Loading windows xp very slow
i have a mac pro desktop and i have install
windows xp on to a second internal harddrive
and take a long time to load windows
around 20min I think that a long time
boot camp drive is format as ntsb
Btw: AMIBIOS 8 and Phoenix...
AMIBIOS 8 Boot Block Beep Codes
1 Insert diskette in floppy drive A:
2 ‘AMIBOOT.ROM’ file not found in root directory of diskette in A:
3 Base Memory error
4 Flash Programming successful
5 Floppy read error
6 Keyboard controller BAT command failed
7 No Flash EPROM detected
8 Floppy controller failure
9 Boot Block BIOS checksum error
10 Flash Erase error
11 Flash Program error
12 ‘AMIBOOT.ROM’ file size error
13 BIOS ROM image mismatch (file layout does not match image present in flash device)
AMIBIOS 8 POST Beep Codes
1 Memory refresh timer error.
2 Parity error in base memory (first 64KB block)
3 Base memory read/write test error
4 Motherboard timer not operational
5 Processor error
6 8042 Gate A20 test error (cannot switch to protected mode)
7 General exception error (processor exception interrupt error)
8 No VGA found or bad video RAM
9 AMIBIOS ROM checksum error
10 CMOS shutdown register read/write error
11 Cache memory test failed
Phoenix BIOS:
http://bioscentral.com/beepcodes/phoenixbeep.htm
Similar Messages
-
Remote Desktop To Windows Server Very Slow
I have OS X 10.6 running on a MBP and a problem that seems to be growing worse over time. I am using Remote Desktop (both CoRD and Microsoft Remote Desktop) to gain access to remote servers. One is a Windows Server 2008, the others are Windows Server 2003. Initially all was fine, but over the last 2 months access to the W2K server has crawled to a halt. Now, when accessing the other servers I'm having the same issue. I have tried different clients for remote access, used different high speed Internet connections (FIOS, a private network) and the result is the same. Very, very slow connections.
I have also tried using a different login on the laptop to no avail.
I booted Windows on my MBP using Parralels Desktop and tried using Windows RDC to the same servers; that works fine. In fact, I can access the servers very quickly using my iPhone's Remote Access software using the same Internet connection (home WiFi) as my MacBook Pro.
So I can only assume it's an issue with OS X 10.6, since different devices using the same Internet connection can make a much faster connection. But I can't find any similar posts on the issue.
Any ideas are appreciated!Hi Jason,
From the error message, it seems that take time to load the user configuration properly from the server and then the network connection was slow. Please refer to following article
and check if help you to troubleshoot slow logon.
Troubleshooting
Slow Logons
Please Note: Since the web site is not hosted by Microsoft, the link may change without notice. Microsoft
does not guarantee the accuracy of this information.
Meanwhile, please refer to following thread and check if can help you.
Remote
Desktop Services has taken too long to load the user configuration from server Event ID 20499
Hope this helps.
Best regards,
Justin Gu -
Windows running very slow and doesnt shut down peoperly
I have to manually press the on/Off button to shut off the computer.
also everything seems to load very slow including windows when I start up my computer.
Is there some free software out there that I can download that might help fix my issue or maybe something I can try to help speed up my computer. I have already run Malwarebytes Anti-Malware / SUPERAntiSpyware Free Edition / disc cleanup /defrag.
"Thanks so much for your help " Butch
WBAYou should repost your problem in the more appropriate Windows Community forums here...
http://answers.microsoft.com/en-us/windows/forum/performance
Noel Paton | Nil Carborundum Illegitemi
CrashFixPC |
The Three-toed Sloth
No - I do not work for Microsoft, or any of its contractors. -
Since installing Parallels 7 and Windows 7 (to use Quicken), my imac and the virtual computer run very slow. Is there a good fix?
Start up while holding Command R and run Disk Utility, check the SMART status and repair your hard drive.
-
Windows 7 very slowed after I downloaded ITunes. could someone help me?
My PC with Windows 7 is very slowed since I downloaded iTunes. Could someone help me? Thank you
All purchases from the iTunes Store including free and paid apps are included in your purchase history which cannot be deleted. Deleting an app from your iTunes library on your computer or on your iPad or iOS device does not remove the app from your purchase history.
You did use iTunes to download the apps or they wouldn't be incldued in your iTunes Store purchase history. -
Internet downloading in windows 7 very slow
hi...
am using windows 7 64bit before i used windows 8.1 delete and install windows 7 64bit now w my downloading internet speed is very very slow... am getting just 1 mbps fast ... but in my laptop am getting more than 40mbps... not in pavilion desktop...
both runs on windows 7 64 bit... but my laptop is sony vaio.....
thats a brand new system i didnt get the proper driver networks from hp for windows also.. then find it and solved it... but my downloading very slow...Hello @vijay79,
I understand that after downgrading to Windows 7 your internet speed has slowed down. What connection type are you using to connect to the internet wired or wireless? Have you ensured that you have installed all the drivers from the HP Pavilion Desktop - 500-400na - Software & Drivers page? If not please do so.
If after you have ensured that all the drivers are installed you still have the slow speed issue please re-post with the answers to my questions and I will be happy to help you further. Thank you for posting on the HP Forums. Have a great day!
Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
Dunidar
I work on behalf of HP
Find out a bit more about me by checking out my profile!
"Customers don’t expect you to be perfect. They do expect you to fix things when they go wrong." ~ Donald Porter -
Loading Page is very slow. Thread dump show "BuildCookie"
Hello, Folks,
I am developing a portal project, which have some pages and books. I find that my page is loaded very slow and I took three times thread dump, the following is the detail of thread dump. Could someone give me some hints that can help me to figure out what needs to be corrected in my code or design?
"ExecuteThread: '14' for queue: 'default'" daemon prio=5 tid=0x03bf5190 nid=0xe2
c runnable [44ce000..44cfd90]
at java.io.WinNTFileSystem.list(Native Method)
at java.io.File.list(File.java:915)
at java.io.File.listFiles(File.java:993)
at com.bea.wlw.runtime.core.dispatcher.AppManager.isExternalBuildCookieV
alid(AppManager.java:1080)
at com.bea.wlw.runtime.core.dispatcher.AppManager.validateExternalBuildC
ookie(AppManager.java:1137)
at com.bea.wlw.runtime.core.dispatcher.AppManager.ensureAppDeployment(Ap
pManager.java:655)
at com.bea.wlw.runtime.core.dispatcher.AppManager.ensureAppDeployment(Ap
pManager.java:575)
at jsp_servlet._framework._skeletons._default.__book._jspService(book.js
p:12)
at weblogic.servlet.jsp.JspBase.service(JspBase.java:33)
at weblogic.servlet.internal.ServletStubImpl$ServletInvocationAction.run
(ServletStubImpl.java:1072)
at weblogic.servlet.internal.ServletStubImpl.invokeServlet(ServletStubIm
pl.java:465)
at weblogic.servlet.internal.ServletStubImpl.invokeServlet(ServletStubIm
pl.java:348)
at weblogic.servlet.internal.RequestDispatcherImpl.include(RequestDispat
cherImpl.java:638)
at weblogic.servlet.internal.RequestDispatcherImpl.include(RequestDispat
cherImpl.java:423)
at com.bea.netuix.servlets.controls.JspRenderer.renderAlt(JspRenderer.ja
va:194)
at com.bea.netuix.servlets.controls.JspRenderer.endRender(JspRenderer.ja
va:142)
at com.bea.netuix.nf.ControlLifecycle$1.postVisit(ControlLifecycle.java:
538)
at com.bea.netuix.nf.ControlTreeWalker.walkRecursiveRender(ControlTreeWa
lker.java:564)
at com.bea.netuix.nf.ControlTreeWalker.walkRecursiveRender(ControlTreeWa
lker.java:553)
at com.bea.netuix.nf.ControlTreeWalker.walkRecursiveRender(ControlTreeWa
lker.java:553)
at com.bea.netuix.nf.ControlTreeWalker.walkRecursiveRender(ControlTreeWa
lker.java:553)
at com.bea.netuix.nf.ControlTreeWalker.walkRecursiveRender(ControlTreeWa
lker.java:553)
at com.bea.netuix.nf.ControlTreeWalker.walkRecursiveRender(ControlTreeWa
lker.java:553)
at com.bea.netuix.nf.ControlTreeWalker.walkRecursiveRender(ControlTreeWa
lker.java:553)
at com.bea.netuix.nf.ControlTreeWalker.walk(ControlTreeWalker.java:247)
at com.bea.netuix.nf.Lifecycle.runOutbound(Lifecycle.java:204)
at com.bea.netuix.nf.Lifecycle.run(Lifecycle.java:146)
at com.bea.netuix.servlets.manager.UIServlet.runLifecycle(UIServlet.java
:333)
at com.bea.netuix.servlets.manager.UIServlet.doPost(UIServlet.java:196)
at com.bea.netuix.servlets.manager.PortalServlet.doPost(PortalServlet.ja
va:772)
at com.bea.netuix.servlets.manager.PortalServlet.doGet(PortalServlet.jav
a:671)
at com.bea.netuix.servlets.manager.UIServlet.service(UIServlet.java:147)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)
at weblogic.servlet.internal.ServletStubImpl$ServletInvocationAction.run
(ServletStubImpl.java:1072)
at weblogic.servlet.internal.ServletStubImpl.invokeServlet(ServletStubIm
pl.java:465)
at weblogic.servlet.internal.TailFilter.doFilter(TailFilter.java:28)
at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.ja
va:27)
at com.bea.p13n.servlets.PortalServletFilter.doFilter(PortalServletFilte
r.java:293)
at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.ja
va:27)
at weblogic.servlet.internal.WebAppServletContext$ServletInvocationActio
n.run(WebAppServletContext.java:6987)
at weblogic.security.acl.internal.AuthenticatedSubject.doAs(Authenticate
dSubject.java:321)
at weblogic.security.service.SecurityManager.runAs(SecurityManager.java:
121)
at weblogic.servlet.internal.WebAppServletContext.invokeServlet(WebAppSe
rvletContext.java:3892)
at weblogic.servlet.internal.ServletRequestImpl.execute(ServletRequestIm
pl.java:2766)
at weblogic.kernel.ExecuteThread.execute(ExecuteThread.java:224)
at weblogic.kernel.ExecuteThread.run(ExecuteThread.java:183)The page is slow because of the VO query.. I have tuned the query... Now its faster....
-
ITunes+Windows 7= Very Slow Music Sync
As above. Everything is perfect, but when i want to sync my music with my iphone 4 or with my ipad it takes forever. Any suggestions ?
I have very slow itunes since SP1, but have found a remarkably easy work round. Start itunes, start what you want to do - like sync to ipod et al, then just click the windows 'show desktop icon' and itunes does the stuff properly!
I have win 7 SP1 2gb 2Ghz AMD -
Greetings.
I'm new on this forum allthough I have had this mobo about ½ year, but when I tried to get Windows 8 Pro upand running I ran into troubble.
Intel Rapid Start don't work in Win8, worked really good in Win7
Can't switch "Windows 8" feature on in BIOS (have read here, that I'm not the only one with that problem)
But my biggest complain is the performance of USB3. I use it for backup, and it is very slow compared to Windows 7. I can't find any USB3 driver on MSI's download. I know ASUS has made an "USB3 BOOST" but I don't know what it is, or if it is helping. Windows 8 has native driversupport for USB3, but it is only to get it to basic work, much much slower than the same USB3 port in Windows 7. Does anyboby know how to raise the USB3 speed?
Sorry for my English. As I'm danish, English is not my first language, but I hope you get the meaning of thisCould well be a driver issue as you mentioned. MSI doesn't make the drivers, they are supplied new ones by the vendor of the hardware. Normally they are tested by the MSI engineers first, certified to be good, and then released on their webite for download. The growing pains of 'Vista' 8 (sarcasm) continue!
-
I recently spilled a slight amount of water on my Mac Book Pro. I thought I was able to remove and wipe the majority of it off but I believe some may have seeped between my keys. Ever since, keys on my keyboard do not work or they type in all caps, my trackpad will select multiple objects when I click once (i.e. I attempt to open an application and it will select 5 applications and open all), when I use my hot corners to move between windows, the window I click on will 'zoom in' a very slow speed.
Could this all be a result of water damage? Or something further?
Please let me know if more information is needed.
Thanks,
PMI recently spilled a slight amount of water on my Mac Book Pro. I thought I was able to remove and wipe the majority of it off but I believe some may have seeped between my keys. Ever since, keys on my keyboard do not work or they type in all caps, my trackpad will select multiple objects when I click once (i.e. I attempt to open an application and it will select 5 applications and open all), when I use my hot corners to move between windows, the window I click on will 'zoom in' a very slow speed.
Could this all be a result of water damage? Or something further?
Please let me know if more information is needed.
Thanks,
PM -
I installed windows ultimate 64 bit, Tried to install firefox for my default browser. Internet explorer loads everything like normal, no problem but firefox will not load or does after 5 mins +
I checked my firewall windows provides and Avira to see if they were blocking, Found nothing of anything being blocked.
This is a fresh installed windows 7, No viruses or malwareStart Firefox in <u>[[Safe Mode]]</u> to check if one of the extensions or if hardware acceleration is causing the problem (switch to the DEFAULT theme: Firefox (Tools) > Add-ons > Appearance/Themes).
*Don't make any changes on the Safe mode start window.
*https://support.mozilla.com/kb/Safe+Mode
A possible cause is security software (firewall) that blocks or restricts Firefox or the plugin-container process without informing you, possibly after detecting changes (update) to the Firefox program.
Remove all rules for Firefox from the permissions list in the firewall and let your firewall ask again for permission to get full unrestricted access to internet for Firefox and the plugin-container process and the updater process.
See:
*https://support.mozilla.com/kb/Server+not+found
*https://support.mozilla.com/kb/Firewalls -
X200 - Windows XP - Very slow in normal day-to-day usage
Hello,
My manager got a brand new x200 laptop about 1.5 years ago. We put Windows XP on it. It has 1.5 GB of RAM.
Not alot of software is on it. Just Office 2003 (back then, recently upgraded to Office 2010). Our office uses Symantec Endpoint Protection.
Since the time of purchase, the laptop has been very sluggish. Opening Outlook (2003 and 2010) takes a few minutes. Opening folders in Windows Explorer has noticeable lag time. Even right-clicking the Start Menu takes almost a minute before the sub-menu appears.
Any ideas why? Thanks for any advice or help!The #1 cause for slow performance on PCs (in my experience) is anti-virus software, endpoint protection software, and encryption software. As an experiment, try uninstalling these things and see if performance improves. You can re-install them again later after your experiment is over.
other things to try:
1. run chkdsk
2. run defrag
3. run HDD diagnostics to see if you have a failing HDD -
Windows 7 very slow logon, Waiting for the User Profile Service, winlogon event 6006
Hello,
Every so often one of our Windows 7 clients which is not normally having any delay at logon will take a very long time to login. This may be 10 or 20 minutes or up to an hour in some cases.
Typically the event log will contain entries like
The winlogon notification subscriber <Profiles> took 572 second(s) to handle the notification event (Logon).
There is no further information available from Event Log Online Help, nor any additional detail as to why the logon event was so slow. During the delay the user will just see "Waiting for the User Profile Service" on their screen.
We first started seeing this problem with Windows Vista and if anything the situation has not improved since then. It has never happened with any of our Windows XP users.
We are currently planning a migration of computers to Windows 7 but stuff like this which has not been resolved in Windows over a 2 year period will stall that migration. The least improvement is to increase the event notification to give a lot more
information on why the user profile processing has stalled.Hi,
When did the issue begin to occur? Did it occur after installing certain application or applying certain policy?
To troubleshoot the issue, please perform the following step.
1. Restart the machine in Safe Mode with Networking to check whether the system can login quicker.
2. Type “gpedit.msc” in Search box and press Enter. Navigate to the following location:
Computer Configuration->Administrative Templates->System->Logon
Please double click “Always wait for the network at computer startup and logon” policy and disable it.
3. Perform a
Clean Boot to check the result.
Thanks,
Novak -
Windows 7 VERY slow browsing and creating folders
Hi!
I'm having a rather strange problem with Windows 7 RC. I've noticed that browsing folders is generally slower than in WinXP, but still acceptable. But lately I'm having a lot of difficulties moving files, creating folders, renaming folders and files, and even waiting for an Explorer window to refresh after some external app has created or modified a file. Sometimes I have to wait up to 30 seconds for a new folder to be created, and another 10 or 15 after I rename it (from "New Folder" to whatever else).
This does not happen in every folder in my HDD, but I don't know exactly in which ones. I thought it was the indexed folders, so I removed a few from the Windows Indexing database, and they were still slow (after system reboot and all). Then I thought it would probably happen in folders that are part of a library, so I removed them and the problem was still there. I can't think of another reason for this to happen in some folders and not others. It seems to happen in my frequently used folders, which honestly sucks.
Just for the record, here's my system's specs:
Dell Inspiron 9400 laptop (e1705), late 2006 model
2GB DDR2 667 ram
320 GB 7200 rpm seagate HDD, aftermarket (really fast drive, not the problem here)
Intel Core Duo (Centrino Duo) 2.0GHZ
Windows 7 RC, multiboot with WinXP
Thanks!!!For the benefit of those who are being driven nuts with SLLOOOWWWW Explorer 'Problems', I list the methodology which has worked for me.
As always, 'Use at Own Risk' and 'Your Mileage May Vary'.
Do NOT repeat NOT perform these steps unless youfully understand the ramifications and are prepared to live with the consequences.
BACKUP FIRST !!! - Create a RESTORE POINT!
The latest incarnations of Windows attempt to 'out-think' the user in order to provide a 'Better Computing Experience', and that is well and good for the average Joe-Blow, but NOT what the Power-User wants or expects. There are MANY suggestions as
to the cause and solution(s) for slow Explorer response, but we have to remember just how much work is going on behind the scenes.
Much of that work is to provide 'pretty' screen enhancements and to make for 'simpler' Searching. By foregoing some of these we can reclaim quite a lot of CPU cycles and Disk I/O for our own (Applications) use.
Before you embark on any changes, carefully assess just how you use your PC. - How important are Thumbnails? - What value does Content View really provide? - Can you implement a Folder structure and File-Naming convention which makes Snippets and Content
indexing of little use?
You'll still be able to see local thumbnails if that's what you want, they will just be remade each time you open the folder and select Thumbnail (Large Icon) View. This is usually less bothersome than the time loss of having a 'Master' Thumbnail
cache maintained and updated for every file operation.
Certainly, some 3rd Party 'add-ons' (Power Archiver for one! & similar) may cause problems, as can poorly configured A/V programs (realtime checking of Notepad for instance, every time it is opened??? Why not bring back the old innoculate method?) -
but I digress.
For many, the slow Explorer problem exists without any of the suspects / causes mentioned in previous Posts, or elsewhere online.
I repeat: 'This methodology has worked for me - Your Mileage May Vary'.
Now for the fun & games:
Kill the time and resource hog 'Indexing Services' - Plenty of advice on how to do that is available online.
DISALLOW Indexing on all volumes.
To retain the ability to search for my files, I have been using the Search Everything tool from:
http://www.voidtools.com/ which searches ONLY on local or removable NTFS volumes. (ie NOT FAT32 USB Drives!) But that poses very little problem when I examine my real-world use of any Search Tool.
SE needs Administrator privileges for its low-level file-system access, certainly not an issue to have a responsive Global Search at your fingertips.
With 34.5 Gb (> 137,000 files in > 20,000 folders) on HDD, and 627 Gb (> 2,300,000 files in > 82,500 folders) on a Portable USB Drive, Search Everything has about 74Kb RAM usage and the db file is 10.5 Mb on disk - not a huge overhead.
The initial run occupied about 10 minutes of my setting options and less than 5 minutes for the building of the database.
The online FAQ has plenty of information including how to use wildcards, Path Matching, boolean operators and regex use.
With a lean mean responsive search at hand, now to clobber some more of the 'features' which are supposed to 'help' us in our computing experience...
Big Guns Time!
Start Group Policy Editor -
Start > Run > gpedit.msc
Navigate to:
Local Computer Policy > Computer Configuration > Administrative Templates > Windows Components > Windows Explorer
Locate and ENABLE the settings as listed:
1. Turn off the display of thumbnails and only display icons on network folders
Disables the display of thumbnails on network folders in Windows Explorer.
Windows Explorer displays thumbnails on network folders by default.
If you enable this policy. Windows Explorer will only display icons and never display thumbnails on network folders.
That gets rid of the first time-waster - Network access is slow enough without adding the extra traffic for thumbnails, and many PCs are stand-alone anyway.
2. Turn off the caching of thumbnails in hidden thumbs.db files.
Turns off the caching of thumbnails in hidden thumbs.db files.
This policy setting allows you to configure Windows Explorer to cache thumbnails of items residing in network folders in hidden thumbs.db files.
If you enable this policy setting, Windows Explorer does not create, read from, or write to thumbs.db files.
If you disable or do not configure this policy setting, Windows Explorer creates, reads from, and writes to thumbs.db files.
This goes hand-in hand with 1.
3. Turn off Windows Libraries features that rely on indexed file data
This policy setting allows you to turn off Windows Libraries features that need indexed file metadata to function properly. If you enable this policy, some Windows Libraries features will be turned off to better handle included folders that have been
redirected to non-indexed network locations. Setting this policy will:
* Disable all Arrangement views except for "By Folder"
* Disable all Search filter suggestions other than "Date Modified" and "Size"
* Disable view of file content snippets in Content mode when search results are returned
* Disable ability to stack in the Context menu and Column headers
* Exclude Libraries from the scope of Start search
This policy will not enable users to add unsupported locations to Libraries.
If you enable this policy, Windows Libraries features that rely on indexed file data will be disabled.
If you disable or do not configure this policy, all default Window Libraries features will be enabled.
Well, with Indexing turned OFF, this one is a real no-brainer, isn't it?
4. Turn off the display of snippets in Content view mode
Disables the display of snippets when Content view mode is turned on.
Windows Explorer shows snippets in Content view mode by default.
If you enable this policy, Windows Explorer will not display snippets in Content view mode.
That stops peeking into every file and trying to decode the snippet - MORE time-saving.
5. Turn off caching of thumbnail pictures
This setting controls whether the thumbnail views are cached.
If you enable this setting, thumbnail views are not cached.
If you disable or do not configure this setting, thumbnail views are cached.
Note: For shared corporate workstations or computers where security is a top concern, you should enable this setting to turn off the thumbnail view cache, because the thumbnail cache can be read by everyone.
It (IMHO) is faster to generate the thumbnails as needed (for my usage anyway), rather than to be attempting to maintain a global cache each time a file is created, modified, deleted or moved.
This completely cuts out the thumbnail caching overheads, and makes quite an impressive speed difference. Even on an old 1.7 GHz Laptop with 2 Gb RAM and an Intel 915GM Graphics Card (NOT the best choice for Win 7 by any means!).
6. Turn off numerical sorting in Windows Explorer
This policy setting allows you to have file names sorted literally (as in Windows 2000 and earlier) rather than in numerical order.
If you enable this policy setting, Windows Explorer will sort file names by each digit in a file name (for example, 111 < 22 < 3).
If you disable or do not configure this policy setting, Windows Explorer will sort file names by increasing number value (for example, 3 < 22 < 111).
Do I REALLY want to waste the time on this procedure? If I want to sequence my files, I'll prefix the filenames with 0's - 003 < 022 < 111. Not a problem!
Subjectively, these changes make for a much more responsive system.
Objectively, moving over 2.3 Gb (7,500+ files) via 'Drag & Drop' from HDD to USB Drive shrank from 12 Mins+ to about 8 Mins. Explorer did NOT 'freeze', and I could freely change the displayed folders in both the Source and Target Explorer windows.
I hope that this is of use to others, it has served me well for the last several months.
A few minor delays when wanting thumbnail views, but certainly FAR LESS DELAY than before the changes, and
no more stalled Explorer.
2010: - Windows? - MAC OS X? - LINUX? - UBUNTU? - 1982: - Commodore C=64? - Amiga? - BBC Micro? - Apple II? - Same old play, only the actors have changed. -
Photoshop loading photo files very slow (not printer)
For the past several weeks Photoshop C3 has been loading even the smallest of photo files very, very slowly -- about 10-15 seconds for one.
I read an earlier post to this affect, that said it might be a networked printer, but the printer on this computer is NOT networked.
I'm running Windows XP, latest update, with 3 gig of RAM. And we have deleted and reloaded the Photoshop program and updated it to make sure it's not a file goober in the program.
Anyone else experiencing this trend and/or have any solutions.
rfrank
WSU Today
http://www.wsutoday.wsu.eduJohn:
Thanks for the effort, but alas it didnt make any difference.
Our IT support crew tried a variety of generic drivers in the default mode, but a 56k photo still took 15 seconds to load.
However, I still had a version of "Photoshop CS" on my machine. So, out of curiosity I fired up CS and grabbed the same test photos, and bam the photo popped right up. So it is definitely a CS3 issue
Any other solutions that you know of?
rfrank
WSU Today
Maybe you are looking for
-
Payment block rerlease for vendor/customers
Hi Gurus which t-code we used for payment block rerlease for vendor/customers regards Mallikarjuna
-
can someone please help me..error 400 when logging in...tried the fix and still nothing..i want to use the share option..
-
Developer Error: invalid window block name passed to set_window_position
Hi I had Registered a Form in Oracle apps After that i'm trying to open the form,then this message will be displayed Developer Error: invalid window block name passed to set_window_position in the PreForm Trigger I had written the code as apps.set_w
-
Count distinct can not be aggregate
Hi All, I create discoverer report and then create calculation by using Count Distinct function in this cal. when I create total on this calculation the data could not be shown on report. How to correct this problem ? But I don't want to create Custo
-
PSE 10 will not open the picture when coming from "edit in" in LR4.
Just installed LR4, when choosing "edit in" PSE, the Elements program opens, but the picture does not display. Is anyone else having this problem, or know what I need to do to fix this? Thanks