MacBook Pro Target to G4 Blue & White (350Mghz)

Trying to target my old G4 to use hard drive as file back up from MacBook Pro - but it doesn't seem to be targetable or recognize a targeted CPU - any suggestions? Wireless connection too slow...

It's a "Blue and white" G4?
I had an old Blue and White/350 but it was a G3 and, I think, one of the first powermacs with firewire, but it didn't support Target Disk Mode. If you're powermac is a Blue and White G3, then it won't work.
Here's the Apple Support Doc on it:
http://docs.info.apple.com/article.html?artnum=58583
You might consider just pulling the hard drive out and putting it in a Firewire Enclosure. I have one from OWC and I'm very happy with it:
http://eshop.macsales.com/shop/firewire/usb/eliteclassic
I also have one from Macally, which was cheaper, but it still works fine.

Similar Messages

TS2570 after startup, my macbook pro goes to a blue screen and stays. this article says it won't work for the blue screen problem... any ideas?

My Macbook Pro stays on a blue sceen after start up. It won't boot into safe mode (holding down the shift key).
What do I do?

Hi Mindy, it may though, did you try it?
Could be many things, we should start with this...
"Try Disk Utility
1. Insert the Mac OS X Install disc, then restart the computer while holding the C key.
2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu at top of the screen. (In Mac OS X 10.4 or later, you must select your language first.)
*Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.*
3. Click the First Aid tab.
4. Select your Mac OS X volume.
5. Click Repair Disk, (not Repair Permissions). Disk Utility checks and repairs the disk."
http://docs.info.apple.com/article.html?artnum=106214
Then try a Safe Boot, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, reboot when it completes.
(Safe boot may stay on the gray radian for a long time, let it go, it's trying to repair the Hard Drive.)
If perchance you can't find your install Disc, at least try it from the Safe Boot part onward.
If 10.7.0 or later...
Bootup holding CMD+r, or the Option/alt key to boot from the Restore partition & use Disk Utility from there to Repair the Disk, then Repair Permissions.

My Macbook Pro won't get past white screen....

My Macbook Pro is stuck on the white screen with the gray apple logo and loading gear spinning below---for hours now. Restarted multiple time without any change. Agh!

Boot in safe mode. First, disconnect all wired peripherals except keyboard, mouse, and monitor, if applicable, and remove all aftermarket expansion cards. The instructions provided by Apple are as follows:
Be sure your Mac is shut down.
Press the power button.
Immediately after you hear the startup tone, hold the Shift key. The Shift key should be held as soon as possible after the startup tone, but not before the tone.
Release the Shift key when you see the gray Apple icon and the progress indicator (looks like a spinning gear).
Safe mode is much slower to boot and run than normal.
If you can boot in safe mode, try rebooting as usual (i.e., not in safe mode.)

TS3423 My MacBook Pro freezes on the blue start up screen. What can I do?

My MacBook Pro freezes on the blue start up screen. What can I do?

See if this will help:
http://support.apple.com/kb/PH7212
Ciao.

Why does my macbook pro "15 get a blue, black or gray screen and force a shut down?

Macbook Pro 15 inch
OS X 10.9.4
2.4 GHz Intel Cor i7
4 GB 1333 MHz DDR3
I have had my macbook pro for just over 2 years. About a week ago it started randomly giving me a blue striped, grey, or black screen. The fan pins up and won't stop and either the laptop shuts itself off or I have to force it off. When it restarts it is very slow and sometimes the fan kicks on and won't stop and the screen just stays white after the initial apple and spinning wheel screen, so I have force shut it down and try again. Other times it eventually loads and lets me in but everything responds slowly and takes some time to open. It has been getting worse and now I can't do things like watch Netflix or edit in Final Cut. I have an editing project I must get done this weekend. Any ideas or help? Thanks in advance.

Try running the Apple Hardware Test, not definitive but will pick up the obvious.
AHT http://support.apple.com/kb/HT1509

Macbook Pro won't load past white loading screen when turned on after kernel panics

Hello,
I have a Macbook Pro and recently its been having repeated kernel panics. In the past few days its been turning off every few minutes or so. yesterday it had one and now when I try to turn it on it doesn't load. I get the white loading screen with the apple logo and a loading bar underneath. But after the bar fills about 5% of the way (if that) the bar just disappears and the spinning loading icon just keeps going without anything happening (however long I leave it).
Please can someone give me some suggestions to fix this. Just a few things to note:
a) I'm not great with computers so any fixes please explain in the most simple terms
b) I have VERY important work files on there that are NOT backed up (big mistake I know), so please only suggest fixes that will not remove these Microsoft Word files. Guaranteeing the safety of my work is paramount with any suggestions.
c) I may not have any of the disks which came with the Macbook Pro originally (though I may somewhere)
d) I've read some other forum posts and it seems that I need to know the details of my operating system. I don't know these and have no way of accessing them on the computer (for obvious reasons). Its a late 2011 Macbook Pro if that is of any help.
A massive thank you to anyone who can suggest a fix to these, I shall be eternally grateful.

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a boot failure is to secure your data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since your last backup, you can skip this step.
There are several ways to back up a Mac that is unable to boot. You need an external hard drive to hold the backup data.
a. Boot into the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. The easiest way to deal with the problem is to boot from an external drive, or else to use either of the techniques in Steps 1b and 1c to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a boot failure can be resolved by resetting the NVRAM.
Step 4
If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to boot, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can boot now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've booted from an external storage device, make sure that your internal boot volume is selected in the Startup Disk pane of System Preferences.
Boot in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you boot in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, your boot volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 6.
If you can boot and log in now, empty the Trash, and then open the Finder Info window on your boot volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then reboot as usual (i.e., not in safe mode.)
If the boot process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select your startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then reboot as usual.
Step 9
Reinstall the OS. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 10
Repeat Step 9, but this time erase the boot volume in Disk Utility before installing. The system should automatically reboot into the Setup Assistant. Follow the prompts to transfer your data from a Time Machine or other backup.
Step 11
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a boot failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 12
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

MacBook Pro (late 2011) stuck at white Apple screen.

Hi all. My MacBook Pro 13 inch (late 2011) is giving me the same problem over and over again.
Few months ago, I had sent it to Apple for repair due to faulty HDD. Now the same problem happened again. The MacBook will stuck at the white Apple screen with the circle turning when attempting to switch on.
However, Apple had just replace a new HDD and why it's still happening again?
Can anybody here please assist to advice me what is making my Mac unable to start up, stuck at the white Apple screen, even after replacing a new HDD?
Thank you!

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a boot failure is to secure your data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since your last backup, you can skip this step.
There are several ways to back up a Mac that is unable to boot. You need an external hard drive to hold the backup data.
a. Boot into the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to boot, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can boot now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
If you've booted from an external storage device, make sure that your internal boot volume is selected in the Startup Disk pane of System Preferences.
Step 3
Boot in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you boot in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, your boot volume is damaged and the drive is probably malfunctioning. In that case, go to step 5.
If you can boot and log in now, empty the Trash, and then open the Finder Info window on your boot volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then reboot as usual (i.e., not in safe mode.)
If the boot process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 4
Sometimes a boot failure can be resolved by resetting the NVRAM.
Step 5
Launch Disk Utility in Recovery mode (see Step 1.) Select your startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then reboot as usual.
Step 6
Boot into Recovery again. When the OS X Utilities screen appears, follow the prompts to reinstall the OS. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Note: You need an always-on Ethernet or Wi-Fi connection to the Internet to use Recovery. It won’t work with USB or PPPoE modems, or with proxy servers, or with networks that require a certificate for authentication.
Step 7
Repeat step 6, but this time erase the boot volume in Disk Utility before installing. The system should automatically reboot into the Setup Assistant. Follow the prompts to transfer your data from a backup.
Step 8
A dead logic-board battery in a Mac Pro can cause a gray screen at boot. Typically the boot failure will be preceded by loss of the startup disk and system clock settings. See the user manual for replacement instructions.
Step 9
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store to have the machine tested.

MacBook Pro Target Display to iMac - Black Screen

I have a MacBook Pro (13'', Early 2011) & iMac (21.5", Mid 2011) using a Thunderbolt Cable to Target Display. Everything was working find and I could Command F2 to Target Display as expected.
However, about a week about this stopped working. Now when I try to Target Display the iMac goes to a Black screen (like it's switching to Target Display) and the MacBook Pro does nothing. The iMac will be at the Black screen until I Command F2 again (or disconnect the Thunderbolt Cable), then the iMac goes back to the normal display.
I have tried another Thunderbolt cable with no luck. I have perform all software updates on both machines (now both running 10.7.3) and fixed Disk Permissions.
I have also found that restarting my MacBook Pro allows this to function as excepected (Command F2, Blue Flashing Screen, Target Display on the iMac). However, this is not an ideal situation since having to restart my computer is time consuming.
Any suggestions would be appriciated.

Hello all -
I've done some additional testing. I tried an completely different iMac (and Thunderbolt cable) this morning and saw the exact same behavior so it is definitly something specific to the MacBook Pro.
Again, a restart resolve the issue, so it appears to be related to after the computer goes into a hard sleep (cover closed), because I can leave for lunch (cover open) and the display will go to sleep and things will still work as expected.
Any thoughts/ideas woudl be appriciated.

Blue Screen of Death on New Macbook Pro 13 Inch a blue

My macbook pro 13 Inch is a week old, and so far it has been freezing, with just a blue or yellow screen about twice per day. I'm using an external monitor as well as the laptop screen. I have to re-set (restart) the computer. There is an EFI firmware update available to correct a problem with the 15 and 17 inch versions not responding, but I'm assuming that that isn't appropriate for my 13 inch.
Anyone have any ideas?

AASP is an Apple Authorized Service Provider. To locate one in your area please follow this site:
https://selfsolve.apple.com/GetWarranty.do
Regards,
Roger

TS3423 17" macbook pro won't start blue file with question mark is all that appears on the screen

My old macbook pro will not start up. Worked fine yesterday, today all I gat is the startup sound and a blank blue screen. After a while the screen shows a file folder icon with a question mark in it. Any ideas

Question (?) Mark, Blinking Folder, or Gray Screen at Startup
These are related but not identical issues. Their causes are outlined in Intel-based Mac- Startup sequence and error codes, symbols. Solutions may be found in:
A flashing question mark appears when you start your Mac
Mac OS X- Gray screen appears during startup
In most cases the problems may be caused by:
Problem with the computer's PRAM - See Resetting your Mac's PRAM and NVRAM.
Boot drive's directory has been corrupted - Repair with Disk Utility.
Critical system files are damaged or deleted - Reinstall OS X.
The disk drive is physically non-functional - Replace the hard drive.
Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
The main difference if you are using Lion or Mountain Lion is that you must first boot from the Recovery HD:
Boot From The Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Reinstall Snow Leopard Without Erasing The drive
1. Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Reinstall Snow Leopard
If the drive is OK then quit DU and return to the installer. Proceed with reinstalling OS X. Note that the Snow Leopard installer will not erase your drive or disturb your files. After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
Download and install Mac OS X 10.6.8 Update Combo v1.1.
Reinstalling Lion/Mountain Lion Without Erasing The Drive
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
Reinstall Lion/Mountain Lion: Select Reinstall Lion/Mountain Lion and click on the Continue button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.

MacBook Pro starts off in blue washed out tint then goes to grey screen

So I took out the stock HDD and replace it with a SSD and the laptop with working better then ever. Then later on at night I used the thunderbolt plug to connect it to a TV. After about 5 min the computer froze so I restarted it. But now when it reboots the screen has a blue washed out look. It won't open into OS X, instead the apple logo comes then the screen turns into a solid grey. It recognizes the SSD when I hold option but won't open it up. So I put the HDD back in and it does the same thing.
My MacBook Pro is an early 2011 15 inch with anti glare display
I'm pretty sure it was running on Mountain Lion because I didn't get a chance to upgrade to Mavericks yet.
The SSD is a 960 Crucial SSD.
I am past warranty with Apple Care so is there anything I can do to fix this?

#2 NVRAM reset
..Step by Step to fix your Mac
Use TRIM Enabler on your third party SSD over at MacUpdate.com to enable TRIM in system profiler to check.
Right or control key click to open past Gatekeeper.

Macbook Pro boots to a blue screen. Only boots in safe mode

Hi, I am a long time reader, first time poster.
OK so I just go a new Macbook Pro 13' from my school (my school made it mandatory to get a mac this year) and I was installing some of my applications. Then I got the "You need to restart your computer" message. I restarted, and all i got was a blue screen with my pointer. Then after a while it says the same restart message. Also I have tried booting from the Snow Leopard Disk, but I get the same message before the actual SL installer comes up. I have been able to get the Macbook to boot in safe mode and I repaired permissions and the disk, however that does not seem to help. I have also reset the PRAM and that did nothing. I am running out of ideas... how can I fix this?!? Help!

You should not be having kernel panics on a new Mac. Kernel panic causes is sometimes hardware related. Your computer is still under warranty since it's new. You can either call Apple tech support or try the suggestions mentioned in User Tips: Kernel Panics and this article - http://support.apple.com/kb/HT1392

MacBook Pro 15 inch 2011- Blue tint in Windows 7 using Bootcamp 4.0

I have recently installed Windows 7 using Bootcamp on my Macbook pro 15 inch 2011. The display under Mac OSX is accurate with vibrant colors using the default Color LCD profile. In WIndows 7, everything is tinted blue and all colors are dimished because of this. I have tried importing my Color LCD icc profile from Mac OSX Lion and this has helped to some degree. This alleviates the blue tint but gives Windows a warmer, browner tint. Unfortunately this makes the display too dim and crushes the blacks. Additionally, some games revert to the default windows calibration with the blue tint. Games look bad either way as the Color LCD profile in Windows makes the game too dark and the default calibration makes everything blue. Has anyone been able to correct this in Bootcamp?Thanks

msconfig / chkdsk / Windows 7 DVD system repair or rollback restore point
Ccleaner 3.09 - remove temp files and caches / also run Registry section
Start: Run %TEMP% (select all) and remove all the contents in there
Heat, fans, poor Apple drivers, I would not blame ATI but I would upgrade/install those.
And yes BC 4.0 probably was not tested fully.

Why does my MacBook Pro go to a blue screen?

Hi there. Has anyone experienced their MacBook Pro randomly going blank or to a blue screen in the middle of working? It is random and i cannot repeat the steps, but the most recent time, I was in Safari, working on a WordPress template and my screen went blue and was unresponsive. The only way I can get a response is to do a hard reboot. This works and everything seems fine after restart, but it happens every so often with no explanation. Any suggestions?
thanks,
Lisa

Did you also have this=> https://discussions.apple.com/message/20855553#20855553
First i had a blue screen to but a few weeks later it chanched to a screen freze
grtz Tom

Can MacBook Pro Ram fit in a white 13" MacBook?

Hello there,
I have a Macbook Pro 15" (mid-2010) and my wife has a white Macbook 13" (mid to late 2008). I'm upgrading my 4GB ram to 8GB. Does anyone know if my ram can fit into my wifes MacBook?
Thanks,
Lorne

No, your Mac book Pro uses 204pin 1066mhz PC3-8500 RAM
The model 4,1 (Early 2008) White MacBook uses 200 pin 667mhz PC2-5300 RAM

MacBook Pro Target to G4 Blue & White (350Mghz)

Similar Messages

Maybe you are looking for