Is there a way to reverse the direction of video using audio in Motion 3?

Hello all!
Brian here. I have a question. I'm looking to have some music I've written in Logic, to control the actual playback direction of some video footage I've shot. A more visual way of putting this would be like "video scratching". As the audio has scratching in it, I'd like the video clip to reflect the scratching visually. I was wondering if there's a way in Motion 3 to do this. I've looked around, and asked a few people, and I've not gotten any further than having the video's scale (among other things) to bop to the music. Although that's also fun, it's not what I want. If you need more of a visual, check this link:
DJ QBert:
http://www.youtube.com/watch?v=UuL8I0hpkQ4
Watch the needles move around as you hear the scratches, as well as some of the other graphics. It's this effect I'm looking for.
I hope to hear from you all soon!
Sincerely,
Brian.

Try using the Audio parameter behavior applied to the Speed of the clip, that should do it.

Similar Messages

Is there a way to disable the auto play video and audio ads that are showing up on the web these days?

A lot of sites have video ads that load and start playing while safari is loading the entire page - slows everythiing down. Also a couple news sites I go to have autoload/play content. Is there a way to disable these auto loads?

Install the ClickToFlash or ClickToPlugin Safari extension.

I bought about 4 books at once on amazon for my iPad kindle and then realise that I'm not getting round to reading any of them. I've gone into two books but two I haven't. Is there a way of reversing the order and getting my money back?

Hi I bought too many books at once through amazon for my iPad kindle. Havent read any of them and Two I haven't actually gone in to, they have a banner across front which says 'new'is there a way of reversing the transaction either with amazon kindle or the iPad kindle application so I cane my money back?

You should ask Amazon about their returns policy or check the Amazon website. As that's who you bought them from they would be the best people to answer.

I backed up my iphone 4 before updating to my iphone 5 and it restored to default settings. As a result, i have lost all my photos. Is there ant way to reverse the back up as I have a 2 month old baby and desperatly want to retrieve my photos :-(

I backed up my iphone 4 before updating to my iphone 5 and it restored to default settings. As a result, I have lost all my photos. Is there any way to reverse the back up as I have a 2 month old baby and desperatly want to retrieve my photos :-(

Pictures are designed to be copied off the device regularly as would be done with any digital camera. There is no logical reason why anyone would fail to do this with supposedly important pictures.
If a recent backup exists, it is also possible to restore the device from the most recent backup, this may restore pictures to the device. If it does, COPY THEM OFF THE DEVICE IMMEDIATELY for safekeeping.

If I use a sound clip in the multi-track editor multiple times; is there a way to reverse the clip w

If I use a sound clip in the multi-track editor multiple times; is there a way to reverse the clip without change all the instances where the clip was used in the same multi-track session?
I'm having to copy the clip rename it as clipreverses.wav then bring it back into audition to use it.
Sony Vagas you can flip the same clip on a different track with a right click and not affect any other copies of that clip.

Not that I'm aware of, no. You can easily make a unique copy of a clip (right-click on it, and you get it already saved for you), and I'd say that having this was more flexible in one way, at least, as you could then time-stretch it if you wanted to, without altering all other instances of it. Not saying that there wouldn't be any point in having a reverse-play option - I can see instances where it might be useful. It's just that it's not exactly difficult to achieve this anyway, which is probably why I don't ever recall a request for it!

Does anyone know how the cutout filter works and is there a way of achieving the same effect without using filters to get more control over final look?

does anyone know how the cutout filter works and is there a way of achieving the same effect without using filters to get more control over final look?

Several ways to get similar results. Image > Adjustments > Posturize with low values similar to what you'd use n Cutout. This is the most flexible way I can think of as you keep the image in RGB mode with layers intact. A more radical approach would be to reduce bit depth using Indexed Colour. You'll need to experiment with settings, try changing Forced to Primaries, and Matte to Foreground Color. There's no going back from this route, although you can change the mode back to RGB to re-enable layers, adjustment layers etc.
A nice thing about the Filter gallery filters is that you can change the layer to a Smart object with all the control that gives you.
Now if only this forum could filter out bizarre content.

Is there a way to adjust the frame length when using a FFT

Is there a way to adjust the frame length when using a FFT?
Thanks,
David

I thought that to have a longer frame rate you just need to have a longer sample set.

Is there any way to set the SCCM system to use local time instead of UTC?

We have ConfigMgr 2012 in our environment. We are in EST.
Is there any way to set the SCCM system to use local time instead of UTC?
When we try to deploy packages, if you don’t specify the time, it reverts to UTC which for us is off by 5 hours.

Which times are you talking about? Deployment start times or deadlines? Those could be set to UTC *or* client local time.
Torsten Meringer | http://www.mssccmfaq.de

Is there any way to reverse the "swipe to switch between fullscreen apps" controls?

I feel like the "swipe left to go to the app to the left" is actually counter-intuitive, especially when they were thinking about a touchscreen when designing this OS. The scrolling, though most people aren't used to it on a computer, makes sense because you move the page in the direction as if you were moving a physical page. The switching between fullscreen apps is the opposite and isn't natural for me, especially since I have been using an iPhone and iPad for a couple years now. Is there any way of reversing this control? If not, I think they should do the same thing that they did with the "natural" scrolling and have a checkbox to give you the option of either way.

I didn't see anything in the trackpad preferences as far as direction of the swipe. If anyone else can find it, I would love to be able to reverse it.

HT1373 I purchased this product for my Ipad HD and then returned my ipad for a Nexus 10. Is there any way to reverse the charges or move the app to my Nexus 10?

I purchased an IPad HD and downloaded Microsoft Office. Then I returned the IPad and purchased a Nexus 10. Is there any way to dowload the Microsoft Office App to my Nexus 10 without paying again?

No.
The iPad is a superior product - why go to a Nexus?
MJ

Is there a way to reverse the active/inactive portions of the duty cycle?

I'm trying to sync the start times for an AI operation and a buffered encoder read. These two operations happen at different sampling rates and different sampling intervals, so I can't just port the AI scanclock over to the gates of the encoder counters.
My approach is to use three counters: one to generate a triggered pulse that has a width equal to the total sampling time (the trigger for this pulse comes from the AI start). The OUT from this counter then feeds the GATE for a counter that generates a pulse train while the GATE is high. Therefore, it generates a finite pulse train for the desired acquistion time. The out from this second counter goes to the GATEs of the encoder counters to
generate the DMA transfers.
The problem is that the pulse train always puts the active portion of the duty cycle at the end of the period, so the DMA transfer happens at a delay of T/2 relative to the start of the AI acquisition.
Is there a way to put the active portion of the duty cycle at the start of the period? i.e., when the gate goes high, I want the pulse train to start high then go low at the end of the duty cycle.
Thanks,
rgames

The simplest seeming answer would often be to use 'Set Attribute.vi' to change the counter's output polarity. Then the counter will be at a high state during the delay and low during the pulse. However, that would also put it in the high state while armed and waiting for the trigger, and again after the pulse completes. It doesn't seem like that would work for you.
A near-miss idea would be to leave the polarity alone and simply specify the shortest possible delay. Use the internal max timebase as a source and set "Pulse Spec 1" == 2. On a 660x device, that'll only delay you by 25 nsec.
In fact, you may be able to change that near-miss into a perfect hit. The short delay may or may not change the timing of the DMA transfers relative to the trigger, depending on exactly how the "generate pulse train while gate is high" function is implemented. Here are some ways I can imagine:
A. The "pulse while gate is high" counter is always cycling internally. An output signal is always being generated on the TIO chip and is always being AND'ed with the state of the Gate signal coming in. The result of the AND is sent to the actual IO pin.
B. Similar to (A), but the AND'ing is done only when there's a state transition and the result is latched until the next state transition.
C. Internally, the pulse train counter always *wants* to run, but its Source is always being AND'ed with the Gate signal. Then, as far as the pulse train counter is concerned, time is frozen when the Gate is in the inactive state. This is how I *think* I remember it working.
In cases (A) and (B), the timing of the DMA transfers wouldn't be affected except for the rare case where the trigger event occurred within 25 nsec of a "scheduled" transfer. In case (C), you can compensate by changing the duty cycle of the "pulse while Gate is high" counter. Simply subtract 2 from "Pulse Spec 1" and add 2 to "Pulse Spec 2". Then (assuming its polarity is low state delay, high state pulse) make sure the encoder counter Gate is set to do DMA transfers on the low-->high transition.
Final note: if timing synchronization between analog and encoder is really important, there may be a better way. As I recall, the AI start signal does not have deterministic timing relative to the actual A/D conversions. You might instead have two counters of the 660x set to "pulse while Gate is high" and set up the other one to be the AI scan clock. Then you'd be more fully in control of their time==0 marks.

I am hard of hearing, is there some way of boosting the volume especially when using a headset

I am hard of hearing...is there some way of boosting the volume when wearing a headset?

Get an amplified headset.

Is there a way to reverse the Function (Fn) Keys on the ThinkPad T540p and Windwos 8.1?

I recently purchased an I ThinkPad T540p, and install there Windows 8.1 Enterpirse.
Then I download and install all drivers from lenovo site including upgrade BIOS to version 2.07
Then I have noticed that the default for the keys where F1 and F2, etc. usually are, are now the mute and volume buttons. To access the F1, F2....F12 keys, you now have to press Fn + your desired F key.
Is it possible to reverse the Function keys? I would much rather press Fn + F1 to mute than have to press press Fn + F1 to access F1.
Thanks you in advance.
Solved!
Go to Solution.

Hi,
Welcome to Lenovo Community Forums!
Check in BIOS -> config -> Keyboard if there is an option to switch between default and legacy mode.
If you don’t find that option, you may try the Fn+esc combination that changes the function keys to legacy mode, but when the computer reboots, it might reset back to a default mode and you have to use Fn+esc again.
Hope this helps!
Best regards,
Mithun.
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

Is there a way to reverse the order of incoming mail in the new iPad?

I want to reverse the order of incoming mail on my new iPad. I want the oldest on top. I can't seem to find where or even if I can do this. Anyone know for sure? Thanks!

The Mail app only supports having the most recent at the top. You could see if any third-party email apps support it, or access your account via a browser (you can create a Safari shortcut on your iPad's homescreen for your login page).

Is there any way to limit the memory firefox can use?

once firefox reaches about 150Mb of memory it starts locking up and even if I manage to close it through taskmanager it still does not release the memory it was using.Is there any way to set a limit on how much memory firefox can use and a way of making sure it releases it again when shut.I run a dual core 1.8Gb cpu 2 Gb of ram and Win xp Pro service pack 3

See:
* http://kb.mozillazine.org/browser.sessionstore.max_windows_undo
* http://kb.mozillazine.org/browser.sessionstore.max_tabs_undo

Is there a way to reverse the direction of video using audio in Motion 3?

Similar Messages

Maybe you are looking for