MacBook Air will not power on after going to sleep

I have a 13" MacBook Air (2012) that has been giving me some issues on and off lately. The past month or two, it has had a few instances where it would take a lot of time and work to get it to "wake up" after the lid was opened. A few times I had to hold the power and reboot it as it was non-repsonsive and would not display anything on screen (black screen). Then a few weeks ago it was un-responsive for a minute upon opening the lid but I eventually got it to come alive but it was very slow to get going as there were quite a few programs running and it auto-rebooted itself. Once I logged in, it did it again but this time it got hung up on the apple logo on boot and was in a cycle of trying to reboot itself but failed at the apple logo. I eventually got it into recovery mode and went into Disk Utility. It found some problems with the hard drive and fixed them. After that, it booted up fine and hasn't given me any problems UNTIL... yesterday, it won't even attempt to power on at all. It was working fine yesterday morning and I was only using Safari (no other programs running) then I closed the lid and left for a few hours with it just sitting there. I didn't take it with me, drop it or anything like that (In fact, it's never been dropped). I just left it right there where I was using it and closed the lid. I came back in the afternoon and opened it up and waited for it to come on but nothing happened. It wasn't even powered on as I put my ear up to it and listened for noise. I've tried holding the power button, I've tried Option+Power, I've reset the SMC, but nothing happens. I don't know what else to try. I believe this model may have a recall on the solid-state-drive but I'm not sure that is it as it should at least power on and display a folder with a "?" mark if the hard drive was bad. I'm wanting to attempt to resolve this before I make a 1.5 hour trip to the Apple store so any help and suggestions are welcome.
Things you should know:
It successfully resets the SMC as the orange light flashes green for a few seconds before turning orange again.
I've tried the charger with 2 different plugs with and without the extending cord. I've also tried booting on battery power only.
The power button is not broke as it recognizes it while doing the SMC reset.
Thanks so much for all your help, Silas

dwb wrote:
does the little light on the mag safe dongle turn green to indicate it is charging?
Are you sure you mean green?  Mine is orange when charging and green when fully charged - always been like this with the 3 macbooks I have owned.

Similar Messages

  • My MacBook Air will not power on

    I recently purchased a MacBook Air 13 it has been working fine until today I was on the Internet and the Mac just powered off and will not power back on. The battery is fully charged.

    Portables that will not Power on.
    Go step by step.
    http://support.apple.com/kb/TS1365
    Note: Steps 5 and 6
    Step 5
    Reset SMC.     http://support.apple.com/kb/HT3964
    Choose the method for:
    "Resetting SMC on portables with a battery you should not remove on your own".
    Keep it charging for 2 hours or more.
    Best.

  • Macbook pro will not "wake up" after going into powersave mode?

    I've tried everything. I hit the enter key any key for that matter, reclosing the macbook or even giving it a few moments. I've had some issues with it lately. Like a kernel panic last week, tried a disk utility repair option. Fixed some things but NOT this. any ideas? I think we had a recent update like two, three weeks ago this is becoming annoying. Is my macbook dying? The only time my macbook comes back to life is if I hit the power button for a few seconds. Then a grey screen appears along with a black screen then my regular screen.

    Hello, Libracious,
    It sounds much like your system may be entering what is referred to as 'Safe Sleep.'
    Mac computers: Progress bar appears after waking from sleep
    http://support.apple.com/kb/HT1757
    Safe Sleep ensures that data stored in main memory will not be lost should the computer shut down due to the battery being drained completely . Prior to your computer entering sleep, Safe Sleep automatically saves the contents of main memory—such as desktop settings, open applications, and other work in progress—to the hard drive.
    There are two situations in which a computer will enter safe sleep:
    In the event the battery becomes completely depleted while the computer is asleep, the computer will shut down. But when a power adapter is connected or a freshly charged battery is installed, the computer can be restarted. Press the power button as if turning the computer on and it will automatically return to the desktop state that existed prior to entering sleep. This means that applications and files will remain exactly as they were prior to the computer being put to sleep, making it easy for you to continue with your work.
    With the release of the OS X Mountain Lion v10.8.2 supplemental update 2.0, a new feature was introduced to enter safe sleep after four hours of the computer being connected to AC power. This is an effort to comply with the European Energy Standards (ErP Lot6). This will only occur if there is no wireless or Ethernet activity and no activity from external devices such as USB storage devices.
    Cheers,
    Allen

  • Why is it my macbook air will not print coupons after installing java?

    why is it i cannot print coupons from my macbook air after installing java?

    Hi JDP86,
    Thanks for using Apple Support Communities.
    If your printer is wireless-capable, you should first add the printer to your network. Use the printer's control panel, or temporarily connect the printer to your Mac via USB.
    Use this article to troubleshoot printer issues in OS X.
    Troubleshooting printer issues in OS X
    http://support.apple.com/kb/ts3147
    Best of luck,
    Mario

  • MacBook Air will not reboot. A file folder with a question mark in the center of it appears. What is the problem?

    MacBook Air will not power on or reboot. A file folder with a question mark in the center of it appears. What is the problem?

    Go step by step and test.
    http://support.apple.com/kb/ts1440
    Startup Manager to select Startup disk.
    http://support.apple.com/kb/HT1310
    Repair Disk
    Steps 2 through 8
    http://support.apple.com/kb/PH5836
    Reset PRAM.
    http://support.apple.com/kb/PH4405
    Reinstall OS X
    If this does not help, contact Apple.
    Best.

  • Macbook Air won't power up after update

    My son is on an internship in Alaska with his Macbook Air -- bringing the Macbook Air in to a "Genius" is not an option.
    His Macbook Air (about 2 years old) has been working perfectly, but then this morning Apple pushed an update so he downloaded and applied it and now his Macbook Air will not power on. At all.
    Is there a reset hole / button or anything he can do? Or is he just out of luck for the next several weeks until he comes back?
    I cannot tell you which release the Macbook Air is, given that he cannot power it up to see, but he, like all of us, is running the latest OSX.

    Thanks to Loner T and others in that thread I linked to above, my son's Macbook Air is now working again.
    Doing the following 3 times brought it back:
    1. Shut down the computer.
    2. Plug in the MagSafe power adapter to a power source, connecting it to the Mac if its not already connected
    3. On the built-in keyboard, press the (left side) Shift-Control-Option keys and the power button at the same time
    4. Release all the keys and the power button at the same time
    5. Press the power button to turn on the computer.
    Note: The LED on the MagSafe power adapter may change states or temporarily turn off when you reset the SMC.

  • Sleep light is on but MacBook pro will not power up

    Sleep light is on but MacBook pro will not power up

    Hi a,
    If the sleep light is already on when you try to start up, that means the MBP isn't shut down, so cannot start up. Hold down the power button for 5-10 seconds to shut it down, then try starting up.

  • My 13.3" macbook pro will not power up.The battery indicator light does not come on.The Mag safe charging light flickers green and red dimly.I had a cell phone connected to the USB port.

    My 13.3" macbook pro will not power up.The battery indicator light does not come on.The Mag safe charging light flickers green and red dimly.I had a cell phone connected to the USB port.

    This didn't work for me, so I did a bit of searching and TONS of pages later in google, I found an answer. Here are the steps for people who also were in my situation:
    1. Take off bottom case
    2. Unplug battery - blurry image here: http://i.ytimg.com/vi/03cC79r5Dx4/0.jpg
    3. Press and hold power button for 5 seconds
    4. Plug a charger in, and it should start booting up
    5. After shutting down again, reconnect the battery and close the case up
    6. It works! (hopefully, if you guys had the same situation I did)

  • My macbook air will not turn on and it has been charging all night? What to do?

    My Macbook Air will not turn on this morning after charging all night, what can I do to start it?

    Check the adapter >  Apple Portables: Troubleshooting MagSafe adapters
    And try a different electrical outlet.

  • Macbook Air will not connect to the internet via Wi-Fi or Ethernet

    Macbook Air will not connect to the internet via Wi-Fi or Ethernet? Any ideas why not and how to fix this problem?

    Power down the router. Unplug the cord from the wall. Wait a while.
    Plug the cord back in. Restart the router.
    Wait until all the lights are lit up properly.
    Restart the computer.
    Best.

  • HT1338 I've tried everything and all of the sudden my macbook air will not let me use my PhotoBooth or FaceTime it says not connected to camera? help!?

    've tried everything and all of the sudden my macbook air will not let me use my PhotoBooth or FaceTime it says not connected to camera? help!?

    iSight camera failure after OS X 10.9 Mavericks update

  • My MacBook Air will not turn on. I get a white screen with the apple logo and a spinning star that just does that for hours

    My MacBook Air will not turn on. I get a white screen with the apple logo and a spinning star (search icon). It will spin for hours and never go away unless I power off.

    Take each of these steps that you haven't already tried. Stop when the problem is resolved.
    To restart an unresponsive computer, press and hold the power button for a few seconds until the power shuts off, then release, wait a few more seconds, and press it again briefly.
    Step 1
    The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
    There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
    a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
    b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
    c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
    d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
    Step 2
    If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
    Step 3
    Sometimes a startup failure can be resolved by resetting the NVRAM.
    Step 4
    If a desktop Mac hangs at a plain gray screen with a movable cursor, the keyboard may not be recognized. Press and hold the button on the side of an Apple wireless keyboard to make it discoverable. If need be, replace or recharge the batteries. If you're using a USB keyboard connected to a hub, connect it to a built-in port.
    Step 5
    If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
    Step 6
    Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
    Step 7
    If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
    Start up in safe mode. Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
    Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
    The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
    When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
    If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
    If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
    Step 8
    Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
    This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
    Step 9
    If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.  
    Step 10
    Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
    Step 11
    Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
    Step 12
    This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
    Step 13
    If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

  • My macbook air will not connect to the internet due to a self assigned IP address. I have tried trawling the support forums, but either I can't understand the suggestions, or they don't work. Please explain to me in simplest terms how to fix this. Thanks!

    My macbook air will not connect to the internet due to a self assigned IP address. I have tried trawling the support forums for hours, but either I can't understand the suggestions, or they don't work. Please explain to me in simplest terms how I can fix this. Many thanks!

    The warranty entitles you to complimentary phone support for the first 90 days of ownership.
    If you bought the product in the U.S. directly from Apple (not from a reseller), you have 14 days from the date of delivery in which to exchange or return it for a refund. In other countries, the return policy may be different. If you bought from a reseller, its return policy applies.

  • My Mac Mail subfolders on my MacBook Air will not sync in alphabetical order. I am assuming it is a setting that I am not finding since my iMac based at my home office is fine, so is my iPad and iPhone. The core source is Exchange.

    My Mac Mail subfolders on my MacBook Air will not sync in alphabetical order. I am assuming it is a setting that I am not finding since my iMac based at my home office is fine, so is my iPad and iPhone. The core source is Exchange.

    If you have been using the mac.com Apple ID to make iTunes purchases recently, then there should be no issues continuing to use it with the new iPhone. I would abandon the new ID as you will never get Apple to merge the two IDs. I have had a mac.com ID for years and continue to use it with my iPhone 4S.
    Tell us the issues that you encounter trying to set up the iPhone with the mac.com account.

  • IMessage on my macbook air will not connect.

    iMessage on my macbook air will not connect. It says "Could not sign in. Please check your network connection and try again." I have gone through all the support instructions and a lot of these discussion chats. I have sign out of it and my phone and resigned in. I have checked that everything is verified and connected. My ios is up to date on both my computer and phone. It worked fine until about a week ago and suddenly it stopped
    Thank you for your assistance!

    Hi,
    In Hard Drive/Library/Fonts  do you have the AppleGothic.ttf  Font.
    The iMessages account uses this to "register".
    If the computer has been Off then the App effectively "registers" the Apple ID again.
    It cannot do this is the Font is "missing".
    The thread I saw that highlighted this as an  issues said the font could be downloaded from Apple  but not the "how" of that.
    8:08 pm      Wednesday; July 16, 2014
    ​  iMac 2.5Ghz i5 2011 (Mavericks 10.9)
     G4/1GhzDual MDD (Leopard 10.5.8)
     MacBookPro 2Gb (Snow Leopard 10.6.8)
     Mac OS X (10.6.8),
     Couple of iPhones and an iPad

Maybe you are looking for