ISM with NAT64 - need help with config

Hello,
we are trying to configure NAT64 on ISM. We are running 4.3.0 on ASR9k and all
packages are installed.
Problem is that the config guide is "incomplete" and the NAT64 config is not well
explained.
I will paste the config and show command output..
RP/0/RSP1/CPU0:ASR9010_PE_DMALTA#sh cgn nat64 stateful CGN1 statistics
Tue Jan 29 14:52:59.351 BIH
Unable to obtain requested info Error:'cgn' detected the 'warning' condition 'The instance has not yet been configured'
RP/0/RSP1/CPU0:ASR9010_PE_DMALTA#sh cgn nat64 stateful STATEFULL statistics
Tue Jan 29 14:59:07.270 BIH
Unable to obtain requested info Error:'cgn' detected the 'warning' condition 'CONN state is DOWN'
service cgn CGN1
service-location preferred-active 0/4/CPU0
service-type nat64 stateful STATEFULL
  portlimit 2000
  ipv6-prefix 64:ff9b::/64
  ipv4 address-pool 80.65.84.160/29
  dynamic-port-range start 10000
  address-family ipv4
   interface ServiceApp2
   tcp mss 600
  address-family ipv6
   interface ServiceApp1
   protocol icmp
    reset-mtu
   tcp mss 600
  protocol udp
   timeout 1800
  protocol tcp
   session initial timeout 90
   session active timeout 90
  protocol icmp
   timeout 900
  interface ServiceInfra10
ipv4 address 10.100.127.9 255.255.255.252
service-location 0/4/CPU0
Interface serviceAPP1 is present but not serviceApp2
RP/0/RSP1/CPU0:ASR9010_PE_DMALTA#sh run inter ServiceApp1
Tue Jan 29 22:40:43.814 BIH
interface ServiceApp1
RP/0/RSP1/CPU0:ASR9010_PE_DMALTA#sh run inter ServiceApp2
Tue Jan 29 22:41:34.601 BIH
% No such configuration item(s)
RP/0/RSP1/CPU0:ASR9010_PE_DMALTA#show platform
Tue Jan 29 14:57:29.753 BIH
Node            Type                      State            Config State
0/RSP0/CPU0     A9K-RSP440-TR(Standby)    IOS XR RUN       PWR,NSHUT,MON
0/RSP1/CPU0     A9K-RSP440-TR(Active)     IOS XR RUN       PWR,NSHUT,MON
0/0/CPU0        A9K-8T-L                  IOS XR RUN       PWR,NSHUT,MON
0/1/CPU0        A9K-8T-L                  IOS XR RUN       PWR,NSHUT,MON
0/2/CPU0        A9K-2T20GE-L              IOS XR RUN       PWR,NSHUT,MON
0/3/CPU0        A9K-2T20GE-L              IOS XR RUN       PWR,NSHUT,MON
0/4/CPU0        A9K-ISM-100(LCP)          IOS XR RUN       PWR,NSHUT,MON
0/4/CPU1        A9K-ISM-100(SE)           APP-READY
Package asr9k-ism-cgv6-install-kit-4.3.0.00.sh has been installed!
Node 0/RSP0/CPU0 [RP] [SDR: Owner]
    Boot Device: disk0:
    Boot Image: /disk0/asr9k-os-mbi-4.3.0/0x100305/mbiasr9k-rsp3.vm
    Active Packages:
      disk0:asr9k-fpd-px-4.3.0
      disk0:asr9k-mpls-px-4.3.0
      disk0:asr9k-optic-px-4.3.0
      disk0:asr9k-doc-px-4.3.0
      disk0:asr9k-mini-px-4.3.0
      disk0:asr9k-mcast-px-4.3.0
      disk0:asr9k-mgbl-px-4.3.0
      disk0:asr9k-services-p-px-4.3.0
      disk0:asr9k-k9sec-px-4.3.0
Node 0/4/CPU0 [LC] [SDR: Owner]
    Boot Device: mem:
    Boot Image: /disk0/asr9k-os-mbi-4.3.0/lc/mbiasr9k-lc.vm
    Active Packages:
      disk0:asr9k-mpls-px-4.3.0
      disk0:asr9k-optic-px-4.3.0
      disk0:asr9k-mini-px-4.3.0
      disk0:asr9k-mcast-px-4.3.0
      disk0:asr9k-services-p-px-4.3.0
Service-Engine0/4/0/0          unassigned      Up                    Up    
Service-Mgmt0/4/0/0            unassigned      Up                    Up    
Service-Engine0/4/0/1          unassigned      Up                    Up    
Service-Mgmt0/4/0/1            unassigned      Up                    Up    
Service-Engine0/4/0/2          unassigned      Up                    Up    
Service-Mgmt0/4/0/2            unassigned      Up                    Up    
Service-Engine0/4/0/3          unassigned      Up                    Up    
Service-Mgmt0/4/0/3            unassigned      Up                    Up 

Hi,
first thank your for reply.
hw-module service cgn location 0/4/CPU0 has been typed in the config but I can not see it anywhere in the config after I enter and commit it.
This is the guide I am using. You will see that the NAT64 example is incomplete or is lacking of some explainations. You will see mistakes like an IP address 300.x.x.x . I even tried to completly copy/paste the example in the guide and it still shows the same errors!
http://www.cisco.com/en/US/docs/routers/asr9000/software/asr9k_r4.3/cg_nat/configuration/guide/cgnat_43.html
Edit:
After serviceapp 1 and 2 has been configured the error "Unable to obtain requested info Error:'cgn' detected the 'warning' condition 'CONN state is DOWN'
" has gone
RP/0/RSP1/CPU0:ASR9010_PE_DMALTA#sh run interface serviceapp1
Wed Jan 30 08:44:59.602 BIH
interface ServiceApp1
vrf Internet
ipv6 address 1::1/64
service cgn CGN1 service-type nat64 stateful
RP/0/RSP1/CPU0:ASR9010_PE_DMALTA#sh run interface serviceapp2
Wed Jan 30 08:45:00.950 BIH
interface ServiceApp2
vrf Internet
ipv4 address 1.1.1.1 255.255.255.252
service cgn CGN1 service-type nat64 stateful
RP/0/RSP1/CPU0:ASR9010_PE_DMALTA#sh cgn nat64 stateful STATEFULL statistics
Wed Jan 30 08:46:50.342 BIH
Statistics summary of NAT64 Stateful instance: 'STATEFULL'
Number of active translations                  : 0
Number of static translations                  : 0
Number of dynamic translations                 : 0
Number of Sessions                             : 0
Translations create rate                       : 0
Translations delete rate                       : 0
Inside to outside forward rate                 : 0
Outside to inside forward rate                 : 0
Inside to outside drops port limit exceeded    : 0
Inside to outside drops system limit reached   : 0
Inside to outside drops resource depletion     : 0
No translation entry drops                     : 3134
Filtering Drops                                : 0
Invalid Ipv6 Prefix Drops                      : 0
Number of subscribers                          : 0
Drops due to session db limit exceeded         : 0
Pool address totally free                      : 8
Pool address used                              : 0
For what are the IP addresses in serviceapp used, only for communication between router and ISM?

Similar Messages

  • I need help on Config Master Master Replication

    Hi :
    I got fail on config Master-Master Replica on Directory Server 5.2sp4
    . Can anyone give me some on configuring MMR.
    Error message I got as follows:
    [25/Jul/2006:17:11:17 +0800] - import userRoot: Processed 489736 entries -- average rate 191.8/sec, recent rate 104.7/sec, hit ratio 97%
    [25/Jul/2006:17:11:38 +0800] - import userRoot: Processed 492001 entries -- average rate 191.1/sec, recent rate 105.8/sec, hit ratio 97%
    [25/Jul/2006:17:12:00 +0800] - import userRoot: Processed 494072 entries -- average rate 190.3/sec, recent rate 100.8/sec, hit ratio 97%
    [25/Jul/2006:17:12:22 +0800] - import userRoot: Processed 496657 entries -- average rate 189.7/sec, recent rate 105.8/sec, hit ratio 97%
    [25/Jul/2006:17:12:43 +0800] - import userRoot: Processed 499113 entries -- average rate 189.1/sec, recent rate 114.6/sec, hit ratio 97%
    [25/Jul/2006:17:13:05 +0800] - import userRoot: Processed 501254 entries -- average rate 188.4/sec, recent rate 106.9/sec, hit ratio 97%
    [25/Jul/2006:17:13:08 +0800] - import userRoot: Workers finished; cleaning up...
    [25/Jul/2006:17:13:25 +0800] - import userRoot: Workers cleaned up.
    [25/Jul/2006:17:13:25 +0800] - import userRoot: Indexing complete. Post-processing...
    [25/Jul/2006:17:13:26 +0800] - import userRoot: Flushing caches...
    [25/Jul/2006:17:13:26 +0800] - import userRoot: Closing files...
    [25/Jul/2006:17:13:35 +0800] - import userRoot: Import complete. Processed 501537 entries in 2691 seconds. (186.38 entries/sec)
    [25/Jul/2006:17:13:35 +0800] - INFORMATION - NSMMReplicationPlugin - conn=-1 op=-1 msgId=-1 - multimaster_be_state_change: replica o=tfn.net.tw is coming online; enabling replication
    [25/Jul/2006:17:13:35 +0800] - INFORMATION - NSMMReplicationPlugin - conn=-1 op=-1 msgId=-1 - replica_reload_ruv: Warning: new data for replica o=tfn.net.tw does not match the data in the changelog.
    Recreating the changelog file. This could affect replication with replica's consumers in which case the consumers should be reinitialized.
    [25/Jul/2006:17:13:36 +0800] - INFORMATION - NSMMReplicationPlugin - conn=-1 op=-1 msgId=-1 - This supplier for replica o=tfn.net.tw will immediately start accepting client updates
    [25/Jul/2006:17:13:36 +0800] - INFORMATION - NSMMReplicationPlugin - conn=-1 op=-1 msgId=-1 - Replica (o=tfn.net.tw) has been initialized by total protocol as full replica
    [25/Jul/2006:17:13:36 +0800] - WARNING<10276> - Incremental Protocol - conn=-1 op=-1 msgId=-1 - Replication inconsistency Consumer Replica "ldap1.tfn.net.tw:389/o=tfn.net.tw" has a different data version. It may have not been initialized yet.
    The procedure I did as follows:
    Two LDAP , LDAP1, LDAP2
    1. Install LDAP1 and LDAP2
    2. Migrate Data from old LDAP Server to New LDAP1
    then
    On LDAP1:
    3. Enable Change Log and some parameter
    4. Enable Replication, select "Master"
    5. Create Replication Agreement to LDAP2
    and then
    On LDAP2:
    6. Enable Change Log and some parameter
    7. Enable Replication, select "Master"
    8. Create Replication Agreement to LDAP1
    Now Go back LDAP1
    9. select replication agreement and start initial LDAP2 now.
    10. wait for finished, LDAP1will receive initialiation completed message on startconsole.
    but On LDAP2
    11. check for error log. I got errors.
    [25/Jul/2006:17:13:36 +0800] - WARNING<10276> - Incremental Protocol - conn=-1 op=-1 msgId=-1 - Replication inconsistency Consumer Replica "ldap1.tfn.net.tw:389/o=tfn.net.tw" has a different data version. It may have not been initialized yet.
    Can anyone point out what steps I was wrong ?
    ps: I can't also find the button on procedure 3 mentioned on admin manual.==>
    "To Begin Accepting Updates Through the Console"
    Follow these steps to explicitly allow update operations after the initialization of a multi-master replica:
    3. Click the button to the right of the message to start accepting update
    operations immediately.
    Victor

    1. answer for your last question:
    data server -- configuration -- Data -- your suffix -- Replication
    In right panel, click on the SIR agreement -- click on "Action" on your right low corner -- choose "Send Updates now ..."
    2. answer for your replication question:
    Usually I will move step 2 down before step 9. That means setting up replication first, then feeding your master server using your ldif file: to ldap1, then init ldap2 using data from ldap1, either through Console or through command (if using command, have to use db2ldif -r to dump data from ldap1 and use ldif2db to init ldap2).
    If anytime in your log, you see "different verison of data", try to init again.

  • I Need HELP to config my laptop in France HP's Server URGENT

    Hello,
    i've ben connected to your Site (US HP) and i've make  my desired config in one pavilion DV8, but i live in France and  i can't make this config in HP France (Not this one and others)  i dont ave this possibility here and i need to know why???
    i need to buy my laptop until the begining of the next month... what can i do????? Help me Please.....
    the second question is that i want my laptop in a PT Layout kayboard were can i do that????
    and 3) question i dont want the GT230M graphic card... for my needs i prefere one like HD 5850 or faster and better...
    Can someone help me please or  a responsable for HP products send me for one good way??? please i need all your hel....
    please...
    by....
    URGENT... 

    This is the user forum, and we can't sell you anything. Contact HP through ordinary channels, but I can tell you they can only sell you what they have to sell. There is no special custom configuration of laptops beyond the store checkout available on the web.

  • Need help kernel config M4A785TD-EVO

    Hi,
    My SSD died the other day and I got a replacement (a samsung 840 128Gb). I re-installed but unfortunately I didn't keep a copy of my kernel config file so I am creating a new one but somehow I can't get it to work. I want it without a initrd. I also have an IDE drive (/dev/sda). The SSD is /dev/sdb.
    I get a kernel panic on: Unable to mount root fs on unknown-block(8,18). I don't know what option I'm missing.
    I have:
    Device Drivers
      <*> Serial ATA and Parallel ATA drivers
          <*> ATA SFF support
              <*> ATI PATA support
    Device Drivers
      -*- I2C support
          I2C Hardware Bus support
              <*> Intel PIIX4 and compatible (ATI/AMD/Serverworks/Broadcom/SMSC)
    And also:
    CONFIG_SATA_AHCI=y
    If someone can point me at which option I might be missing that would be great.
    Thanks.

    problem resolved. the default arch sees my ssd as /dev/sdb and the IDE as /dev/sda when my kernel sees it the other way around, the ssd as /dev/sda and the IDE as /dev/sdb.

  • Need help with Berkeley XML DB Performance

    We need help with maximizing performance of our use of Berkeley XML DB. I am filling most of the 29 part question as listed by Oracle's BDB team.
    Berkeley DB XML Performance Questionnaire
    1. Describe the Performance area that you are measuring? What is the
    current performance? What are your performance goals you hope to
    achieve?
    We are measuring the performance while loading a document during
    web application startup. It is currently taking 10-12 seconds when
    only one user is on the system. We are trying to do some testing to
    get the load time when several users are on the system.
    We would like the load time to be 5 seconds or less.
    2. What Berkeley DB XML Version? Any optional configuration flags
    specified? Are you running with any special patches? Please specify?
    dbxml 2.4.13. No special patches.
    3. What Berkeley DB Version? Any optional configuration flags
    specified? Are you running with any special patches? Please Specify.
    bdb 4.6.21. No special patches.
    4. Processor name, speed and chipset?
    Intel Xeon CPU 5150 2.66GHz
    5. Operating System and Version?
    Red Hat Enterprise Linux Relase 4 Update 6
    6. Disk Drive Type and speed?
    Don't have that information
    7. File System Type? (such as EXT2, NTFS, Reiser)
    EXT3
    8. Physical Memory Available?
    4GB
    9. Are you using Replication (HA) with Berkeley DB XML? If so, please
    describe the network you are using, and the number of Replica’s.
    No
    10. Are you using a Remote Filesystem (NFS) ? If so, for which
    Berkeley DB XML/DB files?
    No
    11. What type of mutexes do you have configured? Did you specify
    –with-mutex=? Specify what you find inn your config.log, search
    for db_cv_mutex?
    None. Did not specify -with-mutex during bdb compilation
    12. Which API are you using (C++, Java, Perl, PHP, Python, other) ?
    Which compiler and version?
    Java 1.5
    13. If you are using an Application Server or Web Server, please
    provide the name and version?
    Oracle Appication Server 10.1.3.4.0
    14. Please provide your exact Environment Configuration Flags (include
    anything specified in you DB_CONFIG file)
    Default.
    15. Please provide your Container Configuration Flags?
    final EnvironmentConfig envConf = new EnvironmentConfig();
    envConf.setAllowCreate(true); // If the environment does not
    // exist, create it.
    envConf.setInitializeCache(true); // Turn on the shared memory
    // region.
    envConf.setInitializeLocking(true); // Turn on the locking subsystem.
    envConf.setInitializeLogging(true); // Turn on the logging subsystem.
    envConf.setTransactional(true); // Turn on the transactional
    // subsystem.
    envConf.setLockDetectMode(LockDetectMode.MINWRITE);
    envConf.setThreaded(true);
    envConf.setErrorStream(System.err);
    envConf.setCacheSize(1024*1024*64);
    envConf.setMaxLockers(2000);
    envConf.setMaxLocks(2000);
    envConf.setMaxLockObjects(2000);
    envConf.setTxnMaxActive(200);
    envConf.setTxnWriteNoSync(true);
    envConf.setMaxMutexes(40000);
    16. How many XML Containers do you have? For each one please specify:
    One.
    1. The Container Configuration Flags
              XmlContainerConfig xmlContainerConfig = new XmlContainerConfig();
              xmlContainerConfig.setTransactional(true);
    xmlContainerConfig.setIndexNodes(true);
    xmlContainerConfig.setReadUncommitted(true);
    2. How many documents?
    Everytime the user logs in, the current xml document is loaded from
    a oracle database table and put it in the Berkeley XML DB.
    The documents get deleted from XML DB when the Oracle application
    server container is stopped.
    The number of documents should start with zero initially and it
    will grow with every login.
    3. What type (node or wholedoc)?
    Node
    4. Please indicate the minimum, maximum and average size of
    documents?
    The minimum is about 2MB and the maximum could 20MB. The average
    mostly about 5MB.
    5. Are you using document data? If so please describe how?
    We are using document data only to save changes made
    to the application data in a web application. The final save goes
    to the relational database. Berkeley XML DB is just used to store
    temporary data since going to the relational database for each change
    will cause severe performance issues.
    17. Please describe the shape of one of your typical documents? Please
    do this by sending us a skeleton XML document.
    Due to the sensitive nature of the data, I can provide XML schema instead.
    18. What is the rate of document insertion/update required or
    expected? Are you doing partial node updates (via XmlModify) or
    replacing the document?
    The document is inserted during user login. Any change made to the application
    data grid or other data components gets saved in Berkeley DB. We also have
    an automatic save every two minutes. The final save from the application
    gets saved in a relational database.
    19. What is the query rate required/expected?
    Users will not be entering data rapidly. There will be lot of think time
    before the users enter/modify data in the web application. This is a pilot
    project but when we go live with this application, we will expect 25 users
    at the same time.
    20. XQuery -- supply some sample queries
    1. Please provide the Query Plan
    2. Are you using DBXML_INDEX_NODES?
    Yes.
    3. Display the indices you have defined for the specific query.
         XmlIndexSpecification spec = container.getIndexSpecification();
         // ids
         spec.addIndex("", "id", XmlIndexSpecification.PATH_NODE | XmlIndexSpecification.NODE_ATTRIBUTE | XmlIndexSpecification.KEY_EQUALITY, XmlValue.STRING);
         spec.addIndex("", "idref", XmlIndexSpecification.PATH_NODE | XmlIndexSpecification.NODE_ATTRIBUTE | XmlIndexSpecification.KEY_EQUALITY, XmlValue.STRING);
         // index to cover AttributeValue/Description
         spec.addIndex("", "Description", XmlIndexSpecification.PATH_EDGE | XmlIndexSpecification.NODE_ELEMENT | XmlIndexSpecification.KEY_SUBSTRING, XmlValue.STRING);
         // cover AttributeValue/@value
         spec.addIndex("", "value", XmlIndexSpecification.PATH_EDGE | XmlIndexSpecification.NODE_ATTRIBUTE | XmlIndexSpecification.KEY_EQUALITY, XmlValue.STRING);
         // item attribute values
         spec.addIndex("", "type", XmlIndexSpecification.PATH_EDGE | XmlIndexSpecification.NODE_ATTRIBUTE | XmlIndexSpecification.KEY_EQUALITY, XmlValue.STRING);
         // default index
         spec.addDefaultIndex(XmlIndexSpecification.PATH_NODE | XmlIndexSpecification.NODE_ELEMENT | XmlIndexSpecification.KEY_EQUALITY, XmlValue.STRING);
         spec.addDefaultIndex(XmlIndexSpecification.PATH_NODE | XmlIndexSpecification.NODE_ATTRIBUTE | XmlIndexSpecification.KEY_EQUALITY, XmlValue.STRING);
         // save the spec to the container
         XmlUpdateContext uc = xmlManager.createUpdateContext();
         container.setIndexSpecification(spec, uc);
    4. If this is a large query, please consider sending a smaller
    query (and query plan) that demonstrates the problem.
    21. Are you running with Transactions? If so please provide any
    transactions flags you specify with any API calls.
    Yes. READ_UNCOMMITED in some and READ_COMMITTED in other transactions.
    22. If your application is transactional, are your log files stored on
    the same disk as your containers/databases?
    Yes.
    23. Do you use AUTO_COMMIT?
         No.
    24. Please list any non-transactional operations performed?
    No.
    25. How many threads of control are running? How many threads in read
    only mode? How many threads are updating?
    We use Berkeley XML DB within the context of a struts web application.
    Each user logged into the web application will be running a bdb transactoin
    within the context of a struts action thread.
    26. Please include a paragraph describing the performance measurements
    you have made. Please specifically list any Berkeley DB operations
    where the performance is currently insufficient.
    We are clocking 10-12 seconds of loading a document from dbd when
    five users are on the system.
    getContainer().getDocument(documentName);
    27. What performance level do you hope to achieve?
    We would like to get less than 5 seconds when 25 users are on the system.
    28. Please send us the output of the following db_stat utility commands
    after your application has been running under "normal" load for some
    period of time:
    % db_stat -h database environment -c
    % db_stat -h database environment -l
    % db_stat -h database environment -m
    % db_stat -h database environment -r
    % db_stat -h database environment -t
    (These commands require the db_stat utility access a shared database
    environment. If your application has a private environment, please
    remove the DB_PRIVATE flag used when the environment is created, so
    you can obtain these measurements. If removing the DB_PRIVATE flag
    is not possible, let us know and we can discuss alternatives with
    you.)
    If your application has periods of "good" and "bad" performance,
    please run the above list of commands several times, during both
    good and bad periods, and additionally specify the -Z flags (so
    the output of each command isn't cumulative).
    When possible, please run basic system performance reporting tools
    during the time you are measuring the application's performance.
    For example, on UNIX systems, the vmstat and iostat utilities are
    good choices.
    Will give this information soon.
    29. Are there any other significant applications running on this
    system? Are you using Berkeley DB outside of Berkeley DB XML?
    Please describe the application?
    No to the first two questions.
    The web application is an online review of test questions. The users
    login and then review the items one by one. The relational database
    holds the data in xml. During application load, the application
    retrieves the xml and then saves it to bdb. While the user
    is making changes to the data in the application, it writes those
    changes to bdb. Finally when the user hits the SAVE button, the data
    gets saved to the relational database. We also have an automatic save
    every two minues, which saves bdb xml data and saves it to relational
    database.
    Thanks,
    Madhav
    [email protected]

    Could it be that you simply do not have set up indexes to support your query? If so, you could do some basic testing using the dbxml shell:
    milu@colinux:~/xpg > dbxml -h ~/dbenv
    Joined existing environment
    dbxml> setverbose 7 2
    dbxml> open tv.dbxml
    dbxml> listIndexes
    dbxml> query     { collection()[//@date-tip]/*[@chID = ('ard','zdf')] (: example :) }
    dbxml> queryplan { collection()[//@date-tip]/*[@chID = ('ard','zdf')] (: example :) }Verbosity will make the engine display some (rather cryptic) information on index usage. I can't remember where the output is explained; my feeling is that "V(...)" means the index is being used (which is good), but that observation may not be accurate. Note that some details in the setVerbose command could differ, as I'm using 2.4.16 while you're using 2.4.13.
    Also, take a look at the query plan. You can post it here and some people will be able to diagnose it.
    Michael Ludwig

  • [SOLVED] VIM - need help with keymapping

    As the header says, I need help with creating a key mapping in my vimrc. What I would like is a
    mapping to<F8> that would toggle between " :set paste and :set nopaste. " Any and all help
    would be appreciated
    Last edited by orphius1970 (2010-03-02 07:50:22)

    YES!!!!  Thank you! Exactly what I was hoping for. I am new to vim so all these config options
    are a little intimidating for now. Thank you again!!!!

  • Need help with load balancing and DNS proxy

    Hi,
    I need help on how to configure my router so it will work with my DNS proxy and load balancing.
    I have a Linksys LRT224 router. I have two broadband connections from two separate ISPs,500Mbps each (WAN1 & WAN2). WAN1 has a static IP and WAN2 is dynamic assigned. I use Unlocator (www.unlocator.com) so I can access geographically restricted sites (Pandora, Netflix, etc.).
    The problem I have is that unlocator registers only one IP address (WAN1 address) and since I am doing load balancing I have no way of knowing if the DNS request will go through the registered IP (WAN1) or through the other (WAN2). I am not an expert in routing or networking but I'm guessing I have a way of configuring the router so all the DNS requests go out through WAN1, right?
    In the router's Dual WAN config page there is a section for Protocol Binding. I tried to configure but only managed to screw up the internet at home. I used:
    DNS[UDP/53-53]->192.168.1.1-192.168.1.254(0.0.0.0-0.0.0.0)WAN2
    Any help or suggestions are appreciated.
    Alex

    Good solution though. That's probably the only way you could do true Load Balancing anyway.
    Please remember to Kudo those that help you.
    Linksys
    Communities Technical Support

  • Need help with load balancing and DNS proxy -Repost

    Hi,
    I need help on how to configure my router so it will work with my DNS proxy and load balancing.
    I have a Linksys LRT224 router. I have two broadband connections from two separate ISPs,500Mbps each (WAN1 & WAN2). WAN1 has a static IP and WAN2 is dynamic assigned. I use Unlocator (www.unlocator.com) so I can access geographically restricted sites (Pandora, Netflix, etc.).
    The problem I have is that unlocator registers only one IP address (WAN1 address) and since I am doing load balancing I have no way of knowing if the DNS request will go through the registered IP (WAN1) or through the other (WAN2). I am not an expert in routing or networking but I'm guessing I have a way of configuring the router so all the DNS requests go out through WAN1, right?
    In the router's Dual WAN config page there is a section for Protocol Binding. I tried to configure but only managed to screw up the internet at home. I used:
    DNS[UDP/53-53]->192.168.1.1-192.168.1.254(0.0.0.0-​0.0.0.0)WAN2
    Any help or suggestions are appreciated.
    Alex

    Good solution though. That's probably the only way you could do true Load Balancing anyway.
    Please remember to Kudo those that help you.
    Linksys
    Communities Technical Support

  • Need Help with Installing AP 1250

    I am installing AP 1250 with wireless client authenticating to radius server running on MS ISA server.   The users are supposed to be authenticating with AD.  So far I have been running into problems and unable to get any user connected via Wireless LAN. 
    I would like your feedback if the configuration is good on the AP. Do I need tweak it to work?   The plan is to install one and then install the rest of the 3 more APs in the infrastructure.   I would like to get the one up and running first.  
    I would like any suggestion to enhance my configuration and design guidance.   Also need help for ISA configuration.
    Config from AP
        hostname cisco1-ap
        aaa new-model
        aaa group server radius rad_eap
         server 10.1.2.25 auth-port 1812 acct-port 1813
        aaa group server radius rad_acct
         server 10.1.2.25 auth-port 1812 acct-port 1813
        aaa group server radius rad_admin
        aaa group server tacacs+ tac_admin
        aaa group server radius rad_pmip
        aaa group server radius dummy
        aaa group server radius rad_mac
        aaa authentication login default local
        aaa authentication login eap_methods group rad_eap
        aaa authentication login mac_methods local
        aaa authorization exec default local
        aaa accounting network acct_methods start-stop group rad_acct
        dot11 ssid ABCD123
         authentication open eap eap_methods
         authentication network-eap eap_methods
         authentication key-management wpa
         guest-mode
         infrastructure-ssid optional
        power inline negotiation injector installed
        bridge irb
        interface Dot11Radio0
         no ip address
         no ip route-cache
         encryption mode ciphers tkip
         ssid ABCD123
         station-role root
         rts threshold 2312
         no dot11 extension aironet
         bridge-group 1
        bridge-group 1 subscriber-loop-control
         bridge-group 1 block-unknown-source
         no bridge-group 1 source-learning
         no bridge-group 1 unicast-flooding
         bridge-group 1 spanning-disabled
        interface Dot11Radio1
        shutdown
        interface FastEthernet0
         no ip address
         no ip route-cache
         speed 100
         full-duplex
         bridge-group 1
         no bridge-group 1 source-learning
         bridge-group 1 spanning-disabled
        ip http server
        ip http authentication aaa
        no ip http secure-server
        ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
        ip radius source-interface BVI1
        radius-server attribute 32 include-in-access-req format %h
        radius-server host 10.1.2.25 auth-port 1812 acct-port 1813 key 0 XXX-XXX-XXX-X
        radius-server deadtime 5
        radius-server vsa send accounting
        radius-server vsa send authentication
        bridge 1 route ip
        line con 0
        line vty 0 4

    It is IAS and not ISA server.  I apologies for the confusion it might have caused you. 

  • I REALLY NEED HELP WITH MY CURVE 9300'S WIFI!

    HI !
    i have a blackberry curve 9300, OS5. I got it secondhand. It worked really great, but the problem started when I've done that thing within the host routing table. Though my wifi is connected, I can't use the internet. whenever I tried the BB browser and any other application (e.g. facebook, opera mini, etc.) i get a message that says 'i am not in an area that supports blah blah...' or 'unable to connect to internet please try again later'. I checked the browser under browser config and it is set to my local network provider. i changed it to hotspot browser, saved it. But whenever I go back it also goes back to my local network provider. i have tried almost EVERY troubleshooting I've read on this forums and in other forums but still no luck. The problem worsened when I did a security wipe on the emails, contacts, etc.
    -APN settings are disabled
    -default browser set to hotspot browser
    -firewall disabled
    -data services are on
    Everyone said that it has nothing to do with that activation enterprise so I did not configured it after wiping.
    I also tried doing a hard reboot (pulling the battery out and waiting for 5 minutes before turning it on) but it will only fix the problem for sometime and it will go back again.
    Calling my network provider would just suggest to get a plan when in fact, I was able to use the device's wifi well before without any plan.
    I don't want to upgrade my BB to OS6 coz it easily drains the battery of device and I cannot afford doing that because I go out a lot.
    I also tried changing my sim card and network provider but wasn't successful.
    I also tried deleting the name of my local network provider in the service book under options.
    What do you think could be the problem? Any suggestions? I really, really, REALLY, need help.
    PLEASE ! THANK YOU VERY MUCH IN ADVANCE!

    Hi miochan984,
    Welcome to the support community!
    A supported data plan from your mobile network provider may actually be required to use the Facebook for BlackBerry smartphones application as well as the browser. I would recommend verifying with them which services they support over a Wi-Fi connection without a data plan.
    Let me know if you have any other questions.
    -FS
    Come follow your BlackBerry Technical Team on Twitter! @BlackBerryHelp
    Be sure to click Kudos! for those who have helped you.
    Click Solution? for posts that have solved your issue(s)!

  • I am Stuck! Need Help With Multicast Streaming Using VLC Player

    I have a Multicast network topology shown below
    and my configs
    HUB ROUTER
    no ip domain lookup
    ip domain name primestarhotel.com
    ip multicast-routing
    interface Loopback0
    ip address 5.5.5.5 255.255.255.255
    ip pim sparse-dense-mode
    interface FastEthernet0/0
    ip address 200.0.0.2 255.255.255.240
    ip pim sparse-dense-mode
    ip virtual-reassembly
    speed 100
    full-duplex
    interface FastEthernet0/1.65
    description "Server Vlan"
    encapsulation dot1Q 65
    ip address 10.1.65.1 255.255.255.0
    ip pim sparse-dense-mode
    ip virtual-reassembly
    router ospf 200
    log-adjacency-changes
    network 5.5.5.5 0.0.0.0 area 0
    network 10.1.65.0 0.0.0.255 area 0
    network 200.0.0.0 0.0.0.15 area 0
    ip route 200.1.1.0 255.255.255.252 200.0.0.1
    ip route 200.2.2.0 255.255.255.252 200.0.0.1
    no ip http server
    no ip http secure-server
    ip pim send-rp-announce Loopback0 scope 6
    ip pim send-rp-discovery Loopback0 scope 6
    ISP ROUTER
    interface FastEthernet1/0
    interface FastEthernet1/1
    no switchport
    ip address 200.0.0.1 255.255.255.240
    ip pim sparse-dense-mode
    duplex full
    speed 100
    interface FastEthernet1/2
    no switchport
    ip address 200.1.1.1 255.255.255.252
    ip pim sparse-dense-mode
    duplex full
    speed 100
    interface FastEthernet1/3
    no switchport
    ip address 200.2.2.1 255.255.255.252
    ip pim sparse-dense-mode
    duplex full
    speed 100
    router ospf 200
    log-adjacency-changes
    network 200.0.0.0 0.0.0.15 area 0
    network 200.1.1.0 0.0.0.3 area 0
    network 200.2.2.0 0.0.0.3 area 0
    SPOKE 1 Router
    interface FastEthernet0/0
    ip address 200.1.1.2 255.255.255.252
    ip pim sparse-dense-mode
    speed 100
    full-duplex
    interface FastEthernet0/1
    no ip address
    ip pim sparse-dense-mode
    ip virtual-reassembly
    speed 100
    full-duplex
    interface FastEthernet0/1.12
    description "Workstation pc"
    encapsulation dot1Q 12
    ip address 10.1.12.1 255.255.255.0
    ip pim sparse-dense-mode
    router ospf 200
    log-adjacency-changes
    network 10.1.12.0 0.0.0.255 area 0
    network 200.1.1.0 0.0.0.3 area 0
    ip route 0.0.0.0 0.0.0.0 200.1.1.1
    SPOKE 2
    interface FastEthernet0/0
    ip address 200.2.2.2 255.255.255.252
    ip pim sparse-dense-mode
    speed 100
    full-duplex
    interface FastEthernet0/1
    ip address 10.2.22.1 255.255.255.0
    ip pim sparse-dense-mode
    speed 100
    full-duplex
    router ospf 200
    log-adjacency-changes
    network 10.2.22.0 0.0.0.255 area 0
    network 200.2.2.0 0.0.0.3 area 0
    ip route 0.0.0.0 0.0.0.0 200.2.2.1
    ip route 200.2.2.0 255.255.255.252 200.0.0.1
    I have implemented multicast on the network in a hub and spoke topology. i have set up ospf routing protocol and broadcast all network and can successfully ping.
    I am currently using VLC player as my media streaming server and client. i have set up rtp streaming from the HUb router using multicast ip 224.2.2.2 and unable to broadcast the multicast traffic across the spokes 1 and 2 PC's
    I have never used vlc player  never set up multicast network before and i am struggling with this and need help.
    these are my router configs below
    http://dl.dropbox.com/u/20145606/ip%20video%20config.txt
    Message was edited by: Louis Ojuwu

    I have edited the message and the configs and topology are visible above now. instead of the links i provided

  • [SOLVED]Need help with dwm...

    Hi,
    I need help with dwm.I want to apply only 2 patches but everytime when i try i get error... I need xft or pango patch and systray patch.Please help.
    Thanks.
    Last edited by grobar87 (2013-06-01 13:49:55)

    [dejan@archtop dwm-6.0]$ patch < 00-dwm-6.0-buildflags.diff
    patching file config.mk
    [dejan@archtop dwm-6.0]$ patch < dwm-6.0-xft.diff
    patching file dwm.c
    [dejan@archtop dwm-6.0]$ patch < 02-dwm-6.0-systray.diff
    patching file dwm.c
    [dejan@archtop dwm-6.0]$ sudo make clean install
    [sudo] password for dejan:
    cleaning
    dwm build options:
    CFLAGS = -std=c99 -pedantic -Wall -Os -I. -I/usr/include -I/usr/X11R6/include -I/usr/include/freetype2 -DVERSION="6.0" -DXINERAMA -DXFT
    LDFLAGS = -s -L/usr/lib -lc -L/usr/X11R6/lib -lX11 -L/usr/X11R6/lib -lXinerama -L/usr/X11R6/lib -lXft
    CC = cc
    creating config.h from config.def.h
    CC dwm.c
    dwm.c: In function ‘keypress’:
    dwm.c:1062:2: warning: ‘XKeycodeToKeysym’ is deprecated (declared at /usr/include/X11/Xlib.h:1695) [-Wdeprecated-declarations]
    CC -o dwm
    installing executable file to /usr/local/bin
    installing manual page to /usr/local/share/man/man1
    [dejan@archtop dwm-6.0]$
    And here is my config.h:
    /* See LICENSE file for copyright and license details. */
    /* appearance */
    static const char font[] = "Ohsnap";
    static const char normbordercolor[] = "#444444";
    static const char normbgcolor[] = "#222222";
    static const char normfgcolor[] = "#bbbbbb";
    static const char selbordercolor[] = "#005577";
    static const char selbgcolor[] = "#005577";
    static const char selfgcolor[] = "#eeeeee";
    static const unsigned int borderpx = 1; /* border pixel of windows */
    static const unsigned int snap = 32; /* snap pixel */
    static const unsigned int systrayspacing = 2; /* systray spacing */
    static const Bool showsystray = True; /* False means no systray */
    static const Bool showbar = True; /* False means no bar */
    static const Bool topbar = True; /* False means bottom bar */
    /* tagging */
    static const char *tags[] = { "1", "2", "3", "4", "5", "6", "7", "8", "9" };
    static const Rule rules[] = {
    /* class instance title tags mask isfloating monitor */
    { "Gimp", NULL, NULL, 0, True, -1 },
    { "Firefox", NULL, NULL, 1 << 8, False, -1 },
    /* layout(s) */
    static const float mfact = 0.55; /* factor of master area size [0.05..0.95] */
    static const int nmaster = 1; /* number of clients in master area */
    static const Bool resizehints = True; /* True means respect size hints in tiled resizals */
    static const Layout layouts[] = {
    /* symbol arrange function */
    { "[]=", tile }, /* first entry is default */
    { "><>", NULL }, /* no layout function means floating behavior */
    { "[M]", monocle },
    /* key definitions */
    #define MODKEY Mod1Mask
    #define TAGKEYS(KEY,TAG) \
    { MODKEY, KEY, view, {.ui = 1 << TAG} }, \
    { MODKEY|ControlMask, KEY, toggleview, {.ui = 1 << TAG} }, \
    { MODKEY|ShiftMask, KEY, tag, {.ui = 1 << TAG} }, \
    { MODKEY|ControlMask|ShiftMask, KEY, toggletag, {.ui = 1 << TAG} },
    /* helper for spawning shell commands in the pre dwm-5.0 fashion */
    #define SHCMD(cmd) { .v = (const char*[]){ "/bin/sh", "-c", cmd, NULL } }
    /* commands */
    static const char *dmenucmd[] = { "dmenu_run", "-fn", font, "-nb", normbgcolor, "-nf", normfgcolor, "-sb", selbgcolor, "-sf", selfgcolor, NULL };
    static const char *termcmd[] = { "uxterm", NULL };
    static Key keys[] = {
    /* modifier key function argument */
    { MODKEY, XK_p, spawn, {.v = dmenucmd } },
    { MODKEY|ShiftMask, XK_Return, spawn, {.v = termcmd } },
    { MODKEY, XK_b, togglebar, {0} },
    { MODKEY, XK_j, focusstack, {.i = +1 } },
    { MODKEY, XK_k, focusstack, {.i = -1 } },
    { MODKEY, XK_i, incnmaster, {.i = +1 } },
    { MODKEY, XK_d, incnmaster, {.i = -1 } },
    { MODKEY, XK_h, setmfact, {.f = -0.05} },
    { MODKEY, XK_l, setmfact, {.f = +0.05} },
    { MODKEY, XK_Return, zoom, {0} },
    { MODKEY, XK_Tab, view, {0} },
    { MODKEY|ShiftMask, XK_c, killclient, {0} },
    { MODKEY, XK_t, setlayout, {.v = &layouts[0]} },
    { MODKEY, XK_f, setlayout, {.v = &layouts[1]} },
    { MODKEY, XK_m, setlayout, {.v = &layouts[2]} },
    { MODKEY, XK_space, setlayout, {0} },
    { MODKEY|ShiftMask, XK_space, togglefloating, {0} },
    { MODKEY, XK_0, view, {.ui = ~0 } },
    { MODKEY|ShiftMask, XK_0, tag, {.ui = ~0 } },
    { MODKEY, XK_comma, focusmon, {.i = -1 } },
    { MODKEY, XK_period, focusmon, {.i = +1 } },
    { MODKEY|ShiftMask, XK_comma, tagmon, {.i = -1 } },
    { MODKEY|ShiftMask, XK_period, tagmon, {.i = +1 } },
    TAGKEYS( XK_1, 0)
    TAGKEYS( XK_2, 1)
    TAGKEYS( XK_3, 2)
    TAGKEYS( XK_4, 3)
    TAGKEYS( XK_5, 4)
    TAGKEYS( XK_6, 5)
    TAGKEYS( XK_7, 6)
    TAGKEYS( XK_8, 7)
    TAGKEYS( XK_9, 8)
    { MODKEY|ShiftMask, XK_q, quit, {0} },
    /* button definitions */
    /* click can be ClkLtSymbol, ClkStatusText, ClkWinTitle, ClkClientWin, or ClkRootWin */
    static Button buttons[] = {
    /* click event mask button function argument */
    { ClkLtSymbol, 0, Button1, setlayout, {0} },
    { ClkLtSymbol, 0, Button3, setlayout, {.v = &layouts[2]} },
    { ClkWinTitle, 0, Button2, zoom, {0} },
    { ClkStatusText, 0, Button2, spawn, {.v = termcmd } },
    { ClkClientWin, MODKEY, Button1, movemouse, {0} },
    { ClkClientWin, MODKEY, Button2, togglefloating, {0} },
    { ClkClientWin, MODKEY, Button3, resizemouse, {0} },
    { ClkTagBar, 0, Button1, view, {0} },
    { ClkTagBar, 0, Button3, toggleview, {0} },
    { ClkTagBar, MODKEY, Button1, tag, {0} },
    { ClkTagBar, MODKEY, Button3, toggletag, {0} },

  • Need Help with Packet Loss and routing Loop perhaps???

    Hi,
    I am running into a very odd situation. One of our highly critical systems (172.18.1.2/16) is losing connection intermittently for brief periods of time (1minute, 3 minute, 50 seconds and so on).
    I have gathered some information that I would like to share with you guys:
    The switch is a 3560 (Show version is in ShowVersion.txt)
    default gateway is 172.18.10.254/16 (virtual IP in an HSRP , packet capture is done on the active node)
    I have noticed that pings to one of the default gateways drop infrequently (more frequently from machines on 172.18.0.0/16) segment.
    total number of machines on 172.18.0.0/16 do not exceed 200
    I have captured packets on Interface Vlan1 and I found something very weird, perhaps pointing to a routing loop??? (see capture.png) The ICMP request comes and hits the 172.18.10.254 with TTL of 128 TWICE! then packet capture shows that same packet with TTL decremented by one TWICE! again and again until it reaches TTL of 1 and then it responds with a reply.
    At times it completely ignores the requests and causes a request timed out.
    I am confused and need help in right direction. I really appreciate it.
    can you also confirm if the multiple packets mean routing loop somewhere?
    Thanks

    Could you post a copy of your HRSP config and the results of a #show standby?
    Thanks

  • I got new hard driver for my MacBook I don't have the cd but I do have flash drive that has the software I need help because when I turn on my laptop it shows me a file with question mark how can I install the software from the flash driver?

    I got new hard driver for my MacBook I don't have the cd but I do have flash drive that has the software I need help because when I turn on my laptop it shows me a file with question mark how can I install the software from the flash driver?

    Hold down the Option key while you boot your Mac. Then, it should show you a selection of devices. Click your flash drive and it will boot from that.

  • Installation of Photoshop update 13.1.2 for creative cloud fails with error code U44M1P7 I need help

    I need help installing update 13.1.2 for Photoshop creative cloud, installation fails with error code: U44M1P7. Could someone please help?

    Sorry to bother you.
    I could find the answer after searching previous posts about this language problem.
    Had to change my language in AAM profile and then download PS CS6 again ( english version ).
    Then open the actual Photoshop and in preferences > interface you can besides the Dutch also option for English.
    restart application and Voila.
    Greetz, Jeroen

Maybe you are looking for

  • Can't transfer my ipod tunes to my laptop

    Hi all, just bought a macbook pro, and i took my ipod to put some tunes on it. but it won't let me transfer any of my tunes to my computer! what gives??!?!?!?!

  • Search API for searching Business Objects in SAP R/3

    Hi All, As per my requirement i need to search Business Objects from a third party application by writing some java code. I know only JCO which is useful for to establish a connection from Java to SAP Server and execute the RFC's or BAPI's which are

  • TS3274 My external sound on my iPad comes and goes

    I can plug headphones into my iPad and hear sound but if I unplug headphones you can't hear sound externally. And if you go to the music  app on the iPad to listen to music the area in the upper right corner where you should see volume slider button

  • Use of Bind variables on Transparent Gateway

    Are there any known issues of using bind variables with queries using the Transparent Gateway? I've included two queries that access data from V_PERSON (alias r) which is a SQL Server 2000 table. We're using TG for MSQL 9.0.1 and calling from an Orac

  • Can we write Spel Language Programatically

    Hi All Is it possible to write Spel Language Programatically ? For example , Can I have a code that reads as follows ? Line 1 : OAMessageTextInputBean descBean = (OAMessageTextInputBean)webBean.findChildRecursive("Description"); Line 2: descBean.setR