MHz DDR3

    Hey there waltpe,
    Here are a couple of articles for you that will help you troubleshoot the connectivity of your AirPort router:
    Wi-Fi: How to troubleshoot Wi-Fi connectivity
    http://support.apple.com/kb/HT4628
    Wi-Fi Quick Assist
    http://support.apple.com/kb/HT1145
    Thanks for using the Apple Support Communities!
    Cheers,
    Braden

  • Can I use the time capsule for my iPhone or do I need a Mac?

    I want a safe backup for my photos from my iPhone. Is time capsule the right device for this or is it only for Mac's??

    iphone has only one means of backup and that is to itunes..
    itunes in a computer should then be backed up to the TC by Time Machine.. that is the idea..
    Perhaps iphone can also backup to the cloud?? I don't own one so I am not sure.
    If you want to directly copy files to the TC you can load a file app.
    That will work but is not automated.

  • Can i use the computer while backing up with the time capsule for the first time? the

    I would like to install the time capsule. Since it will take some hours to complete the task, do you know if, at the same time, I can work on the computer?
    Thank you.

    Yes, work away.. it might slow down the backup but not significantly.. make sure you do that first backup by ethernet connection though.. it should take less than over night.. so really not that big a deal.

  • As a Verizon FIOS client, can we just use Ethernet cable to connect to time capsule, or do we need their router to connect to the time capsule?

    As a Verizon FIOS client, can we just use Ethernet cable to connect to time capsule or do we need the Verizon router to connect to time capsule?

    The Time Capsule is indeed a wireless router with simultaneous dual band capability...and a hard drive for backup purposes. You can use that to your advantage if you configure the Time Capsule as I suggested in Bridge Mode.
    The Time Capsule will provide a 802.11n 5 GHz band and a 802.11n/g/b compatible 2.4 GHz band to allow virtually any device to connect to the network.
    I suppose that you could also use the "g" wireless network provided by the Verizon router as a "guest" network or something similar if you really do need another wireless network.
    It might be possible to configure the Time Capsule as the main router on the network....that's a question for Verizon. But even if you might be able to do this, I'm sure it is not supported by Verizon, so you would be on your own in the event of any Internet connection difficulties on your service.
    And, since the Time Capsule does not have a built in modem....you would still need to add a separate modem to the installation anyway.
    That's why my suggestion is to use the Verizon device as the "modem" and let the Time Capsule provide the dual band wireless network and of course, handle the Time Machine backups.

  • Best practice to use Time capsule for back-up of 3 different products (MBP 15 OSX lion, MBP 13 OSX lion and MBA 13 OSX mountain lion)?. Only the MBP15 is back-up regularly.

    When I want to save data of the MBA13 on mountain lion (wireless) with time capsule, hois there any best practice to perform?
    After that, assuming that data are back-up, can we easily differentiate data in time capsule belonging to MBP15/13 and MBA13?

    Unfortunately, Apple left off the Ethernet port....the most important port in networking....on the MBA, so your first backup of the entire Mac will need to be done using wireless.
    That may take a day or two unless your MBA has a Thunderbolt port on it in which case you could add a Thunderbolt to Ethernet adapter and connect the MBA to the Time Capsule for the first backup using an Ethernet cable.  It will probably only take 3-4 hours or less doing it this way.
    Once you have the first complete backup done, other subsequent backups can be done using wireless since they will ony take a few minutes, on average.
    Both Macs will backup to the Time Capsule using Time Machine automatically. Backups will be kept completely separate, so one Mac will normally only be able to "see" its own backups.

  • Can I use my time capsule for a hard drive only?

    I have a brand new Time Capsule.
    Instead of backing up all of the time, can I just use the Time Capsule for my music and photos?

    Music and Photos  would be fine.. but not itunes and iphoto.. the libraries are far more complex and if you load it onto the TC you will have no backups.. the TC is a backup device which has no method of backing itself up.

  • Can I use my Time Capsule for wifi parental control?

    Can I use my Time Capsule for WiFi parental control.  The objective first is to use a time clock to control internet access (completely on or off).  Second objective is to use the Time Capsule which is also the WiFi router for more selective internet control?  Anyone out there have any tips on making this work?  We have Time Warner cable feeding the house internet, which is then corrected to the 2Tb Time Capsule which also provides our WiFi.  Any information including other alternatives would be most appreciated.  Surely we are not the only parents on the planet with this issue.  Thanks very much!

    how do I get the Mac addresses for each device (this won't be a problem, I demand the device, check it, and then return it).
    What wireless devices are we looking at here?
    Most devices have the AirPort ID or MAC Address or Hardware Address printed on the back or bottom of the device
    Otherwise, you can learn the correct number by process of elimination. Turn off all wireless devices except your Mac computer....if it is connecting using wireless.
    Open Macintosh HD > Applications > Utilities > AirPort Utility
    Click on the Time Capsule icon
    Look for Wireless Clients and click on the numerical IP address that is displayed
    Another box will open
    Look for the Hardware Address. It will be displayed as xx : xx : xx : xx :xx : xx
    Write that down and note that it is your Mac.
    Now, connect another wireless device and repeat the sequence.  Click on the "other" listing that you see to find out more info about that device.  Write down the ID or Address and note what device it is. Then power it off.
    Do the same for each wireless device that you want to have limited access.
    Post back when you have all the info.

  • I can use my time capsule for wifi, but can't connect for backup

    I have been using my TC for a couple of years now, always as a router and backup disk.  I went on a long trip then came back and tried to connect to it, I can use the wifi, but I can't connect to the disk to see it or use it for backups.  I also have a PC connected to the TC and I can see the contents on there through explorer.
    Any ideas would be appreciated...

    how do I get the Mac addresses for each device (this won't be a problem, I demand the device, check it, and then return it).
    What wireless devices are we looking at here?
    Most devices have the AirPort ID or MAC Address or Hardware Address printed on the back or bottom of the device
    Otherwise, you can learn the correct number by process of elimination. Turn off all wireless devices except your Mac computer....if it is connecting using wireless.
    Open Macintosh HD > Applications > Utilities > AirPort Utility
    Click on the Time Capsule icon
    Look for Wireless Clients and click on the numerical IP address that is displayed
    Another box will open
    Look for the Hardware Address. It will be displayed as xx : xx : xx : xx :xx : xx
    Write that down and note that it is your Mac.
    Now, connect another wireless device and repeat the sequence.  Click on the "other" listing that you see to find out more info about that device.  Write down the ID or Address and note what device it is. Then power it off.
    Do the same for each wireless device that you want to have limited access.
    Post back when you have all the info.

Maybe you are looking for