KT3Ultra and Mobile Athlon XP2400+ possible?
HELP!!!
I just purchased a mobile Athlon XP2400+ for use on my MSI KT3Ultra (via KT333)
and I would like to
A) Get it to work on my board
B) Overclock it
What type of settings should I use? I currently run an XP2100+ Polly stock. Can I leave the stock 1.73 (or 1.65 cant remember) voltage, and increase FSB to 166, ot what?
Am using Crucial PC3200 (512 MB), GF4 Ti 4200 128Meg........
HELP!!!
u prolly wont need this but look here:
https://forum-en.msi.com/index.php?threadid=38822&sid=
make a true sig, amps on psu, an mobile athlon probabley will work
as for overclocking "RESEARCH" its best to see what others have done, and what they have achieved, and how to go about doing it, look at the overclcoking guide at the top of the forum
Similar Messages
-
Need help w/ K7T Turbo2 and mobile Athlon 2600+/266
Hi.
I just bought a new Mobile Athlon 2600+/266 and can't quite get it to work right in my trusty Turbo2. It shows up during post as "Unknow CPU 800MHz", which is a little disappointing. (it is stable at this speed, though) My previous chip in this same board was an Athlon 1200/266 (A1200AMS3C), so everything worked at 133/266 before.
I've updated the BIOS to the most recent, checked that J17 is clear, stripped the box down to cpu + hd + 1 stick ram, and still no dice. All of my CMOS voltage/peripheral settings are at default.
The voltage/frequency menu in the BIOS correctly detects the chipset at 133MHz. When I tried to manually bump the freq multiplier to 15x, I actually saw a decrease in reported processor down to "Unknow CPU 733MHz". When I knocked it down to 14x, it dropped proportionally (to 667, I think). This makes me think that the freq multipler is correct at default, and that it's something else that's going wrong. I don't know what, though.
Is the problem that the chip is Mobile? My last guess is to try to up the voltage, but I didn't want to melt anything before checking with some experts.
I'm not looking for overclocking, just to get it running the 2.133 GHz that it was advertised at.
Thanks much,
-Clint
System specs:
Mobile AMD 2600+/266
K7T Turbo2 (latest BIOS)
ANTEC 350W model PP-352X
2x Micron 256MB PC133 (48lc32m4a2)Does that board have a BIOS setting for FSB, as well as having the J17 jumper? I know a couple people with those boards, but never played in the BIOS to see. It sounds like it is actually trying to use 66MHz X 14, 15 or whatever Multiplier you are setting. Those Mobile chips are not Multi-locked like the normal CPUs are, and may be next to impossible to get set up on these older boards.
-
MSI mega 180 and mobile athlon xp
Does anyone know if the mega 180 supports mobile athlon xp processors? If they do, that would be great.. a xp-m 2400+ is rated at only 35 watts, which would make it very silent.
if you do a search on this forum for "mobile athlon" there are several threads documenting the laborious process of getting the XP-M cpus to work in mega 180. i personally don't think its worthwhile, but if you can manage it i believe it is worth it.
-
KT880 Delta and Amd Athlon XP Mobile
Does KT880 Delta will work with Athlon XP Mobile? PowerNow! features will work?
(AMI bios)ordinary desktop boards won't support changing multiplier on the fly. only laptop mobos do this. mobile athlons XPs are only popular with overclockers, because of the unlocked multiplier in BIOS. not all mobos support Mobile Athlons though, some modifications may need to be done
however, the Athlon64 cpu's and mobos have "Cool n Quiet" technology, which follows the laptop PowerNow! feature, so when cpu is not heavily worked, the clock speed drops to 800mhz, allowing the CPU to run cooler and allows thermal controlled fans to operate slower i think this would suit you better -
Whom so
I bought an Second in hand iphone 5s from a mobile dealer .The phone shows a message like Activation Required- asking icloud id and password..Is it possible to unlock or
please help me what to do .
<Personal Information Edited by Host>Welcome to the user to User Technical Support Forum provided by Apple.
jepin wrote:
I bought an Second in hand iphone 5s from a mobile dealer .The phone shows a message like Activation Required- asking icloud id and password .Is it possible to unlock or
Activation Lock in iOS 7 > http://support.apple.com/kb/HT5818
The Apple ID and Password that was Originally used to Activate the iDevice is required.
If you cannot get this information from the seller
Removing a device from a previous owner’s account
You need to return the Device for a refund, as you will not be able to re-activate it. -
Question about bluetooth communication between PC and mobile device
I am a newbie of bluetooth communication. This time I need to have connumication between PC and mobile device (mainly mobile phone) by sending strings. PC is acted as server and mobile device act as client.
For using bluetooth in PC, I use bluecove 2.0.1
I have already connected them successfully.
When I want to send strings between them, it is found that it can only do one cycle of communication (client -> server -> client).
For my design, they can communicate multiple times.
I simulate the core class of the system, the performance is fine.
Cound anyone help me to watch the code and give me some advices?
Server Side - ServerBox.java
public class ServerBox implements Runnable {
LocalDevice localDevice;
StreamConnectionNotifier notifier;
ServiceRecord record;
boolean isClosed;
ClientProcessor processor;
CMDProcessor cmd;
MainInterface midlet;
private static final UUID ECHO_SERVER_UUID = new UUID(
"F0E0D0C0B0A000908070605040302010", false);
public ServerBox(MainInterface midlet) {
this.midlet = midlet;
public void run() {
boolean isBTReady = false;
try {
localDevice = LocalDevice.getLocalDevice();
if (!localDevice.setDiscoverable(DiscoveryAgent.GIAC)) {
midlet.showInfo("Cannot set to discoverable");
return;
// prepare a URL to create a notifier
StringBuffer url = new StringBuffer("btspp://");
url.append("localhost").append(':');
url.append(ECHO_SERVER_UUID.toString());
url.append(";name=Echo Server");
url.append(";authorize=false");
// create notifier now
notifier = (StreamConnectionNotifier) Connector.open(url.toString());
record = localDevice.getRecord(notifier);
isBTReady = true;
} catch (Exception e) {
e.printStackTrace();
// nothing to do if no bluetooth available
if (isBTReady) {
midlet.showInfo("Initalization complete. Waiting for connection");
midlet.completeInitalization();
} else {
midlet.showInfo("Initalization fail. Exit.");
return;
// produce client processor
processor = new ClientProcessor();
cmd = new CMDProcessor();
// start accepting connections then
while (!isClosed) {
StreamConnection conn = null;
try {
conn = notifier.acceptAndOpen();
} catch (IOException e) {
// wrong client or interrupted - continue anyway
continue;
processor.addConnection(conn);
// activate the set up of process
public void publish() {
isClosed = false;
new Thread(this).start();
// stop the service
public void cancelService() {
isClosed = true;
midlet.showInfo("Service Terminate.");
midlet.completeTermination();
// inner private class for handling connection and activate connection handling
private class ClientProcessor implements Runnable {
private Thread processorThread;
private Vector queue = new Vector();
private boolean isOk = true;
ClientProcessor() {
processorThread = new Thread(this);
processorThread.start();
public void run() {
while (!isClosed) {
synchronized (this) {
if (queue.size() == 0) {
try {
// wait for new client
wait();
} catch (InterruptedException e) { }
StreamConnection conn;
synchronized (this) {
if (isClosed) {
return;
conn = (StreamConnection) queue.firstElement();
queue.removeElementAt(0);
processConnection(conn);
// add stream connection and notify the thread
void addConnection(StreamConnection conn) {
synchronized (this) {
queue.addElement(conn);
midlet.showInfo("A connection is added.");
notify(); // for wait() command in run()
// receive string
private String readInputString(StreamConnection conn) {
String inputString = null;
try {
DataInputStream dis = conn.openDataInputStream();
inputString = dis.readUTF();
dis.close();
} catch (Exception e) {
e.printStackTrace();
return inputString;
private void sendOutputData(String outputData, StreamConnection conn) {
try {
DataOutputStream dos = conn.openDataOutputStream();
dos.writeUTF(outputData);
dos.close();
} catch (IOException e) {
// process connecion
private void processConnection(StreamConnection conn) {
String inputString = readInputString(conn);
String outputString = cmd.reactionToCMD(inputString);
sendOutputData(outputString, conn);
/* try {
conn.close();
} catch (IOException e) {}*/
midlet.showInfo("Client input: " + inputString + ", successfully received.");
}For "CMDProcessor" , it is the class of message processing before feedback to client.
Client side - ClientBox.java
public class ClientBox implements Runnable, CommandListener{
StringItem result = new StringItem("","");
private DiscoveryAgent discoveryAgent;
private String connString;
private boolean isClosed = false;
private boolean boxReady = false;
StreamConnection conn;
private static final UUID ECHO_SERVER_UUID = new UUID( "F0E0D0C0B0A000908070605040302010", false);
Form process = new Form("Process");
ClientInterface midlet;
public ClientBox(ClientInterface mid){
this.midlet = mid;
process.append(result);
process.addCommand(new Command("Cancel",Command.CANCEL,1));
process.setCommandListener(this);
new Thread(this).start();
public void commandAction(Command arg0, Displayable arg1) {
if(arg0.getCommandType()==Command.CANCEL){
isClosed = true;
midlet.notifyDestroyed();
public synchronized void run() {
LocalDevice localDevice = null;
boolean isBTReady = false;
/* Process Gauge screen */
midlet.displayPage(process);
Gauge g=new Gauge(null,false,Gauge.INDEFINITE,Gauge.CONTINUOUS_RUNNING);
process.append(g);
showInfo("Initalization...");
System.gc();
try {
localDevice = LocalDevice.getLocalDevice();
discoveryAgent = localDevice.getDiscoveryAgent();
isBTReady = true;
} catch (Exception e) {
e.printStackTrace();
if (!isBTReady) {
showInfo("Bluetooth is not avaliable. Please check the device.");
return;
if(!isClosed){
try {
connString = discoveryAgent.selectService(ECHO_SERVER_UUID, ServiceRecord.NOAUTHENTICATE_NOENCRYPT, false);
} catch (BluetoothStateException ex) {
ex.printStackTrace();
else return;
if (connString == null) {
showInfo("Cannot Find Server. Please check the device.");
return;
else showInfo("Can Find Server, stand by for request.");
boxReady = true;
/* True if the clientbox is ready */
public boolean getBoxReady(){
return boxReady;
/* True if the clientbox is closed in run() */
public boolean getIsClosed(){
return isClosed;
public String accessService(String input) {
String output = null;
try {
/* Connect to server */
StreamConnection conn = (StreamConnection) Connector.open(connString);
/* send string */
DataOutputStream dos = conn.openDataOutputStream();
dos.writeUTF(input);
dos.close();
/* receive string */
DataInputStream dis = conn.openDataInputStream();
output = dis.readUTF();
dis.close();
} catch (IOException ex){
showInfo("Fail connect to connect to server.");
return output;
private void showInfo(String s){
StringBuffer sb=new StringBuffer(result.getText());
if(sb.length()>0){ sb.append("\n"); }
sb.append(s);
result.setText(sb.toString());
}Client side - ClientInterface.java
public class ClientInterface extends MIDlet implements Runnable, CommandListener{
private ClientBox cb = new ClientBox(this);
private Form temp = new Form("Temp");
private Command select = new Command("Select", Command.OK, 1);
private Command back = new Command("Back", Command.BACK, 1);
Alert alert;
String[] element;
String out;
List list;
public void run(){
/* Send message and get reply */
out = cb.accessService("Proglist");
element = split(out,",");
/* Use the reply to make list */
list = createList(element[0], List.IMPLICIT, out);
list.addCommand(select);
list.addCommand(back);
list.setCommandListener(this);
Display.getDisplay(this).setCurrent(list);
public void startApp() {
System.gc();
waitForBoxSetUp(); /* Recursively check for clientbox status */
new Thread(this).start();
public void pauseApp() {
public void destroyApp(boolean unconditional) {
notifyDestroyed();
public void displayPage(Displayable d){
Display.getDisplay(this).setCurrent(d);
private void waitForBoxSetUp(){
while(!cb.getBoxReady()){
if(cb.getIsClosed())
notifyDestroyed();
public void commandAction(Command c, Displayable d){
if (c.getCommandType() == Command.OK){
if (d == list){
/* Send the choice to server */
out = cb.accessService(list.getString(list.getSelectedIndex()));
alert = new Alert("Output", "selected = "+out, null, AlertType.ALARM);
alert.setTimeout(2000);
Display.getDisplay(this).setCurrent(alert,list);
if (c.getCommandType() == Command.BACK){
notifyDestroyed();
public void showWarning(String title, String content){
alert = new Alert("Output", "selected = "+list.getString(list.getSelectedIndex()), null, AlertType.ALARM);
alert.setTimeout(3000);
Display.getDisplay(this).setCurrent(alert,list);
private List createList(String name, int type, String message){
List temp;
String[] source = split(message,",") ;
temp = new List(name, type, source, null);
return temp;
private static String[] split(String original,String regex)
int startIndex = 0;
Vector v = new Vector();
String[] str = null;
int index = 0;
startIndex = original.indexOf(regex);
while(startIndex < original.length() && startIndex != -1)
String temp = original.substring(index,startIndex);
v.addElement(temp);
index = startIndex + regex.length();
startIndex = original.indexOf(regex,startIndex + regex.length());
v.addElement(original.substring(index + 1 - regex.length()));
str = new String[v.size()];
for(int i=0;i<v.size();i++)
str[i] = (String)v.elementAt(i);
return str;
}i haven't worked with devices but only with the toolkit emulators;
it definitely is possible...
u have to send the image as a bytestream and receive the image at the jsp end...
and then reconstruct the image.
the Stream classes in J2ME AND J2SE are all u will require.
also the Image class.
i have not done this but i have successfully sent an image frm a jsp and displayed it on the emulator. -
Right way to copy desktop version for tablet and mobile
Watching this video http://tv.adobe.com/watch/muse-feature-tour/adobe-muse-designing-for-mobile-devices/
would seem that copying from the desktop version to tablet or mobile, you copy all the contents (texts, images,slide shows etc..).
But i doesn't work. May I have to totally rebuild manually tablet and mobile versions or is possible copy the entire site and then, if i need , make changes in each release?
many thanks in advanceSad! Could be of great help for us develop the function to automatically copy all the contents.
We would avoid to rebuild the site 3 times and we would re-design only things to change.
Many thanks for your reply -
Can I use a domain for one site and mobile me for a different site?
Can I use a domain for one site and mobile me for a different site?
I have two sites, I would like to have up and I would like to do one through a domain and one through mobileme is this possible?Yes you can. You can use the CNAME method of forwarding for the first site (the top site in iWeb) and use the MMe URL for your account for the other site: http://web.me.com/YourAccount_Name/SiteName/
OT -
Oracle 9I Database, and Mobile Server install history
Dear Oracle technical representative:
This TAR started out as a true request for help in solving installation problems with Oracle 9i Release 2 Enterprise Edition, and Oracle 9i Mobile Server Release 5.0.1, but it has turned into a history of frustration with out of date, laconic, and often incorrect, and misleading documentation. As a software developer, I understand that documentation is always out of date, at least mine is. Nonetheless, I must speak my mind while understanding, and sympathizing with your situation.
I struggled through the documentation, and managed to get everything working. While I was doing that, I wrote down the step by step procedure that I used to get Database, and Mobile Server running. By sharing this rough install history with you, it is my hope that it will help prevent others from experiencing the same difficulties that I have had. It has been my observation that when a user has problems installing a trial software package they give up quickly, and do not purchase a copy. It is thus extremely important that the installation instructions, and quick start guide be accurate, attentive to detail, and well written. The first impression is the one that counts.
The Oracle 9i Lite Installation, and Configuration Guide for Windows NT shipped with Oracle 9i Lite Release 5.0.1 definitely requires, and emergency rewrite. It is terribly out of date, inaccurate, and laconic. My guess is that it is a very sloppy rewrite of poorly written 8i documentation. The Oracle 9i Database Installation Guide for Windows is somewhat better. It however should do a better job informing you that before installing onto a old server the Microsoft Foundation Class (MFC), and VC runtime libraries must be up to date. The history describes the trouble with not having the MFC42.dll at version 6. Another corker is that the default port the installer presents is 2030, and not 1521, and that leads to major confusion in the both the Database, and Mobile Server installs.
Thank you for looking at the history. I hope that it will be of use to you when you update your documentation.
Thomas G. Matney
Mississippi State University
[email protected]
(662)325-2791
TAR for Oracle 9i Release 2 Database Enterprise Edition, and Oracle Lite Release 5.0.1 Mobile Server
Installation problems are highlighted in red.
Installation sequence/history:
1. Installed Windows NT 4.0 Server SP1 on Dell Power Edge 4300 dual x86 server to wipe the slate clean.
2. Setup TCP/IP, and IPX/SPX networks
Computer name YGGDRASILL
Host name = YGGDRASILL
Domain = CFR.MSSTATE.EDU
Internet name = YGGDRASILL.CFR.MSSATE.EDU = 130.18.130.225
3. Installed NT SP3, and Internet Explorer 4.01 from the NT 40 Options Pack CD as the gateway to installing MTS 2.0, and IIS 4.0.
4. Installed MTS 2.0, and IIS 4.0 from NT 4.0 Optins Pack CD.
5. Applied NT 4.0 SP6.
6. Installed Internet Explorer 5.5 as a prerequisite to installing MADAC 2.6.
7. Installed MDAC 2.6
8. Installed Paint Shop Pro 7 for capturing error screens.
9. As previous install errors stated that the ordinal function xxxx could not be found in MFC42.dll, the latest version (6.0.8665.0) of the dll was installed, and registered from MS VC++ SP5. Also I upgraded MSVCIRT.dll, MSVCRT.dll, MSCRT40.dll, and added MSVC60.dll from SP5 to be on the safe side.
According to the installation documents all the prerequisites for installing Oracle 9i Release 2 Database Enterprise Edition are satisfied.
10. Began install of Oracle Database Enterprise Edition with target parameters:
Home directory = D:\Oracle\Ora92
Database directory = D:\Oracle\oradata
Global database name = FIA.YGGDRASILL.CFR.MSSTATE.EDU
Port = 2030
SID = FIA
SYSTEM Password = phwphw
SYS Password = phwphw
SCOTT Password = phwphw
DBSNMP Password = I left this one unassigned or empty.
tnsnames.ora entry for remote TCP/IP connection
a. CD 1 of 3 load
1. Error writting to MFC42u.dll. Action ignore. A check indicated that MFC42u.dll version did not match the updated version of MFC42.dll. Plan is to update after install. Unicode version of MFC is probably not used by the installer.
b. CD 1 completed with only one problem, and CD 2 load begins.
c. CD 2 installed without incident., and CD 3 load begins, and completes without farther problems. The only issue to address at this time is to update the MFC42u.dll.
HTTP Server URLs
http://7778
https://4443
12. Evaluation of install success begins.
a. Oracle HTTP Service will not start. It is of particular interest that on installs that I do not upgrade the MFC42.dll the Oracle HTTP Service will start correctly, but during the install I get the error message Ordinal nnnn not found in MFC42.dll, and the Oracle MTS Recovery Service crashes during the install. I am caught between a rock and hard spot on this one. See the Figure 1. At the end of this document. I do not need the HTTP Server at this time but I will need it later and this issue must be resolved. It appears that it hangs during startup. I am sorry but I lost the ordinal number nnnn.
When I try to start the HTTP server from the Programs menu. It Hangs, and does not return an error message. See Figure 2, and the included Apache Setup.txt, the install log, and the HTTPd.conf . The conf, and setup files look OK to me. What is the problem?
b. All other services start correctly.
c. Logged into the database as SCOTT on the server with SQL Plus using the connection information:
FIA.CFR.MSSTATE.EDU =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = TCP)(HOST = yggdrasill)(PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = FIA.YGGDRASILL.CFR.MSSTATE.EDU)
I created some tables, inserted data, and queried for the data. Everthing seems to be working correctly.
d. Logged in remotely from my AOL account on a dial-up line using Oracle 9i Release 2 Personal Edition installed on my ThinkPad. Every thing tested out as above. I used the connection information:
FIA.CFR.MSSTATE.EDU =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = TCP)(HOST = yggdrasill.cfr.msstate.edu)(PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = FIA.YGGDRASILL.CFR.MSSTATE.EDU)
13. I concluded that except for the Oracle HTTP Server Service not starting correctly, and that after updating the MFC42u.dll to VC++ SP5 level the stage is set for installing Oracle 9i Mobile Server Release 5.0.1. I copied the MFC42u.dll to the server and registered it successfully.
14. As Visual Studio 6.0 Professional updates all of the MFC stuff, I decides to install it at this juncture, and apply SP5.
15. Installed JDK1.3.1 required for Oracle 9i Mobile Server Release 5.0.1
At this time the prerequisites for installing Oracle 9i Mobile Server Release 5.0.1 are satisfied, and MFC, and rt are at version 6.
It is important to note that after installing MS Visual Studio Professional 6.0 SP5, the HTTP server started working. It is clear that prior to installing Oracle Database it is essential that MFC, and possibly other components are upgraded before starting an installation of Oracle. This probably only applies to old NT servers, but it should be mentioned in the installation instructions.
16. Attempt to install Oracle Mobile Server Release 5.0.1
a. File locations Screen
Name: = OraLite501
Path: = D:\OraLite501
b. Select Mobile Server at Installation Screen
c. Mobile Server Repository Database Information Screen
Hostname = YGGDRASILL = hostname from tnsnames.ora
Port = 2030 = same as Database port
It is troublesome that the port in tsnames.ora is 1521, and not 2030 as was specified in the database install. I will try this port on the reinstall. On the retry, it worked. The problem was that I was mislead by the default port of 2030 at the database install. The database was actually installed on port 1521, and I was not given an error message, or warning. As I am a first time installer of Oracle products this threw me for a loop. The default port for the database needs to be 1521, if regardless of what the user specifies for a port you are going to install on port 1521.
Net Service Name = FIA.YGGDRASILL.CFR.MSSTATE.EDU = Global database name as required by installation instructions.
d. Yes. At Do you want to install the Mobile Server Repository question.
e. At Oracle Protocol Support, I checked the SPX box.
f. Summary, and Install screens function to specifications.
g. Mobile Server Repository Wizard
Database System password:
Password = phwphw
h. Mobile Server Repository Wizard
Schema Name: fiafield
Password : fiafield
i. Success at last with the install part. The problem was the wrong port number. See my above comments on this problem, and how Oracle could grease the skids for the next first time installer.
j. I could not find the httpd.conf file in the place the install instructions said it should be for running the Mobile Server in Oracle HTTP Server. Since only one copy of httpd.conf existed, I added the include D:\OraLite501\mobile\server\bin\wtgias.conf to the bottom of the file assuming that it is the correct one. I the re-booted instead of using apache -k restart. The Oracle HTTP Server started, so there is hope. The install instructions state that the httpd.conf file would most likely be in the program files directory, when they are really installed in the Oracle Lite home directory.
k. According to the documentation the Mobile Server should start when the Oracle HTTP Server starts with the wtgias.conf file added to the httpd.conf file. It does not. If I use Process Explorer, I know that Apache loaded the wtgias.conf, because both Apache.exe processes that are running have the wtgias.dll loaded. The facts are at this stage of the game are
1. OraMTSRecoveryService is started
2. OracleOraHome92HTTPService is started
3. OracleOraHome92Listener is started on port
4. OracleServiceFIA is started
5. Apache.exe has the wtgias.dll loaded
6. The Moble Server is not running and it should be if the documentation is correct.
7. If I start the Mobile Server either as a service using wtgsvc -i or with the webtogo command from the DOS prompt, the Mobile Server starts, but when I attempt to log in with the URL http://Yggdrasill:7778/webtogo/startup it inform me the Mobile Server is not started and it is. Figure 3 shows the response I receive from the login attempt.
l. I finally ran the Mobile Server in total debug mode using the command webtogo -d0", and it gave me the subtle hint that the correct URL is
http://Yggdrasill.cfr.msstate.edu/webtogo/startup.
When I use the above URL and I can login to the Mobile Server with UN = fiafield, and PW = fiafield. I was confused by the documentation. I was under the assumption that the host address would be either http://Yggdrasill:7778, or http://Yggdrasill:4443. After all when I, installed Oracle Database these URLs were listed. It needs to be made clear in the installation guide for the mobile server that the Mobile Server address is http://Your servers WWW address/webtogo/startup, and the statements about the Mobile Server will start when the Oracle HTTP Server is started needs to be removed since they are incorrect. Also, the documentation should clearly state that the Schema Name, and Password given in the Repository Wizard Screen are synonymous with the username, and password for the Mobile Server login.
m. After determning the hard way that the Mobile Server does not start when the the Oracle HTTP Server starts, and that the correct URL is http://Internet address/webtogo/startup = http://Yggdrasill.cfr.msstate.edu/webtogo/startup, I decide to start the Mobile Server as a service with the command wtgsvc -i. After I re-booted, to my surprise, I could not login to the Mobile Server. When I checked the system services, the webtogo service was running. So to give the start as a service thing a fair chance I re-booted again, but obtained the same results. I thus concluded that the Mobile Server will not run correctly as a service. As it turns out my conclusion was wrong. After waiting a few minutes, my login try was successful. The documentation should indicate that after booting it may be a minute or two before the Mobile Server service become available.
n. After some serious problems with the installer, and the documentation everything is working. I have a green light to go on to the next stage, which is program the handheld to take advantage of the Mobile Server. I will be glad to get back to programming, and am so thankful that I am not a network administrator.
Appendix
HTTPd.Conf (Abstract only), Apache Setup.txt,
tsnames.ora, and listener.ora.
HTTPd.conf (Abstract only)
# Based upon the NCSA server configuration files originally by Rob McCool.
# Include the Oracle configuration file for custom settings
include "D:\oracle\ora92\Apache\Apache\conf\oracle_apache.conf"
include "D:\OraLite501\mobile\server\bin\wtgias.conf "
tsnames.ora
# TNSNAMES.ORA Network Configuration File: D:\oracle\ora92\network\admin\tnsnames.ora
# Generated by Oracle configuration tools.
INST1_HTTP.CFR.MSSTATE.EDU =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = TCP)(HOST = yggdrasill)(PORT = 1521))
(CONNECT_DATA =
(SERVER = SHARED)
(SERVICE_NAME = MODOSE)
(PRESENTATION = http://HRService)
FIA.CFR.MSSTATE.EDU =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = TCP)(HOST = yggdrasill)(PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = FIA.YGGDRASILL.CFR.MSSTATE.EDU)
EXTPROC_CONNECTION_DATA.CFR.MSSTATE.EDU =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC0))
(CONNECT_DATA =
(SID = PLSExtProc)
(PRESENTATION = RO)
listener.ora
# LISTENER.ORA Network Configuration File: D:\oracle\ora92\network\admin\listener.ora
# Generated by Oracle configuration tools.
LISTENER =
(DESCRIPTION_LIST =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC0))
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = TCP)(HOST = yggdrasill)(PORT = 1521))
SID_LIST_LISTENER =
(SID_LIST =
(SID_DESC =
(SID_NAME = PLSExtProc)
(ORACLE_HOME = D:\oracle\ora92)
(PROGRAM = extproc)
(SID_DESC =
(GLOBAL_DBNAME = FIA.YGGDRASILL.CFR.MSSTATE.EDU)
(ORACLE_HOME = D:\oracle\ora92)
(SID_NAME = FIA)
Apache SetupInfo.txt
The following information is available in:
D:\oracle\ora92\Apache\Apache\setupinfo.txt
The HTTP Server can be accessed using the following URLs:
http://yggdrasill:7778
https://yggdrasill:4443You can find information regarding enabling the iSQLPLUS in the following Oracle manual.
http://download-east.oracle.com/docs/cd/B19306_01/server.102/b14357/ch2.htm -
Database 9i, and Mobile Server install history
Dear Oracle technical representative:
This TAR started out as a true request for help in solving installation problems with Oracle 9i Release 2 Enterprise Edition, and Oracle 9i Mobile Server Release 5.0.1, but it has turned into a history of frustration with out of date, laconic, and often incorrect, and misleading documentation. As a software developer, I understand that documentation is always out of date, at least mine is. Nonetheless, I must speak my mind while understanding, and sympathizing with your situation.
I struggled through the documentation, and managed to get everything working. While I was doing that, I wrote down the step by step procedure that I used to get Database, and Mobile Server running. By sharing this rough install history with you, it is my hope that it will help prevent others from experiencing the same difficulties that I have had. It has been my observation that when a user has problems installing a trial software package they give up quickly, and do not purchase a copy. It is thus extremely important that the installation instructions, and quick start guide be accurate, attentive to detail, and well written. The first impression is the one that counts.
The Oracle 9i Lite Installation, and Configuration Guide for Windows NT shipped with Oracle 9i Lite Release 5.0.1 definitely requires, and emergency rewrite. It is terribly out of date, inaccurate, and laconic. My guess is that it is a very sloppy rewrite of poorly written 8i documentation. The Oracle 9i Database Installation Guide for Windows is somewhat better. It however should do a better job informing you that before installing onto a old server the Microsoft Foundation Class (MFC), and VC runtime libraries must be up to date. The history describes the trouble with not having the MFC42.dll at version 6. Another corker is that the default port the installer presents is 2030, and not 1521, and that leads to major confusion in the both the Database, and Mobile Server installs.
Thank you for looking at the history. I hope that it will be of use to you when you update your documentation.
Thomas G. Matney
Mississippi State University
[email protected]
(662)325-2791
TAR for Oracle 9i Release 2 Database Enterprise Edition, and Oracle Lite Release 5.0.1 Mobile Server
Installation problems are highlighted in red.
Installation sequence/history:
1. Installed Windows NT 4.0 Server SP1 on Dell Power Edge 4300 dual x86 server to wipe the slate clean.
2. Setup TCP/IP, and IPX/SPX networks
Computer name YGGDRASILL
Host name = YGGDRASILL
Domain = CFR.MSSTATE.EDU
Internet name = YGGDRASILL.CFR.MSSATE.EDU = 130.18.130.225
3. Installed NT SP3, and Internet Explorer 4.01 from the NT 40 Options Pack CD as the gateway to installing MTS 2.0, and IIS 4.0.
4. Installed MTS 2.0, and IIS 4.0 from NT 4.0 Optins Pack CD.
5. Applied NT 4.0 SP6.
6. Installed Internet Explorer 5.5 as a prerequisite to installing MADAC 2.6.
7. Installed MDAC 2.6
8. Installed Paint Shop Pro 7 for capturing error screens.
9. As previous install errors stated that the ordinal function xxxx could not be found in MFC42.dll, the latest version (6.0.8665.0) of the dll was installed, and registered from MS VC++ SP5. Also I upgraded MSVCIRT.dll, MSVCRT.dll, MSCRT40.dll, and added MSVC60.dll from SP5 to be on the safe side.
According to the installation documents all the prerequisites for installing Oracle 9i Release 2 Database Enterprise Edition are satisfied.
10. Began install of Oracle Database Enterprise Edition with target parameters:
Home directory = D:\Oracle\Ora92
Database directory = D:\Oracle\oradata
Global database name = FIA.YGGDRASILL.CFR.MSSTATE.EDU
Port = 2030
SID = FIA
SYSTEM Password = phwphw
SYS Password = phwphw
SCOTT Password = phwphw
DBSNMP Password = I left this one unassigned or empty.
tnsnames.ora entry for remote TCP/IP connection
a. CD 1 of 3 load
1. Error writting to MFC42u.dll. Action ignore. A check indicated that MFC42u.dll version did not match the updated version of MFC42.dll. Plan is to update after install. Unicode version of MFC is probably not used by the installer.
b. CD 1 completed with only one problem, and CD 2 load begins.
c. CD 2 installed without incident., and CD 3 load begins, and completes without farther problems. The only issue to address at this time is to update the MFC42u.dll.
HTTP Server URLs
http://7778
https://4443
12. Evaluation of install success begins.
a. Oracle HTTP Service will not start. It is of particular interest that on installs that I do not upgrade the MFC42.dll the Oracle HTTP Service will start correctly, but during the install I get the error message Ordinal nnnn not found in MFC42.dll, and the Oracle MTS Recovery Service crashes during the install. I am caught between a rock and hard spot on this one. See the Figure 1. At the end of this document. I do not need the HTTP Server at this time but I will need it later and this issue must be resolved. It appears that it hangs during startup. I am sorry but I lost the ordinal number nnnn.
When I try to start the HTTP server from the Programs menu. It Hangs, and does not return an error message. See Figure 2, and the included Apache Setup.txt, the install log, and the HTTPd.conf . The conf, and setup files look OK to me. What is the problem?
b. All other services start correctly.
c. Logged into the database as SCOTT on the server with SQL Plus using the connection information:
FIA.CFR.MSSTATE.EDU =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = TCP)(HOST = yggdrasill)(PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = FIA.YGGDRASILL.CFR.MSSTATE.EDU)
I created some tables, inserted data, and queried for the data. Everthing seems to be working correctly.
d. Logged in remotely from my AOL account on a dial-up line using Oracle 9i Release 2 Personal Edition installed on my ThinkPad. Every thing tested out as above. I used the connection information:
FIA.CFR.MSSTATE.EDU =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = TCP)(HOST = yggdrasill.cfr.msstate.edu)(PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = FIA.YGGDRASILL.CFR.MSSTATE.EDU)
13. I concluded that except for the Oracle HTTP Server Service not starting correctly, and that after updating the MFC42u.dll to VC++ SP5 level the stage is set for installing Oracle 9i Mobile Server Release 5.0.1. I copied the MFC42u.dll to the server and registered it successfully.
14. As Visual Studio 6.0 Professional updates all of the MFC stuff, I decides to install it at this juncture, and apply SP5.
15. Installed JDK1.3.1 required for Oracle 9i Mobile Server Release 5.0.1
At this time the prerequisites for installing Oracle 9i Mobile Server Release 5.0.1 are satisfied, and MFC, and rt are at version 6.
It is important to note that after installing MS Visual Studio Professional 6.0 SP5, the HTTP server started working. It is clear that prior to installing Oracle Database it is essential that MFC, and possibly other components are upgraded before starting an installation of Oracle. This probably only applies to old NT servers, but it should be mentioned in the installation instructions.
16. Attempt to install Oracle Mobile Server Release 5.0.1
a. File locations Screen
Name: = OraLite501
Path: = D:\OraLite501
b. Select Mobile Server at Installation Screen
c. Mobile Server Repository Database Information Screen
Hostname = YGGDRASILL = hostname from tnsnames.ora
Port = 2030 = same as Database port
It is troublesome that the port in tsnames.ora is 1521, and not 2030 as was specified in the database install. I will try this port on the reinstall. On the retry, it worked. The problem was that I was mislead by the default port of 2030 at the database install. The database was actually installed on port 1521, and I was not given an error message, or warning. As I am a first time installer of Oracle products this threw me for a loop. The default port for the database needs to be 1521, if regardless of what the user specifies for a port you are going to install on port 1521.
Net Service Name = FIA.YGGDRASILL.CFR.MSSTATE.EDU = Global database name as required by installation instructions.
d. Yes. At Do you want to install the Mobile Server Repository question.
e. At Oracle Protocol Support, I checked the SPX box.
f. Summary, and Install screens function to specifications.
g. Mobile Server Repository Wizard
Database System password:
Password = phwphw
h. Mobile Server Repository Wizard
Schema Name: fiafield
Password : fiafield
i. Success at last with the install part. The problem was the wrong port number. See my above comments on this problem, and how Oracle could grease the skids for the next first time installer.
j. I could not find the httpd.conf file in the place the install instructions said it should be for running the Mobile Server in Oracle HTTP Server. Since only one copy of httpd.conf existed, I added the include D:\OraLite501\mobile\server\bin\wtgias.conf to the bottom of the file assuming that it is the correct one. I the re-booted instead of using apache -k restart. The Oracle HTTP Server started, so there is hope. The install instructions state that the httpd.conf file would most likely be in the program files directory, when they are really installed in the Oracle Lite home directory.
k. According to the documentation the Mobile Server should start when the Oracle HTTP Server starts with the wtgias.conf file added to the httpd.conf file. It does not. If I use Process Explorer, I know that Apache loaded the wtgias.conf, because both Apache.exe processes that are running have the wtgias.dll loaded. The facts are at this stage of the game are
1. OraMTSRecoveryService is started
2. OracleOraHome92HTTPService is started
3. OracleOraHome92Listener is started on port
4. OracleServiceFIA is started
5. Apache.exe has the wtgias.dll loaded
6. The Moble Server is not running and it should be if the documentation is correct.
7. If I start the Mobile Server either as a service using wtgsvc -i or with the webtogo command from the DOS prompt, the Mobile Server starts, but when I attempt to log in with the URL http://Yggdrasill:7778/webtogo/startup it inform me the Mobile Server is not started and it is. Figure 3 shows the response I receive from the login attempt.
l. I finally ran the Mobile Server in total debug mode using the command webtogo -d0", and it gave me the subtle hint that the correct URL is
http://Yggdrasill.cfr.msstate.edu/webtogo/startup.
When I use the above URL and I can login to the Mobile Server with UN = fiafield, and PW = fiafield. I was confused by the documentation. I was under the assumption that the host address would be either http://Yggdrasill:7778, or http://Yggdrasill:4443. After all when I, installed Oracle Database these URLs were listed. It needs to be made clear in the installation guide for the mobile server that the Mobile Server address is http://Your servers WWW address/webtogo/startup, and the statements about the Mobile Server will start when the Oracle HTTP Server is started needs to be removed since they are incorrect. Also, the documentation should clearly state that the Schema Name, and Password given in the Repository Wizard Screen are synonymous with the username, and password for the Mobile Server login.
m. After determning the hard way that the Mobile Server does not start when the the Oracle HTTP Server starts, and that the correct URL is http://Internet address/webtogo/startup = http://Yggdrasill.cfr.msstate.edu/webtogo/startup, I decide to start the Mobile Server as a service with the command wtgsvc -i. After I re-booted, to my surprise, I could not login to the Mobile Server. When I checked the system services, the webtogo service was running. So to give the start as a service thing a fair chance I re-booted again, but obtained the same results. I thus concluded that the Mobile Server will not run correctly as a service. As it turns out my conclusion was wrong. After waiting a few minutes, my login try was successful. The documentation should indicate that after booting it may be a minute or two before the Mobile Server service become available.
n. After some serious problems with the installer, and the documentation everything is working. I have a green light to go on to the next stage, which is program the handheld to take advantage of the Mobile Server. I will be glad to get back to programming, and am so thankful that I am not a network administrator.
Appendix
HTTPd.Conf (Abstract only), Apache Setup.txt,
tsnames.ora, and listener.ora.
HTTPd.conf (Abstract only)
# Based upon the NCSA server configuration files originally by Rob McCool.
# Include the Oracle configuration file for custom settings
include "D:\oracle\ora92\Apache\Apache\conf\oracle_apache.conf"
include "D:\OraLite501\mobile\server\bin\wtgias.conf "
tsnames.ora
# TNSNAMES.ORA Network Configuration File: D:\oracle\ora92\network\admin\tnsnames.ora
# Generated by Oracle configuration tools.
INST1_HTTP.CFR.MSSTATE.EDU =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = TCP)(HOST = yggdrasill)(PORT = 1521))
(CONNECT_DATA =
(SERVER = SHARED)
(SERVICE_NAME = MODOSE)
(PRESENTATION = http://HRService)
FIA.CFR.MSSTATE.EDU =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = TCP)(HOST = yggdrasill)(PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = FIA.YGGDRASILL.CFR.MSSTATE.EDU)
EXTPROC_CONNECTION_DATA.CFR.MSSTATE.EDU =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC0))
(CONNECT_DATA =
(SID = PLSExtProc)
(PRESENTATION = RO)
listener.ora
# LISTENER.ORA Network Configuration File: D:\oracle\ora92\network\admin\listener.ora
# Generated by Oracle configuration tools.
LISTENER =
(DESCRIPTION_LIST =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC0))
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = TCP)(HOST = yggdrasill)(PORT = 1521))
SID_LIST_LISTENER =
(SID_LIST =
(SID_DESC =
(SID_NAME = PLSExtProc)
(ORACLE_HOME = D:\oracle\ora92)
(PROGRAM = extproc)
(SID_DESC =
(GLOBAL_DBNAME = FIA.YGGDRASILL.CFR.MSSTATE.EDU)
(ORACLE_HOME = D:\oracle\ora92)
(SID_NAME = FIA)
Apache SetupInfo.txt
The following information is available in:
D:\oracle\ora92\Apache\Apache\setupinfo.txt
The HTTP Server can be accessed using the following URLs:
http://yggdrasill:7778
https://yggdrasill:4443When you install the MD Workstation you are opted to choose among different applications i.e. mobile sales, mobile service, mobile system maintenance or authorization management tool. You can there choose the application to install besides the installation of the MD Workstation.
If you want to add application(s) later, you have to choose 'modify' and choose all parts for the MD Workstation plus the applications. If you omit options chosen before when doing the first installation then these will be removed. So be shure to choose ALL relevant things for the application as well as for the MD Workstation.
You can also generate the application from the installed repository, there are several notes on this subject available ('how to generate an application') which are referred to in about any installation guide or note changing the msa coding.
Regards Kai -
Difference between Mobile sales and Mobile Service
Hi All
Can anybody help and explain me what are the major defferences between Mobile Sales and Mobile Service,What are the configuration settings required in Mobile Service,Because we have to start support project for Mobile Service.
Regards
KrishnaHi Krishna,
The difference is Mobile Service is used by field technicians who provide a service to customers. Eg: an engineer who goes out to customer site to fix machinery. They can fill out the deatils on the Mobile Service application. Time spent, parts used etc..
Sales is used by sales reps, who are selling a product.
The configuration is the same for both. In fact its possible to have bothe sales and service installed on the same machine.
Regards,
Gervase -
How to show iMovies in iPhoto (for iTunes to access for AppleTv and mobile)
I have read a few posts on this but cannot find a definitive answer...
If you import movies into iPhoto, iMovies can access them. But if you import into iMovies, it seems iPhoto cannot access them, which means iTunes cannot access them to stream to AppleTV or sync with my iPhone and iPad, as iTunes does not see iMovies.
Because I have a DV Camcorder I have to import my home movies to iMovie which gives me this above problem in that I cannot see them in iPhoto/iTunes/AppleTv.
So am I right in thinking the best way to have all applications see my movies is to export them from iMovie into iPhoto as follows:-
1) Rip to iMovies from the Camcorder
2) Find the files in Finder
3) Import into iPhoto
4) Delete the originals from iMovie
Then I should be able to see the newly imported files in iPhoto in iMovie AND iTunes??
I cant find or think of an alternate solution.
ThanksI've decided to give the following a go...
Basically I originally wanted to use iPhoto for movies and photos so I have them all in one place and because I think Albums, Smartfolders etc. are great. Movies go hand in had with photos of the same event. But I also wanted them in iTunes to sync. with iPad, iPhone and play via Apple TV.
The file sizes from camcorder videos got me thinking I don't really want the massive files in iPhoto/iTunes/AppleTV etc. So have now decided to use iMovie as the library for the original large files, from which I can edit and make some compilations etc. then export those new movies of lower filesize (mp4?) into iPhoto for use with iTunes, Apple TV, iPhone and iPad.
I decided that when I finish importing I may look at putting the iMovie library with original DVs onto an external drive (due to filesize, if this is possible). So when I want to use iMovie to import and edit and make movies I will plug in the external hard drive where they all are, do my stuff, then can unplug and put away. That way I do not need to delete the originals due to filesize (I did not want to have to re-import from the camcorder again in future so do want them stored somewhere).
It also means I dont have every single video I shot in iPhoto, iTunes etc., not all of them are good.
Then my main computer with the iPhoto library has all my created and edited and new format movies to store for use with iTunes, Apple TV etc.
So I think this sounds like a good plan for me.
iMovie -> Original movie library manager (external drive due to filesize)
iPhoto -> Photos and edited movies library manager (Mac drive for AirPlay and mobile sync) -
Activating mobile datanetwork not possible after downloading 3.1.2 software
Hello,
Realy hope someone can help me out here. I just installed the 3.1.2 software on my i phone 3G and now i cant use internet anymore! Everytime i try its giving me the message "mobiel datanetwerk activeren niet mogelijk" wich means activating mobile datanetwork not possible. Realy weird because i didnt change anything other than downloading this software.
Does anyone know how i can solve this?Welcome to the discussions,
can you check your mail using the phone? Can you connect using WIFI? Did you try to switch on airplane mode and turning it off again? -
Deleted Folder within Photoshop Touch (and CCloud). Recovering possible?
Hi,
i have deleted a folder within Photoshop Touch.
Now some more folders and files were deleted also in CreativeCloud.
They weren't archieved.
Could they be recovered to CreativeCloud in any possible way?
I work on Desktop with Windows Vista and mobile with iPhone, iOS 7.1.1.
Thanks for help!I don't think this can be done. PS Touch is a separate app.
Thanks! -
How to get telephone and mobile phone for one partner
Hello Expert,
In VA03, I open one sales order and go into the partner tab. Then I selection one partner and click "Detail" button, one page with partner detailed information will pop up.
In the pop-up window:
There are two fields: Telephone and Mobile Phone.
In my program, I want to get these two information.
I tried to call FM 'ADDR_COMM_GET' by passing address_number(VBPA-ADRNR), table_type('ADTEL'), iv_current_state(SPACE). For some partner, it works, but for others it doesn't work.
Then I find table ADR2 which is used to keep phone infomration. There are two entries in the table. But how can I identity which one is telephone and which one is Mobile phone?
So can any expert help me on how to get the telephone and Mobile Phone of the pop-up page?
Thanks in advance,
Best Regards, Johnny.Read ADR2-TEL_NUMBER where ADDRNUMBER = VBPA-ADRNR and R3_USER = '2' or '3'.
These are the possible values
Telephone is Landline Telephone
1 Telephone is Default Under Landline Telephones
2 Telephone is Mobile Telephone but Not Default Mobile Phone
3 Telephone is Default Mobile Telephone
X Obsolete - No Longer Valid
Maybe you are looking for
-
Hi, I have a report with multiple tabs in selection screen. Say material number is mandatory in the first tab. But we don't need material number in the second tab. But if I want to go to the 2nd tab, i get the error message 'Please enter the material
-
Features i think should be included in future firmware..
Hi In a ideal world, what updates would you like to see to the firmware? I think the time and date on the front springboard would be a welcome addition. The ability to seach through and add radio stations. Also and one of my bigbest niggles with ATV
-
Safari Quit Unexpectedly after new Magic Trackpad
Hello, I have an iMacG5 with Mac OS X Version 10.6.4. I purchased the new Magic Trackpad, updated my software and paired the Trackpad. In order to pair I had to download a fix for the OS because Trackpad was not showing up under System Preferences. R
-
Software Updates - C. Deployment States report
Please help me if I run Software Updates - C. Deployment States report. I am getting compliant, below other status so these status means software updates instated? Then why it is not showing as compliant Installing update(s), successfully installed u
-
I'm getting no sound when I receive a call or text?
I'm getting no sound when I receive a call or text? Any suggestions