Maintenance Optimizer - SMSY (ABAP + JAVA)
Hi gurus,
I will try to explain what is my doubt/problem.
We have a system ECC 6.0 with both stacks ABAP + JAVA. We want to do a support packages update, so I went to maintenance optimizer (MOPZ) and I choose that system, but during the process, after I select the SPS 18, in the end of MOPZ process, only ABAP packages (stack 18) were calculated! Which means the JAVA support packages was not maintained in Download Basket! Why?!
I would expect that process on MOPZ did this calculation for both stacks ABAP and JAVA together, but not, there is only ABAP packages in Download Basket!
Because I also want to do JAVA support packages Update (with JSPM)!
I guess this is a problem in SMSY... in Instance definition, isn't it?
Can you help me please?!
Thank you
João Dimas - Portugal
Hi,
The SMSY definition would be the problem.
Make sure the Java based techincal usage types are also selected for the system under the Product Instance Selection tab.
Also, a corresponding technical system should be created for the Java part. The technical system details should contain information about the Java stack i.e. message server, dispatcher port, software components etc.
Ideally all the above information should be populated automatically if the Java part of system is registered properly on the SolMan SLD and SMSY_SETUP has run successfully.
Regards,
Srikishan
Similar Messages
-
Maintenance Optimizer - ABAP queue check failed
Hi guys.
When running Maintenance Optimizer for a SAP ERP 6.0 EHP4 which has SAP HR 604 installed, the following message is displayed
ABAP queue check failed
Error The Installation/Upgrade Package for Add-on SAP_HR rel. 600 is not available.
The goal is update toEHP7 SP2.
Not sure why is stating SAP_HR rel. 600 package is not available when the system has 604 release.
During packages selection, Human Capital Management is checked and on the source system is listed SAP_HR 604 SP12
The Solution Manager version is 7.1 SPS8, CR Content is updated to 9.9.
Also have applied SAP Note 1277035 Recommendations, releted to EHP4 Missing, but still no luck
This seems to be similar when SUM perform an EHP Inclusion, and cannot find the packages on the EPS Directory, but this is happening on the Maintenance Optimizer.
Is this a problem with SAP Backbone, or should i do some manual corrections on the system or Solution Manager to make it aware SAP_HR is at al level 604 SP 12?
Thanks!Hello,
That type of error you describe is mostly always related to an issue in the SMSY/LMDB definition.
It is likely that the issue is a wrong product instance was assigned to the system.
In LMDB it is easy to check , even without verification checks (which sometimes may be the root cause, a bad verification check happens sometimes). If you go to the product system, then open the node technical systems -> AS ABAP -> Software, and go to the product instance tab (in SP10, product instance - details), when you select a given product instance , you see whether the software components that are part of it are installed or not (there is a frame in the lower part of the screen that shows the software components with flag 'installed' ticked or not). Chances are, one or more of the instances have few or no software components installed.
Mind you, you must keep at least one SAP ERP 6.0 product instance assigned, this would be the exception to the rule, but if you have an EHP4 for SAP ERP 6.0 system, it should be only one.
Best regards,
Miguel Ariño -
Maintenance Optimizer in SAP Solution Manager
what is Maintenance Optimizer in SAP Solution Manager and what are its benefits
Hi
even this may be useful
Ensure your Solution manager system is at the most recent Support Package Level, specifically ST 400 Patch 11, to reduce note application time
Download from oss most recent step-by-step setup guide
Oss note 1024932
Oss Note 1008717 ( N/A )
Relevant up to SP11 for Basis 700
OSS Note 950975 support for IE7 ( N/A we are using GUI)
Oss note 975510 corrections for snote ( Via OSS not snote )
Oss note 1004691 corrections for snote *** Corrections for 975510 ( UP TO SAP_BASIS 11 ) N/A
Common problem notes, but not critical for Maint Opt
0998987: Maintenance Optimizer: Empty error messages
1022072: Maintenance Optimizer: "No Data Available" message o See note 1025381 before applying 1022072.
1020789: Maintenance Optimizer: Allow all systems to be selected
1020802: Maintenance Optimizer List displays incomplete data
1024105: Maintenance Optimizer: two "Cancel" buttons
1025381: Maintenance Optimizer: Link to additional download files
1029453: Maintenance Optimizer - Wrong status displayed
1030405: Maintenance Optimizer: Browser opens in background
1030498: Maintenance Optimizer - IBase is not active
1032463: Maintenance Optimizer: Internet Explorer Script Error
1042704: Maintenance Optimizer: Display only employee partners
Partner Scenario SOLMAN4.0 Only
Os note 1021275 ( RFC Destinations ) N/A ST 400 11
Oss Note: 997780 ( N/A we are at 11 use note 939897 for ST400 SP11 Application )
Relevant for ST400 SP09 ( N/A ST 400 11 )
User:
To setup you must have SAP_ALL
General Users: ( Oss note 1032322 )
Must be assigned to role SAP_MAINT_OPT_ADMIN
Auth Object: D_SOL_VSBL ( visibility of solutions)
Auth Object: CRM_ORD_PR ( for CRM stuff )
/spro
As of Support Package level ST 400 SP10:
Call Transaction SPRO -> SAP Reference IMG ->SAP Solution Manager -> Advanced Configuration -> Basic Settings -> SAP Solution Manager System -> Change Management -> Set Up Maintenance Optimizer
This IMG activity refers to the SAP Note 990534: Solution Manager Maintenance Optimizer: BC Set. Follow the instructions in this SAP Note
N/A as of ST400 SP11
Define a Solution:
Solution_Manager Select Solution Overview New.
Enter Descriptive Name ( Ex. GTS Landscape )
Hit Continue
Select Solution Landscape Maintenance
Select System Groups & Logical Components on the Left hand Side
Select Solution Landscapes and pick the one you created
Define the solutions for that landscape
Highlight each item and click Logical Component (You must have a valid license to set this up)
Assign S-User
Transaction: AISUSER
Enter you user id and your SUSER ID for downloading
Create another SAPOSS Connection called SAP-OSS with S-User assigned
Call SOLUTION_MANAGER
Select Solution Overview
Select the solution you want to work with
Select Change Management Support Package Stacks
Click Maintenance Optimizer around middle of screen
Select the solution you want to get Sps for
Go to OSS and add the files to download basket
When done return to screen and hit continue
Select - Confirm files in Download Basket
Error message comes if your sap user and your oss user are not setup in AISUSER screen
Now go to SAP Download Manager ( On your local pc ) and download the files you just confirmed of course using the same S-User id you just added them to the basket with
Apply support packages via spam per normal process
Return to the SOLUTION_MANAGER window select the landscape you are working on
Hit Maintenance Optimizer List
Choose the maintenance transaction you are working on
You will see a list of the confirmed and downloaded sps you selected
Once you apply these to the system using SPAM you will change the status of implementation to Completed and Hit Save
This completes this activity
If you wish to do more work you will have to create a new transaction.
[Edit section] Add A New Instance to Maintenance Optimizer
Sign into Solution Manager
Ensure new instance has valid license installed and logical clients assigned
Select Landscape Components
Right Click Systems
Select Create new system with assistant
Enter
SID / Description / Product Type / Installation Number ( Get this from SLICENSE in system you are setting up )
Next enter Sys # & MEssgae Server and hit continue
Next select Generate RFC Destinations & Assign Logical Components & Enter Client #
I always get a problem saving since SLD is not setup ignore and continue
Highlight the system you just added under Systems SAP Global Trade Services
Select Assignment to Logical Components
Now add additional software such as Net weaver ABAP & JAVA if your primary setup was of another type ( ex. GTS )
Highlight the system you wish to update under Systems and hit change
Select Header Data
Click Installed Product Versions
In the product box add whatever you require for this system
Select the version from the 2nd box and hit copy
Ex.
If you cannot setup the trusted system here is a workaround:
Create User in Target for Trusted System RFC from SM1
User: <Username>
Pass: <Pass>
Type: Communication
Use this when setting up the trusted connection, remove the trust and use this CPIC user info for the RFC.
Generate RFCs and ensure SMSY setup is done for SID in Solution manager
Now Create a New Solution For your instance:
Go to SOLUTION_MANAGER transaction
Select NEW
Give Descriptive name: ex. GTS Landscape
Under Solution Landscape
Select Solution Landscape Maintenance
Select System Groups and Logical Components Tab
Open Solution Landscapes
Select the one you just defined (GTS Landscape)
SOLTION_MANAGER
Select Change Management Support Package Stacks
Select Maintenance Optimizer
Select the Product Version
GTS 7.1
Select the System Type SID
From here you will be prompted to go to service marketplace and add the items you wish to install. You can do this beforehand as well, be sure to use the same Suser you setup in AISUSER with your sap login
It will ask you to confirm the basket, once you do that you install them normally.
Download with sap download manager, ftp and apply -
Download Stack from SAP Marketplace to my ECC 6.0 (abap+java)
Hi gurus
I have a doubt about the process of support package (stack) download. I don´t want downloading from maintenance optimizer, I´m doing this process directly from Sap Marketplace, in first step (1 of 3) I have to select the target stack (which is the stack level that I intend to make an update) and the source target (which is the actually stack level of my system)... Ok I choose them with no problem, the situation and my doubt is below that where I have a check list of "Usage Selection" (image). How can I know which one I must choose for my system... I don´t understand what is that, for instance "Strategic Enterprise Mgmt" ; E-"Recruting" or "EP Core"!!!... etc...
So how can I know which of these components I need to check to downloading for my system, how can I know that?
*Image: http://img188.imageshack.us/img188/664/imagem1b.jpg
Help me please!
Best regards,
João Dimas - PortugalHi Sunny,
Yes ok, I understand that but... I think I didn´t explain what I want to learn/know or you didn´t understant what I want...
At download windows you see this list:
ERP Central Component (ECC)
XI Content
Strategic Enterprise Mgmt
Self Services
Supplier Relationship Mgmt
Extended E-Commerce Components
Financial Supply Chain Mgmt
cProject Suite
E-Recruiting
Learning Solution
Process Integration (XI)
Workforce Mgmt Core
Business Intelligence
Portal Content
Enterprise Portal
Easy Document Management
EP Core
Mobile Infrastructure
How can I know which of these types I must have choose for my system...? The output of that url doesn´t inform me which of these type I have in my system, it only inform me the master components or in other words which stacks I have in my system (ABAP and JAVA stack´s)!!!
Best regards,
João Dimas - Portugal
Edited by: João Dimas on Jul 2, 2009 2:28 PM -
Solution manager maintenance optimizer
Hi all,
I have what I think is an issue, and hoping someone could possibly point me in the direction to correct. I have setup our solution manager system and trying to get the maintenance optimizer option working fully. I have a java system that I pull the information from SLD perfectly fine, and it lists all installed software components via SMSY>SYSTEMS perfectly. I have assigned logical components etc. I can create a new maintenance optimizer transaction, select the proper system with assigned components, but when it lists the files to be downloaded automatically I expect to see alot more files available for download than it lists for me. I assume I am missing something, but not sure where to look.
Would anyone be able to possibly point me in the right direction on what I might be missing?
Regards,
ChrisHi Markus,
The system is SAP EHP1 for SAP Netweaver 7.0. It has the following components installed and specified in logical components:
Adobe Document services
Application server Java
EP Core
Enterprise Portal
Along with the kernel files I also get the following files available for download via maintenance optimizer (6 in total)
FORUMS06_0-10005892.SCA SP06 for FORUMS 7.01
BP_PROJ_PORT_DESIGNCOLL
BPPPMDC17_0-10003174.SCA BP PROJ., PORT. & DCOL. 4.0 SP17
BP ERP05 PROJ SELF-SERV
BPERP5PSS17_0-10003284.SCA BP ERP05 PROJ SELF-SERV 1.0 Support Package 17
BP ERP05 MAINTENANCE TECH
BPERP5MTC07_0-10004455.SCA SP07 for BP ERP05 MAINTENANCE TECH 1.2
BP ERP SITE TECHNICIAN
BPIS7TST07_0-10004458.SCA SP07 for BP ERP SITE TECHNICIAN 1.20
BP ERP ICM ANALYST
BPIS7ICMAL06_0-10006119.SCA SP06 for BP ERP ICM ANALYST 1.41
When I look at installed system components via SMSY it correctly shows everything installed which includes:
ADOBE DOCUMENT SERVICES 7.01 0006 SP006 ADOBE DOCUMENT SERVICES 7.00
BI BASE SERVICES 7.01 0006 SP006 BI BASE SERVICES 7.01
BI INFORM. BROADCASTING 7.01 0006 SP006 BI INFORM. BROADCASTING 7.00
BI META MODEL REPOSITORY 7.01 0006 SP006 BI META MODEL REPOSITORY 7.01
BI REPORTING AND PLANNING 7.01 0006 SP006 BI REPORTING AND PLANNING 7.01
BI UNIVERSAL DATA INTEGRATION 7.01 0006 SP006 BI UNIVERSAL DATA INTEGRATION BI UDI 7.01
BI WEB APPLICATIONS 7.01 0006 SP006 BI WEB APPLICATIONS 7.00
BI WEBDYNPRO ALV 7.01 0006 SP006 BI WEBDYNPRO ALV 7.01
BP ERP FIN MDM 1.40 0006 SP006 BP for Financial MDM 1.40
BP ERP HR EIC 1.40 0006 SP006 BP für HR Employee Interaction Center 1.40
BP ERP ICM ANALYST 1.41 0004 SP004 BP for ICM-Analyst 1.41
BP ERP RECRUITER 1.40 0006 SP006 BP for Recruiter 1.40
BP ERP RECRUITING ADMIN 1.40 0006 SP006 BP for E-Recruiting Administrator 1.40
BP ERP SITE TECHNICIAN 1.20 0006 SP006 BP for Site Technician (Telecommunications) 1.20
BP ERP UT XSS 1.40 0006 SP006 BP ERP UT Definition für Self Service BP 1.40
BP ERP05 BUS UNIT ANALYST 20 1.0 0017 SP017 BP for Business Unit Analyst (mySAP ERP) 1.0
BP ERP05 COMMON PARTS 1.41 0006 SP006 BP ERP05 COMMON PARTS 1.41
BP ERP05 ESS 1.41 0006 SP006 BP for Employee Self-Service 1.41
BP ERP05 HR ADMINISTRATOR 1.41 0006 SP006 BP for HR Administrator (mySAP ERP) 1.41
BP ERP05 MAINTENANCE TECH 1.2 0006 SP006 BP for Maintenance Technician 1.2
BP ERP05 MSS 1.41 0006 SP006 BP for Manager Self-Service 1.41
BP ERP05 PROJ SELF-SERV 1.0 0016 SP016 BP for Project Self-Service (mySAP ERP) 1.0
BP ERP05 SELF-SERV ADMIN 1.0 0017 SP017 BP for Self-Service Administrator (my SAP ERP) 1.0
BP ERP05 TALENT DEV 1.01 0010 SP010 BP for Talent Development Specialist 1.01
BP_PROJ_PORT_DESIGNCOLL 4.0 0015 SP015 BP for Project Portfolio Management and Design Collaboration 4.0
CAF EU 7.01 0006 SP006 SAP Net Weaver End User 7.01
DI BUILD TOOL 7.01 0000 SAP BUILD TOOL 7.01
DI CHANGE MANAGEMENT SERVER 7.01 0006 SP006 CHANGE MANAGEMENT SERVER and SXMAN 7.00 701
DI COMPONENT BUILD SERVER 7.01 0006 SP006 COMPONENT BUILD SERVER 7.01
DI DESIGN TIME REPOSITORY 7.01 0006 SP006 DESIGN TIME REPOSITORY 7.01
FORUMS 7.01 0005 SP005 FORUMS 7.01
J2EE ENGINE BASE TABLES 7.01 0006 SP006 BASETABLES
J2EE ENGINE CORE TOOLS 7.01 0006 SP006 CORE TOOLS J2EE ENGINE
JAVA LOG VIEWER 7.01 0006 SP006 SAP JAVA LOG VIEWER 7.01
JAVA SP MANAGER 7.01 0006 SP006 JAVA SP MANAGER 7.00
KMC BASE COMPONENTS 7.01 0006 SP006 KMC BASE COMPONENTS 7.01
KMC COLLABORATION 7.01 0006 SP006 KMC COLLABORATION 7.01
KMC CONTENT MANAGEMENT 7.01 0006 SP006 KMC CONTENT MANAGEMENT 7.01
KMC UI LAYER 7.01 0006 SP006 KMC UI LAYER 7.01
KMC WEB PAGE COMPOSER 7.01 0006 SP006 KMC WEB PAGE COMPOSER 7.01
LIFECYCLE MGMT PORTAL 7.01 0006 SP006 LIFECYCLE MGMT PORTAL 7.01
LIFECYCLE MGMT TOOLS 7.01 0006 SP006 LIFECYCLE MGMT TOOLS 7.01
MI ADMINISTRATION 7.01 0006 SP006 MI ADMINISTRATION 7.01
MI DRIVERS 7.01 0006 SP006 MI DRIVERS 7.00
MI WD LAPTOP 7.01 0006 SP006 Net Weaver Mobile Infrastructure Web Dynpro LAPTOP 7.00
PDK PORTAL SERVICES 7.01 0006 SP006 PDK PORTAL SERVICES 7.00
PORTAL CORE SERVICES 7.01 0006 SP006 EPBC 7.01
PORTAL FRAMEWORK 7.01 0006 SP006 EPBC2 7.01
PORTAL PLATFORM 7.01 0006 SP006 EP - Portal Server PORTAL 7.01
PORTAL WEB DYNPRO 7.01 0006 SP006 PORTAL WEB DYNPRO 7.01
RTC 7.01 0006 SP006 RTC 7.00
RTC-STREAM 7.01 0006 SP006 RTC-STREAM 7.00
SAP CAF 7.01 0006 SP006 SAP CAF 7.01
SAP CAF-KM 7.01 0006 SP006 SAP CAF-KM 7.01
SAP CAF-UM 7.01 0006 SP006 SAP CAF-UM 7.01
SAP CPS BASIC (SCHEDULER) 7.01 0004 SP004 Job scheduling capabilities of SAP NetWeaver 7.01
SAP ESS 603 0006 SP006 SAP ESS 603
SAP INTERNET KNOWLEDGE SERVLET 7.01 0006 SP006 SAP Internet Knowledge Servlet 7.00 (SAP J2EE IKS)
SAP J2EE ENGINE 7.01 0006 SP006 SAP J2EE Engine 7.01
SAP J2EE ENGINE CORE 7.01 0006 SP006 SAP J2EE ENGINE CORE 7.01
SAP JAVA TECHNOLOGY S OFFLINE 7.01 0006 SP006 SAP JAVA TECHNOLOGY S OFFLINE SAP TECH S OFFLINE 7.01
SAP JAVA TECHNOLOGY SERVICES 7.01 0006 SP006 SAP JAVA TECHNOLOGY SERVICES (Schicht 3 Dummy) SAP JAVA TECH SERVICES
SAP MI CLIENT 7.01 0006 SP006 SAP Mobile Infrastructure Client 7.0
SAP MSS 600 0017 SP017 SAP MSS 600 (Manager Self Services)
SAP PCUI_GP 603 0006 SP006 SAP PCUI_GP 603
SAP SOFTW. DELIV. MANAGER 7.01 0000 SAP JAVA SL 7.01
SOFTWARE LIFECYCLE MANAGEMENT 7.01 0006 SP006 SOFTWARE LIFECYCLE MANAGER 7.01
UME ADMINISTRATION 7.01 0006 SP006 UME ADMINISTRATION 7.01
UWL COLL PROCESS ENGINE 7.01 0006 SP006 UWL COLL PROCESS ENGINE 7.01
VISUAL COMPOSER BASE 7.01 0006 SP006 VISUAL COMPOSER BASE 7.00
VISUAL COMPOSER BI KITS 7.01 0006 SP006 VISUAL COMPOSER BI KITS 7.00
VISUAL COMPOSER FLEX 7.01 0006 SP006 VISUAL COMPOSER FLEX 7.00
VISUAL COMPOSER FRAMEWORK 7.01 0006 SP006 VISUAL COMPOSER FRAMEWORK 7.00
VISUAL COMPOSER GP KITS 7.01 0006 SP006 VISUAL COMPOSER GP KITS 7.00
VISUAL COMPOSER XX KITS 7.01 0006 SP006 VISUAL COMPOSER XX KITS 7.00
WEB DYNPRO EXTENSIONS 7.01 0006 SP006 WEB DYNPRO EXTENSIONS 7.01
I expect to see more than the 6 previously mentioned files available for download, also the option for EHP2 which I know is available, or am I wrong in expecting this. -
SAP Solution Manager ABAP or JAVA or ABAP+JAVA ?
Hello.
I want to install Solution Manager for use Maitenance Optimizer ( accept download baskets, configure other SAP system, support packages ...).
I wanted to know if installing ABAP instance is enough? or I have to install Java also?
Regards,
AmitAmit,
SAP Solution Manager is separate application. You need ABAP+Java stack to use Maintenance Optimizer.
Please read documentation from following link
[http://www.service.sap.com/solutionmanager]
Best Luck,
Digesh Joshi -
Maintenance Optimizer Error "Value loss during allocation"
Hi Everybody,
like Error when Launching the Maintenance optimizer, i am facing the same problem with SolMan 7.1. Is there anything new?
System is new installed.
SOLMAN_SETUP is executed.
BC Set for MOPZ are activeded.
SMSY is arranged.
MOPZ is aborting after calculation the target with
On Web:
The followin error text was processed in SOL the systm: Value loss during allocation.
The error occurred on the application server _______ and in the work process. 7
The termination type was: RABAX_STATE
The ABAP call hierarchy was:
Method: GET_2ND_CHECK_RESULT of program CL_MO_SMP_ADAPTER=============CP
Method: LOAD_IMPACT_ASC of program /1BCWDY/06BL1VDEKWGU61REAXHZ==CP
Method: LOAD_22 of program /1BCWDY/06BL1VDEKWGU61REAXHZ==CP
Method: LOAD_CONTEXT of program /1BCWDY/06BL1VDEKWGU61REAXHZ==CP
Method: IF_COMPONENTCONTROLLER~LOAD_CONTEXT of program /1BCWDY/06BL1VDEKWGU61REAXHZ==CP
Method: HANDLEDEFAULT of program /1BCWDY/06BL1VDEKWGU61REAXHZ==CP
Method: IF_WDR_VIEW_DELEGATE~WD_INVOKE_EVENT_HANDLER of program /1BCWDY/06BL1VDEKWGU61REAXHZ==CP
Method: INVOKE_EVENTHANDLER of program CL_WDR_DELEGATING_VIEW========CP
Method: NAVIGATE of program CL_WDR_CLIENT_APPLICATION=====CP
Method: DO_NAVIGATION of program CL_WDR_WINDOW_PHASE_MODEL=====CP
On ST22:
Category ABAP Programming Error
Runtime Errors CONVT_DATA_LOSS
Except. CX_SY_CONVERSION_DATA_LOSS
ABAP Program CL_MO_SMP_ADAPTER=============CP
Application Component SV-SMG-MAI
Error analysis
An exception occurred that is explained in detail below.
The exception, which is assigned to class 'CX_SY_CONVERSION_DATA_LOSS', was not
caught in
procedure "GET_2ND_CHECK_RESULT" "(METHOD)", nor was it propagated by a RAISING
clause.
Since the caller of the procedure could not have anticipated that the
exception would occur, the current program is terminated.
The reason for the exception is:
Value "01200615325000005298|01200314694900012246:01200314694900010013" was
allocated in a field which is not long enough.
Therefore the target field could not store all information of
"01200615325000005298|01200314694900012246:01200314694900010013".Hello Espartaco,
I have the same problem, too. Have there been a response to your OSS message?
With best regards
Frank Lehmann -
Problem with Maintenance Optimizer...
Hello gurus,
I had a problem which I didn´t reached a solution...
When I create a new maintenance optimizer transaction and choose, on first step "Plan Maintenance", a type of Product Version I don´t have all systems which I configure on this Product Version on SMSY (System Landscape Directory).
For instance: I configure in SMSY the Product version (group) SAP ECC 6.0 which contains three systems DEV ; QAS ; PRD.
When I open/create a new maintenance optimizer transaction and choose the SAP ECC 6.0 I only see one system, the DEV system, within his, and I want to see all three systems which I configure in SMSY!
Help me please...! TKS
Best regards,
Joao DimasHi Vijay,
When I press in that URL - http://service.sap.com/~form/sapnet?_SHORTKEY=01100035870000679533& - does not appear anything about maintenance optimizer guide... it show me a notify "This folder needs to be reviewed" and I can´t see anything like you describe... I´m newest in SAP and still I have difficulties on search sometimes some things...
The link above, have you sure that's correct?
What´s the exactly name of document that you refer??
Thanks in advance,
Best regards,
Joao Dimas -
Error when Launching the Maintenance optimizer
Hello,
When launching the Maintenance optimizer of solman 7.1, in the step Cionfirm Target i got the following dump:
The followin error text was processed in SD1 the systm: Value loss during allocation.
The error occurred on the application server SD1ODYLSV1_SD1_00 and in the work process. 9
The termination type was: RABAX_STATE
The ABAP call hierarchy was:
Method: GET_2ND_CHECK_RESULT of program CL_MO_SMP_ADAPTER=============CP
Method: LOAD_IMPACT_ASC of program /1BCWDY/03N7KKG9LPWOUCQH4NOB==CP
Method: IF_COMPONENTCONTROLLER~LOAD_IMPACT_ASC of program /1BCWDY/03N7KKG9LPWOUCQH4NOB==CP
Method: ONACTIONLOAD_IMPACT of program /1BCWDY/03N7KKG9LPWOUCQH4NOB==CP
Method: IF_WDR_VIEW_DELEGATE~WD_INVOKE_EVENT_HANDLER of program /1BCWDY/03N7KKG9LPWOUCQH4NOB==CP
Method: INVOKE_EVENTHANDLER of program CL_WDR_DELEGATING_VIEW========CP
Method: IF_WDR_ACTION~FIRE of program CL_WDR_ACTION=================CP
Method: DO_HANDLE_ACTION_EVENTS of program CL_WDR_WINDOW_PHASE_MODEL=====CP
Method: PROCESS_REQUEST of program CL_WDR_WINDOW_PHASE_MODEL=====CP
Method: PROCESS_REQUEST of program CL_WDR_WINDOW=================CP
In the trace file of the Work process teh following error was found:
A ABAP Program CL_MO_SMP_ADAPTER=============CP .
A Source CL_MO_SMP_ADAPTER=============CM00A Line 19.
A Error Code CONVT_DATA_LOSS.
A Module $Id: //bas/720_REL/src/krn/runt/abxacnv.c#4 $ SAP.
A Function ab_xaCloseSimpleR Line 725.
A ** RABAX: level LEV_RX_STDERR completed.
A ** RABAX: level LEV_RX_RFC_ERROR entered.
A ** RABAX: level LEV_RX_RFC_ERROR completed.
A ** RABAX: level LEV_RX_RFC_CLOSE entered.
A ** RABAX: level LEV_RX_RFC_CLOSE completed.
A ** RABAX: level LEV_RX_IMC_ERROR entered.
A ** RABAX: level LEV_RX_IMC_ERROR completed.
A ** RABAX: level LEV_RX_DATASET_CLOSE entered.
A ** RABAX: level LEV_RX_DATASET_CLOSE completed.
A ** RABAX: level LEV_RX_ERROR_SAVE entered.
A ** RABAX: level LEV_RX_ERROR_SAVE completed.
A ** RABAX: level LEV_RX_ERROR_TPDA entered.
A ** RABAX: level LEV_RX_ERROR_TPDA completed.
A ** RABAX: level LEV_RX_PXA_RELEASE_RUDI entered.
A ** RABAX: level LEV_RX_PXA_RELEASE_RUDI completed.
A ** RABAX: level LEV_RX_LIVE_CACHE_CLEANUP entered.
A ** RABAX: level LEV_RX_LIVE_CACHE_CLEANUP completed.
A ** RABAX: level LEV_RX_END entered.
A ** RABAX: level LEV_RX_END completed.
A exceeded soft limit for RUDILOCKS (user: SAPADMIN , ta: )
I tried to find something about the *RUDILOCKS * without success.
Do you have any suggestion to resolve the issue?Hi,
Check SAP note 1505832.
Thanks
Sunny -
No System Found in Maintenance Optimizer
Hi,
I have installed solution manager (ST 400 SP09) and did apply the relevant notes to setup the Maintenance Optimizer.
I could able to see the Maintenance Optimizer button in Support Package and Stack Inbox.
(Transaction SOLUTION_MANAGER> select the Solution->operation ->Change Management ->Support package Stack)
But I found following message No Systems Found along with the following message
Change requests cannot be displayed or created, because the RFC connection has errors, or is not maintained.
Check whether the RFC connection to the Change Man agement system is under the key CHARM_DEST (APPLI field in the DESTINAT field), in the view BCOS_CUST. You need authorization for the cross-client view/table maintenance (S_TABU_DIS and S_TABU_CLI).
Check the RFC connection in the transaction SM59. If your SAP Solution Manager system is also your Change Manager system, the internal connection must be 'NONE'. You need authorization for the administration of RFC connections (S_RFC_ADM).
How do I proceed further? I wanted to see the Systems defined under SMSY transaction to be displayed here.
Can any body help me by providing the exact steps define the systems in Maintenance Optimizer and how to sync the components defined under SMSY with MOZ?
Regards
AratiHi Amit
This doesn't resolved my issue.I am getting following message
No entries exist, double-click for long text
Message no. SV065
Diagnosis
No entries were found when importing data from the database.
Procedure
To create new entries, choose the function Edit -> New Entries.
To recover deleted data, you must first display it with the function
Select -> Display Deleted, and then discard changes with Ctrl. + F2 or
the "Discard Change" button.
Thanks
Arati -
Configuring Maintenance Optimizer issue
Hi All,
This is the first time I am configuring SM 4.0. I am done with installation, and want to conigure maintenance optimizer.
I followed the IMG guide step by step.
But after all done, there are no systems listed under the maintenance optimizer of my Solution Landscape.
Instead I get a message:
<b>Change requests cannot be displayed or created, because the RFC connection has errors, or is not maintained.
Check whether the RFC connection to the Change Man agement system is under the key CHARM_DEST (APPLI field in the DESTINAT field), in the view BCOS_CUST. You need authorization for the cross-client view/table maintenance (S_TABU_DIS and S_TABU_CLI).
Check the RFC connection in the transaction SM59. If your SAP Solution Manager system is also your Change Manager system, the internal connection must be 'NONE'. You need authorization for the administration of RFC connections (S_RFC_ADM).</b>
Meanwhile I have issue with my J2EE engine not starting due to some UME issues, which I am working on parallely.
Please do let me know what would be the issue.
I have followed the note 990534 and doen with the BC sets.
But I am not sure where am I making a mistake.
One more doubt is, does maintenance optimizer connect to the SAP service market place through SAPOSS??? and am I not seeing anu system because my SLD is down. Please bear with my ignorance, I am a little lost here.
I have completed the solution landscape, logical component, etc.
Please help...
Regards,
SapfanHi JP,
My current SP levels are:
SAP_BASIS - 0011
SAP_ABAP - 0011
PI_BASIS 2005_11 - 0011
ST-PI 2005_11 - 0003
SAP_BW - 0011
SAP_AP - 0007
BBPCRM 5 - 0007
CPRXRPM - 0007
ST400 - 0010
ST-ICO - 0008
ST-SER - 0007
The issue is I did not connect to SAP yet, as I have only one RFC generated i.e. SAPOSS> Since my SAPRouter is not yet configured, I will connect to a valid SAPRouter once all the SM config is done.
I als got sone error in generating RFC for the main system when I used the wizard. I selected Change management and customizing directory and also selected Assign RFC for system monitoring.
I changed back the UME source to client 001, but still same.
Moreover the maintenance optimizer is not showing the satellite system.
I am really stuck.
Please let me know if you require more information.
I created the main system and defined the solution, as per the SPRO->Solution Manager -> Advanced Configuration -> Basic settings ->
I started this only after applying SP10.
Now I don see the systems both for Setup Solution monitoring and in maintenance optimizer.
WIll the system not reflect is the java ebngine is down???
Regards,
P.K -
Problem with Maintenance Optimizer - Solman EHP1
Hi All,
I have a solution manager 7.0 ehp1 system and maintenance optimizer does not work at all.
Initial configurarion and Basic configuration has been done - Tcode : Solman_Setup
A solution has been created and systems have been assigned to it, however when i launch create new maintenance
transaction it shows us the solution and the systems assigned under it.If i select our Production system and click on next
it comes up an error, saying the table does not contain any data. Do i need to do the SLM configuration for MOPZ to work?
Has anyone seen this error earlier. Any inputs would be of great help.
Regards,
Ershad Ahmed.Hi,
Though the error does not give much insight. There are some warnings which tells that configuration has to be done
Please find the warnings attached in the email.
Not able to find an active SLM for selected managed systems
No configured SLM
No common SLM system is regsitered for Managed Systems
The system / systems - SID have not beed registered in SLM
Instance -type missing in SMSY for an application server instance of system .
Regards,
Ershad Ahmed -
Maintenance optimizer configuration Steps
Dear All,
I am stuck with Maintenance optimizer configuration.
Can somone provide a usefull link for the same i am using SOLMAN 4.0 with SP 15.
Best of regards,
Gaurav SoodHi ,
Here are the steps :-
MAITENANCE OPTIMIZER STEPS
1) Create the system in solution manager (Tr.code-SMSY)
2) For this System to create the rfc destinations.
3) Create the logical component for system.
4) Maintain technical settings of OSS in the transaction code: OSS1
5) In TR code AISUSER maintain the user and OSS id
6) In DSWP transaction codeu2014in settings-global settings have to maintain OSS id and Password.
7)go to tr code DSWPu2014changemanagementu2014support packagesu2014click on maintenance optimizeru2014select the systemu2014continue-confirm files in download basketu2014complete transaction.
Thanks
Abullais -
Maintenance Optimizer - ConfigTool.sh - SAP NetWeaver 7.0
Hi Everybody,
First I wanted to set up my MOPZ to do this I have to create a RFC "SAPSLDAPI"
Until there no problem but the next step become a little more problematic.
I have to run the admin tool /usr/sap/SOL/..../j2ee/admin/go.
Unfortunatly I lost the password's J2EE_ADMIN, no problem google is your best friend and then I tried to run the config tool. Oh big surprise
The java class not found: com.sap.offline.OfflineToolStart
What can i do to fix this problem?
Note 1024932 - Maintenance Optimizer: Collective Note
http://help.sap.com/saphelp_nw70/helpdata/en/b7/341241d71cd349e10000000a1550b0/content.htm
Edited by: Hafid CHEBRAOUI on Jan 14, 2009 4:22 PMIt sounds like you have two different issues here.
MOPZ
And Java Stack not starting.
Maintenance optimizer requires that your connection to SAP is in tact first through the saprouter. Do you have all of that in place and is your rfc connections for SAP_OSS and SAPNET_RFC working.
SAPSLDAPI is a connection for the SLD not for the maintenance optimizer.
The link you put below doesn't have anything to do with configuring maintenance optimizer. The ossnote you posted is a collective note for maintenance optimizer and points you to spro to follow the instructions.
Review https://websmp108.sap-ag.de/solman-mopz
Review ossnotes 990534 and 1024932
try running SE38 SM_PREP_MAINTENANCE_OPTIMIZER That may give you some assistance.
Anyone that is going to download using the maintenance optimizer needs to exist in transaction AISUSER
As for the Java stack.
It sounds like your path is not right. Did you update your path environment variables with the installation directory of java? Check that java -version is working from the <sid>adm login.
Lee -
Re: XI contains both ABAP + Java system?
Hi friends,
I have a question regarding XI. XI contains both ABAP + Java system?.
Any help would be greatly appreciated
Thanks,
KrishnaHi Krishna,
XI does not contains ABAP + JAVA system instead it is installed on Web Application Server which has both ABAP Engine and Java engine.
XI has components which are deployed on JAVA Engine as well as on ABAP engine.
Some Components installed on JAVA Engine are:
Integration Builder
Adapter Engine
Runtime Workbench etc.
Some Components installed on ABAP Engine are:
Integration Engine
User Maintenance (it is on Java engine also) etc.
Thanks & Regards,
Varun Joshi
Maybe you are looking for
-
Thunderbolt to FireWire Adapter: no bus power?
I got my TB to FW adapter yesterday and it worked fine with a HD using wall power but will not power a portable Iomega drive via the FW bus only. The drive light will flash once every few seconds so some power is going through, but not enough to spin
-
How to use the full specs of the G3010 with Windows 8.1. I just install it and can not scan slides or films. In the dialog box all the options are not available, only "regular" scan. Thanks for the cooperation. Lemicu
-
Can't migrate from G5 running Leopard!
When I try migrating over Ethernet, I get an error on the Mavericks machine: "The selected source cannot be used for migration. Your other Mac is not running the latest version of OS X. Please run Software Update on your other Mac and try again." Whe
-
How do i find a user manual for i Pad Model A1219
where do i find a user manual for an iPad model A1219?
-
Hi there, We're using the workflow aplication on the ECM and we want to send a email at the end of the workflow, notifying an entity that the content has been rejected or approved but we don't know how to do this. We also have tried to test if the em